Manuel d'utilisation / d'entretien du produit JiMS-190 du fabricant Jensen
Aller à la page of 16
® DOCKING DIGIT AL MUSIC SYSTEM FOR iPod OWNER'S MANUAL JiMS-190 ® (iPod Not Included) PLEASE READ THIS OPERATING MANUAL COMPLETEL Y BEFORE OPERATING THIS UNIT AND RET AIN THIS BOOKLET FOR FUTU.
.
® DEAR JENSEN CUSTOMER IMPORTANT SAFETY INSTRUCTIONS COMPLIANCE WITH FCC REGULATIONS PRODUCT FEATURES INSTALLA TION LOCATION OF CONTROLS RADIO OPERATIONS ® iPod DOCKING AUXILIARY INPUT CLOCK AND CAL.
Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers.
3 7.Object and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents located on the product. 8.Attachments Do not use attachments no recommended by the product manufacturer. 9.Lightning and Power Surge Protection Unplug the unit from the wall outlet and disconnect the periods of time.
4 INSTALLA TION PRODUCT FEA TURES Clock Back-up Batteries Installation 1.Open the battery compartment door located at the bottom of the unit. 2.Install two DC1.5V 'AAA' (UM-4) batteries (not included) in the battery compartment following the polarity markings shown on it.
5 LOCATION OF CONTROLS Bottom view T op view Main Unit Rear view 21 22 1 2 12 7 11 6 5 10 4 3 8 9 Front view 13 15 15 14 ® 1.iPod Dock ® 2.iPod Docking Connector 3. POWER On/Off Button T o turn the unit on or off 4. VOLUME +/- Buttons Adjust the volume level up or down 5.
6 Remote Control LOCATION OF CONTROLS 1.Infra-red Transmitter 2.POWER On/Off Button 3.VOL +/- Button 4.FUNCTION Button 5.ALARM On/Off Button 6.SNOOZE/LIGHT Button 7.TUN Up/Down Buttons for Down, for Up 8.CH +/- Buttons 9.MEM Button 10.MODE Button 11.SLEEP Button ® 12.
7 RADIO OPERATIONS FM Antenna Connect the detachable FM Antenna Wire to the FM Antenna T erminal as instructed in the section “INSTALLA TION”. Fully extend the FM Antenna Wire for the maximum reception. Radio Tuning 1.Press the POWER button to turn on the unit.
8 If the docking port will not be used for an extended period of time, it is recommended to cover the docking port by using the “Dock Cover” insert (included).
9 AUXILIARY INPUT The auxiliary input cable and plug are built in the unit and allows users to connect their CD player, MP3 player or other digital audio players to the unit. 1.Keep turning the Cord Retracting Wheel, located at the rear of the unit, to the right and pull out the AUX IN Cable located next to the wheel.
10 The clock and calendar can be set in Power Off mode. Clock Setting 1.Press the MODE button 3 times, the clock starts to flash. 2.Press the TUN +/- button to set the hour. 3.Press the VOL +/- button to set the minute. 4.Press the MEM button to confirm the settings.
11 ALARM OPERATIONS Wake to Radio ( RAD) - The radio will automatically turn on when the alarm time is reached. It starts softly and becomes gradually louder. - The radio alarm will keep for 60 minutes and then will automatically shut off. - To stop the radio alarm sound immediately , press the ALARM On/Off button once.
12 - Do not subject the unit to excessive force, shock, dust or extreme temperature. - Do not tamper the internal components of the unit. - Clean your unit with a damp (never wet) cloth. Solvent or detergent should never be used. - Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.
TROUBLESHOOTING GUIDE Symptom Possible Problem Solution The unit does not respond (no power) AC Adaptor is not plugged into a wall outlet or the connector is not plugged into the power supply jack on the back of the unit. Plug the AC adaptor into a wall outlet and plug the connector into the supply jack on the unit.
14 Printed in China SPECIFICATIONS Power Supply Power Adaptor (included) Battery Back-up for Clock Remote Control Frequency Range USA's Radio Broadcast System EU's Radio Broadcast System Japan's Radio Broadcast System Input: AC120V/60Hz Output: DC10V/1400mA DC1.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Jensen JiMS-190 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Jensen JiMS-190 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Jensen JiMS-190, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Jensen JiMS-190 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Jensen JiMS-190, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Jensen JiMS-190.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Jensen JiMS-190. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Jensen JiMS-190 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.