Manuel d'utilisation / d'entretien du produit Ranger (2011) du fabricant Ford
Aller à la page of 303
Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 16 Entertainment Systems 19 AM/FM stereo 19 AM/FM Stereo single CD/MP3 system 21 Auxiliary input jack (Line in) 26 Satellite r.
Seating and Safety Restraints 63 Seating 63 Safety restraints 69 Airbags 84 Child restraints 95 Tires, Wheels and Loading 1 12 T ire information 114 T ire inflation 117 T ire Pressure Monitoring Syste.
Maintenance and Specifications 225 Engine compartment 227 Engine oil 230 Battery 234 Engine coolant 237 Fuel information 242 Air filter(s) 258 Part numbers 262 Maintenance product specifications and c.
CONGRA TULA TIONS Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.
W arning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment W e must all play our part in protecting the environment.
Do not add friction modifier compounds or special break-in oils since these additives may prevent piston ring seating. See Engine oil in the Maintenance and Specifications chapter for more information on oil usage.
DA T A RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems.
limitations regarding 911 Assist and T raffic, directions and Information privacy below). However , parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.
CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers must not compromise their own or others’ safety when using such equipment.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emper.
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the service engine soon indicator to come on. It may take a long period of time for the system to detect an improperly installed or properly re-installed fuel filler cap depending on driving and fuel tank level conditions.
Airbag readiness: If this light fails to illuminate when the ignition is turned to on, continues to flash or remains on, contact your authorized dealer as soon as possible. A chime will sound when there is a malfunction in the indicator light. Safety belt: Reminds you to fasten your safety belt.
W ARNING: Never remove the coolant reservoir cap while the engine is running or hot. AdvanceT rac 威 /traction control: Illuminates when the AdvanceT rac 威 /traction control is active. If the light remains on, contact your authorized dealer as soon as possible.
Anti-theft system: Flashes when the SecuriLock 威 passive anti-theft system has been activated. Speed control (if equipped): Illuminates when the speed control is engaged. T urns off when the speed control system is disengaged. T urn signal: Illuminates when the left or right turn signal or the hazard lights are turned on.
Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating.
T achometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the on position).
AUDIO SYSTEMS AM/FM stereo (if equipped) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road.
3. AM/FM: Press to choose a frequency band in radio mode. 4. Memory preset buttons: T o set a station: Select frequency band AM/FM1/FM2; tune to a station, press and hold a preset button until sound returns. 5. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels.
AM/FM stereo single CD/MP3 satellite compatible system (if equipped) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road.
MENU to adjust the hours/minutes. Press CLK to display the time when the ignition is off. 3. MUTE: Press to mute the playing media. Press again to return to the playing media. 4. MENU: Press MENU repeatedly to scroll through the following modes and use MENU to make an adjustment in those modes.
saved songs. When the song title appears in the display that you would like to delete, press SEEK or preset #6. The song will appear in the display for confirmation. Press SEEK or preset #6 again and the display will read SONG DELETED. If you do not want to delete the currently listed song, press MENU to select either RETURN or CANCEL.
Next/previous directory: In MP3 mode, press MENU to go to the previous/next directory . Flat file/directory mode: In MP3 mode, use MENU to select flat file mode or directory mode. Normal / T rack title / File name: Use / to scroll through MP3 display options (track #, normal music name or file name).
11. SEEK/TRACK: Press to access the previous/next ( / ) strong station. In CD/MP3 mode, press to advance to the previous/next ( / ) track. In satellite radio mode (if equipped), press SEEK to seek to the previous/next channel. In CA TEGOR Y MODE, press SEEK to select a channel within that category .
15. ON/OFF/V olume: Press to turn on/off. T urn to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Required equipment: 1. Any portable music player designed to be used with headphones 2. An audio extension cable with stereo male 1/8 in. (3.5 mm) connectors at each end T o play your portable music player using the auxiliary input jack: 1. Begin with the vehicle parked and the radio turned off.
5. For safety reasons, connecting or adjusting the settings on your portable music player should not be attempted while the vehicle is moving. Also, the portable music player should be stored in a secure location, such as the center console or the glove box, when the vehicle is in motion.
• W ipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only .
Operating your audio system with MP3-formatted discs Y our MP3 system recognizes MP3 discs upon insertion and provides you with two ways to listen to these discs: • Flat file mode– This mode ignores any folders on the discs and plays all MP3 files found in any folder on the disc exactly as if there were no folders on the disc.
• MP3 flat file mode ignores any folder structure on the MP3 disc. The player numbers each MP3 track on the disc (noted by the .mp3 file extension) from T001 to a maximum of T255. Note: The maximum number of playable MP3 files may be less depending on the structure of the CD and exact model of radio present.
Satellite radio information (if equipped) Satellite radio channels: SIRIUS 威 broadcasts a variety of music, news, sports, weather , traffic and entertainment satellite radio channels. For more information and a complete list of SIRIUS 威 satellite radio channels, visit www .
Satellite radio electronic serial number (ESN): This 12–digit Satellite Serial Number is needed to activate, modify or track your satellite radio account.
Radio Display Condition Action Required NO TEXT Artist information not available. Artist information not available at this time on this channel. The system is working properly . NO TEXT Song title information not available. Song title information not available at this time on this channel.
HEA TER ONL Y SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle.
T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to the highest setting.
• Under normal weather conditions, do not leave the air flow selector in MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” using the outside air inlet vents. • Do not put objects under the front seats that will interfere with the airflow to the back seats.
HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the low beam headlamps on. Fog lamp control (if equipped) The fog lamps can be turned on when the headlamp control is in the or position and the high beams are not turned on.
Flash-to-pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) The daytime running light system turns the headlamps on with a reduced light output. T o activate: • the ignition must be in the on position and • the headlamp system is in the off position or parking lamp position.
Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer switch requires re-calibration. Rotate the dimmer switch from the full dim position to the full dome/on position to reset. This will ensure that your displays are visible under all lighting conditions.
3. T urn on the low beam headlamps and open the hood. 4. Locate the high intensity area of the beam pattern and place the top edge of the intensity zone even with the horizontal reference line (4). If the top edge of the high intensity area is not even with the horizontal line, follow the next step to adjust it.
TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Courtesy/reading lamps (if equipped) The courtesy lamp lights when: • any door is opened. • the instrument panel dimmer switch is held up until the courtesy lamps come on.
Examples of unacceptable moisture (usually caused by a lamp water leak) are: • W ater puddle inside the lamp • Large water droplets, drip marks or streaks present on the interior of the lens T ake your vehicle to a dealer for service if any of the above conditions of unacceptable moisture are present.
Replacing exterior bulbs Check the operation of all the bulbs frequently . Replacing headlamp bulbs/front park bulbs/turn signal bulbs T o remove the bulb(s): 1.
W ARNING: Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. Install the new bulb(s) in reverse order .
4. Rotate bulb socket counterclockwise and remove from lamp assembly . 5. Carefully pull bulb straight out of socket and push in the new bulb. 6. Install the bulb socket in lamp assembly by turning clockwise. Install the new bulb in reverse order . Replacing tail lamp/backup lamp bulbs 1.
3. Rotate bulb socket counterclockwise turn and remove from lamp assembly . 4. Carefully pull the bulb straight out of the socket. Install the new bulb(s) in reverse order . Replacing fog lamp bulbs (if equipped) 1. Make sure the headlamp switch is in the off position and remove the bulb socket from the fog lamp by turning it counterclockwise.
Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the off position and reach behind the rear bumper to locate the bulb socket. 2. T wist the socket counterclockwise and remove. 3. Carefully pull the bulb straight out of the socket.
MUL TI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Press the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid.
TIL T STEERING WHEEL (IF EQUIPPED) T o adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control.
Do not use the power point for operating the cigarette lighter element (if equipped). Note: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty , and can result in fire or serious injury .
One-touch down Allows the driver’ s window to open fully without holding the control down. Press the switch completely down to the second detent and release quickly . The window will open fully . Momentarily press the switch to any position to stop the window operation.
SPEED CONTROL (IF EQUIPPED) W ith speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal. W ARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Using speed control The speed controls are located on the steering wheel.
Disengaging speed control T o disengage the speed control, press the brake pedal or the clutch pedal (if equipped). Disengaging the speed control will not erase the previous set speed. Note: When you use the clutch pedal to disengage the speed control, the engine speed may briefly increase, this is normal.
POSITIVE RETENTION FLOOR MA T (IF EQUIPPED) W ARNING: Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the brake pedals. Position the floor mat so that the eyelets are over the retention posts and press down to lock in.
KEYS The key operates all locks on your vehicle. Y ou should always carry a second key with you in a safe place in case you require it in an emergency . If your vehicle is equipped with the SecuriLock 威 passive anti-theft system, your keys are coded to your vehicle; using a non-coded key will not permit your vehicle to start.
Y our vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors without a key . • lock all the vehicle doors without a key .
Note: The panic alarm will only operate when the ignition is in the off position. Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. T o replace the battery: 1. T wist a thin coin between the two halves of the remote entry transmitter near the key ring.
How to reprogram your remote entry transmitters Y ou must have all remote entry transmitters (maximum of four) available before beginning this procedure. Note: Ensure the brake pedal is not pressed during this sequence. T o reprogram the remote entry transmitters: 1.
The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps after several minutes if they are left on accidentally .
Anti-theft indicator The anti-theft indicator is located in the instrument cluster . V ehicles equipped with the SecuriLock 威 passive anti-theft system behave as follows: • When the ignition is in.
1. Insert a previously programmed coded key into the ignition. 2. T urn the ignition from the 2 (lock) position to the 4 (on) position. Keep the ignition in the 4 (on) position for at least one second, but no more than 10 seconds. 3. T urn the ignition to the 2 (lock) position, and remove the coded key from the ignition.
FRONT SEA TS W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
The adjustable head restraints consist of: • a trimmed energy absorbing foam and structure (1), • two steel stems (2), • a guide sleeve adjust/release button (3), • and a guide sleeve unlock/remove button (4). T o adjust the head restraint, do the following: 1.
W ARNING: The adjustable head restraint is a safety device. Whenever possible it should be installed and properly adjusted when the seat is occupied. T o remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position.
Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head. For occupants of extremely tall stature, adjust the head restraint to its full up position.
Lift the release bar to move seat forward or backward. Ensure that the seat is locked into place. Pull lever located at the side of the seat cushion up to adjust seatback. 60/40 seat (if equipped) T o gain access to the storage compartment in your armrest (if equipped), lift the latch to open lid.
Passenger side rear access Pull up on the recliner handle. The seat will lean forward. Lift the release bar to move the seat forward to access the rear area of the cab. T o return seat to original position, slide the seat bottom back, then push the seatback up to lock it in place.
W ARNING: Booster seats must be installed only in seating positions equipped with a combination lap/shoulder belt. SAFETY RESTRAINTS Personal Safety System™ The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries.
accident conditions (crash severity , belt usage, etc.) were not appropriate to activate these safety devices. Front airbags are designed to activate only in frontal and near -frontal collisions, not rollovers, side-impacts, or rear -impacts unless the collision causes sufficient longitudinal deceleration.
W ARNING: Airbags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
Determining if the Personal Safety System is operational The Personal Safety System uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the W arning lights and chimes section in the Instrument Cluster chapter .
W ARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
2. T o unfasten, press the release button and remove the tongue from the buckle. Restraint of pregnant women W ARNING: Always ride and drive with your seatback upright and the safety belt properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips.
Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T o lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. T o tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips.
When to use the automatic locking mode This mode should be used any time a child safety seat, except a booster , is installed in passenger front or rear seating positions. Children 12 years old and under should be properly restrained in a rear seating position whenever possible.
Energy management feature • This vehicle has a safety belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision. • This energy management system has a retractor assembly that is designed to pay out webbing in a controlled manner .
Front safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver and front outboard passenger . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder .
Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the on position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.
If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on... The Belt-Minder 威 feature will not activate.
The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers.
Reasons given... Consider ... “I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likely to DIE.
The driver and front passenger Belt-Minder 威 features can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set.
AIRBAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) The airbag supplemental restraint system is designed to work in conjunction with the safety belts to help protect the driver and front outboard passenger from certain upper body injuries. The term “supplemental restraint” means the airbags are intended as a supplement to the safety belts.
Airbags DO NOT inflate slowly or gently and the risk of injury from a deploying airbag is greatest close to the trim covering the airbag module. W ARNING: Rear facing child seats should NEVER be placed in front of an active airbag.
W ARNING: Do not attempt to service, repair , or modify the Airbag Supplemental Restraint System or its fuses. Contact your authorized dealer as soon as possible. W ARNING: The front passenger airbag is not designed to offer protection to an occupant in the center front seating position.
W ARNING: Front seating positions only: If seating two adults and a child, Ford recommends properly restraining the child in the center front seating position, but only if doing so will not interfere with driving the vehicle.
The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.
The front passenger sensing system is designed to meet the regulatory requirements of Federal Motor V ehicle Safety Standard (FMVSS) 208 and is designed to turn off the front passenger’ s frontal ai.
The front passenger sensing system is designed to enable (may inflate) the right front passenger’ s frontal airbag anytime the system senses that a person of adult size is sitting properly in the front passenger seat.
In case there is a problem with the passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. Do NOT attempt to repair or service the system; take your vehicle immediately to the dealer . W ARNING: The front passenger airbag is not designed to offer protection to an occupant in the center seating position.
Determining if the system is operational The SRS uses readiness lights in the instrument cluster or a tone to indicate the condition of the system. Refer to Airbag readiness in the Instrument Cluster chapter . Routine maintenance of the airbag is not required.
W ARNING: All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided. How does the side airbag system work? The design and development of the side airbag sy.
W ARNING: Several airbag system components get hot after inflation. Do not touch them after inflation. W ARNING: If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer .
SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags.
Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Infants or toddlers Children weighing 40 lb (18 kg) or less (generally age four or younger) Use a child safety seat (sometimes called an infant carrier , convertible seat, or toddler seat).
Recommendations for attaching child safety restraints for children Restraint T ype Child W eight Use any attachment method as indicated below by “X” LA TCH (lower anchors and top tether anchor) LA.
W ARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury or death. W ARNING: Never use pillows, books, or towels to boost a child.
Follow all the safety restraint and airbag precautions that apply to adult passengers in your vehicle. If the child is the proper height, age, and weight (as specified by your child safety seat or boo.
position whenever possible. If all children cannot be seated and restrained properly in a rear seating position, properly restrain the largest child in the front seat. When installing a child safety seat with combination lap/shoulder belts: • Use the correct safety belt buckle for that seating position.
W ARNING: Rear facing child seats should NEVER be placed in front of an active airbag. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
10. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. T o check this, grab the seat at the belt path and attempt to move it side to side and forward. There should be no more than 1 inch (2.
Attaching child safety seats with LA TCH (Lower Anchors and T ethers for CHildren) attachments The LA TCH system is composed of three vehicle anchor points: two (2) lower anchors located where the vehicle seat back and seat cushion meet (called the “seat bight”) and one (1) top tether anchor located behind that seating position.
• 60/40 seats Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor . Once the child safety seat has been installed using the safety belt, you can attach the top tether strap.
The tether anchor is located on the rear lower portion of the passenger seat. 3. Clip the tether strap to the anchor . If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision.
Center seating location When installing a child safety seat in the front center position, route the tether strap over the center arm rest and clip it to the center anchor . If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision.
Keep your child in the child safety seat if it properly fits the child, remains appropriate for their weight, height and age AND if properly secured to the vehicle.
• Can the child stay seated like this for the whole trip? T ypes of booster seats There are generally two types of belt-positioning booster seats: backless and high back. Always use booster seats in conjunction with the vehicle lap/shoulder belt. • Backless booster seats If your backless booster seat has a removable shield, remove the shield.
Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision.
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road.
Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on transfer case operation and shifting procedures can be found in the Driving chapter .
• Narrower – to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUVs and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition.
T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100.
TIRES T ires are designed to give many thousands of miles of service, but they must be maintained in order to get the maximum benefit from them. Glossary of tire terminology • T ire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry .
INFLA TING YOUR TIRES Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required.
The cold inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label or T ire Label. When weather temperature changes occur , tire inflation pressures also change. A 10°F (6°C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure.
TIRE CARE Inspecting your tires and wheel valve stems Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves.
W ARNING: Age T ires degrade over time depending on many factors such as weather , storage conditions, and conditions of use (load, speed, inflation pressure, etc.) the tires experience throughout their lives. In general, tires should be replaced after six years regardless of tread wear .
W ARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Ford.
It is recommended that the two front tires or two rear tires generally be replaced as a pair . The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels.
Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment.
INFORMA TION CONT AINED ON THE TIRE SIDEW ALL Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.
7. H: Indicates the tire’ s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure.
10. T ire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber -coated fabric in the tire tread and sidewall. T ire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester , and others.
Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below . Note: T ire Quality Grades do not apply to this type of tire.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Understanding your tire pressure monitoring system (TPMS) The tire pressure monitoring system measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The low tire pressure warning light will turn on if the tire pressure is significantly low .
When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn you when your tires need air .
Low tire pressure warning light Possible cause Customer action required Flashing warning light Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality .
SNOW TIRES AND CHAINS W ARNING: Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. W ARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford.
your vehicle, familiarize yourself with the following terms for determining your vehicle’ s weight ratings, with or without a trailer , from the vehicle’ s T ire Label or Safety Compliance Certification Label: Base Curb W eight – is the weight of the vehicle including a full tank of fuel and all standard equipment.
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight.
GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear).
• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury .
GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage.
W ARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lb.
to transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440 - 1200 = - 240 lb.
Follow these guidelines to ensure safe towing: • Do not tow a trailer until your vehicle has been driven at least 1,000 miles (1,600 km). • Consult your local motor vehicle laws for towing a trailer . • Refer to the instructions included with towing accessories for the proper installation and adjustment specifications.
SuperCab 4x2 Powertrain Maximum GCWR - lb (kg) Maximum T railer W eight - lb (kg) 2–Door Payload Package 1 without Jump Seat 2.3L w/manual transmission 4800 (2177) 1380 (626) 2.3L w/automatic transmission 5500 (2495) 2040 (925) 4.0L w/manual transmission 7000 (3175) 3360 (1524) 4.
SuperCab 4x2 Powertrain Maximum GCWR - lb (kg) Maximum T railer W eight - lb (kg) 4–Door Payload Package 2 with Jump Seat 4.0L w/manual transmission 7000 (3175) 3240 (1470) 4.
SuperCab 4x4 Powertrain Maximum GCWR - lb (kg) Maximum T railer W eight - lb (kg) 4–Door with Jump Seat 4.0L w/manual transmission 7000 (3175) 3000 (1361) 4.0L w/automatic transmission 9500 (4309) 5460 (2477) Notes: • For high altitude operation, reduce GCW by 2% per 1,000 ft.
Color Function Comment 3. T an/White T ail lamp Relay-controlled circuit activated when the park lamps/headlamps are on. 4. White Ground Matching vehicle circuit returns to battery’ s negative ground. Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle.
Safety chains Always connect the trailer’ s safety chains to the frame or hook retainers of the vehicle hitch. T o connect the trailer’ s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer , follow the instructions that the rental agency gives to you.
• Under extreme conditions with large frontal trailers, high outside temperatures and highway speeds, the coolant gauge may indicate higher than normal coolant temperatures. If this occurs, reduce speed until the coolant temperature returns to the normal range.
Exceeding these limits may allow water to enter vehicle components: • Causing internal damage to the components. • Affecting driveability , emissions and reliability . Replace the rear axle lubricant any time the axle has been submerged in water .
2WD vehicles equipped with an automatic transmissions: Do not tow your vehicle with any wheels on the ground, as vehicle or transmission damage may occur . It is recommended to tow your vehicle with all four (4) wheels off the ground such as when using a car -hauling trailer .
ST ARTING Positions of the ignition 1. Accessory — allows the electrical accessories such as the radio to operate while the engine is not running. 2.
W ARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine.
If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Press and hold the clutch pedal to the floor , then put the gearshift lever in the N (Neutral) position. 3. T urn the key to 4 (on) without turning the key to 5 (start).
1. T urn the key to 4 (on) without turning the key to 5 (start). If there is difficulty in turning the key , rotate the steering wheel until the key turns freely . This condition may occur when: • the front wheels are turned, or • a front wheel is against the curb.
W ARNING: Failure to follow engine block heater instructions could result in property damage or physical injury . W ARNING: T o reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters.
• Finally , have the engine block heater system checked during your fall tune-up to be sure it’ s in good working order . How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. T o clean them, use a dry cloth.
has continuous vibration or shudder in the steering wheel while braking, the vehicle should be inspected by an authorized dealer . The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency . The wheels are prevented from locking even when the brakes are firmly applied.
Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned on) until the parking brake is released.
ADV ANCETRAC 姞 WITH ROLL ST ABILITY CONTROL™ (RSC 姞 ) ST ABILITY ENHANCEMENT SYSTEM Y our vehicle is equipped with the AdvanceT rac 威 with RSC 威 system.
W ARNING: If a failure has been detected within the AdvanceT rac 威 with RSC 威 system, the stability control light will illuminate steadily and you may hear a chime. If equipped with a message center , the vehicle will also indicate a failure with the brake system, have the system serviced by an authorized dealer immediately .
T raction control system (TCS) T raction control is a driver aid feature that helps your vehicle maintain traction of the wheels, typically when driving on slippery and/or hilly road surfaces, by detecting and controlling wheel spin.
• Entering a paved road from a gravel road, or vice versa • Cornering while towing a heavily loaded trailer (refer to T railer towing in the T ires, Wheels and Loading chapter). The ESC system may be deactivated in certain situations. See the Switching off AdvanceT rac 威 with RSC 威 section following.
If you switch off the AdvanceT rac 威 with RSC 威 system, the stability control off light will illuminate steadily . Pressing the AdvanceT rac 威 with RSC 威 button again will turn off the stability control light.
STEERING T o help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until it stops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering fluid level (below the MIN mark on the reservoir).
PREP ARING TO DRIVE W ARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. W ARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
If the fuse is not blown and the brake lamps are working properly , the following procedure will allow you to move the gearshift lever from P (Park): 1. Apply the parking brake, and turn the ignition to the on position. 2. Remove the lower trim panel under the steering column.
AUTOMA TIC TRANSMISSION OPERA TION (IF EQUIPPED) Driving with a 5–speed automatic transmission (if equipped) This vehicle is equipped with an adaptive transmission shift strategy . Adaptive shift strategy offers the optimal transmission operation and shift quality .
D (Drive) with Overdrive The normal driving position for the best fuel economy . T ransmission operates in gears one through five. D (Drive) without Overdrive D (Drive) without Overdrive can be deactivated by pressing the transmission control switch on the end of the gearshift lever .
If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow , it may be rocked out by shifting between forward and reverse gears, stopping between shifts in a steady pattern.
Do not drive with your foot resting on the clutch pedal or use the clutch pedal to hold your vehicle at a standstill while waiting on a hill. These actions will severely reduce the life of the clutch and could nullify a clutch warranty claim.
Reverse 1. Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage the transmission. 2. Move the gearshift lever into the neutral position and wait at least three seconds before shifting into R (Reverse).
FOUR-WHEEL DRIVE (4WD) OPERA TION (IF EQUIPPED) W ARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter . Four–wheel drive (4WD) supplies power to all four wheels. 4WD should not be operated on dry pavement; driveline damage may occur .
Shifting between 2H (2WD High) and 4H (4WD High) • Move the 4WD control between 2H and 4H at a stop or any forward speed. Note: Do not perform this operation if the rear wheels are slipping. Shifting to/from 4L (4WD Low) Note: Some noise may be heard as the 4WD system shifts or engages.
Y ou should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area. T o maintain steering and braking control of your vehicle, you must have all four wheels on the ground and they must be rolling, not sliding or spinning.
If your vehicle gets stuck If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear . Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur .
4WD systems 4WD (when you select a 4WD mode) uses all four wheels to power the vehicle. This increases traction, enabling you to drive over terrain and road conditions that a conventional two-wheel drive vehicle cannot. Power is supplied to all four wheels through a transfer case.
when you are driving over sand, apply the accelerator slowly and avoid spinning your wheels. If the vehicle does slide, steer in the direction of the slide until you regain control of the vehicle. If the transmission, transfer case or front axle are submerged in water , their fluids should be checked and changed, if necessary .
Apply just enough power to the wheels to climb the hill. T oo much power will cause the tires to slip, spin or lose traction, resulting in loss of vehicle control. Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating.
W ARNING: If you are driving in slippery conditions that require tire chains or cables, then it is critical that you drive cautiously . Keep speeds down, allow for longer stopping distances and avoid aggressive steering to reduce the chances of a loss of vehicle control which can lead to serious injury or death.
DRIVING THROUGH W A TER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).
ROADSIDE ASSIST ANCE V ehicles sold in the U.S. : Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty .
U.S. Ford and Lincoln vehicle customers who require Roadside Assistance, call 1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount for towing to the nearest dealership within 35 miles (56 km).
FUEL PUMP SHUT -OFF SWITCH This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switch may have been activated.
Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.
The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 5A Instrument panel dimmer switch 2 10A T railer tow park lamps 3 10A Right low beam .
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 9 5A Cluster air bag indicator 10 10A Cluster (run/start), 4x4 module (run/start) 11 10A Passenger compartment fuse pan.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 30 5A Power mirrors 31 20A Front park lamps, Rear park lamps, License plate lamps, Dimmer switch, T railer tow park lam.
If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter . 2.3L engine (if equipped) The high-current fuses are coded as follows.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 11 30A** Powertrain control module (PCM) relay 12 — Not used 13 30A** Blower motor (climate control) 14 — Not used 15 — Not.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 39 15A* PCM power 40 — Not used 41 10A* Automatic transmission 42 7.5A* T railer tow (left turn) 43 20A* Engine fan relay coil,.
4.0L engines (if equipped) The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 40A** Passenger compartment fuse panel 2 — Not used 3 40A** Passenger.
Fuse/Relay Location Fuse Amp Rating Protected Circuits 12 — Not used 13 30A** Blower motor (climate control) 14 — Not used 15 — Not used 16 — Not used 17 40A** Anti-lock brake system (ABS) mod.
Fuse/Relay Location Fuse Amp Rating Protected Circuits 41 10A* Automatic transmission 42 7.5A* T railer tow (left turn) 43 20A* A/C relay coil, IAC, Mass air flow sensor , Heated exhaust gas oxygen se.
Have a flat serviced by an authorized dealer in order to prevent damage to the TPMS sensors, refer to T ire pressure monitoring system (TPMS) in the T ires, Wheels and Loading chapter .
• T ow a trailer • Use snow chains on the end of the vehicle with the dissimilar spare tire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • T ry .
• Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible.
Removing the spare tire or spare tire and tether (if equipped) 1. Assemble the jack handle to the lug wrench as shown in the illustrations. When connecting the jack handle, assemble the following: • One handle extension and one typical extension. T o assemble, slide parts together .
3. Insert the square end of the jack handle into the rear access hole located just above the rear bumper and below the tailgate. Forward motion will stop and resistance to turning will be felt when properly engaged. 4. T urn the handle counterclockwise until tire is lowered to the ground and the cable is slightly slack.
9. Use the attached fastener strap (on spare tire tether) to attach the tether end to the winch retainer prior to raising to the installed position. Tire change procedure W ARNING: When one of the fro.
2. Insert tapered end of the lug wrench behind hub caps and twist them off. 3. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.
W ARNING: T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the differential as a jacking point.
1. Place the tire on end with the valve stem facing rearward, away from the vehicle. 2. Place the tether into the bolt holes in the wheel and attach the lug nut using the lug wrench.
WHEEL LUG NUT TORQUE SPECIFICA TIONS Retighten the lug nuts to the specified torque within 100 miles (160 km) after any wheel disturbance (rotation, flat tire, wheel removal, etc.). Lug nut socket size/Bolt size Wheel lug nut torque* ft-lb N • m 1 ⁄ 2 x 20 100 135 * T orque specifications are for nut and bolt threads free of dirt and rust.
Do not attempt to push-start your automatic transmission vehicle. Automatic transmissions do not have push-start capability . Attempting to push-start a vehicle with an automatic transmission may cause transmission damage.
1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery .
Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery . 1. Remove the jumper cable from the ground metal surface.
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
Emergency towing In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer , or flatbed transport vehicle) your vehicle (regardless of transmission .
GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-565-3673 (FORD) Online www .ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P .
In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws.
Y ou are required to submit your warranty dispute to BBB AUTO LINE before asserting in court any rights or remedies conferred by California Civil Code Section 1793.22(b). Y ou are also required to use BBB AUTO LINE before exercising rights or seeking remedies created by the Federal Magnuson-Moss W arranty Act, 15 U.
Y ou can get more information by calling BBB AUTO LINE at 1-800-955-5100, or writing to: BBB AUTO LINE 4200 W ilson Boulevard, Suite 800 Arlington, V irginia 22203–1833 BBB AUTO LINE applications can also be requested by calling the Ford Motor Company Customer Relationship Center at 1-800-392-3673.
The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel.
If your vehicle must be serviced while you are traveling or living in the Middle East, contact the nearest authorized dealer . If the authorized dealer cannot help you, contact: Ford Middle East Customer Relationship Center P .
REPORTING SAFETY DEFECTS (U.S. ONL Y) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft 威 Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
W AXING • W ash the vehicle first. • Use a quality wax that does not contain abrasives. • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area.
• Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. In Canada use Motorcraft Engine Shampoo (CXC-66-A).
4.0L V6 ENGINE PLASTIC (NON-P AINTED) EXTERIOR P ARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer . • For routine cleaning, use Motorcraft 威 Detail W ash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and T ar Remover (ZC-42).
• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. If you cannot remove those streaks after cleaning with the glass cleaner or i.
3. If necessary , apply more soap and water solution or cleaning product to a clean, white, cotton cloth and press the cloth onto the soiled area–allow this to set at room temperature for 30 minutes. 4. Remove the soaked cloth, and if it is not soiled badly , use this cloth to clean the area by using a rubbing motion for 60 seconds.
• Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber , vinyl and plastics, or oil/petroleum-based leather conditioners.
• Clean the surfaces using the steps outlined in the Cleaning section. • Ensure the leather is dry then apply a nickel-sized amount of conditioner to a clean, dry cloth. • Rub the conditioner into leather until it disappears. Allow the conditioner to dry and repeat the process for the entire interior .
SERVICE RECOMMENDA TIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service.
Working with the engine on 1. For vehicles equipped with an automatic transmission, set the parking brake and shift to P (Park). For vehicles equipped with a manual transmission, set the parking brake, press and hold the clutch pedal, place the gearshift in N (Neutral), and release the clutch pedal.
IDENTIFYING COMPONENTS IN THE ENGINE COMP ARTMENT 2.3L I4 engine 1. W indshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil dipstick 4. T ransmission fluid dipstick (automatic transmission) 5. Engine oil filler cap 6. Brake fluid reservoir 7.
4.0L V6 engine 1. W indshield washer fluid reservoir 2. T ransmission fluid dipstick (automatic transmission) 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Power distribution box 7. Clutch fluid reservoir (manual transmission) 8.
WINDSHIELD W ASHER FLUID • 2.3L engine • 4.0L engine Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
W asher fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’ s paint finish, wiper blades or washer system. W ARNING: If you operate your vehicle in temperatures below 40°F (5°C), use washer fluid with antifreeze protection.
2. T urn the engine off and wait 15 minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmission) or 1 (First) (manual transmission). 4. Open the hood. Protect yourself from engine heat.
• If the oil level is below the lower hole or the MIN mark, add enough oil to raise the level between the two holes or between the MIN-MAX range. • Oil levels above the upper hole or MAX mark may cause engine damage. Some oil must be removed from the engine by an authorized dealer .
Use SAE 5W -20 engine oil Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.
Use SAE 5W -30 engine oil Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.
For longer , trouble-free operation, keep the top of the battery clean and dry . Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush.
Because your vehicle’ s engine is electronically controlled by a computer , some control conditions are maintained by power from the battery . When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance.
ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in the scheduled maintenance information. The coolant concentration should be maintained at 50/50 coolant and distilled water .
• 2.3L engine • 4.0L engine Maintenance and Specifications 238 201 1 Ranger (ran) Owners Guide, 2nd Printing USA (fus).
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the FULL COLD level or within the COLD FILL RANGE as listed on the engine coolant reservoir (depending upon application). • Refer to the scheduled maintenance information for service interval schedules.
• A large amount of water without engine coolant may be added, in case of emergency , to reach a vehicle service location. In this instance, the cooling system must be drained and refilled with a 50/50 mixture of engine coolant and distilled water as soon as possible.
If you removed the radiator cap in an overflow system, fill the radiator until the coolant is visible and radiator is almost full. 6. Replace the cap. T urn until tightly installed. Cap must be tightly installed to prevent coolant loss. After any coolant has been added, check the coolant concentration (refer to Checking engine coolant ).
above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage. • If available, refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months.
W ARNING: If you do not use the proper fuel filler cap, excessive vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in serious personal injury . W ARNING: Automotive fuels can cause serious injury or death if misused or mishandled.
• Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result.
• DO NOT use a device that would hold the fuel pump handle in the fill position. Fuel filler cap When fueling your vehicle: 1. T urn the engine off. 2. Carefully turn the fuel filler cap counterclockwise until it spins off. 3. Carefully hang the cap from the tether .
Choosing the right fuel Use only UNLEADED fuel or UNLEADED fuel blended with a maximum of 10% ethanol. Do not use fuel ethanol (E85), diesel, methanol, leaded fuel or any other fuel. The use of leaded fuel is prohibited by law and could damage your vehicle.
Many of the world’ s automakers approved the W orld-W ide Fuel Charter that recommends gasoline specifications to provide improved performance and emission control system protection for your vehicle. Gasolines that meet the W orld-W ide Fuel Charter should be used when available.
The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty . Empty reserve is the small amount of fuel remaining in the fuel tank after the fuel gauge indicates empty .
Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’ s fuel economy under current driving conditions. Additionally , keeping records during summer and winter will show how temperature impacts fuel economy .
• Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in scheduled maintenance information. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed.
If other than Ford, Motorcraft 威 or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability .
2. Poor fuel quality or water in the fuel—the engine may misfire or run poorly . 3. The fuel cap may not have been securely tightened. See Fuel filler cap in this chapter .
The OBD-II system is designed to check the emission control system during normal driving. A complete check may take several days. If the vehicle is not ready for I/M testing, the following driving cyc.
2. While the engine idles, turn the steering wheel left and right several times. 3. T urn the engine off. 4. Check the fluid level in the reservoir . It should be between the MIN and MAX lines. Do not add fluid if the level is within this range. 5. If the fluid is low , add fluid in small amounts, until it reaches between the MIN and MAX lines.
1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir . 2. Remove cap and rubber diaphragm from reservoir . 3. Add fluid until the level reaches the step in the reservoir . 4. Reinstall rubber diaphragm and cap onto reservoir .
Refer to the Maintenance product specifications and capacities section in this chapter for the correct fluid type. The use of any other non-approved fluid may cause internal transmission damage. 10. Fluid can be checked at ambient temperatures between 50–95°F (10–30°C).
3. Fluid level should be at the bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely . Use only fluid that meets Ford specifications.
DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Y our vehicle is equipped with universal joints that do not require lubrication. If the original universal joints are replaced with universal joints equipped with grease fittings, periodic lubrication will be necessary .
6. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover . This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. 7. Replace the air filter housing cover and secure the clamps.
• Lubricate all hood, door and trunk lid hinges, and latches with a light grade oil. See the Cleaning chapter for more information. • Cover interior trim to prevent fading.
Brakes • Make sure brakes and parking brake are fully released. T ires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle are covered with grease to prevent rust. • Move vehicles at least 25 feet (8 m) every 15 days to lubricate working parts and prevent corrosion.
MOTORCRAFT P ART NUMBERS Component 2.3L I4 Engine 4.0L V6 Engine Air filter element F A-1744 F A-1744 Fuel filter FG-1036 FG-1036 Battery BXT -59 BXT -59 Oil filter FL-910S FL-820S Spark plugs 1 1 For spark plug replacement, see your authorized dealer .
MAINTENANCE PRODUCT SPECIFICA TIONS AND CAP ACITIES Item Capacity Ford Part Name or Equivalent Ford Part Number / Ford Specification Brake fluid and (clutch fluid–if equipped) Between MIN/MAX on bra.
Item Capacity Ford Part Name or Equivalent Ford Part Number / Ford Specification Engine oil (2.3L engine) 4.0 quarts (3.8L) Motorcraft 威 SAE 5W -20 Premium Synthetic Blend Motor Oil (US) Motorcraft 威 SAE 5W -20 Super Premium Motor Oil (Canada) 2 XO-5W20-QSP (US) CXO-5W20-LSP12 (Canada) / WSS-M2C930-A and API Certification Mark Engine oil (4.
Item Capacity Ford Part Name or Equivalent Ford Part Number / Ford Specification T ransfer case fluid (4X4) 1.25 quarts (1.2L) Motorcraft 威 T ransfer Case Fluid XL–12 / — Power steering fluid Fill between MIN/MAX line on reservoir Motorcraft 威 MERCON 威 VA T F XT -5-QM / MERCON 威 V Front axle fluid (4X4) 3.
Item Capacity Ford Part Name or Equivalent Ford Part Number / Ford Specification Fuel tank–SuperCab 19.5 gallons (73.8L) —— 1 Add the coolant type originally equipped in your vehicle. 2 Use of synthetic or synthetic blend motor oil is not mandatory .
ENGINE DA T A Engine 2.3L I4 engine 4.0L V6 engine Cubic inches 138 245 Required fuel Minimum 87 octane Minimum 87 octane Firing order 1-3-4-2 1-4-2-5-3-6 Ignition system EDIS EDIS Spark plug gap 0.049–0.053 inch (1.25–1.35 mm) 0.052–0.056 inch (1.
• 4.0L V6 engine with A/C • 4.0L V6 engine without A/C Maintenance and Specifications 268 201 1 Ranger (ran) Owners Guide, 2nd Printing USA (fus).
IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint Devices and their location 3. Make, vehicle line, series, body type 4. Engine type 5.
FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for your vehicle through your local Ford or Ford of Canada dealer .
Peace of mind • Keyless entry keypad • Seat covers* • Remote start • Back up camera* • V ehicle security systems • Back up alarm* • Wheel locks • Hitch mounted parking sensor* • V eh.
FORD ESP EXTENDED SERVICE PLANS (U.S. ONL Y) More than 30 million Ford and Lincoln owners have discovered the powerful protection of Ford ESP . It is the only extended service plan backed by Ford Motor Company , and provides “peace of mind” protection beyond the New V ehicle Limited W arranty coverage.
Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract.
Ford Extended Service Plan 275 201 1 Ranger (ran) Owners Guide, 2nd Printing USA (fus).
FORD ESP EXTENDED SERVICE PLANS (CANADA ONL Y) Y ou can get more protection for your vehicle by purchasing a Ford Extended Service Plan (ESP). Ford ESP is the only service contract backed by Ford Motor Company of Canada, Limited.
GENERAL MAINTENANCE INFORMA TION Why maintain your vehicle? This guide describes the scheduled maintenance required for your vehicle. Carefully following this schedule helps protect against major repair expenses resulting from neglect or inadequate maintenance and may also help to increase the value of your vehicle when you sell or trade it.
Chemicals or additives not approved by Ford are not required for factory recommended maintenance. In fact, Ford Motor Company recommends against the use of such additive products unless specifically recommended by Ford for a particular application.
one-stop service from routine maintenance like oil changes and tire rotations to repairs like brake service, check out the value your dealers can offer . Owner checks and services Certain basic maintenance checks and inspections should be performed by the owner or a service technician at the intervals indicated.
Multi-point inspection In order to keep your vehicle running right, it is important to have the systems on your vehicle checked regularly . This can help identify potential issues and prevent major problems.
Scheduled Maintenance 281 201 1 Ranger (ran) Owners Guide, 2nd Printing USA (fus).
NORMAL SCHEDULED MAINTENANCE AND LOG The following section contains the “Normal Schedule”. This schedule is presented at specific mileage (kilometer) intervals with exceptions noted.
Miles (x 1,000)* 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75 Kilometers (x 1,000)* 12 24 36 48 60 72 84 96 108 120 Months* 6 12 18 24 30 36 42 48 54 60 Change engine oil and filter • ••••••.
Miles (x 1,000)* 82.5 90 97.5 105 112.5 120 127.5 135 142.5 150 Kilometers (x 1,000)* 132 144 156 168 180 192 204 216 228 240 Months* 66 72 78 84 90 96 102 108 114 120 Change engine oil and filter •.
Every 15,000 miles (24,000 km) Replace cabin air filter (if equipped) Every 30,000 miles (48,000 km) Replace climate-controlled seat filter (if equipped) Replace engine air filter Replace fuel filter .
Maintenance schedule log D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A .
D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D A.
D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D A.
SPECIAL OPERA TING CONDITIONS If you operate your vehicle primarily in one of the more demanding conditions listed below , you will need to have some items maintained more frequently . If you only occasionally operate your vehicle under these conditions, it is not necessary to perform the additional maintenance.
Extensive idling and/or low-speed driving for long distances as in heavy commercial use such as delivery , taxi, patrol car or livery Inspect frequently , service as required – Replace cabin air fil.
Operating in dusty conditions such as unpaved or dusty roads Inspect frequently , service as required – Replace cabin air filter (if equipped) – Replace engine air filter Every 5,000 miles (8,000 .
Off-road operation Inspect frequently , service as required – Inspect steering linkage, ball joints and U-joints; lubricate if equipped with grease fittings – Replace cabin air filter (if equipped.
Special operating condition log D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P.
D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D A.
EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. They are listed below: Normal vehicle axle maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic fluid and light duty trucks equipped with Ford-design axles are lubricated for life.
ENGINE COOLANT CHANGE RECORD Initial change 6 years or 105,000 miles (168,000 km) (whichever comes first) After initial change Every 3 years or 45,000 miles (72,000 km) Middle East hot climate specifi.
Engine coolant change log D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A.
A ABS (see Brakes) ..................... 156 AdvanceT rac .............................. 159 Airbag supplemental restraint system .................................... 84, 92 and child safety seats .............. 86 description ........................
wiper blades ............................ 220 Clock adjust AM/FM ....................................... 20 AM/FM stereo CD ..................... 21 Clutch fluid .......................................... 254 operation while driving .......... 169 recommended shift speeds .
Fuel ............................................ 242 calculating fuel economy ....... 247 cap ........................................... 245 capacity ................................... 263 choosing the right fuel ...........246 detergent in fuel ..
Load limits ................................. 134 Locks doors .......................................... 56 Lubricant specifications ........... 263 Lug nuts ....................................203 M Manual transmission ................. 169 fluid capacities .
Safety Compliance Certification Label .................... 269 Satellite Radio Information ........ 32 Scheduled Maintenance Guide Normal Scheduled Maintenance and Log .............282 Seats ............................................63 child safety seats .
W asher fluid .............................. 229 W ater , Driving through ............. 180 W indows power ......................................... 51 W indshield washer fluid and wipers .......................................... 49 checking and adding fluid .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Ford Ranger (2011) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Ford Ranger (2011) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Ford Ranger (2011), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Ford Ranger (2011) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Ford Ranger (2011), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Ford Ranger (2011).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Ford Ranger (2011). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Ford Ranger (2011) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
