Manuel d'utilisation / d'entretien du produit 3C509B-TP du fabricant HP (Hewlett-Packard)
Aller à la page of 46
Etherlink IIIB ISA Network Interface Card (10BT) 3C509B-TP Installation Guide.
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
1 Connecting to a Netware 3.12 Server Windows for Workgroups 1 Connecting to a Netware 3.12 Server Windows for Workgroups Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver.
1 Connecting to a Netware 3.12 Server Windows for Workgroups 4 Select “CONFIGURE NIC,” and verify the resource settings listed above under the heading “Device Configuration.” 5 If changes are required, save those changes and exit. 6 Remove the 3com cards driver diskette and insert Netware client for DOS and MS-Windows disk 1.
1 Connecting to a Netware 3.12 Server Windows for Workgroups 9 Select 16-bit LAN Drivers and hit the enter key. 10 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER” and hit enter. 11 Insert the 3COM Etherlink 3C509 Ethernet card and drivers disk, set the path to “A:NWCLIENT” and press enter.
1 Connecting to a Netware 3.12 Server Windows for Workgroups.
1 Connecting to a Netware 3.12 Server Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. • Vectra VL8 Driver Name: W95EL5X9.INF Size: 16KB Date: 6/11/97 • Vectra VL7 Driver Name: Elnk.
1 Connecting to a Netware 3.12 Server Windows 95 SR2 5 If changes are required, save those changes and exit. 6 Remove the 3com cards driver diskette and restart the machine. 7 After windows loads, click on “Start,” to “Settings” and over to “Control Panel.
2 Connecting to a Netware 4.11 Server Windows for Workgroups 2 Connecting to a Netware 4.11 Server Windows for Workgroups Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver.
2 Connecting to a Netware 4.11 Server Windows for Workgroups 6 Remove the 3COM cards driver diskette and insert Netware client for DOS and MS-Windows disk 1. If you are using a Vectra VL8, go straight to step 7. If you are using a VL7 or VE7/VE8, finish the installation by using the instructions below.
2 Connecting to a Netware 4.11 Server Windows for Workgroups 10 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER” and hit enter. 11 Insert the 3COM Etherlink 3C509 Ethernet card and drivers disk, set the path to “A:NWCLIENT” and press enter.
2 Connecting to a Netware 4.11 Server Windows for Workgroups.
2 Connecting to a Netware 4.11 Server Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. Vectra VL8 and VE7/VE8 Driver Name : W95EL5X9.INF Size: 16KB Date: 6/11/97 • Vectra VL7 Driver Name: Elnk.
2 Connecting to a Netware 4.11 Server Windows 95 SR2 6 Remove the 3com cards driver diskette and restart the machine. 7 After windows loads, click on “Start,” to “Settings” and over to “Control Panel.” 8 Double click on “Network” and select “Add.
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver.
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 7 After windows loads, open the “NETWORK” Program Group, and double- click on “Network Setup.” 8 Select the “Networks” button in the “Network Setup” dialog box. 9 Click on the “Install Microsoft Windows Network:” option, and click “OK.
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11.
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11.
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2. • 3COM Etherlink 3C509-B Ethernet card and drivers disk ver 5.0. • Vectra VL8 and VE7/VE8 Driver Name: W95EL5X9.INF Size: 16KB Date: 6/11/97 • Vectra VL7 Driver Name: Elnk.
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 under the heading “Device Configuration.” 6 If changes are required, save those changes and exit. 7 Remove the 3Com Software driver diskette and reboot the machine. 8 Click on “Start” and point to “Settings”, then select the “Control Panel.
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 an HP preloaded HDD, set the path to “C:MASTERSWIN95SYSTEMCABS”) 21 To complete the installation, select “Yes” to restart your computer.
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 Windows NT Workstation Version 3.51 Requirements • HP Vectra with Microsoft Windows NT Workstation 3.51 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 If you are using a Vectra VE7/VE8, follow the instructions below to complete the installation. a If changes are required, save those changes and exit. b Remove the 3COM software driver diskette and reboot the machine.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 q At the "TCP/IP Configuration" screen, choose to use DHCP or enter your TCP information and click on "OK." (If you do not have the required information, contact your network administrator.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 19 Choose to install all applicable TCP/IP options and select “Continue.” (If you do not have the required information, contact your network administrator) 20 At the “Network Settings” dialog box, click on “OK.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0 Windows NT Workstation 4.0 Requirements • HP Vectra with Windows NT Workstation 4.0 Service Pack 3. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver 5.0. Driver Name: Elnk3.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0 6 If changes are required, save those changes and exit. 7 Remove the 3com cards driver diskette and reboot the machine. 8 Power on the machine and allow it to boot to Windows NT Workstation 4.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0 25 When “Windows NT is now ready to start the network…” click on “Next.” 26 Specify your Computer Name, Workgroup or Domain and click on “Next.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0.
4. Connecting to a Windows NT Server 4.0 Windows for Workgroups Ver. 3.11 4. Connecting to a Windows NT Server 4.0 Windows for Workgroups Ver. 3.11 Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver.
4. Connecting to a Windows NT Server 4.0 Windows for Workgroups Ver. 3.11 7 After windows loads, open the “NETWORK” Program Group, and double- click on “Network Setup.” 8 Select the “Networks” button in the “Network Setup” dialog box. 9 Click on the “Install Microsoft Windows Network:” option, and click “OK.
4 Connecting to a Windows NT Server 4.0 Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2. • 3COM Etherlink 3C509-B Ethernet card and drivers disk ver 5.0. Vectra VL8 and VE7/VE8 Driver Name: W95EL5X9.INF Size:16KB Date: 6/11/97.
4 Connecting to a Windows NT Server 4.0 Windows 95 SR2 6 If changes are required, save those changes and exit. 7 Remove the 3Com Software driver diskette and reboot the machine. 8 Click on “Start” and point to “Settings”, then select the “Control Panel.
4 Connecting to a Windows NT Server 4.0 Windows 95 SR2 “C:MASTERSWIN95SYSTEMCABS”) 22 To complete the installation, select “Yes” to restart your computer.
4 Connecting to a Windows NT Server 4.0 Windows 95 SR2.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation Version 3.51 Windows NT Workstation Version 3.51 Requirements • HP Vectra with Microsoft Windows NT Workstation 3.51 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation Version 3.51 7 Remove the 3com software driver diskette and reboot the machine. 8 After windows loads, open the “Main” program group, double-click on “Control Panel” icon. 9 Double click on the “Network” icon and agree to install Windows NT Networking on your computer.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation Version 3.51 administrator) 23 At the “Domain/Workgroup Settings” Dialog Box, click on “OK” to accept the default “Workgroup” as your workgroup name.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation Version 3.51.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 Windows NT Workstation 4.0 Requirements • HP Vectra with Windows NT Workstation 4.0 Service Pack 3. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver 5.0. Driver Name: Elnk3.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 6 If changes are required, save those changes and exit. 7 Remove the 3com cards driver diskette and reboot the machine. 8 Power on the machine and allow it to boot to Windows NT Workstation 4.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 25 When “Windows NT is now ready to start the network…” click on “Next.” 26 Specify your Computer Name, Workgroup or Domain and click on “Next.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0.
.
V ersion Number 3Com 3c509 Rev .1.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté HP (Hewlett-Packard) 3C509B-TP c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du HP (Hewlett-Packard) 3C509B-TP - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation HP (Hewlett-Packard) 3C509B-TP, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le HP (Hewlett-Packard) 3C509B-TP va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le HP (Hewlett-Packard) 3C509B-TP, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du HP (Hewlett-Packard) 3C509B-TP.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le HP (Hewlett-Packard) 3C509B-TP. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei HP (Hewlett-Packard) 3C509B-TP ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
