Manuel d'utilisation / d'entretien du produit 90 du fabricant Greenheck Fan
Aller à la page of 44
RECEIVING AND HANDLING The HRE is thoroughly inspected and test run at the factory. However, damage may occur during shipping and handling. Upon delivery, inspect the unit for both obvious and hidden damage. If damage is found, record all necessary information on the bill of lading and file a claim with the final carrier.
2 TABLE OF CONTENTS Storage and Basic Operation .............. 2 Installation .............................. 3 Lifting ................................. 3 Unit Weights & Recommended Roof Openings ............................ 3 Roof Curb Mounting .
3 INSTALLATION The system design and installation should follow accepted industry practice, such as described in the ASHRAE Handbook. Adequate space should be left around the unit for piping coils and drains, filter replacement, and maintenance.
4 Rooftop units require curbs to be mounted first. The duct connections must be located so they will be clear of structural members of the building. 1. Factory Supplied Roof Curbs Roof curbs are Model GKD, which are shipped in a knockdown kit (includes duct adapter) and require field assembly (by others).
5 1 Fan Wheel Dia. 1 Fan Wheel Dia. R o t a t i o n R o t a t i o n R o t a t i o n R o t a t i o n Length of Straight Duct GOOD POOR GOOD POOR GOOD POOR Tu rning V anes Tu rning V anes SYSTEM EFFECT F ACTOR CURVES FPM X 100 OUTLET VELOCITY 0 5 10 15 20 25 30 35 40 45 1.
6 ELECTRICAL INFORMATION The unitmust be electricallygrounded in accordancewith the currentNational Electrical Code,ANSI/NFPA No. 70.In Canada, usecurrent C.S.A. StandardC22.1, Canadian ElectricalCode, Part 1.
7 1. Main Disconnect (non-fusible, lockable) 2. Motor Starter - Exhaust Air Fan 3. Motor Starter - Outdoor Air Fan 4. Motor Contactor - Energy Wheel 5. 24 VAC Control Transformer 6. 24 VAC Terminal strip 7. Fuses for blower motors 8. Motor Contactor - Indirect Evap Pump 9.
8 Wheel Cassette 2 in. filters 2 in. filters Direct Evap Section Exhaust Air Intake Electrical Box Access Panel Access Panel Access Panel Access Panel Access Panel Cassette Slides Out 52 in. Clearance with IG Heater 0 in. Clearance without IG Heater Exhaust Hood Outdoor Air Hood IG Heater *48 in.
9 DIMENSIONAL DATA / ACCESS DOOR DESCRIPTIONS Following is a list of items accessible through the access doors shown on the diagram at the right. Some items are optional and may not have been provided.
10 1. After the energy recovery unit is set in place, run the overflow and drain lines to the exterior fittings on the evaporative cooler (drain & overflow connections at unit are 1-inch male pipe thread). The supply line can be attached at the downstream side of the evaporative cooler.
11 7. Verify that both airflow and system static pressure are in agreement with the specifications. If these conditions are met, check for water carry over from the discharge side of the media. If carry over is observed, check the distribution header for holes or tears and the water standoff tube for blockage.
12 Evaporative Timer Evaporative Freeze Protection t2 settings t1 settings Temperature Setting AUTO DRAIN AND FILL WITH FREEZE PROTECTION This system will automatically drain the sump tank and fill it with fresh water at the field adjustable intervals, typically once every 24 hours.
13 Cooling coilsare provided witha stainless steeldrain pan with3/4-in. female NPTdrain connection. Adrain trap must be connected to the drain connection to allow excess water to flow out of the drain pan.
14 DRAIN AND OVERFLOW CONNECTION LOCATIONS Model Connection Locations - in inches Outdoor Air Side Exhaust Side A B C D A B C D HRE-20 4.00 2.875 40.75 42.25 4.00 2.875 52.25 53.75 HRE-45 6.25 5.125 42.625 44.125 6.25 5.125 56.50 58.00 HRE-55 6.375 5.
15 Symptom Solution Leaving Air Entering Air 45 ° 15 ° Insufficient water volume or recirculation pump not operating Irregular water distribution on cooling media Scale and mineral deposit formation on face of media Excessive water discharge into drain Water Carry-Over Poor performance after cooling pad replacement Inadequate cooling A.
16 Regularly scheduled maintenance is the key to peak performance, minimized cost, and extended life of the evaporative cooler. The following is a checklist of items that need to be looked at on a regular basis. 1. The media should be checked for mineral and foreign material deposits that have built up.
17 Electric Heater Application/Operation Factory installed electric heaters can be provided for preheat and/or post-heat. An electric preheater warms the outdoor air prior to the energy recovery wheel to prevent frosting on the wheel. An electric post-heater warms the air leaving the energy recovery wheel to a user specified discharge temperature.
18 Frost Control Application/Operation Extremely cold outdoor air temperatures can cause moisture condensation and frosting on the energy recovery wheel. Frostcontrol is anoptional feature thatwill prevent/control wheelfrosting.
19 The energy recovery wheel operation can be altered to take advantage of economizer operation (free cooling). Two modesare available: 1)De-energizing the wheelor 2) Modulatingthe wheel. Afield supplied callfor cool (Y1) is required.
20 Variable Frequency Drives for Blowers Optional factory installed, wired, and programmed variable frequency drives (VFD) may have been provided for modulating or multi-speed control of the blowers. One VFD is provided for each blower (outdoor air and exhaust).
21 S1 toSN contactfor On/Off A1 (0-10VDC) referencedto AC (Canuse +15VDC from +V) Parameter Setting A1-01 Access Level 2 C6-02 Carrier frequency 2 d2-02.
22 FA CT ORY SUPPLIED AND WIRED G MUL TI-VOL TA GE PRIMARY 24 SECONDARY TR1 C FU5 TO UNIT MAIN POWER L3 L2 L1 DS1 SUPPL Y DAMPER D2 ENERGY WHEEL R1 R TR1 SO SR 3 FR FC 2-10V - + 1 TR 5 4 2 SR+ RETURN .
23 Rotation Sensor Dirty Filter Sensor The rotation sensor monitors energy recovery wheel rotation. If the wheel should stop rotating, the sensor will close a set of contacts in the unit control center.
24 Vapor Tight Lights Vapor tight lights provide light to each of the compartments in the energy recovery unit. The lights are wired to a switch mounted on the outside of the unit. The switch requires a separate power source to allow for power to the lights when the unit main disconnect is off for servicing.
25 OPTIONAL ACCESSORIES The remote panel is a series of junction boxes ganged together and includes a stainless steel face plate. The remote panel is available with a number of different alarm lights and switches to control the unit. The remote panel ships loose and requires mounting and wiring in the field.
26 W1 12 7 6 Y2 Y1 G C R NC C NC C NO NO Indicator Lights powered by the ER Unit Unit On/Off Frost Control Economizer Rotation Sensor Supply Dirty Filter Exhaust Dirty Filter PS2 PS3 NC NC NO C NO C Dirty Filter Indicator (Power by Others) Supply Dirty Filter Exhaust Dirty Filter PS2 PS3 Hot L1 Refer to Pressure Switch for voltage and load ratings.
27 A3 A3 W1 12 7 6 Y2 Y1 G C R Heating/Cooling Switches and Night Setback Switch/Timer Unit On/Off Heat Econ/First Stage Cooling Second Stage Cooling Night SetbackSwitch S1 S6 S7 S4 S5 Terminal .
28 OPTIONAL ACCESSORIES RAI RAF-P RA FIL TER OA AW COOL COIL ACC HEA T COIL OA F-A OA D SUPP LY BLOWER TO INSIDE FROM INSIDE EW-P OAW- P ENERGY WHEEL EA W EF-A OA I OA FIL TER OAF-P TO OUTSIDE FROM OU.
29 START-UP CHECKLIST FOR UNIT Unit ModelNumber ____________________________ (e.g. HRE-55) Unit Serial Number ____________________________ (e.
30 Line Voltage - check at unit disconnect L1-L2 ________ Volts L2-L3 ________ Volts L1-L3 _______ Volts Motor AmpDraw: Supply Motor Amps L1 ________ Amps L2 ________ Amps L3 ________ Amps Exhau.
31 Refer to the respective sections in this Installation, Operation and Maintenance Manual for detailed information. Refer to wiring diagram in unit control center to determine what electrical accessories were provided.
32 Fans (Forward Curved Type) The HRE Models contain a forward curved supply fan and a forward curved exhaust fan. These forward curved fans should be checked for free rotation. If any binding occurs, check for concealed damage and foreign objects in the fan housing.
33 Vibration Excessive vibration may be experienced during initial start-up. Left unchecked, excessive vibration can cause a multitude of problems, including structural and/or component failure. The most common sources of vibration are listed below. Many of these conditions can be discovered by careful observation.
34 UNIT START-UP Energy Recovery Wheel The HRE models contain a sensible energy recovery wheel. The wheels are inspected for proper mechanical operation at the factory. However, during shipping and handling, shifting can occur that may affect wheel operation.
35 Once the unit has been put into operation, a routine maintenance program should be set up to preserve reliability andperformance. Items tobe included inthis program ar.
36 ROUTINE MAINTENANCE Proper fan belt settings Belt Span Deflection = Belt Span 64 The proper belt setting is the lowest tension at which the belts will not slip under peak load operation. For initial tensioning, set the belt deflection at 1 / 64 -inch for each inch of belt span (measured half-way between sheave centers).
37 External Filter Maintenance Aluminum mesh, 2-inch deep filters are located in the supply weatherhood (if the weatherhood option was purchased). Filters should be checked and cleaned on a regular basis for best efficiency. The frequency of cleaning depends upon the cleanliness of the incoming air.
38 Access to wheel through outdoor air filter door The HRE units have one energy recovery wheel. Open the outdoor air filter door to access the wheel. For the HRE-20 and HRE-45 models, the wheel cassette slides out. Due to the size and weight of the HRE-55 and HRE-90 wheels, they remain stationary and all maintenance is performed in place.
39 CLEANING THE ENERGY RECOVERY WHEEL If the wheel appears excessively dirty, it should be cleaned to ensure maximum operating efficiency. Only excessive buildup of foreign material needs to be removed. DISCOLORATION AND STAINING OF ENERGY RECOVERY WHEEL DOES NOT AFFECT ITS PERFORMANCE.
40 PARTS LIST 1 2 3 4 8 5 6 7 7 9 Model HRE (shown with indirect evaporative cooler, optional direct evaporative cooler, and indirect gas heater) 10 1. Supply blower - Forward curved fan - Adjustable motor mount for belt tensioning - Adjustable sheaves for speed control 2.
41 The HRE units are pre-wired such that when a call for outside air is made (via field supplied 24 VAC control signal wired to unit control center), the supply fan, exhaust fan and energy wheel are energized and the motorized dampers open. The HRE units can be supplied with or without heating and cooling coils.
42 Test and Balance Report The test and balance report (TAB) is utilized to determine whether the appropriate amount of outdoor air and exhaust air is being supplied and removed from a building, respectively. There are no set rules on what information must be included in a TAB report.
43 * Always provide the unit model and serial number when requesting parts or service information. * Always check motor amps and compare to nameplate rating.
*Always provide the unit model and serial number when requesting parts or service information. *Always check motor amps and compare to nameplate rating. Energy Wheel Does NOTTurn Blower fan motor overloads are tripping and auto-resetting. Decrease fan speed.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Greenheck Fan 90 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Greenheck Fan 90 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Greenheck Fan 90, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Greenheck Fan 90 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Greenheck Fan 90, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Greenheck Fan 90.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Greenheck Fan 90. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Greenheck Fan 90 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
