Manuel d'utilisation / d'entretien du produit ZIFS36N LH du fabricant GE
Aller à la page of 20
GE Monogram ® Installation Instructions Stainless Steel 36" Built-In Refrigerators and Freezers Models ZIRS36N LH – All Refrigerator ZIRS36N RH – All Refrigerator ZIFS36N LH – All Freezer ZIFS36N RH – All Freezer www.
2 Before you begin – Read these instructions completely and carefully. IMPORT ANT – Save these instructions for local inspector’ s use. IMPORT ANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer – Be sure to leave these instructions with the Consumer .
3 Design Information 36" Stainless Steel Refrigerators, Freezers Flush or Semi-Flush Enclosure Installations T rue Flush Installation In a flush installation, the refrigerator door will align evenly with the front face of adjacent cabinet doors. The refrigerator blends into the surrounding cabinetry .
4 Design Information 36" Stainless Steel Refrigerators, Freezers Side By Side Installation Of Freezer And Refrigerator For a complete food storage center , install a Monogram Freezer and Refrigerator side by side. For even more capacity , install two refrigerators and one or two freezers.
5 Design Information 36" Stainless Steel Refrigerators, Freezers Installation At End-of-Run Frameless Cabinets NOTE: 1/2" thick side panels shown. Side panels can be any thickness. Add side panel thickness to outside trim width, (36” or 72" for two models) to calculate the rough-in dimension.
6 Installation Preparation 36" Stainless Steel Refrigerators, Freezers Electrical and Water Connection Locations The water line can be routed through the floor or back wall. • The icemaker water line should be: – Approximately 3-1/2" from the floor on the back wall, or 3-1/2" from the back wall on the floor .
7 Installation Preparation 36" Stainless Steel Refrigerators, Freezers Grounding the Refrigerator IMPORT ANT – (Please read carefully) FOR PERSONAL SAFETY , THIS APPLIANCE MUST BE PROPERL Y GROUNDED.
8 Installation Preparation 36" Stainless Steel Refrigerators, Freezers T ools Required • T insnips to cut banding • Stepladder • Bucket • Level • 1-1/4" open-end wrench • Applian.
9 Installation 36" Stainless Steel Refrigerators, Freezers • A cold water supply is required for automatic icemaker operation. The water pressure must be between 20 and 120 p.s.i. • Route 1/4" OD copper or GE SmartConnect ™ tubing between house cold water line and the water connection location.
10 Installation 36" Stainless Steel Refrigerators, Freezers • Side panels are required whenever the sides of the product will be exposed and when installed between frameless cabinets. See pages 3 and 4. • Side panels are not required when installed into an enclosure.
11 Installation 36" Stainless Steel Refrigerators, Freezers Step 5 Level Refrigerator These products have a 4-point leveling system. The front is supported by leveling legs, the rear is supported by wheels. • Adjust rear wheels beneath the product to just barely touch the 2x4 block.
12 Installation 36" Stainless Steel Refrigerators, Freezers Step 8 Check Power Step 9 Mount T op Grille Panel For shipping purposes, the top case trim is secured at 84" installation height.
13 Installation 36" Stainless Steel Refrigerators, Freezers Step 11 Install T oekick • A standard toekick is supplied. Install with 2 screws provided, adjust to desired height and tighten screws. IMPORTANT: The vented toekick must remain unobstructed for proper air circulation and operation.
14 ZUGSS T rim Kit Unified Stainless Steel Custom Grille Panel T ools and Materials Required: • #1 and #2 Phillips screwdrivers or sockets • 1/4" angled wrench and 1-1/2" open ended wrench • Drill and appropriate bits • Custom grille panel • Safety glasses • Gloves to protect against sharp edges Parts List: A.
15 • Cut a 2"x4" block, 71" long. Secure the 2"x4" to the 4 mounting brackets provided using #12 or #14 wood screws. • Secure the brackets with wood block to the back wall so that it is 84" (or your installation height) from the finished floor .
16 ZUGSS T rim Kit Unified Stainless Steel Grille Panel Step 5 Install Center T rim Strip • Open doors fully . • Starting at the top, press trim strip over inside case trims of both products. • Continue pressing trim until you reach the bottom of the case trims.
17 ZUGSS T rim Kit Unified Stainless Steel Grille Panel Step 7 Install Grille Base Cover • Open doors fully . • Install the double width grille base cover by slipping the notched ends over the hinges. • Place wire fence over the grille base cover (textured side out).
18 ZUGSS T rim Kit Unified Stainless Steel Grille Panel Step 9 Install Soffit V ent T op • Separate the top and hinge side trim pieces by removing side screws. Discard top piece; retain screws. • Install one end piece to unified top piece with 2 original screws.
19 ZUGSS T rim Kit Unified Stainless Steel Grille Panel Step 11 Adjust Door Alignment Check door alignment. The top of the door should be parallel with the grille panel. If the door appears to be too high or too low on the handle side, adjustments can be made.
Pub. No. 49-60073-3 Part No. 197D3003P001 12-03 JR 65161-01 Note: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local service in your area, call 1.800.444.1845. Note: Product improvement is a continuing endeavor at General Electric.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté GE ZIFS36N LH c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du GE ZIFS36N LH - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation GE ZIFS36N LH, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le GE ZIFS36N LH va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le GE ZIFS36N LH, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du GE ZIFS36N LH.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le GE ZIFS36N LH. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei GE ZIFS36N LH ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
