Manuel d'utilisation / d'entretien du produit AL500 du fabricant Harmar Mobility
Aller à la page of 36
AL500 Universal Power Chair Lift AL100 Universal Scooter Lift AL550 A utomatic Power Chair Lif t AL 560 A uto Hold Down P .C. Lift Outside Lif t Capacity: 350 lbs Capacity: 350 lbs Capacity: 350 lbs C.
PLATFORM KEEPER WELDE D TO P LATF OR M LIFT AL030 - Manual Wheelchair Lift LIFT BODY HITCH ADAPTER and Stabil izer HARDWARE PACK HITCH POST Unpacking the Lif t Y our Universal Outside Lift was factory pre- assembled to require little assembly before installa tion.
BEGIN ROUTING THE VEHICLE HARNESS A T THE BA TTERY Attach the black wire to the negative terminal on the battery. Do not attach the red wire yet. Important Reminder: Never attempt to attach the wire harness to a secondary power source. The harness requires direct connection to the battery.
V ehicle Hitch lbs Must NOT Exceed Hitch Manufacturer's Max T ongue Weight OR X lbs Chair / Scooter IF USED 40 lbs Swing Away Not for AL030 T o install an Outside Lift on a vehicle, the vehicle must be capable of accepting a Class 2 or Class 3 hitch.
AL123 Standard Class 3 AL125 Class 3 Extra long H124 Class 3 Short AL1232 2in Drop Class 3 AL1236 6in Drop Class 3 H128 Class 2 Short AL1235 5in Drop Class 3 AL1265 4in Drop Class 2 AL127 Class 2 Extra long AL126 Standard Class 2 A Hitch Adapter is the part of the lift that plugs into a vehicle's trailer hitch.
OR Attach Lift to Hitch Post or Swing A way SWING AW A Y HITCH ADAPTER Measure from Hitch Bar to ground In order to determine how to assemble the Hitch Post and Hitch Adapter , the distance from the bottom of the hitch to the ground must be measured. Determine which set of holes to use to bolt together the Hitch Post and Hitch Adapter .
M O B I L I T Y For AL030 ONLY Bumper Mount ( Be sure to comply with vehicle's bumper rating ) Flat Bar S tyle ( Be sure to comply with vehicle's bumper rating ) Omit stabilizer Do not attem.
Power Chair or Scooter Preparation AL600 & AL690 ALA580 U-BOLT H ARDWAR E KIT ANCHOR U-BOLTS: THE U-BOLTS ARE TO BE USED WITH POWER CHAIRS OR SCOOTERS THA T DO NOT HAVE A CENTER SEA T POST . ON THIS TYPE OF CHAIR, THE SEAT IS NORMALLY ATT ACHED TO A TUBULAR FRAME.
AL550 only CHOOSING A LOCATION and MOUNTING THE DOCKING DEVICE PLATE Find approximate center of the chair The closer the plate is positioned to the drive wheels, the easier the chair will be to engage the Locking Device Drive wheel Use existing holes where ever possible.
AL550 only SETTING DOCKING DEVICE HEIGHT 0.25" 0.25" 1.00" 1.00" 0.25" 0.25" 1.00" 1.00" 1.00" 1.00" 1.00" 1.00" 1.00" 1.00" 0.25" 0.25" 1.00" 1.00" 0.50" 0.
DO NOT With platform on the ground, drive scooter onto platform , from left (driver's side ) to right, until the rear wheels are located in the rear wheel spreader bar assembly . S top when the rear tires conta ct the ramp on the platform. Raise the platform on either lift u ntil the motor's clutch is heard ( top of travel ).
Loosen nuts here Slide arm up or down tube Tighten after adjustment N O I S N E T T S U J D A LIFT SHOULD HOLD WHEELCHAIR FIRMLY WITH THE PLATFORM FULLY RAISED ( RAISED UNTIL MOTOR RATCHETING IS HEARD ) The hinge points are equipped with tensioning washers.
LIFT PREPARA TION AL 560 3/16 “ ALLEN WRENCH REQUIRED FOR ADJUSTMENT PURPOSES, ALL PLA TFORM COMPONENTS ARE SHIPPED LOOSE AND MUST BE FIRMLY TIG HTENED IF NECESSAR Y, T HE COMPONENTS MAY BE RE-ARRAN.
LIFT PREPARA TION HOLD DOWN ARM HEIGHT ADJUSTMENT AL 560 LOOSEN BOL TS TIGHTEN BOL TS HIGHER ARM SETTINGS CAN BE ACHIEVED BY REMOVING TOP SHAFT COLLAR, RETRACTING T HANDLE AND RE-INSERTING ARM FROM ABOVE. THIS METHOD ALLOWS THE RED “T” HANDLE TO REMAIN ON THE SAME SIDE AS THE KEY AND TOGGLE SWITCHES.
REAR WHEELS FRONT WHEELS General Operating Instructions: Turn the key switch to the ON position. With the toggle switch, raise and lower the platform a s needed. Pushing the switch downward will cause the platform to lower. The plat form will first unfold to the horizontal posit ion, then continue lowering to the ground.
T o unload the power chair, simply turn ON the power switch and push the UP/DOWN toggle switch to the down position. Hold the s witch down until the platform just touches and is level to the ground. Press the red release button on the Anchor S trap Base to release the tension and unhook the strap from the chair.
ON DOWN UP THREE WA YS TO VERIFY YOUR CHAIR IS SUCCESSFULLY LOCKED DOWN 1) AUDIBLE "CLICK or POP" SOUND 3) REVERSE TEST 2) VISUAL INDICAT OR SLOW NOT LOCKED LOCKED The yellow indicator will extend and stay extended when the chair is successfully locked in place.
V ehicle Hitch OPERA TOR RESPONSIBILITY - AL 550 VERIFY THE CHAIR HAS BEEN LOCKED INTO THE DOCKING ST A TION BY A TTEMPTING TO DRIVE CHAIR OFF IN REVERSE THE DOCKING STA TION WILL “CLICK” or “PO.
TO RELEASE CHAIR Slide knob this direction Slowly back chair off platform NOTE: During transport, vibration may cause the chair to tighten itself in the locking device, making the release knob difficult to slide. T o overcome this, simply drive the chair forward a bit.
Insert Key and switch to "ON" position Press down on T oggle switch momentarily. Once platform has been lowered at least an inch, unfold the platform. Continue lowering to the ground. Drive scooter onto platform as shown. Raise platform until hold down foot depresses scooter's deck or until lift's motor ratchets.
1 Insert Key and switch to "ON" position Press down on T oggle switch momentarily. Once platform has been lowered at least an inch, unfold the platform. Continue lowering to the ground. 2 ON DOWN UP "PLA TFORM KEEPER" NOTE: The Platform will not be allowed to unfold until the platform has been lowered at least an inch.
V ehicle Hitch OPERATION LOADING THE WHEELCHAIR AL030 ON DOWN UP "PLA TFORM KEEPER" NOTE: The Platform will not be allowed to unfold until the platform has been lowered at least an inch. WE LDED TO PLAT FORM Insert Key and switch to "ON" position Press down on T oggle switch momentarily.
OPERATION Drive the Chair onto the platform taking care to stop when the drive wheels fall between the bars in the platform. 2 AL 560 LOADING A POWER CHAIR ON DOWN UP 1 Insert Key and switch to "ON" position Press down on T oggle switch and the platform will unfold.
OPENING THE SWING AW A Y: IMPORT ANT CAUTION!! Many scooter and chair owners require access to the rear of a vehicle. T o accomplish this a Swing Away o ption is added to the lift installation. Thi s allows the complete lift t o be conveniently and easily swung away from the back of the vehicle and allow easy access to the trunk or lift gate.
Safety & Maintenance Inspect the condition of your lift often. If any parts are worn or damaged DO NOT USE THE LIFT . Immediately contact the dealer you purchased the lift from for repairs. Caution: Keep feet and any other objects out from under the platform as it lowers.
T roubleshooting Guide Check the attachment of the Hitch Adapter to the Hitch Post on the back of the lift . The normal range of operation for the lift is 5 to 18 inches to the bottom of the hitch. The lift should be installed at the highest position possible.
EXPLODED VIEW - AL-010/050 + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 27.
V ehicle Hitch EXPLODED VIEW - AL-030 + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 28.
EXPLODED VIEW - AL-100 + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 29.
V ehicle Hitch EXPLODED VIEW - AL-300 + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 30.
EXPLODED VIEW - AL-301XL + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 31.
V ehicle Hitch EXPLODED VIEW - AL-500 + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 32.
EXPLODED VIEW - AL-550 + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 33.
V ehicle Hitch 1 2 ASSEMBLY PAR TS ITE M QT Y P AR T NO. DESCRIPTIO N 12 9961K310 SHAFT COLLAR, 1-1/4" BORE 21 ALA03059 FOAM RUBBER GRIP 12in LONG 31 ALA050E C E-CLIP 41 ALA10010REV 2 ACUTAT OR 5.
ASSEMBLY PARTS ITE M QT Y P A R T NO. DESCRIPTIO N 1 12 H56033 SLIDERNUT, BRACKET - AL56 0 PLATFORM 24 H56040 BRACKET, SKIN - AL560 32 H56050 SKIN, PLATFO RM - AL560 44 H56060 BRACKET, WHE EL CRADDLE .
V ehicle Hitch HARMAR MOBILITY - 2075 47TH ST - SARASOT A, FL 34234 - 866.351.2776 - WWW.HARMAR.COM.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Harmar Mobility AL500 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Harmar Mobility AL500 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Harmar Mobility AL500, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Harmar Mobility AL500 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Harmar Mobility AL500, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Harmar Mobility AL500.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Harmar Mobility AL500. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Harmar Mobility AL500 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
