Manuel d'utilisation / d'entretien du produit AS-250 du fabricant Alto-Shaam
Aller à la page of 24
MN-28860 • 01/11 printed i n u . s . a . Cooking & Holding Oven Electric Manual Control M odel : AS-250 •INSTALLATION •OPERATION •MAINTENANCE W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA PHONE: 262.
Delivery ...................................... 1 Unpacking .................................... 1 Safety Procedures and Precautions ................. 2 Installation Installation Requirements ...................... 3 Clearance Requirements ...........
AS-250 inStAllAtion / operAtion / Service mAnuAl p g . 1 DELIVERY This Alto-Shaam appliance has been thoroughly tested and inspected to ensure only the highest quality unit is provided. Upon receipt, check for any possible shipping damage and report it at once to the delivering carrier.
p g . 2 AS-250 inStAllAtion / operAtion / Service mAnuAl CAUTION Used to indicate the presence of a hazard that can or will cause minor personal injury, property damage, or a potential unsafe practice if the warning included with this symbol is ignored.
AS-250 inStAllAtion / operAtion / Service mAnuAl p g . 3 SITE INSTALLATION The Alto-Shaam cook and hold oven must be installed in a location that will permit the oven to function for its intended purpose and to allow adequate clearance for ventilation, proper cleaning, and maintenance access.
p g . 4 AS-250 inStAllAtion / operAtion / Service mAnuAl SITE INSTALLATION 33-9/16" (853mm ) 5-1/2" (140mm) 17-1/4" (438mm) 16-3/4" (425mm) 40-1/8" (1019mm) Electrical Connection 7" (178mm) from top INSTALLATION AND START-UP A number of adjustments are associated with initial installation and start-up.
AS-250 inStAllAtion / operAtion / Service mAnuAl p g . 5 SITE INSTALLATION INSTALLATION LEG INSTALLATION INSTRUCTIONS Bottom V iew Item Description Part No. Qty 1 Legs 11547 2 2 Nylon Screws SC-2464 4 1. Attach legs a to bottom of unit using four (4) nylon screws b .
p g . 6 AS-250 inStAllAtion / operAtion / Service mAnuAl The appliance must be installed by a qualified service technician. The oven must be properly grounded in accordance with the National Electrical Code and applicable local codes.
AS-250 inStAllAtion / operAtion / Service mAnuAl p g . 7 CAUTION METAL PARTS OF THIS EQUIPMENT BECOME EXTREMELY HOT WHEN IN OPERATION. TO AVOID BURNS, ALWAYS USE HAND PROTECTION WHEN OPERATING THIS APPLIANCE. DANGER AT NO TIME SHOULD THE INTERIOR OR EXTERIOR BE STEAM CLEANED, HOSED DOWN, OR FLOODED WITH WATER OR LIQUID SOLUTION OF ANY KIND.
p g . 8 AS-250 inStAllAtion / operAtion / Service mAnuAl START BUTTON A fter all required settings have been entered, START begins the cooking-holding sequence. PROBE BUTTON U sed for setting probe cut-off temperature or recalling and checking previously set probe cut-off temperature.
AS-250 inStAllAtion / operAtion / Service mAnuAl p g . 9 OPERATING INSTRUCTIONS To stop an operation at any time — Press and hold the s tart Key until the control beeps for two seconds, indicating the operation has been cancelled. The oven will remain in a power-on state.
p g . 10 AS-250 inStAllAtion / operAtion / Service mAnuAl CAUTION TO MAINTAIN SAFE TEMPERATURE LEVELS, COLD FOOD FOR RETHERMALIZATION OR REHEATING MUST NEVER BE ADDED TO THE OVEN WHILE HOT FOODS ARE BEING HELD. Cook/Hold Instructions Press and release control O n / O ff key.
AS-250 inStAllAtion / operAtion / Service mAnuAl p g . 11 OPERATING INSTRUCTIONS Programming a Preset Select the product to be programmed and begin programming with the oven control power O f f .
p g . 12 AS-250 inStAllAtion / operAtion / Service mAnuAl OPERATING INSTRUCTIONS General Holding Guideline Chefs, cooks and other specialized food service personnel employ varied methods of cooking.
AS-250 inStAllAtion / operAtion / Service mAnuAl p g . 13 CARE AND CLEANING PROTECTING STAINLESS STEEL SURFACES It is important to guard against corrosion in the care of stainless steel surfaces. Harsh, corrosive, or inappropriate chemicals can completely destroy the protective surface layer of stainless steel.
p g . 14 AS-250 inStAllAtion / operAtion / Service mAnuAl EQUIPM E NT CARE Under normal circumstances, this oven should provide you with long and trouble free service. There is no preventative maintenance required, however, the following Equipment Care Guide will maximize the potential life and trouble free operation of this oven.
AS-250 inStAllAtion / operAtion / Service mAnuAl p g . 15 Food flavor and aroma are usually so closely related that it is difficult, if not impossible, to separate them. There is also an important, inseparable relationship between cleanliness and food flavor.
p g . 16 AS-250 inStAllAtion / operAtion / Service mAnuAl TROUBLE SHOOTING SERVICE Error Code Description Possible Cause E-10 Cavity air sensor shorted Cavity air sensor reading < 5°F. Verify sensor integrity. See sensor test instructions below. E-11 Cavity air sensor open Cavity air sensor reading > 517°F.
AS-250 inStAllAtion / operAtion / Service mAnuAl p g . 17 A. No power. Display will not light. 1. Verify that power is available at the outlet or junction box. 2. Verify that the circuit breaker switch on the back of the unit is turned on. 3. Verify that the power cord is not open.
p g . 18 AS-250 inStAllAtion / operAtion / Service mAnuAl AS-250 - EXTERIOR SERVICE VIEW SERVICE.
AS-250 inStAllAtion / operAtion / Service mAnuAl p g . 19 DANGER DISCONNECT UNIT FROM POWER SOURCE BEFORE CLEANING OR SERVICING. MODEL > AS-250 ITEM DESCRIPTION PART NO. QTY ITEM DESCRIPTION PART NO. QTY 1 TOP 1820 1 SENSOR SUPPORT BRACKET BK-2758 1 2 TOP MOUNTING SCREWS SC-2425 5 MOUNTING SCREWS SC-2064 1 3 TUBE ASSB.
p g . 20 AS-250 inStAllAtion / operAtion / Service mAnuAl.
AS-250 inStAllAtion / operAtion / Service mAnuAl p g . 21.
TRANSPORTATION DAMAGE and CLAIMS All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the carrier, such shipments become the property of the consignee. Should damage occur in shipment, it is a matter between the carrier and the consignee.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Alto-Shaam AS-250 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Alto-Shaam AS-250 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Alto-Shaam AS-250, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Alto-Shaam AS-250 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Alto-Shaam AS-250, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Alto-Shaam AS-250.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Alto-Shaam AS-250. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Alto-Shaam AS-250 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
