Manuel d'utilisation / d'entretien du produit GN-AP101B du fabricant Gigabyte
Aller à la page of 39
GN - AP101B Wireless Access Point User Guide http://www.gigabyte.com.tw Rev.1.1.
Safety, Care and Regulatory Information Important safety in structions Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. l The product should be operated only from the type of power source indicated on the rating label.
controller (NIC) receptacle. • Disconnect the modem cable before opening a product enclosure, touching or installing internal components, or touching an uninsulated mod em cable or jack. • Do not use a telephone line to report a gas leak while you are in the vicinity of the leak.
FCC Radiation Exposure Statement This equ ipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) duri ng normal operation.
Contents 1. INTRODUCTION .................................................................................................... 1 1 - 1. C ONTENTS OF Y O UR S HIPMENT ........................................................................... 1 1 - 2. P HYSICAL I NTERFACE .
1 1. Introduction GN - AP101B access point makes wireless networking a pra ctical reality in more places, more companies and more environments than ever. Thanks to robust, secure, industry - standard 802.11b wireless networking, you can build networks that were previously far too expensive or too complex.
2 1 - 2. Physical Interface w One Ethernet LAN Port RJ - 45, Auto - sensing and Auto - MDI/MDIX for 10/100M Ethernet LAN connection w Init Button Initial reset (Init to factory default) w Wireless antenna One 2.4 GHz antenna - IEEE802.11b w Wireless solution Intersil Prism2.
3 1 - 4. Key features w Compatible with IEEE 802.11b Standard w Auto data rate for 11/5.5/2/1Mbps w 802.1D transparent Bridge w Operation Channels for US/Canada, ETSI, and Japan.
4 2. Installation Follow these steps to install the GN - AP101B Wireless Access Point. 1. Choose a proper place for GN - AP101B Wireless Access Point. In general, the best location is at the center of your wirel ess coverage area, within line of sight to all wireless devices.
5 There are two installation mode for your reference as follow ： Static IP address Method 1 If you are N ot using a DHCP server in your network, you can configure the AP by connecting to the computer directly. 1. Y ou will need to assign a Static IP Address t o the computer that you are using to configure the Access Point on the same subnet .
6 Method 2 If require to setup as many Access Points at the same time. You can setup a DHCP Server and let it assign IP to all the Access Points so it has its own unique IP address. After the setup is finished , and then remove or disabled DHCP Server at la st.
7 3. Access Point Manager The Gigabyte Access Point Manager is used to configure Gigabyte Access Points. Note: The performance of wire line link is bet ter than wireless link between the AP Manager and each Access Point. To use the wire line link to manage the Access Point is recommended.
8 Step3. Click “ Next ” . Step4. Type the User Information then click “ Next ” ..
9 Step5. Click “ Next ” t o accept the default directory or “ Browse ” to another location. Step6. Click “ Next ” ..
10 Step7. Click “ Next ” . Step8. Please wait a while..
11 Step9. Click “ Finish ” to complete setup..
12 3 - 2. Using the Access Point Manage r You can launch Gigabyte AP Manager through Start Programs Gigabyte AP Manager Utility Gigabyte AP Manager . Enter the default password “ admin ” and click “ OK ” . It will automatically search for Access Points on the same subnet when you open t he Gigabyte AP Manager.
13 n Tree structure ESSID (ap101b) AP Name (AP101B) MAC Address (0020ED001700) n Menu bar Tools Allow you to “ Sea rch ” for AP by ESSID, AP Name, MAC Address, and IP Address and “ Connect to AP by IP ” . And allow you to “ Save ” , “ Load ” the AP configuration and “ Copy ” , “ Paste ” the configuration at the current page.
14 n Tool bar Find Access Point Connect To AP By IP Save AP Configuration Load AP configuration Page Copy Page Paste System Reboot Load Default - Find Access Poi nt: Find all AP in the same subnet. - Save AP Configuration: Save all setting of the AP to a temp file.
15 System Page The System Page displays the Device_Information and the Change Community String function. n Device_Information The Device_Information includ e the AP name, MAC address, device description, the version information and the device type. You can change the AP Name to whatever unique name, which can represent this AP.
16 In case you forget the community string, you have to press the AP init button and then the AP setting (include community string) will be restore to default value. Note: The SNMP community string defines the relationship between an SNMP manager system (AP Manager) and the agent systems (all APs) .
17 IP Config Page n Obtain an IP address automatically You can check this selection to get IP address from the DHCP server automatically in you network. n Use the following IP address You can check this se lection to assign IP address by yourself. The default IP address is 192.
18 Wireless Operation Page Normally, you can have the wireless works smoothly even you didn ’ t change any item in this p age. n Region Because of the different region has a different open channel regulation , please check whether the default region value is your local area.
19 n Au to Rate In this item you can select either “ enable ” or “ disable ” . The default value is “ enable ” . Enable: If the selection is “ enable ” , the transfer rate will a utomatically change to the optimum rate allowed. The range of auto - change will base on the settin g of “ Transmit Rate ” .
20 Encryption Page This page is the security configuration of the wireless connection. WEP (Wired Equivalent Privacy) is a data privacy mechanism based on a 64/128 - bit shared key algorithm, as described in the IEEE 80 2.1 x standard. When the “ Disable ” is selected there is no WEP encryption .
21 802.1x authentication for wireless LANs provides centralized, server - based athentication of end users. 1) A client sends a “ start ” message to an access point, which requests the i dentity of the client.
22 n Automatic Generation Check this selection can allow user to generate the WEP key based on the string user key in. This filed can key i n up to 10 character. If the “ Automatic Generation ” is not checked user can manually change the WEP key by key in the HEX value.
23 Radius Page n Primary RA DIUS server Please assign a IP address to the primary RADIUS server( authentication server ). n Authentication Port The setting range is 1~65536 and the default value is 1812. n Authentication sercet This filed can key in up to 256 character.
24 Advanced Page For enhance the security of the wireles s network , this AP provide the MAC address filtering mechanism to prevent the unauthorized user access. Check “ Enable MAC filter ” and key in MAC address table, then only those MAC address in the table are allowed to connect to this AP.
25 OperationMode Page The Access Point supports three operation modes: “ Access Point ” , “ Point to Point ” , “ Poin t to MultiPoint ” . The default operation mode is “ Access Point ” . n Access Point Mode In this operation mode, the Access Point works as a Standard 802.
26 n Point To MultiPoint Mode In this WDS supported mode, the Access Point can communication with oth er GIGA - BYTE Access point which is also set to Point to Point and MultiPoint mode. Click the “ WDS List ” button, it will go to the WDS List page.
27 The maximum number of the connectible Access Point is 8. Click “ Scan ” button, the Scan Window will appear as below. You can select which Access Point you want or choose " Select All " check box, and then click “ OK ” to add those MAC Address into WDS List .
28 Associated List Page From this page, you will get the information of the workstation which can connect to the AP. The for m list includes the MAC Address, Signal level and description of the workstation.
29 Change AP Manager Password User can change the administration password of the AP manger to prevent other user access to the AP Manager. On the Menu Bar (Password - >AP Manage r Password) can invoke the password change dialog. Please enter a new admin password and confirm admin password then press “ OK ” .
30 4. Upgrade Firmware You can download the upgraded firmware version from Gigabyte website. n Run TFTP Program Step1. You can find the “ Upgrade Tool ” through Start Programs Gigabyte AP Manager Utility Gigabyte AP Upgrade . Step2. The Gigabyte Firmware Upgrade Tool screen will appear.
31 Step3. Press “ Open ” button to choose the firmware then press “ U pgrade ” button to start the firmware upgrade process. Note: During the firmware upgrade, please DO NOT turn off the PC or AP and DO NOT unplug the Ethernet cable. Step4. After the AP device rebooting successful, the AP firmware upgrade is co mpleted.
32 5. Uninstall AP Manager Utility You can find the Uninstall program thr ough Start Programs Gigabyte AP Manager Utility Uninstall . Step1. The InstallShield Wizard will appear then please wait. Step2. Click “ Yes ” . Step3. Click “ OK ” and then the Gigabyte AP Manager Utility has been uninstalled successfully .
33 If y ou just want to modify some program components or reinstall all program components, you can run the installation program directly. And then the InstallShield Wizard will appear. Please choose one of the options what you want then click “ Next ” continues to modify, repair or remove the Gigabyte AP Manager Utility.
34 Limited Warranty 1 - Year Warranty Gigabyte warrants to the original consumer/purchaser that the product free from defects in material and workmanship for no limited time from the original manufa ctory shipment date . This warranty does not cover the product if it is damaged in the process of being installed or improperly used.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Gigabyte GN-AP101B c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Gigabyte GN-AP101B - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Gigabyte GN-AP101B, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Gigabyte GN-AP101B va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Gigabyte GN-AP101B, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Gigabyte GN-AP101B.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Gigabyte GN-AP101B. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Gigabyte GN-AP101B ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
