Manuel d'utilisation / d'entretien du produit 927566 du fabricant Hustler Turf
Aller à la page of 45
.
This manual applies to the following Hustler equipment lines: Hustler Z/Super Z Hustler Z Shibaura Diesel Hustler ATZ To the new owner The purpose of this manual is to assist owners and operators in maintaining and operating the Hustler Z tractor and deck.
601656_1108 2.
HUSTLER Z/HUSTLER Z SHIB A URA DIESEL/SUPER Z/HUSTLER A TZ TWO YEAR LIMITED W ARRANTY FOR TRACT ORS AND DECKS (THREE YEAR LIMITED W ARRANTY ON DECK SPINDLE BEARING & DECK GA UGE FORK BEARING) OR F.
601656_1108 unreasonable use, accident, negligence or misuse ● Repairs or replacement resulting from the use of unauthorized parts, accessories or attachments ● Repairs or replacement as the resul.
This safety alert symbol is used to call attention to a message intended to provide a reasonable degree of PERSONAL SAFETY for operators and other persons during the normal operation and servicing of this equipment. DANGER – denotes immediate hazards which WILL result in severe personal injury or death.
Hydraulic fluid escaping under pressure can penetrate skin. Hydraulic fluid may also cause infection in a minor cut or opening in the skin; if exposed to hydraulic fluid, see a doctor at once. Before applying pressure to hydraulic system, make sure all connections are tight and all hoses and lines are in good condition.
601968 601967 • Avoid hydraulic fluid escaping under pressure • Hydraulic fluid escaping under pressure can penetrate skin. • Hydraulic fluid may also cause infection in a minor cut or opening in the skin; if exposed to hydraulic fluid, see a doctor at once.
601791 WARNING: Read Owner’s Manual and decals before attempting to operate this machine. • Mow a safe distance (minimum of 10 feet) away from drop-offs, retaining walls, drainage ditches, embankments, water, and other types of hazards to avoid a wheel dropping over the edge or to avoid the ground from breaking away.
9 601656_1108 601792 WARNING: This structure’s protective capability may be impaired by structural damage, overturn, or alteration. If any of these conditions occur, this structure must be replaced. 601792 • Avoid crushing, use seat belt. • Do not jump if machine tips.
601790 A - Fast B - Slow C - Choke D - Mower blade engage/disengage switch E - Ignition switch - insert key F - OFF G - ON or ON/GLO Plug H - If warning light comes on, check engine oil I - Before sta.
C (5 o ) D (10 o ) E (15 o ) Line A Line B Slope Guide Lines F (25 o ) - Hustler A TZ only 601656_1108 1. Hold this sheet of paper in front of you. Make sure that line A is horizontal. 2. Align line B with a vertical surface such as a pole, tree or building.
601656_1108 12.
Safe Operating Practices Some of the following safety instructions are from ANSI Standard B- 71.4-2004 while others are specific to the Hustler Mid Mount Z line. This product is capable of amputating hands and feet and throwing objects. Always follow all safety instructions to avoid serious injury or death.
601656_1108 ▲ Keep all movement on slopes slow and gradual. Do not make sudden changes in speed or direction. ▲ Avoid starting and stopping on a slope.
IMPORTANT: When access is required under the seat platform and the seat is equipped with the optional arm rests, make certain to place the control arms in the park brake position and pivot the arm rests upward before placing the seat platform in the full forward position to prevent arm rest damage.
601656_1108 temperature. If the coolant reaches an unsafe level during operation, shut down the machine as soon as possible. Never risk continued operation when the gauge needle is in the high range; high temperatures can severely damage the engine.
Safety start interlock system The tractor is equipped with a safety start interlock system consisting of the park brake switches, seat switch, and deck clutch switch. Check tractor safety start interlock system daily, prior to operation. This system is an important tractor safety feature.
Moving tractor with stalled engine If it becomes necessary to move the tractor when the engine is inoperative, the hydraulic pumps are equipped with bypass valves. Before moving the unit, turn bypass valves counter clockwise one-half to one revolution.
WARNING: Always wear your seat belt unless the tractor is not equipped with a ROPS or if the ROPS is folded down. In this case, the seat belt should never be worn. WARNING: To minimize chance of injury or death from rollover: keep ROPS in the raised and locked position and use the seat belt.
WARNING: The ROPS structure’s protective capability may be impaired by structural damage, overturn or alteration. Do not remove or alter any of the ROPS parts. Do not attempt to weld or straighten ROPS. Failure to adhere to these instructions could result in severe injury or death.
Use the control levers to control ground speed rather than engine rpm. Keep blades sharp. Many professional mowing companies have additional sets of blades and change blades twice a day: once in the morning and again at noon. Many problems with incorrect cutting patterns a re due to dull blades or blades which have been sharpened incorrectly.
If the machine’s forward motion must be stopped while mowing, a clump of grass clippings may drop onto your lawn. To avoid this, move onto a previously cut area with the blades engaged. WARNING: Never direct discharge of material from mower deck towards bystanders.
Figure 3-20 Tilt seat switch 601656_1108 23.
601656_1108 24.
MAINTENANCE & ADJUSTMENTS Safe Servicing Practices This product is capable of amputating hands and feet and throwing objects. Always follow all safety instructions to avoid serious injury or death. Service ▲ Unless specifically required, DO NOT have engine running when servicing or making adjustments to tractor.
Hydraulic system IMPORTANT: Never use hydraulic or automatic transmission fluid in this system; use only motor oil as specified. Remember, dirt is the primary enemy of any hydraulic system. WARNING: Hydraulic oil escaping under pressure can penetrate skin.
Change hydraulic system filter element after first 50 hours of tractor operation, then replace filter and oil in reservoir every 500 hours thereafter. Fig. 4-2 The system filter is located in front of the hydraulic reservoir. A standard oil filter wrench is used to change filter, threads are right handed.
hours on a Hustler Z Shibaura diesel unit), per the engine manufacturer’s recommendations after that. If tractor is being operated in extremely dirty conditions, then it is recommended oil be changed more frequently. Engine air filter Perform engine air filter maintenance per the Service Interval chart shown elsewhere in this manual.
air to pass. The mowing conditions will determine the frequency of air filter element changing. Air restriction indicator Some Hustler units have an air restriction indicator installed in the air cleaner. Fig. 4-9 Replace the element whenever the restriction indicator reaches the change filter red line.
Do not re-use spindle bolts which have stripped, worn or undercut threads. Torque bolts on spindles to 118 foot-pounds (160.0 N m) when reinstalling blades. IMPORTANT: When mounting blades, rotate them after installation to ensure blade tips do not touch each other or sides of the mower.
31 601656_1108 Figure 4-15 Cap screw Upper control lever Lower control lever.
601656_1108 32.
WEEKLY MONTHLY ANNUALLY OR SERVICE AT OR 50 OR 100 500 INTERVALS INDICATED HOURS HOURS HOURS Verify safety start interlock system Daily Check coolant level Daily Visually inspect unit for loose hardware and/or damaged parts Daily Visually inspect tires Daily Check oil level, engine (1) Daily or every 4 hrs.
601656_1108 34 4 1a 2c 3 10 Hustler Z/Super Z Maintenance Locator Chart 1a. Engine Oil Fill & Dipstick (Kawasaki & Honda) 1b. Engine Oil Fill & Dipstick (Kohler) 2a. Fuel Filter 2b. Fuel Filter (927053 & 927061) 2c. Fuel Filter (Kawasaki liquid cooled) 3.
Viewed from bottom of tractor 1. Engine Oil Dipstick 2. Fuel Filter 3. Engine Air Cleaner 4. Engine Oil Drain Plug 5. Battery 6. Fuel Tanks 7. Hydraulic Oil Reservoir 8. Hydraulic Oil Filter 9. Gauge Wheel Bearing Zerks (2) 10. Engine Oil Filter 11. Deck Height Pivot Zerks (4) 12.
601656_1108 36 Figure 4-19 Hustler Z/Super Z/ATZ Rear Discharge Deck Maintenance Locator Chart 1 4 1 2 3 3 4 3 Rear dischar ge deck Figure 4-18 2 1 1 4 3 3 3 4 4 Hustler Z/Super Z/ATZ/Hustler Z Shibaura Diesel Rear Discharge Deck Maintenance Locator Chart 1.
XR7 Deck Maintenance Locator Chart 1. Deck Pusher Arm Zerks (2) 2. Deck Belt 3. Spindle Housing Zerk (3) 4. Blades 4 4 1 1 3 3 3 2 1 4 1 2 3 3 4 3 54”/66”/72” XR7 deck 60” XR7 deck Figure 4-20.
601656_1108 38 Hustler ATZ Maintenance Locator Chart 6 10 2 4 3 16 9 11 9 5 12 7 6 12 11 11 16 1 13 8 13 14 15 Figure 4-21 1. Engine Oil Fill & Dipstick 2. Fuel Filter 3. Engine Air Cleaner 4. Engine Oil Drain Plug 5. Battery 6. Fuel Tanks 7. Hydraulic Oil Reservoir 8.
Hustler Z/Super Z/Hustler Z Shibaura Diesel/Hustler A TZ TROUBLESHOO TING The majority of operating problems that occur with a system can be traced to improper adjustments or delayed service. A consistently applied preventative maintenance program, as outlined in the maintenance section of this manual, will prevent many problems.
601656_1108 40.
601656_1108 41 This section contains sources of additional literature concerning your tractor. Literature should be ordered from your Hustler dealer or direct from indicated source. Parts Manuals If you would like to order a Parts Manual for a particular tractor, the Hustler part number for that manual is listed in the following chart.
601656_1108 42.
INDEX PAGE Anti-scalp wheels .........................................................................22 ATZ tilt seat .................................................................................22 BAC-VAC mounting ...............................
601656_1108 44.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Hustler Turf 927566 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Hustler Turf 927566 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Hustler Turf 927566, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Hustler Turf 927566 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Hustler Turf 927566, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Hustler Turf 927566.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Hustler Turf 927566. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Hustler Turf 927566 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
