Manuel d'utilisation / d'entretien du produit 2000 Mustang du fabricant Ford
Aller à la page of 224
Before driving Introduction 2 Instrumentation 6 Controls and features 18 Seating and safety restraints 62 Starting and driving Starting 90 Driving 95 Roadside emergencies 1 16 Servicing Maintenance and care 133 Capacities and specifications 191 Customer assistance 197 Reporting safety defects 21 1 Index 212 All rights reserved.
The following warning may be required by California law: CALIFORNIA Proposition 65 W arning Engine exhaust, some if its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer , or birth defects or other reproductive harm.
W ARNINGS W arnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment. BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently .
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation W.
V ehicle Symbol Glossary Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power .
P ! BRAKE L 0 00000 0 0 C E F H LH 10 20 30 20 40 60 80 100 120 160 180 40 50 60 70 80 90 4 5 6 7 3 2 1 H THEFT RPMX1000 FUEL DOOR SELECT/RESET LOW FUEL O/D OFF AIR BAG SERVICE ENGINE SOON MPH km/h . REAR DEF OFF HI LO OFF ON RSM SET ACC COAST Headlamp control (pg.
POWER AUDIO VOLUME AM/FM REW FF PLAY EJCT 1 2 3 4 5 CLOCK AUTO PRESET PROG AUTOM ATIC DNR CrO 2 SCAN TUNE SEEK FM1 ST LO HI OFF FLOOR MIX VENT NORM A/C MAX A/C Climate control system (pg.
W ARNING LIGHTS AND CHIMES Base instrument cluster Optional instrument cluster T urn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster , check for a burned-out turn signal bulb.
position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter . Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly , requiring electrical system service.
to check the bulb. If it comes on after the engine is started, one of the engine’ s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted. The vehicle will usually be drivable and will not require towing.
Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
T raction Control Y active Momentarily illuminates when the ignition is turned to ON. It also illuminates when the T raction Control y system begins applying and releasing the brakes and adjusting the engine characteristics to limit a wheelspin condition.
added. This lamp will also illuminate when the ignition is turned to ON and the engine is off. For more information on adding engine coolant, refer to Engine coolant in the Maintenance and care chapter . Safety belt warning chime Sounds to remind you to fasten your safety belts.
Optional instrument cluster gauges Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. Speedometer Indicates the current vehicle speed. • Base instrument cluster • Optional instrument cluster Odometer Registers the total kilometers (miles) of the vehicle.
• Base instrument cluster • Optional instrument cluster T rip odometer Registers the kilometers (miles) of individual journeys. Press and release the reset button until a “T” appears in the display (this represents the trip mode). Press and hold the button for three seconds to reset.
Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains in the normal range (the area between the “L” and “H”). If the gauge indicates low pressure, stop the vehicle as soon as safely possible and switch off the engine immediately .
HEADLAMP CONTROL • Pull the headlamp control toward you to the first position to turn on the parking lamps, tail lamps, license plate lamps and marker lamps. • Pull the headlamp control toward you to the outer position to turn on the headlamps (in addition to the previous lamps).
P ANEL DIMMER CONTROL T o adjust the brightness of the instrument panel: • Rotate clockwise/ counterclockwise when the headlamp control is in the parking lamp or low-beam position. T o turn on the courtesy lamps: • Rotate fully counterclockwise. REAR WINDOW DEFROSTER (IF EQUIPPED) The rear defroster control is located on the instrument panel.
CLIMATE CONTROL SYSTEM Manual heating and air conditioning system Fan speed control Controls the volume of air circulated in the vehicle. T emperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
faster . Airflow will be from the instrument panel registers. This mode can also be used to reduce undesirable odors from entering the vehicle. • A/C-Uses outside air to cool the vehicle. It is quieter than MAX A/C but not as economical. Airflow will be from the instrument panel registers.
Operating tips • In humid weather , select before driving. This will reduce fogging on your windshield. After a few minutes, select any desired position. • T o reduce humidity buildup inside the vehicle, don’t drive with the climate control system in the OFF or MAX A/C position.
USING YOUR AUDIO SYSTEM AM/FM Stereo/Cassette/Premium Sound Power control Press the control to turn the audio system on or off. V olume control Press the control to raise or lower volume.
Tune adjust in radio mode T une adjust allows you to tune in a particular radio station. Y ou can manually locate the station by using the Automatic Music Search (AMS) button. • Press the AMS control until the display shows TUNE. • Press and release either or on the SEEK control to change to the next frequency up or down.
• Press to listen to the previous selection on the tape. • Press to listen to the next selection on the tape. The tape deck stops and returns to play mode when the AMS circuit senses a blank section on the tape.
held in memory on the control you selected. Repeat the steps for each station memory preset button you want to set. If the battery is disconnected, the memory preset stations will need to be reset. Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output.
• Press the (+) side of the volume control to shift sound to the right speakers. • Press the (−) side of the volume control to shift sound to the left speakers. Speaker fade adjust Speaker sound distribution can be adjusted between the front and rear speakers.
T ape eject Press the control to stop and eject a tape. Dolby T noise reduction Dolby t noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby t noise reduction. Dolby t noise reduction is manufactured under license from Dolby t Laboratories Licensing Corporation.
Power control Press the control to turn the audio system on or off. V olume control Press the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
• Press and hold down or to quickly move through the frequencies. Seek function The seek function control works in radio or tape mode. Seek function in radio mode This feature allows you to automatically select listenable stations up or down the frequency band.
Use the SEEK button to scan up or down the frequency band. • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band.
3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. If the battery is disconnected, the memory preset stations will need to be reset. Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output.
• Press the (+) side of the volume control to shift sound to the right speakers. • Press the (−) side of the volume control to shift sound to the left speakers. Speaker fade adjust Speaker sound distribution can be adjusted between the front and rear speakers.
Press the control to fast forward the tape. Once the end of the tape is reached, tape direction reverses and the opposite side of the tape plays. T ape eject Press the control to stop and eject a tape. Dolby T noise reduction Dolby t noise reduction reduces the amount of hiss and static during tape playback.
Single Disc CD Player Power and volume control The compact disc player operates when the audio system is on and a CD is inserted (label side up). The volume is controlled by the VOLUME control on the audio system. Play function The system enters the PLA Y mode when a CD is loaded, label side up, into the disc opening.
approximately eight seconds. This continues until you press the SCAN control a second time or eject the CD. While in the scan mode, the display flashes SCAN. Reverse/fast forward T o quickly search for a particular point in a selection, press the right side of the REV/FF control (to fast forward) or the left side (to reverse).
Shuffle feature The shuffle feature plays all tracks on the current CD in random order . Press the SHUFFLE control to start this feature. Random order play will continue until the control is pressed again. Eject Push the EJECT control to stop CD play , eject the CD, and resume radio or tape operation.
Cleaning compact discs Inspect all discs for contamination before playing. If necessary , clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion. CD and CD player care • Handle discs by their edges only .
and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all frequencies are used in a given area. Radio reception factors Three factors can affect radio reception: • Distance/strength.
T RUNK REMOTE CONTROL The remote trunk release control is located in the glove compartment. Press to open trunk. TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position.
FLASH TO PASS Pull toward you to activate and release to deactivate. POSITIONS OF THE IGNITION 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal.
Never adjust the steering wheel when the vehicle is moving. SPEED CONTROL T o turn speed control on • Press ON. V ehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery , or unpaved.
T o set a speed • Press SET/SET ACC/ SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
• Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET/SET ACC/SET ACCEL. Y ou can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed.
• Depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. T o return to a previously set speed • Press RES/RSM/ RESUME. For RES/ RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph).
POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open. Express down T o make the driver window open fully without holding the window control, press the driver window control completely down and release quickly .
for the driver’ s press the control. Press the control again to restore the window controls. POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors.
Use only soft cups in the cupholder . Hard objects can injure you in a collision. Foglamp control (if equipped) T urn on the parking lamps or the low-beam headlamps. Press the top portion of the foglamp control, located on the center console, to activate the foglamps.
3. Unclamp the top from the windshield header at both the right and left sides by pulling each clamp rearward until the hook in the windshield header is free.
2. Push boot forward until rear attachment engages under molding. 3. Push forward flap of boot until both clips engage under trim panel edge. Repeat on other side of vehicle. 4. T uck side attachments under molding. Repeat on other side of vehicle. 5.
Raising the convertible top The convertible top will not operate unless the parking brake is engaged. Do not raise the top while the vehicle is moving because the top may be severely damaged. T o raise the convertible top: 1. Bring the vehicle to a complete stop.
AUXILIARY POWER POINT The power point is an additional power source for electrical accessories. T RACTION CONTROL Y This control can be used to turn the T raction Control y on or off. Refer to the T raction Control y section of the Driving chapter for more information.
The transmission will operate in all gears except overdrive. T o return to normal overdrive mode, press the T ransmission Control Switch again. The O/D OFF indicator light will no longer be illuminated. When you shut off and re-start your vehicle, the transmission will automatically return to normal (Overdrive) mode.
Unlocking the doors Press this control to unlock the driver’ s door . The interior lamps will illuminate. W ith the all-door remote entry system, press the control a second time within three seconds to unlock the passenger door . Locking the doors Press this control to lock all doors.
Sounding a panic alarm Press this control to activate the alarm. T o deactivate the alarm, press the control again or turn the ignition to ACC or ON. This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada.
Replacing lost transmitters T ake all your vehicle’ s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed into memory), perform .
T o replace the batteries: 1. T wist a thin coin between the two halves of the transmitter near the key ring. DO NOT T AKE THE FRONT P ART OF THE TRANSMITTER AP ART . 2. Place the positive (+) side of new batteries down. Refer to the diagram inside the transmitter unit.
used to purchase gasoline or similar items on the same key ring as the P A TS ignition key may cause vehicle starting problems. If present, you need to keep these objects from touching the P A TS ignition key while starting the engine.
of eight keys). Y our dealership can program your new SecuriLock y key(s) to your vehicle or you can do it yourself using the following simple procedure. T o program a new SecuriLock y key yourself, you will need two previously programmed SecuriLock y keys (keys that already operate your vehicle’ s engine).
key/valet key) into the ignition and turn the ignition from OFF to ON (maintain ignition in ON for at least one second). This step will program your new SecuriLock y key . 6. T o program additional SecuriLock y key(s), repeat this procedure from step 1.
T o open the luggage compartment door (lid) from the inside, pull the illuminated “T” shaped handle and push up on the trunk lid. The material that the handle is made of will glow for hours in the darkness of the luggage compartment following brief exposure to ambient light.
SEA TING Adjustable head restraints (if equipped) Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision.
Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
The control is located on the front outboard corner of the driver’ s seat. Press front to raise or lower the front portion of the seat cushion. Press rear to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down.
The rotating boot on the front seat belt is designed to allow rear seat entry/exit. T o enter the rear seat: 1. Remove seat belt from seat belt holder on top of front seat. 2. Rotate the safety belt boot rearward. 3. Enter the rear seat in front of the safety belt.
T o reduce the risk of injury , make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving.
Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Combination lap and shoulder belts Before fastening the safety belt, make sure the shoulder belt passes through the belt holder on the top of the seatback.
The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described b.
How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Safety belt extension assembly If the safety belt assembly is too short, even when fully extended, 20 cm (8 inches) can be added to the safety belt assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained from your dealer at no cost.
Belt minder (if equipped) The Belt Minder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’ s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster .
The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider ... 9 Crashes are rare events 9 36 700 crashes occur every day . The more we drive, the more we are exposed to 9 rare 9 events, even for good drivers.
Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase risk of injury in an accident. T o disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below .
2. W ait until the safety belt warning light turns off. (Approximately 1–2 minutes) • Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated. 3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled.
front seat belt buckle assemblies, buckle support assemblies (slide bar -if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seatback (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after a collision.
Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
• Recline the seat slightly (one or two degrees) from the upright position. Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury .
Air bags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic. While the system is designed to help reduce serious injuries, contact with a deploying air bag may also cause abrasions, swelling or temporary hearing loss.
system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Important child restraint precautions Y ou are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children.
Do not leave children, unreliable adults, or pets unattended in your vehicle. T o improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards.
Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly , the child may be injured in a sudden stop or collision.
Carefully follow all of the manufacturer’ s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly , the child may be injured in a sudden stop or collision.
Children 12 and under should be properly restrained in the rear seat whenever possible. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. T ether straps are available as an accessory for many older safety seats.
3. Locate the correct anchor for the selected seating position as shown previously . For Coupe only: 4. Open the tether anchor covers. 5. Clip the tether strap to the anchor as shown. For Convertible only: The tether anchors on the convertible are located on the lower backside of the seatback.
5. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision.
PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Important safety precautions A computer system controls the engine’ s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically , have the vehicle checked.
3. T urn the key to 4 (ON) without turning the key to 5 (ST ART). If there is difficulty in turning the key , firmly rotate the steering wheel left and right until the key turns freely .
2. If the temperature is above –12°C (10°F) and the engine does not start within five seconds on the first try , turn the key to OFF , wait 10 seconds and try again. 3. If the temperature is below -12° C (10° F) and the engine does not start in 15 seconds on the first try , turn the key OFF and wait 10 seconds and try again.
If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately . Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you. Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service.
BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system.
The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency . The wheels are prevented from locking even when the brakes are firmly applied.
stopping distance. Always leave enough room between your vehicle and the vehicle in front of you to stop. • W e recommend that you familiarize yourself with this braking technique.
(when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First Gear) (manual transmission). The parking brake is not recommended to stop a moving vehicle.
controlled by automatically applying and releasing the rear brakes in conjunction with engine torque reductions. Engine torque reduction is realized via the fully electronic spark and fuel injection systems. This process is very sensitive to driving conditions and very fast acting.
STEERING Y our vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. T o prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
If it is necessary to use the above procedure to move the gearshift lever , it is possible that a fuse has blown or the vehicle’ s brakelamps are not operating properly . Refer to Fuses and relays in the Roadside emergencies chapter . Do not drive your vehicle until you verify that the brakelamps are working.
Driving with an automatic overdrive transmission with console gearshift and O/D off switch Y our automatic overdrive transmission provides fully automatic operation in either D (Overdrive) or with the O/D OFF switch depressed. Driving with the gearshift lever in D (Overdrive) gives the best fuel economy for normal driving conditions.
Understanding gearshift positions P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This position locks the transmission and prevents the rear wheels from turning. Always set the parking brake fully and make sure the gearshift lever is latched in P (Park).
(Overdrive) The normal driving position for the best fuel economy . T ransmission operates in gears one through four . (Overdrive) can be deactivated by pressing the transmission control switch on the gearshift lever . The transmission control indicator light (TCIL) will illuminate on the instrument cluster .
T o return to (Overdrive) mode, press the transmission control switch. The O/D OFF indicator will no longer be illuminated. Each time the vehicle is started, the transmission will automatically return to normal overdrive mode.
MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch V ehicles equipped with a manual transmission have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. When starting a vehicle with a manual transmission, you must: 1.
• Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill while waiting on a hill. These actions will greatly reduce clutch life. Recommended shift speeds Do not downshift into 1 (first) when your vehicle is moving faster then 24 km/h (15 mph).
4. T urn the ignition key to position 3 (OFF). Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully .
If R (Reverse) is not engaged, push the clutch pedal down and put the gearshift back into Neutral. Then, release the clutch pedal for a moment and repeat steps 3 through 6. Removing key from ignition • T urn the ignition key to position 3 (OFF). • Push the release lever forward and rotate the key towards you and remove.
• Payload: Combined maximum allowable weight of cargo, passengers and optional equipment. The payload equals the gross vehicle weight rating minus base curb weight. • GVW (Gross V ehicle W eight): Base curb weight plus payload weight. The GVW is not a limit or a specification.
• T railer W eight Range: Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating. Remember to figure in the tongue load of your loaded trailer when figuring the total weight. Do not exceed the GVWR or the GA WR specified on the certification label.
T RAILER TOWING Y our vehicle is capable of towing a trailer up to 454 kg (1 000 lbs.) gross trailer weight with a maximum tongue load of 45 kg (100 lbs.
adjusted to the manufacturer’ s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’ s hydraulic brake system directly to your vehicle’ s brake system. Y our vehicle may not have enough braking power and your chances of having a collision greatly increase.
your Scheduled Maintenance guide for more information. T railer towing tips • Practice turning, stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles.
ensure that your transmission is not damaged. • Place the transmission in N (Neutral). • Maximum speed is 56 km/h (35 mph). • Maximum distance is 80 km (50 miles). If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) must be exceeded, you must disconnect the driveshaft.
GETTING ROADSIDE ASSIST ANCE T o fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty .
Should you need to arrange roadside assistance for yourself, Ford will reimburse a reasonable amount. T o obtain information about reimbursement, call 1-800-241-3673 in the United States for Ford or Mercury vehicles; or if you own a Lincoln vehicle, call 1–800–521–4140.
After a collision, if the engine cranks but does not start, the fuel pump shut-off switch may have been activated. The fuel pump shut-off switch is located on the left side of the trunk behind the trunk liner . Use the following procedure to reset the fuel pump shut-off switch.
Check the appropriate fuses before replacing any electrical components. Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 20A Cigar Lighter 2 20A Engine Controls 3 — Not Used 4 10A RH Low Beam Headlamp 5 1.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 19 15A Power Mirror Switch, GEM, Anti-Theft Relay , Power Door Locks, Door Ajar Switches 20 15A Convertible T op Switch.
Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’ s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description Relay 1 — Fog Lamp Interrupt Relay 2 — Int. Wiper Relay 3 — Wiper HI/LO Relay 4 — Starter Relay 5 — Fog Lamps 1 50A** (4.6L), 30A CB (3.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 25 — Not Used 26 30A** PCM 27 20A** DRL Module, Foglamp Relay 28 25A CB Convertible T op * Mini Fuses ** Maxi Fuses CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily .
• try to repair the temporary spare tire or remove it from its wheel • use the wheel for any other type of vehicle Tire change procedure T o prevent the vehicle from moving when you change a tire,.
4. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 5. Put the jack in the jack notch next to the tire you are changing. T urn the jack handle clockwise until the wheel is completely off the ground.
8. Lower the wheel by turning the jack handle counterclockwise. 9. Remove the jack and fully tighten the lug nuts in the order shown. 10. Put flat tire, jack and lug wrench away . Make sure jack is fastened so it does not rattle when you drive. 11. Unblock the wheels.
2. Place the lug nut wrench over the lug nut key and apply pressure on the key with the wrench. 3. Install the lug nut. JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage.
Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery .
4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.
1. Remove the jumper cable from the ground metal surface. 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s battery . 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4.
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a Scheduled Maintenance Guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service.
2. T urn off the engine and remove the key . 3. Block the wheels to prevent the vehicle from moving unexpectedly . • Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift in 1 (First). 3. T urn off the engine and remove the key .
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.8L OHV V6 engine 1. Engine oil filler cap 2. Engine oil dipstick 3. Brake fluid reservoir 4. Power distribution box 5. W indshield washer fluid reservoir 6. Battery 7. Power steering fluid reservoir 8.
4.6L SOHC V8 engine 1. Engine oil dipstick 2. Brake fluid reservoir 3. Power distribution box 4. W indshield washer fluid reservoir 5. Battery 6. Engine coolant reservoir 7. Power steering fluid reservoir 8. Engine oil filler cap 9. Air filter assembly 10.
3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick).
• 3.8L OHV V6 engine • 4.6L SOHC V8 engine • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1.
4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise until three clicks can be heard. T o avoid possible oil loss, DO NOT operate the vehicle with the engine oil level indicator and/or the engine oil filler cap removed.
BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the Scheduled Maintenance Guide for the service interval schedules. • 3.8L OHV V6 engine • 4.6L SOHC V8 engine 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir .
4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter . Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes.
WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low , add enough fluid to fill the reservoir . In very cold weather , do not fill the reservoir all the way .
A 50/50 mixture of distilled water and Ford Premium Engine Coolant provides: • maximum cooling system efficiency . • freeze protection down to -36° C (-34° F). • boiling protection up to 129° C (265° F). • protection against rust and other forms of corrosion.
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “cold fill level” as listed on the engine coolant reservoir . • Refer to the Scheduled Maintenance Guide for service interval schedules.
• DO NOT MIX recycled coolant and conventional coolant together in your vehicle. Mixing of engine coolants may harm your engine’ s cooling system. • The use of an improper coolant may harm engine and cooling system components and may void the warranty of your vehicle’ s engine cooling system.
Have your dealer check the engine cooling system for leaks if you have to add more than 1.0 liter (1.0 quart) of engine coolant per month. If equipped with the 3.8L V6 engine, to avoid scalding hot steam or coolant from being released from the engine cooling system, never remove the radiator cap from the radiator while the engine is running or hot.
which can be purchased from your dealer . Engine coolant refill procedure-3.8L V6 engine Use the following procedure when refilling the cooling system of a vehicle equipped with a 3.8L V6 engine. Failure to follow this warning may result in damage to the engine and engine cooling system.
12. Add a 50/50 mixture of engine coolant and distilled water to the radiator until full. 13. Reinstall the radiator cap. 14. Check the coolant level in the reservoir before you drive your vehicle the next few times (with the engine cool).
9. Check the coolant level in the reservoir before you drive your vehicle the next few times (with the engine cool). 10. If necessary , add a 50/50 mixture of engine coolant and distilled water to the engine coolant reservoir until the coolant level is at the “cold fill level” as listed on the reservoir .
protection characteristics of the engine coolant and may cause engine damage. • refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months.
If your vehicle is equipped with the 3.8L V6 engine, check the power steering fluid level with the engine at normal operating temperature. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).
If your vehicle is equipped with a 4.6L V8 engine, check the power steering fluid level with the engine at ambient temperature. Allow at least one-half hour after driving for the power steering fluid to cool. 1. Start the engine and allow the engine to idle.
been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer , the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature.
Y ou can check the fluid without driving if the ambient temperature is above 10°C (50°F). However , if fluid is added at this time, an overfill condition could result when the vehicle reaches normal operating temperature. The transmission fluid should be in this range if at normal operating temperature (66°C-77°C [150°F-170°F]).
An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Checking and adding manual transmission fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening.
BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules.
Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes. Always provide proper ventilation.
3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. T urn the A/C on and allow the engine to idle for at least one minute.
windshield wiper solution or a mild detergent. Rinse thoroughly with clean water . T o avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents. Changing the wiper blades T o replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position.
tread, winter -type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in T itle 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of T ransportation-T ire quality grades: The U.
T emperature A B C The temperature grades are A (the highest), B, and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Tire rotation Because your vehicle’ s tires perform different jobs, they often wear differently . T o make sure your tires wear evenly and last longer , rotate them as indicated in the Scheduled Maintenance Guide. If you notice that the tires wear unevenly , have them checked.
When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the tire pressure decal. Make sure that all tires are the same size, speed rating, and load-carrying capacity . Use only the tire combinations recommended on the label.
chains. Use chains on the tires only in an emergency or if the law requires them. Follow these guidelines when using snow tires and chains: • Chains may damage aluminum wheels. • Use only Cable T ype chains with size P225/55R16 or 245/45ZR17 tires.
The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury .
Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle. • Keep the fuel pump nozzle in contact with the fuel container while filling.
The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
a qualified service technician to prevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” unleaded gasoline.
If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. • Y our “Service Engine Soon” indicator may come on. For more information on the “Service Engine Soon” indicator , refer to the Instrumentation chapter .
The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty . Empty reserve is the small amount of usable fuel remaining in the fuel tank after the fuel gauge indicates empty .
4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple calculations in order to determine fuel economy: Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles traveled by total gallons used.
• Revving the engine before turning it off may reduce fuel economy . • Using the air conditioner or defroster may reduce fuel economy . • Y ou may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs.
• Using fuel blended with alcohol may lower fuel economy . • Fuel economy may decrease with lower temperatures during the first 12–16 km (8–10 miles) of driving. • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain.
• Have the items listed in your Scheduled Maintenance Guide performed according to the specified schedule. The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to the life and performance of your vehicle and to its emissions system.
Please consult your “W arranty Guide” for complete emission warranty information. Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system.
• T urn signals • Backup lamps • License plate lamp Do not remove lamp bulbs unless they will be replaced immediately . If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Replacing headlamp bulbs T o remove the headlamp bulb: 1.
6. W ithout turning, remove the old bulb from the lamp assembly by gently pulling it straight out of the lamp assembly . T o install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass.
2. Open the hood. 3. At the back of the headlamp, pull two retainer pins up to release the headlamp assembly . 4. Pull headlamp assembly forward disengaging the lamp from the rear snap retainers to expose the back of the bulb. 5. Rotate the bulb socket counterclockwise and remove from lamp assembly .
Replacing foglamp bulbs The halogen bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb carefully . Grasp the bulb only by its base. A void touching the glass envelope. 1.
• interior overhead lamp • map lamp For bulb replacement, see a dealer or qualified technician. Map lamps For bulb replacement, see a qualified service technician or your dealer . Using the right bulbs Replacement bulbs are specified in the chart below .
AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician. V ertical aim adjustment 1. Park the vehicle on a level surface approximately 7.
3. On the wall or screen you will observe a light pattern with a distinct horizonal edge of high intensity light. If this edge is not at the horizontal reference line, the beam will need to be adjusted.
Any gasoline spilled on the vehicle or deposits such as bird droppings should be washed and sponged off as soon as possible. Deposits not removed promptly can cause damage to the vehicle’ s paintwork. Remove any exterior accessories, such as antennas, before entering a car wash.
Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately . Cleaning the wheels W ash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents.
Cleaning the wiper blades, windshield and rear window If the wiper blades do not wipe properly , clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent. T o avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents.
• Do not spray with cold water to avoid cracking the engine block or other engine components. • Never apply anything to the drive belt (including belt dressing).
Cleaning seats equipped with side air bags Remove dust and loose dirt with a whisk broom or a vacuum cleaner . Remove fresh spots immediately . Follow the directions that come with the cleaner . Do not saturate the seat cover with upholstery cleaner .
Cleaning leather seats (if equipped) T o clean, simply use a soft cloth dampened with water and a mild soap. W ipe the leather again with a damp cloth to remove soap residue. Dry with a soft cloth. For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer .
MOTORCRAFT PART NUMBERS Component 3.8L OHV V6 engine 4.6L SOHC V8 engine Air filter element F A-1611 F A-1634 Fuel filter FG-800AFG-986 FG-800AFG-986 Battery BXT -59 BXT -59 Oil filter FL-400S FL-820S.
Fluid Ford Part Name Application Capacity T ransmission fluid 3 Motorcraft MERCON t VA T F Automatic with 3.8L OHV V6 engine 13.1L (13.9 quarts) 4 Automatic with 4.6L SOHC V8 engine 12.0L (12.8 quarts) 4 Motorcraft MERCON t AT F Manual with 3.8L OHV V6 engine 2.
LUBRICANT SPECIFICATIONS Item Ford part name Ford part number Ford specification Brake fluid High Performance DOT 3 Motor V ehicle Brake Fluid C6AZ-19542-AB ESA-M6C25-A and DOT 3 Door weatherstrips Si.
1 Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST -M2C118-A for complete refill of T raction-Lok axles. Ford design rear axles contain a synthetic lubricant that does not require changing unless the axle has been submerged in water .
2 5 3 4 1 Capacities and specifications 195.
IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’ s side.
Ford Extended Service Plan Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.
Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to ret.
Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P .O. Box 6248 Dearborn, Michigan 48121 1-800-392-3673 (FORD) (TDD for the hearing impaired: 1-800-232-5952) In Canada: Customer Assistance Centre Ford Motor Company of Canada, Limited P .
• The year and make of your vehicle • The date of vehicle purchase • The current odometer reading • The vehicle identification number (VIN) If you still have a complaint involving a warranty dispute, you may wish to contact the Dispute Settlement Board (U.
What kinds of cases does the Board review? Unresolved warranty repair concerns or vehicle performance as designed concerns on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks wh.
Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm.
• the name of the dealer(s) who sold or serviced the vehicle • a brief description of your unresolved concern • a brief summary of the action taken by the dealer(s) and Ford Motor Company • th.
T o Request a DSB Brochure/Application For a brochure/application, speak to your dealer or write/call to the Board at the following address/phone number: Dispute Settlement Board P .
decisions are fast, fair , and final; the arbitrator’ s award is binding both to you and Ford of Canada. CAMV AP services are available in all territories and provinces, except Quebec. For more information, without charge or obligation, call your CAMV AP Provincial Administrator directly at 1-800-207-0685.
If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMP ANY WORLDWIDE DIRECT MARKET OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.
Ford Deluxe Leather and Vinyl Cleaner (not available in Canada) Motorcraft Vinyl Cleaner (Canada only) Ford Extra Strength T ar and Road Oil Remover* (not available in Canada) Ford Extra Strength Upho.
greater . See your dealer for complete warranty information and availability . Not all accessories are available for all models. V ehicle Security Styled wheel protector locks V ehicle security system.
Cleaners, waxes and polishes Flat splash guards Front end covers (full and mini) Lubricants and oils Molded splash guards Molded vinyl floor mats Seat belt extenders T onneau covers (mini) T ouch-up p.
garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your vehicle’ s operation.) • Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment.
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
Air bag supplemental restraint system ... 75,76 and child safety seats ............. 77 description .............. 76 disposal .................... 80 driver air bag .......... 78 indicator light ...... 9,80 operation ................. 78 passenger air bag .
Cleaning your vehicle ............. 184 engine compartment ......... 187 exterior ........... 185,186 exterior lamps ....... 186 instrument panel .. 188 instrument panel lens .............. 188 interior ............ 189,190 mirrors ...................
Doors lubricant specifications ........ 193 Driving under special conditions through water ....... 115 Emergencies, roadside jump-starting ........ 128 Emission control system ......... 175 Engine ...................... 194 check engine/service engine soon light .
GA WR (Gross Axle W eight Rating) ........ 109 definition ............... 109 driving with a heavy load .......... 109 location .................. 109 GVWR (Gross V ehicle W eight Rating) ........ 109 calculating ............. 109 definition .........
low fuel .................... 11 overdrive off ............ 11 safety belt ................. 8 service engine soon .. 9 traction control active .......... 12 turn signal indicator .................... 8 Load limits ............... 109 GA WR ..........
warning light and chime ............... 8,13,70 Safety seats for children ........... 82,83 Seat belts (see Safety restraints) .................. 65 Seats .......................... 62 child safety seats .................... 82,83 cleaning .......... 189,190 easy access/easyout feature .
W indshield washer fluid and wipers checking and adding fluid ........................ 143 checking and cleaning .......... 159 operation .............
219.
220.
221.
222.
Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity 59.4L (15.7 gallons) Engine oil capacity (includes filter change) 4.7L (5.0 quarts). Use Motorcraft SAE 5W -30 Super Premium Motor Oil, Ford specification WSS-M2C153-G T ire size and pressure See label on inside of glove box door .
3 Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface. 4 Indicates only approximate dry-fill capacity . Some applications may vary based on cooler size and if equipped with in-tank cooler .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Ford 2000 Mustang c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Ford 2000 Mustang - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Ford 2000 Mustang, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Ford 2000 Mustang va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Ford 2000 Mustang, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Ford 2000 Mustang.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Ford 2000 Mustang. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Ford 2000 Mustang ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
