Manuel d'utilisation / d'entretien du produit TID-702NRB du fabricant Farenheit
Aller à la page of 42
OWNER’S MANUAL Mobile V ideo System.
- 1 - T ABLE OF CONTENTS Table of Contents………………………… ………….…………….………………………..1 Safety Information…… …………………………………………….……… ………………2 Features…………………………………………………………….
- 2 - SAFETY INFORMA TION Please read the manual carefully before operating this unit and keep it for future reference. CAUTION: This unit is a class 1 laser product. T o prevent direct exposure to the laser system, do not open the unit. The la ser beam may hurt your eyes.
- 3 - FEA TURES • Motorized Front Panel w/ 4 Pre-Set Angles & Last Angle Memory • Theft Deterrent Detachable Faceplate • Accepts Add-On GPS Navigation Module, NAVIBOX-1 • Accepts Add-On Di.
- 4 - ACCESSORIES Bolt x 1 Back S trap x 1 M5X5 Screws x 4 Keys x 2 Power Wire x 1 Connecter Wire x 1 Connecter Wire x 1 Operational Manual x 1 （ White ） （ Y ellow ） T rim Bezel x 1 Mounting S.
- 5 - WIRE CONNECTION 1. RADIO & ANALOG TV ANTENNA (OPTIONAL) 2. 15PIN SOCKET 3. AUDIO / VIDEO OUTPUT & INPUT 4. NA VI & DIGIT AL TV ADAPTER (OPTIONAL) 5.
- 6 - Brake Control Connect the brake control wire AUTO_ANT (see Wiring Diagram). It is necessary to connect the Brake Control wire to the Hand-brake switch of the car. While driving, the TFT monitor will display the alarm picture (see as follows) in order to ensure the safety .
- 7 - Wiring Diagram.
- 8 - UNIT INST ALLA TION AND REMOVEL Installation Method 1: 1 Install the mounting sleeve 2 Bend the claws into place into the dashboard. to secure the sleeve. 3 Slide the units into the mounting 4 Install the trim bezel onto the unit . sleeve. 5 Install the face p anel onto the unit.
- 9 - Removal Method 1: 1 Detach the face p anel by 2 Detach the trim bezel. pushing the release button. 3 Insert the keys into the aperture 4 Pull the unit out of the between the unit and the mounting mounting sleeve. sleeve to release the internal locks.
- 10 - Installation Method 2: 1 T ighten the bolt onto the rear 2 T i ghten the back strap onto your panel of the unit. car inside the dashboard. 3 Place the unit into the dashboard; 4 Screw the unit on the car on the make the bolt bar across back strap; two sides with M5×5 SCREWS.
- 1 1 - Removal Method 2: 1 Detach the front p anel by 2 Detach the trim bezel. pushing the release button. 3 Unscrew the unit off the car on 4 Unscrew the Nut M5 screw on the rear the two sides. side of the unit and pull out the unit. 5 Sketch map when removal is finished.
- 12 - FRONT P ANEL 1. OPEN/CLOSE/ P. A N G L E 2. REL 3. MENU / NA VI 4. POWER / SOURCE 5. REMOTE 6. AUX IN 7. MIN USB 1. Open/Close/ P. Angle Press the button to open the monitor to eject the disc, press it again to close the monitor.
- 13 - 6. AUX IN Connect an external audio device to this jack to listen to the device through your car speakers. 7. Mini USB The unit will be switched to DVD Mode autom atically when USB connected, and play the songs, pictures, videos in USB. BASE P ANEL 8.
- 14 - REMOTE CONTROL 1. POWER/SOURCE 13. PREVIOUS 25. SYSTEM / NA VI 2. MUTE 14. SLOW / END CALL 26. F. F W D 3. NUMBER BUTTONS 15. TITLE / PBN 27. RIGHT(Seek up) 4. MENU / * 16. ZOOM / CALL 28. STOP 5. AUDIO / # 17. SUBTITLE / PBP 29. D.ANGLE 6. EQ / LOUD 18.
- 15 - 1. [POWER/SOURCE] When ACC is on, press the button to turn the unit on; hold on pressing the button to turn off the unit. When the unit is on, press to switch between different modes. 2. [MUTE] Press to switch off the sound; press it again to resume to the previous volume level.
- 16 - 9. [BAND/ENTER] DVD Mode, press to confirm the selection. Radio Mode, press to switch the wave band as following: FM1 – FM2 - FM3 - AM1- AM2 - FM1 TV Mode, press to switch the TV audio as fol.
- 17 - 20. [VOL+] / 21. [VOL-] Press to increase / decrease the volume. Hold on pressing the button to keep increasing/decreasing the volume. 22. [DISPLAY] Under main menu, press to set the background by default picture. DVD Mode, press to display current playback information.
- 18 - Bluetooth Mode, press to break off o r connect cell phone with the unit. 34. [P/N/AUDIO PLAYER] DVD Mode, press to switch the video output (PAL/NTSC) when playing DVD disc. Bluetooth Mode, press to enter into AUDIO PAIRING. 35. [STEREO/MUSIC PAIR] Radio Mode, press to turn the stereo on / off unde r .
- 19 - T OUCH SCREEN OPERA TIONS TOUCH SCREEN CALIBRA TION When “Power Off”, press the buttons 2, [BAND] of remote control to enter the CALIBRA TI ON page: T o touch the point s from 1 to 5 until the poi nt s change to next cross by using a ballpoint pen or pencil.
- 20 - MAIN MENU 1, T ouch to access the DVD mode. 2, T ouch to access the RADIO mode. 3, T ouch to access the GPS mode. 4, T ouch to access the iPod mode. 5, T ouch to access the AT S C mode. 6, T ouch to access the SD CARD mode. 7, T ouch to access the USB mode.
- 21 - RADIO OPERA TIONS T ouch the [RADIO] icon to access to Radio Mode. 1. Current Source Indicator Display the source currently playing, touch to return the main menu. 2. Mute T ouch to switch off the sound; touch it again to resume to the previous volume level.
- 22 - DVD PLA YER OPERA TIONS 1, T ouch the [DVD] icon to access to DVD Mode if disc inside. 2, The unit will be switched to DVD Mode automatically when inserting the disc. 3, The unit will switch to RADIO Mode automatically if disc ejected. 1. Current Source Indicator Display the source currently playing, touch to return the main menu.
- 23 - 1. Capture Image T ouch to capture the current playing image and store into memory for background or screen saver . 3. Display T ouch to display the current playback information on the screen. 4. Repeat T ouch to repeat as CHAPTER-TITLE-ALL-REPEAT OFF when DVD playback.
- 24 - 2. Setup T ouch to access the DVD SETUP menu. T ouch the [<] / [>] icons to switch the main menus as following: General – S peaker – Dolby Digital – Preference – General T ouch the [ ∧ ] / [ ∨ ] icons to access the submenus from main menus.
- 25 - Screen Saver Select ON or OFF . Last Memory Select ON or OFF . Speaker Setup Page Downmix Following options are available for the Downmix: L T / RT S tereo Off Dolby Digit al Setup Dynamic Following options are available for the Dynamic: FULL 6/8 4/8 2/8 OFF .
- 26 - Preference Page Audio Following options are available for the Audio Language: English French S panish German Danish Swedish It alian Portuguese Polish Korean Russian Dutch Subtitle Following op.
- 27 - IPOD OPERA TIONS (Optional) 1, T ouch the [IPOD] icon to switch IPOD Mode if iPod connected. 2, The unit will switch to IPOD Mode automatically if iPod connected.
- 28 - Video Page Under the Video Page, use the contr oller of iPod itself to control all operat ions of iPod including play music, videos and view pictures. 1. Current Source Indicator Display the source currently playing, touch to return the main menu.
- 29 - A V IN OPERA TIONS T ouch the icon “A V IN” to enter the A V IN Mode: 1. Current Source Indicator Display the source currently playing, touch to return the main menu. 2. Mute T ouch to switch off the sound; touch it again to resume to the previous volume level.
- 30 - NA VI OPERA TIONS (Optional) T ouch Scre en Calibration When 1 st time to enter NA VI mode, you will see the calibration screen. Please touch the points from 1 to 5 by using a ballpoint pen or pencil. T o verify the calibration, please touch the points from 1 to 5 again.
- 31 - The T ouch Screen is restored to their default positions. T ouch anywhere of panel to finish the calibration and go to the following screen: Read information and touch “I agree” button at the bottom of the screen, then enter t he NA VI mode.
- 32 - Go to NA VI mode T ouch the icon “NA VI” to enter the NA VI Mode if NA VI BOX connected: Following screen will be displayed: Read information and touch “I agree” button at the bottom of the screen. Enter the NA VI mode by main menu, the NA VI operations are effective only , all other processes are disable such as Radio, CD etc.
- 33 - Quick Access Key [NA VI] Under any working mode, hold on pressing the [MENU/NA VI] button to switch to NA VI mode; hold on pressing the [MENUNA VI] button again to return the previous working mode.
- 34 - A TSC OPERA TIONS (Optional) 1. Current Source Indicator Display the source currently playing, touch to return the main menu. 2. Mute T ouch to switch off the sound; touch it again to resume to the previous volume level. 3. Return T ouch to return submenu to menu.
- 35 - SYSTEM P ARAMET ERS SETUP T ouch the [SYSTEM] icon to enter the System Parameters Setup. SCREEN SETUP 1. Contrast T ouch [UP] / [DOWN] icons to adjust the CONTRAST parameters (Range: -9 to 9); 2. Ti n t T ouch [UP] / [DOWN] icons to adjust the TINT parameters (Range: -9 to 9); 3.
- 36 - 4. Sub-Woofer V olume T ouch [UP] / [DOWN] icons to adjust the SUB-WOOFER volume parameter (Range: 0 to 15); 5. Buzzer T ouch to turn Buzzer on or off; 6. Balance / Fader T ouch [LEFT] / [RIGHT] icons to adjust the BALANCE parameters (Range: -9 to 9); T ouch [FRONT] / [REAR] icons to adjust F ADER parameters (Range: -9 to 9); 7.
- 37 - 2. Screen Saver Images List T ouch [UP] / [DOWN] icons to select the image of screen saver . 3. Desktop T ouch to set the selected image of captured images list as desktop image. 4. Del T ouch to delete the selected image of screen saver images list.
- 38 - SPEC IFICA TIONS GENERAL Supply V oltage : 14.4V DC (1 1-16V allowed) Load Impedance : 4 Ω per channel Max Power Output : 50W x 4 Bass 100Hz : ≥ 10dB T reble 10KHz : ≥ 10dB Dimensions (approx.) : 183 x 188 x 60 mm (d/w/h) Mounting (approx.
- 39 - TROUBLE SHOOTING If any of problem persists after checking t he below list, Please consult your nearest service dealer. Never attempt to disassemble and repair unit personally.
- 40 - Problem Cause Action TFT MONITOR Reverse circuit not connected Check connections at reverse lamp No video display (when in reverse) Vehicle is not in reverse Select reverse gear Front panel wil.
- 41 - DISC NOTES ■ Disc formats supported by this player Handling and Cleaning ● Dirty, dusty, scratched or warped discs will cause misoperation. ● Do not place stickers or make scratches on discs. ● Do not warp discs. ● A disc should always be kept in its case when not in use to prevent from damage.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Farenheit TID-702NRB c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Farenheit TID-702NRB - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Farenheit TID-702NRB, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Farenheit TID-702NRB va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Farenheit TID-702NRB, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Farenheit TID-702NRB.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Farenheit TID-702NRB. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Farenheit TID-702NRB ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
