Manuel d'utilisation / d'entretien du produit 386SX/16 PLUS du fabricant Epson
Aller à la page of 261
.
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
EPSON ® EQUITY® 386SX/16 PLUS User’s Guide.
IMPORTANT NOTICE DISCLAIMER OF WARRANTY Epson America makes no representations or warranties, either express or implied, by or with respect to anything in this manual, and shall not be liable for any implied warranties of merchantability and fitness for a particular purpose or for any indirect, special, or consequential damages.
1. 2. 3. 4. 5. 6. 7. 8. 9. Important Safety Instructions Read all of these instructions and save them for later reference. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Use a damp cloth for cleaning, not liquid cleaners or aerosol cleaners.
13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power cord or plug is damaged. B. If liquid has entered the product. C. If the product does not operate normally when the operating instructions are followed.
Contents Introduction Optional Equipment ............................... 1 Operating Systems and Other Software ................ 2 VGA Utilities ..................................... 3 How to Use This Manual. ........................... 3 Where to Get Help.
Setting the Primary Display Type ..................... 2-8 Setting the Keyboard Test Function ................... 2-9 Setting the Shadow RAM. ........................... 2-10 Setting the CPU Clock Speed ........................ 2-11 EMS Size .........
Chapter 4 Enhancing System Operations Using AUTOEXEC.BAT and Other Batch Files ........... 4-1 Changing the Processor Speed ....................... 4-2 Entering Keyboard Commands. .................. 4-4 Using the ESPEED Program. ..................... 4-5 Using Expanded Memory Beyond 640KB.
Appendix A Specifications CPU and Memory ................................. A-1 Controllers. ...................................... A-2 Interfaces ........................................ A-2 Power Supply ..................................... A-3 Mass Storage .
Appendix C Performing System Diagnostics Starting the Diagnostics Program ..................... C-2 The Main Menu Screen ............................. C-2 Setting the Run Time Parameters ..................... C-4 Error Logging. .......................
Appendix D Troubleshooting Identifying Your System ............................ Error Messages .................................... The Computer Won’t Start .......................... The Computer Does Not Respond .................... Password Problems .
Introduction The Epson® Equity® 386SX/16 PLUS is a high-performance personal computer which offers exceptional speed and convenience in a compact design.
You may want to install an 80387SX, 16 MHz math coprocessor in your computer to speed up mathematical calculations in certain application programs. Check with your authorized Epson dealer for information on optional equipment. Operating Systems and Other Software You probably have a version of MS-DOS® to use with your computer.
How to Use This Manual This manual explains how to set up and operate your computer, install options, and run diagnostic checks. Although the illustrations show a computer with a 5Mnch diskette drive, instructions for using a 3%inch drive are included.
Appendix C outlines the system diagnostic tests you can run to diagnose hardware problems. Appendix D contains troubleshooting tips. At the end of the manual, you’ll find a glossary and an index.
Chapter 1 Setting Up Your System 1 Setting up your Equity 386SX/16 PLUS personal computer is easy. Just follow the eight steps in this chapter. As you set up your system, you may want to leave this manual’s back cover foldout open so you can refer to the illustrations identifying the different parts.
Before you set up your computer, it’s important to choose a safe, convenient location that provides the following: A sturdy desk or table strong enough to support the weight of your system and all of its components.
2 Removing the Protector Card If you have a 5%inch diskette drive, there is a protector card in the diskette slot. This card is inserted at the factory to protect the read/write heads in the drive. To remove it, flip the latch up to pop the card out part way, as shown below; then pull it out.
3 Connecting a Monitor The way you connect your monitor to the computer depends on the type of monitor you have. If you have a VGA monitor (or a multi-frequency monitor with an analog connector), you can connect it to the computer’s built-in VGA port.
4. Examine the connector end of the monitor cable, and position the plug to match the orientation of the monitor port (marked with a monitor icon). Then insert the plug into the port, as shown below. I Ii i II retaining screws Caution To avoid damaging the connector, take care not to bend the pins when inserting the plug.
6. Plug the monitor power cord into the monitor’s power inlet, as shown below. 7. Plug the other end of the power cord into an electrical outlet. 1-6 Setting Up Your System.
Using a Display Adapter Card If you are using a non-VGA monitor, you’ll need to install a display adapter (video) card in one of the computer’s option slots before you can connect the monitor. (Your dealer may have already installed the video card for you.
Once you have installed your video card, return to this section to connect your monitor to the computer. If your monitor came with its own manual, follow the instructions there. Otherwise, you can follow the steps in “Using the VGA Interface” above; just insert your monitor connector into the video card port instead of the built-in VGA port.
2. One end of the printer cable has a 25-pin, D-shell connector. Position the plug to match the orientation of the parallel interface (marked with a special icon shown in the illustration below).
3. Connect the other end of the cable to the printer as shown below. To secure the cable, squeeze the clips at each side of the printer port and push them into place, 4. Plug the printer’s power cord into a three-hole, 120-volt, grounded electrical outlet.
Using the Serial Interface If you have a printer, a modem, or other peripheral device with a serial interface, you can connect it to the serial (RS-232C) port on the back of the computer. The serial port uses a DB-9P connector, so be sure you have a compatible cable.
Connecting the Keyboard Follow these steps to connect the keyboard: 1. Hold the keyboard cable connector so the indicator on the housing faces up. Insert the plug into the appropriate socket, marked with a keyboard icon, as shown below.
2. You can raise the keyboard by adjusting the legs on the bottom. To change the angle of the keyboard, turn it over and flip each leg upward until it locks into place, as shown below. 6 Connecting the Mouse Your computer has an auxiliary port for an IBM PS/2 compatible mouse that uses a miniature DIN (6-pin) connector.
- ,. mouse connector caution Although the mouse and keyboard connectors are physically identical, they cannot be used interchangeably. Be sure to insert the mouse plug into the mouse port. Once you have connected a mouse, you may need to add commands to your MS-DOS CONFIG.
7 Connecting the Power Cord Follow these steps to connect the power cord: 1. Plug the power cord into the AC power inlet on the back panel, as shown below. WARNING To avoid an electric shock, be sure to plug the cord into the computer before plugging it into the wall socket.
8 Turning On the Computer After you set up your system, you’re ready to turn on the power. But first, read the following safety rules to avoid accidentally damaging your computer or injuring yourself: Do not connect or disconnect any cables when the computer’s power is on.
4. To turn on the computer, press the power button located on the right side of the front panel, as shown below. power button The power indicator next to the button lights up. After a few seconds, the computer counts the amount of memory in your computer, and then performs a diagnostic self test.
When the system has successfully completed its self test, you see the following prompt: Press <Del> to start SETUP Do not press any key yet. If MS-DOS has already been installed on your system, you’ll see a prompt to enter the date. (For information about loading the operating system, see your MS-DOS Installation Guide or Reference Manual.
Chapter 2 Running the SETUP Program When you use your computer for the first time, you need to run the SETUP program to define how your system is set up. This is a simple procedure which you must do at least once. You may need to run it again later if you change some part of your configuration.
The configuration you define through SETUP is stored in a special area of memory called CMOS RAM. This memory is backed up by a battery, so it will not be erased when you turn off or reset the computer.
The menu automatically displays the base memory size, the extended memory size, and whether a math coprocessor (numeric processor) is installed. Additionally, the SETUP menu lists the parameters you can change. Selecting Options A solid cursor bar highlights the parameter currently selected.
Setting the Diskette Drive(s) Your system probably came with one diskette drive installed. You may have added another drive or replaced the existing drive with one of a different size or capacity. The SETUP menu offers five possible selections for your diskette drives (A and B): 3 1.
Setting the Hard Disk Drive(s) The SETUP program lets you select the type of hard disk drive(s) installed in your computer. If you have two hard disk drives, the first one is C and the second one is D. Be sure to choose the correct setting for both drives.
Hard disk drive types 2-6 Running the Setup Program.
Hard disk drive types (continued) Defining your own drive type If the parameters for your hard disk (listed in its documentation) do not match any of the types listed in the table above, you can define your own type.
Press Enter after typing each number. If you enter an invalid number, the computer beeps and does not go on to the next parameter. Check your drive documentation and try again. You do not enter a value for Size; SETUP does this automatically based on the other values you have entered.
Q If you have a composite color monitor, such as a color television with a video input, try selecting Color 80x25. If you find that the monitor’s resolution is poor, run SETUP again and select Color 40x25. If you have two display adapters of different types, select the setting for the one you want to be your primary display adapter.
Setting the Shadow RAM Your computer can access RAM (random access memory) faster than ROM (read-only memory). The Shadow RAM feature enables the Equity 386SX/16 PLUS to copy the contents of its system BIOS and/or video ROM into RAM so it can perform certain operations faster.
Setting the CPU Clock Speed This option lets you set the default speed at which your computer’s processor operates when you turn it on: U High speed (16 MHz) U Low speed (8 MHz) U Auto speed. When it is running at high speed, the TURBO light on the front panel is illuminated.
EMS Size The EMS Size option provides a simple way to set the amount of memory you want to use as expanded. Expanded memory can be used by application programs conforming to the Lotus/Intel®/Microsoft® Expanded Memory Specification (LIM EMS). The Equity 386SX/16 PLUS is compatible with version 4.
For example, with 2MB of memory, you can specify any of the following as expanded memory: tl 0KB 0 256KB Cl 512KB Cl 768KB CL 1024KB CI 1280KB. Setting the Password The SETUP program lets you set an optional password to control who can use your system.
Now type the password you want to use. You can type up to eight characters using the letter or number keys, in upper- or lowercase. For example, you could enter the following: 123aBc! You can use the backspace key to correct mistakes. After you type the password, press Enter.
Setting the Built-in Interfaces This option lets you define how the following built-in interfaces operate: 0 Parallel port (LPT1, LPT2, LPT3) U Serial port (COM1 or COM2) Q Hard disk drive controller (HDC) tl Floppy disk drive controller (FDC). Setting the Parallel Interface The built-in parallel port is set to act as the primary (LPT1).
Setting the Serial Interface The built-in serial port in your computer is set to act as the primary port (COM1). If you install an option card that provides an additional serial port, that port automatically becomes secondary (COM2). However, if you want the port on the card to be COM1, select COM2 for the built-in port.
If you saved your changes, the SETUP program resets your system and the computer runs through its power-on diagnostic tests. If something is wrong, however, you see an error message and a prompt to run SETUP. Follow the instructions on the screen to run SETUP again to correct it.
2-18 Running the Setup Program.
Chapter 3 Using Your Computer This chapter briefly describes the following procedures for using your computer: U Installing MS-DOS or another operating system CI Using special keys on the keyboard Cl Stopping a command or program U Resetting the computer 2 Using a password U Using disks and disk drives.
Special Keys on the Keyboard Certain keys on your keyboard serve special functions when your computer is running MS-DOS or application programs. The special keys are described in the table below. Special key functions Key Purpose Tab It Tab -+I Moves the cursor one tab to the right in normal mode and one tab to the left in Shift mode.
Special key functions (continued) Key Num Lock Purpose Changes the function of the numeric/cursor keys from entering numbers to positioning the cursor; changes back when pressed again. Esc F1-F12 Print Screen S YS Rq Cancels the current command line or operation.
These methods may also work in your application program. If not, you may need to reset the computer, as described below. Caution It is best not to turn off the computer to stop a program or command. If you created new data and have not yet stored it, the data will be erased if you turn off the computer.
There are two ways to reset the computer: 3 If you are using MS-DOS, hold down Ctrl and Alt and press the Del key. The screen goes blank for a moment and then the computer should reload MS-DOS. If it doesn’t, try the next method. Q Press the RESET button on the front panel.
If you do not enter the correct password the first time, press Enter and try again. If you want to change or delete your current password, you must run the SETUP program. See Chapter 2 for instructions. Using Disks and Disk Drives The disk drives in your computer allow you to store data on disk, and then retrieve and use your stored data.
All disks are divided into data storage compartments by sides, tracks, and sectors. Double-sided diskettes store data on both sides. On each side are concentric rings, called tracks, on which a disk can store data. A disk is further divided by sectors, which are similar in shape to pie slices.
Your computer uses the read/write heads in a disk drive to store and retrieve data on a disk. To write to a disk, the computer spins it in the drive to position the disk so that the area where the data is to be written is under the read/write head. A diskette has an exposed area where the read/write head can access it.
0 360KB drive-Use 5%inch, double-sided, double-density, 48 TN, 360KB diskettes. (You can also use single-sided, 160KB or 180KB diskettes.) These diskettes contain 40 tracks per side and 8 or 9 sectors per track. With 8 sectors per track, a diskette holds up to 320KB.
Because of these incompatibilities, always indicate the diskette type and density when you label your diskettes. (Usually this information appears on the manufacturer’s label.
cl 0 cl Ll Keep diskettes in a moderate environment. Don’t leave diskettes sitting in the sun, or in extreme cold or heat. Keep diskettes away from magnetic fields, such as electrical appliances, telephones, and loudspeakers. (Remember that diskettes store information magnetically.
Write-protecting Diskettes You can write-protect a diskette to prevent its data from being altered. When a diskette is write-protected, you can read it and copy data from it, but you cannot store new data on it or delete any files it contains. If you try to change data stored on a write-protected diskette, MS-DOS displays an error message.
On a 3%inch diskette, the write-protect device is a small switch on the back of the diskette in the lower right corner, shown below. To write-protect a 3%?-inch diskette, slide the switch toward the edge of the diskette until it clicks into position, exposing a hole in the corner.
Using a Single Diskette Drive System MS-DOS expects the computer to have at least two diskette drives and displays prompts and messages accordingly. Usually, MS-DOS recognizes the first diskette drive (the top drive) as A and a second diskette drive as B.
Inserting and Removing Diskettes If you have a 5%inch diskette drive, insert a diskette as follows: hold the diskette with the label facing up and the read/write slot leading into the drive, as shown below. rite slot Slide the diskette into the slot until it is in all the way.
If you have a 3 1/2-inch diskette drive, insert the diskette with the label facing up and the metal shutter leading into the drive, as shown in the following illustration.
Formatting Diskettes Before you can store data on a new diskette, you must format it using the FORMAT command. Formatting prepares the diskette so that MS-DOS can write data on it. You need to do this only once, before you use the diskette for the first time.
Using a Hard Disk Drive Using a hard disk is similar to using a diskette. However, the hard disk provides several advantages: Q A 40MB hard disk can store as much data as approximately thirty-three 1.2MB diskettes, and a 100MB hard disk can store as much data as approximately eighty-two 1.
Caring for your hard disk drive Follow these precautions to protect your hard disk drive from damage and to avoid losing data: Ll Never turn off or reset the computer when the hard disk access light is on. This light indicates that the computer is copying data to or from the hard disk.
You see a message on the screen that tells you the disk drive’s read/write heads will remain locked until you reset the computer or turn the power off and on again. The computer locks the heads and disables the keyboard. Remove any diskettes and turn off the computer.
Chapter 4 Enhancing System Operations This chapter tells you how to use the following procedures to enhance the operation of your computer: CI Using AUTOEXEC.BAT and other batch files Ci Changing the processor speed Q Using expanded memory beyond 640KB c3 Using the VGA utilities.
When you install MS-DOS, it creates an AUTOEXEC.BAT file for you. To modify the file or replace it with a new one, you can use the COPY or EDLIN command, a text editor, or a word processing program that can save a file as a text-only file. However, be sure to name the file AUTOEXEC.
There are different types of copy-protected programs. Depending on the type you have, you may or may not want to set the processor to automatic speed. Follow these guidelines: 0 If you are using a copy-protected program that can run only on a diskette or that requires a key disk, try to start the program on high speed.
Entering Keyboard Commands You can change the processor speed by entering one of the commands shown in the following table. Speed setting commands ni To enter these commands, hold down the Ctrl key and the Alt key simultaneously and then press the 2, +, 1, or - key.
Using the ESPEED Program ESPEED provides an easy way to change the processor speed if your application program does not recognize the Ctrl keyboard commands or if you want to include the program command in a batch file. The ESPEED program is provided with your system on the Reference diskette.
To display the current CPU speed, type ES P E ED only and press Enter. You see the following: <+> : Speed Up 16.0 MHz <-> : Speed Down <Esc> : Exit To change the speed when you see this display, press the + or - key; then press Esc to exit.
Using Expanded Memory Beyond 640KB The Equity 386SX/16 PLUS comes with 2MB of random access memory. MS-DOS and your application programs that run under MS-DOS use the first 640KB of memory. You can use any memory above 1MB as extended memory (up to 16MB) or expanded memory (up to 24MB).
3. Add a command to the CONFIG.SYS file to include the memory manager as a device driver, as described in the next section. The CONFIG.SYS file is used by MS-DOS to set up the computer’s system configuration requirements.
3. Save the file as an ASCII text file. 4. Reset the computer. If you do not have a word processing program capable of saving an ASCII text file, you can modify CONFIG.SYS using the MS-DOS EDLIN or COPY CON command, or a text editor. See your MS-DOS Reference Manual for instructions.
The M[n] parameter specifies a particular 64KB page frame address for EMM386SX.SYS. The value n must be a number from 1 to 9 to indicate one of the following addresses: 1 2 3 4 5* 6 7 8 9 0C0000h 0C40.
EMM386SX.SYS automatically excludes from mapping any addresses that are reserved for use by your system ROM and RAM. If you install an option card, such as a network card, that uses the memory address range C000 through E000, include the X parameter in the DEVICE= command line to exclude this memory range from expanded memory mapping.
You can use the VGA utilities (also provided on the Utility diskettes) to take advantage of other special features of your VGA adapter. Even if you do not use any device drivers, you may want to install some of the VGA utilities, such as the following: VGAMODE Provides 132-column text in text-based programs such as Wordstar® and WordPerfect®.
Chapter 5 Installing and Removing Options You can enhance the performance of your computer by adding a variety of options, including the following: 0 Option cards Q Memory modules Q A math coprocessor. An option card is a circuit board you install in your computer to add a particular function.
A math coprocessor speeds up the numeric calculations your computer performs when using certain application software. If you purchase a math coprocessor, it is a good idea to ask your dealer to install it for you, because it can be damaged easily. If you decide to install it yourself, follow the appropriate steps in this chapter.
4. 5. Turn the computer around so you are facing the back panel. The cover is secured by a large screw on the back panel, as shown below. Turn the screw counterclockwise to unlock the cover. The cover is also secured by two latches on the back of the cover near the corners.
6. Pull the cover away from the front of the computer to completely remove it. Then set it aside. 7. Before you touch any of the components, touch the inside of the computer’s back panel, as shown below, to ground yourself and avoid an electric shock.
Changing the Jumper Settings If you change your computer’s configuration or need to alter the way it operates, you may need to change a jumper setting inside the computer. A jumper is a small electrical connector that controls one of the computer’s functions.
Setting the Jumpers The illustration below shows the locations of the jumpers on your computer’s main system board. II i II IIll ____............. ill I . . . . . . . . . . . . . . . . . - . .._.._..___.______. A jumper’s setting is determined by where the jumper is placed on the pins.
The following table lists the jumper settings and their functions. Main system board jumper settings A B* A B* A* B A* B * Factory setting Disables the built-in VGA display adapter so you can use a di.
If you need to change any jumper settings, follow these steps: 1. Remove any option cards that may be blocking your access to the jumpers. See page 5-16 for instructions. 2. Change the jumper settings. 3. Replace any option cards you removed. See “Installing an Option Card” on page 5-12.
If necessary, follow the instructions on page 5-2 to remove the computer’s cover. Then follow these steps to replace the battery: 1. Turn the computer so that the front panel is facing you. The battery is attached to the bottom of the computer case, just behind the front panel, as shown below.
2. 3. The battery is attached to the computer with Velcro? Remove the battery by pulling it up from the bottom of the computer case, as shown below. Then set it aside. -- Remove the new battery from its package and position it so the Velcro faces down and the cable faces connector CN1.
4. Connect the battery cable to connector CN1. battery cable connector CN1 5. Follow the steps on page 5-40 to replace the computer’s cover. Then run the SETUP program to reconfigure your system and reset the time for the real-time clock. See Chapter 2 for instructions.
Installing an Option Card Your computer has four standard option slots: three 16-bit slots and one 8-bit slot. Each slot can accommodate an option card. You can buy option cards from authorized Epson dealers as well as other vendors. This section explains how to install option cards in your computer.
Slots 1 through 3 are designed for 16-bit option cards and slot 4 is designed for an 8-bit card. As you can see below, a 16-bit card has an extra connector along the bottom. 16-bit option card 8-bit option card Usually it does not matter which slot an option card occupies as long as the card fits in the slot.
Follow these steps to install an option card: 1. If you have not already done so, remove the cover from the computer. (See page 5-2 for instructions.) WARNING After you remove the cover, touch the inside back panel of the computer to ground yourself and avoid an electric shock.
4. Unpack the option card and adjust any switches or jumpers on it, if necessary. (Check the option card instructions.) When you handle the card, be careful not to touch any of the components on the circuit board or the gold-edged connectors.
7. Secure the end of the card to the back of the computer with the retaining screw. 8 8. Follow the instructions at the end of this chapter to replace the cover. Then see “Post-installation Setup,” following that section. Removing an Option Card If you need to remove an option card, follow these steps: 1.
4. If you are removing an option card that controls a mouse, you need to change the setting of jumper J4 on the main system board. If you are removing a display adapter card, you may need to change the settings of jumpers J1, J3, and J5. See page 5-7 for instructions.
Follow these steps to remove the subassembly: 5-18 1. Remove the front panel from the computer by lifting up slightly on the three clips at the top of the panel and tilting it toward you.
3. 4. Grasp the connector and pull it straight up to remove it from the socket. Do not pull only on the cable. The diskette drive cable is connected to the socket behind the hard disk drive socket; disconnect it in the same manner.
5. Raise the front of the subassembly, as shown below. 6. Reach back underneath the subassembly and disconnect the two power supply cables connected to the right side of the main system board, as shown below. Pull each connector straight up. Do not pull only on the cables.
7. Lift the entire subassembly out of the computer and carefully place it on your work surface. Adding Memory Modules Your computer comes with 2MB of memory soldered directly onto the main system board. By installing SIMMs (single inline memory modules), you can increase the memory in your computer up to 24MB.
Installing Memory Modules There are six SIMM sockets on the main system board organized in three banks consisting of two sockets each. The sockets are labeled SIMM1 through SIMM6. The following table shows all the possible SIMM configurations for your computer.
Follow these steps to install SIMM: 1. Remove the computer’s cover. See page 5-2. 2. Remove the subassembly. See page 5-17. 3. The SIMM sockets are located on the front of the main system board near the math coprocessor socket, as shown below.
4. Install the SIMMs in the sockets closest to the right side of the main system board first. Position each SIMM so the notch on its edge faces the front of the computer and place it on the left side of the tabs at an angle, as shown below.
6. 7. 8. The SIMM should snap into place between the tabs and the retaining posts. If it does not go in smoothly, do not force it; pull it all the way out and try again. Make sure the SIMM is fully inserted into the socket and that the pins on the retaining posts extend through the holes in both ends.
3. The SIMM sockets are located on the front of the main system board near the math coprocessor socket, as shown below. SIMM sockets . A a ‘IMM3 SIMM4 SIMM6 SIMM1 1 SIMM2 math coprocessor socket 5-2.
4. Remove the SIMMs in the sockets closest to the left side of the main system board first. Use your fingers or two small screwdrivers to pull away the tabs that secure the SIMM at each end. Be careful not to pull the tabs too far, or they may break. As you pull away the tabs, the SIMM falls to the left.
Installing a Math Coprocessor Your computer has a socket on the main system board to accommodate an 80387SX, 16 MHz math coprocessor. A math coprocessor speeds up your computer’s numeric calculations and graphic image displays when you are using certain application software.
4. The math coprocessor socket is located on the front of the main system board near the SIMM sockets, as shown below. math coprocessor socket 5. The math coprocessor socket is hollow and square, and has a notch in the lower left corner, as shown below.
6. 5-30 The math coprocessor also has a notch in one corner, marked by a dot, as shown below. notch r5 J 0 0 A80370X-16 SX106 L9450188 INTEL@@ 1986 a 0 .
If the coprocessor does not go in smoothly, do not force it; pull it all the way out and try again, keeping it straight as you insert it. It is completely inserted when the surface of the coprocessor is flush (even) with the surface of the socket. Be sure it is inserted all the way.
Replacing the Subassembly Follow the steps below to replace the subassembly inside your computer: 1. Notice that there are four mounting slots on the back of the subassembly: two in the upper corners and two in the lower corners.
There are four corresponding tabs on the inside back panel of the computer which fit into the openings in the subassembly slots. tabs Lift up the subassembly from your work surface and lower the back end into the computer, guiding the top slots on the subassembly into the top tabs on the computer.
2. Hold up the front of the subassembly at a slight angle and arrange the ribbon cables so they curve underneath the subassembly and extend out its left side. Then grasp the two power supply cables, labeled P4 and P5. Each connector has six pin holes and a large tab on one side, as shown below.
3. Position power supply connector P4 so the large tab on the connector faces the right side of the computer. Beginning with the six pins toward the back of the computer, carefully line up the holes in the connector with the pins in the socket and then push in the connector.
5. Carefully lower the front of the subassembly onto the computer. Make sure that all four tabs on the back of the computer are inserted into the slots on the subassembly as you lower it.
Guide the tabs on the front of the subassembly over the opening in the front of the computer so the two small tabs sit behind the opening and the large tab with the curved lip sits over the front of the opening. If necessary, press on the large tab until the subassembly snaps into place.
Both the diskette drive and hard disk drive sockets are located on the main system board on the left side of the subassembly, as shown below. diskette drive socket hard disk drive socket subassembly --El- Both sockets have a notch on one side. Connect the diskette drive cable first.
Align the connector with the socket so the tab on the connector lines up with the notch in the socket. Make sure the holes in the connector fit over all the pins in the socket and then push in the connector. Caution If you do not correctly align the holes with the pins, you could severely damage your computer when you push in the connector.
Replacing the Cover Follow these steps to replace the computer’s cover: 1. Facing the back of the computer, hold the cover so that the side with three tabs on the edge faces away from you, as shown below. tabs 2. Insert the three tabs into the three notches in the back of the front panel of the computer.
3. Lower the back of the cover onto the computer and press down firmly on all edges of the cover to form a tight seal. 4. Turn the large screw on the back panel clockwise to secure the cover to the computer. 5. Reconnect the computer to the monitor, printer, keyboard, and any other peripheral devices you have.
U If you want to use any of the memory on your card as expanded memory, see “Using Expanded Memory Beyond 640KB” in Chapter 4. Also see “Post-installation Setup,” below, for more information on setting up your computer for use with an option card.
If you install an optional memory card, use the setup program that comes with it to configure the computer for use with the card. See your memory card manual for instructions. Additionally, you may need to add some commands to your configuration files.
5-44 Installing and Removing Options.
Appendix A Specifications CPU and Memory 16-bit CPU System memory ROM Shadow RAM Math coprocessor (optional) Clock/calendar Battery 80386SX microprocessor, 16 MHz system clock speed, 16 MHz or 8 MHz p.
Controllers Diskette Hard disk Interfaces Monitor Serial Parallel Mouse Keyboard Option slots Speaker Supports up to two drives in any of four formats: 5Wnch, high-density, 1.
Power Supply Type Input ranges Maximum outputs Mass Storage Diskette drives Hard disk drives Other devices 145W, fan-cooled 98 VAC to 132 VAC, 47 Hz to 63 Hz +5 VDC at 18 Amps, +12 VDC at 4.
Keyboard Layout Detachable, two position; 101 sculpted keys 58-key QWERTY main keyboard; 17-key numeric/cursor pad; 10 cursor keys; additional 4-key cursor pad; 16 function keys (user-definable) Funct.
System Memory Map OOOFFFFFFh 000FF0000h 000FE0000h 00100000h 000F0000h 000E0000h 000C8000h 000C0000h 000A0000h 00000000h System BIOS ROM: 64KB Duplicated from 0F0000h Reserved for system board: 64KB D.
A-6 Specifications.
Appendix B Installing and Removing Disk Drives This appendix describes how to do the following: Ci Install a hard disk or diskette drive Q Remove a hard disk or diskette drive D Change the hard disk drive jumper settings.
Caution Installing or removing a disk drive is a complicated procedure, so you may want to ask your dealer to do it for you. If you decide to do it yourself, you must carefully follow all the instructions in this appendix or you could damage your equipment.
How to Use This Appendix The instructions in this appendix describe how to install and remove optional Epson diskette and hard disk drives. All drives sold by Epson for the Equity 386SX/16 PLUS are qualified and recommended for use in this system.
Setting the Hard Disk Drive jumpers You need to check or change the jumper settings on the hard disk drive if you are installing or removing any hard disk drives.
Changing the Jumper Settings The hard disk drive jumpers are located on the drive’s circuit board, near the large cable connector. cable connector The jumpers on your drive may be in a slightly different location, but you set them the same way. There are four positions for the jumpers on each hard disk drive.
The following table lists the jumper settings for all the possible hard disk drive configurations. Jumper One hard positions disk drive HSP C/D X DSP - ACT X Two hard disk Two hard disk drives: master.
If one of your hard disk drives is already installed in the computer, follow the steps under “Removing a Hard Disk From the Vertical Position” on page B-24 to remove it. Then set the jumpers on both drives while they are out of the computer. The steps in that section tell you which instructions to follow next.
Removing the Mounting Frames From the Drive Your hard disk drive comes with 5 N-inch mounting frames attached to each side of the hard disk drive, as shown below.
On one side, there may also be a plastic guiderail. Follow these steps to remove the mounting frames (and guiderail) from the drive: 1. If necessary, remove the screws securing the plastic guiderail and the metal grounding plate to one of the mounting frames, as shown below.
Keep the four screws so you can use them to secure the mounting plate to the hard disk drive. Then set the drive aside with the component side facing up. Removing and Attaching the Mounting Plate If you are installing a new hard disk drive in your computer, you need to attach a hard disk drive mounting plate to the drive.
2. Remove the screw securing the mounting plate to the computer and set it aside. Then lift up the mounting plate to remove it. , retaining screw I--- 3. Turn your hard disk drive so the components are facing up and the connectors at the back of the drive are facing to the right.
Then place the flat side of the mounting plate on the hard disk drive and align the four holes on the plate with the four holes on the drive, as shown below. mounting plate holes comp connectors 4. Locate the four screws that you removed from the S?Mnch mounting frames and use them to secure the mounting plate to the hard disk drive.
The connector at one end of the cable has two rows of holes, one of which is blocked with a plug, as shown below. The ribbon cable socket on the back of the drive has two rows of pins.
Align the connector with the socket so that the row in the connector with the blocked hole lines up with the row in the socket with the missing pin, as shown below.
3. Locate one of the power supply cables that lead from the power supply in the computer (behind the horizontal drive bays). The cables are labeled P1, P2, and P3; you can use any one.
Make sure the holes fit over all the pins and then push in the connector. 4. Pick up the hard disk drive and hold it above the vertical mounting area so the mounting plate is facing the subassembly, as shown below. Connectors mounting plate sembly Notice that there are two tabs facing downward on the bottom of the mounting plate.
5. As you lower the drive into the vertical mounting area, guide the ribbon cable underneath the drive. hole - tabs in slots As shown above, fit the tabs on the mounting plate into the slots on the side of the subassembly.
Connecting the Hard Disk Drive Cables Follow these steps to lift up the subassembly and connect the drive cable to the main system board: 1. Remove the front panel from the computer by lifting up slightly on the three clips at the top of the panel and tilting it toward you.
3. Raise the front of the subassembly to a slight angle, as shown below. Installing and Removing Disk Drives B-19.
4. Use one of your hands to hold up the subassembly or have someone do it for you. With your other hand, grasp the hard disk drive ribbon cable that you tucked beneath the subassembly. Pull the cable under the subassembly all the way to its left side.
Guide the tabs on the front of the subassembly over the opening in the front of the computer so that the two small tabs sit behind the opening and the large tab with the curved lip sits over the front. If necessary, press on the large tab until the subassembly snaps into place.
Pick up the hard disk drive cable and notice the connector on the end of the cable. There is a tab on one side of the connector, as shown below. tab Pull the cable over toward the socket and fold it to align the connector with the socket. Make sure the side of the connector with the tab lines up with the side of the socket with the notch.
7. To replace the front panel, fit the three ridged tabs on its bottom edge into the three notches on the lower edge of the computer, as shown below. tabs 8. Tilt up the front panel until the clips on the top touch the computer. Then push on the top of the panel until it clicks into place.
Removing a Hard Disk From the Vertical Position 1. Turn the computer so that the front panel is facing you. The vertically mounted drive is attached to the right side of the subassembly, as shown below.
2. Remove the retaining screw securing the hard disk drive mounting plate to the computer and set it aside. 3. Tilt the hard disk drive slightly to the right, away from the subassembly, and lift it out of the vertical mounting area. Turn it over and set it on top of the subassembly with the gray mounting plate facing up.
4. Disconnect the power supply connector from the socket on the back of the hard disk drive, as shown below. Firmly pull the connector straight out of the socket so you do not bend the pins. Do not pull too hard on the cable; pull on the plastic connector, if possible.
7. Remove the hard disk drive ribbon cable from its socket on the main system board (near the left side of the subassembly). Store the cable along with the drive. 8. Wrap the hard disk drive in its original packing materials and set it aside. Then carefully arrange the power supply cable so it does not interfere with any other cables or mechanisms.
Removing the Subassembly Follow these steps to remove the subassembly: 1. Turn the computer so that the front panel is facing you. 2. To remove the front panel, lift up slightly on the three clips at the top of the panel and tilt it toward you, as shown below.
3. Place the front panel face down and remove the screws securing the slot cover to the panel. Lift out the slot cover, as shown below. Set the front panel, slot cover, and screws aside. 4. The hard disk drive cable is connected to the main system board on the left side of the subassembly, as shown below.
5. The diskette drive cable is connected to the socket behind the hard disk drive socket; disconnect it in the same manner. 6. The subassembly is the large metal casing enclosing the horizontal drive bays and the power supply, as shown below. To remove the subassembly, first lift it up from the front only.
7. Lift up the front of the subassembly with your thumbs. Raise it to a slight angle, as shown below. Installing and Removing Disk Drives B-31.
8. Reach back underneath the subassembly and disconnect the two power supply cables connected to the right side of the main system board, as shown below. Pull each of the connectors straight up; do not pull only on the cables. power supply cables I 9.
Installing a Disk Drive in the Horizontal Position Before you perform the following steps, be sure that you have set the jumpers on any hard disk drive(s) that you’ll be using. (If not, see “Setting the Hard Disk Drive Jumpers” on page B-4 for instructions.
2. There are two or three holes on each side of the disk drive. When you insert the drive, align the appropriate round holes in the drive with the two oval holes on each side of the drive bay, as shown below. 3. Insert the drive in the lower drive bay and slide it toward the back of the subassembly.
4. Locate the four retaining screws that came with your disk drive, Insert two screws into the oval holes on each side of the drive bay and tighten them with a screwdriver, as shown below. screws If you are installing a diskette drive, go to step 5. If you are installing a hard disk drive, go to step 6.
The interface that protrudes from the back of the drive has gold contacts on both sides. Near one end of the interface, there is a gap to accommodate the plastic divider on the connector. Align the connector with the interface so that the plastic divider on the connector lines up with the gap in the interface, as shown below.
6. Locate the hard disk drive ribbon cable that you removed from the drive in the vertical mounting position. Follow the instructions below to attach the connector on the end of this cable to the drive that will be mounted vertically. As shown below, there are two rows of holes in the connector.
Align the connector with the socket so that the row in the connector with the blocked hole lines up with the row in the socket with the missing pin, as shown below. Make sure the holes fit over all the pins and then push in the connector. If you will have two hard disk drives in your system, perform the procedures in steps 6 and 7 again.
8. Looking at the subassembly, locate one of the power supply cables that lead from the power supply (behind the horizontal drive bays). The cables are labeled P1, P2, and P3; you can use any one. As shown below, the end of the connector has two notched corners.
Position the power supply cable connector so that the notched corners on the connector line up with the notched corners of the power supply socket on your drive.
Replacing the Drive on the Subassembly This section describes how to reinstall your hard disk drive in the vertical mounting position. The following illustrations show the subassembly installed inside the computer with the front panel attached.
2. Lower the drive into the computer, fitting the tabs on the mounting plate into the slots on the side of the subassembly, as shown below. Guide the ribbon cable underneath the drive as you lower it. br hole tabs in slots 3. Tilt the drive toward the subassembly and align the retaining screw hole on the mounting plate with the hole in the bracket.
Removing a Disk Drive from the Horizontal Position The figures in this section show a diskette drive in the lower horizontal drive bay, but you can use the same instructions to remove a hard disk drive from the lower bay or to remove a diskette drive from the upper bay.
power supply cable 3. Using a screwdriver, remove the screws securing the drive to the drive bay. There are two screws on each side, as shown below. screws B-44 Installing and Removing Disk Drives.
4. Grasp the disk drive from the front of the drive bay, pull it completely out, and set it aside. 5. If you have removed one hard disk drive and are leaving another one in your system, make sure you have set the jumpers on the remaining drive to indicate that you now have only one hard disk drive.
Replacing the Subassembly Follow the steps below to replace the subassembly inside your computer: 1. Notice that there are four mounting slots on the back of the subassembly: two in the upper corners and two in the lower corners.
There are four corresponding tabs on the inside back panel of the computer which fit into the openings in the subassembly slots. Lift up the subassembly from your work surface and lower the back end into the computer, fitting the top tabs in the computer into the openings in the top slots on the subassembly.
3. Reach under the subassembly and grasp the two main system board power supply cables, labeled P4 and P5. Each connector has six pin holes and a large tab on one side, as shown below. There is one 12-pin power supply socket on the right side of the main system board (toward the back) that holds both of the power supply connectors, as shown below.
4. Position power supply connector P4 so the large tab on the connector faces the right side of the computer. Beginning with the six pins toward the back of the computer, carefully line up the holes in the connector with the pins in the socket. Make sure the holes fit over all six pins and then push in the connector.
6. Carefully lower the front of the subassembly onto the computer. Make sure that all four tabs on the back of the computer are inserted into the slots on the subassembly as you lower it.
Guide the tabs on the front of the subassembly over the opening in the front of the computer so the two small tabs sit behind the opening and the large tab with the curved lip sits over the front of the opening. If necessary, press on the large tab until the subassembly snaps into place.
8. Both the diskette drive and hard disk drive sockets are located on the main system board on the left side of the subassembly, as shown below. diskette drive socket hard disk drive socket subassembly Both sockets have a notch on one side. The hard disk drive socket is a bit longer than the diskette drive socket.
Connect the diskette drive ribbon cable first. As shown below, there is a tab on one side of the connector. diskette drive connector tab diskette drive socket notch Align the connector with the socket so that the tab on the connector lines up with the notch in the socket.
10. To replace the front panel, fit the three ridged tabs on its bottom edge into the three notches on the lower edge of the computer, as shown below. tabs 11. Tilt up the front panel until the clips on the top of the panel touch the computer. Then push on the top of the panel until it clicks into place.
Appendix C Performing System Diagnostics This appendix describes how to use the System diagnostics program to test the condition of your computer’s main unit and peripheral devices.
Starting the Diagnostics Program To start the diagnostics program, follow these steps: 1. Insert the Reference diskette in drive A and turn on or reset the computer. 2. When you see the following prompt, press the Del key: Press <Del> to start SETUP 3.
When you select a test category from the option line at the top of the menu, you see a submenu of the available diagnostic tests. For example, the submenu for the System board category appears when you first see the main menu because the System board option is selected.
Setting the Run Time Parameters The tests you select will run in the following manner unless you change the run time parameters: 0 Each test is performed one time (passbound) tl The program waits if an error occurs D No errors are recorded to the printer, disk, or other device.
Press N and Enter if you want the diagnostics program to continue when an error occurs. The next option is: Error logging (Y/N) ? N Press Y and Enter to record the errors that may occur during the test. See “Error Logging,” below, for details. Press N and Enter if you do not want to create the log.
If you selected Passbound testing, you see this prompt: No. of passes : 00001 Specify the number of times (from 1 to 65535) you want the program to run the test(s). Or press Enter without entering a number to select the default of one pass. You can use the backspace key to make corrections.
If you select Log errors on d i s k, the program displays this submenu: Floppy disk A: Floppy disk B: Hard disk C: Hard disk D: (You do not see drive D unless you have a second hard disk drive.) Press .L or ? to highlight the disk on which you want to log the error messages and press Enter.
Selecting Diagnostic Tests To start a single test, press + or t to highlight the test category on the main menu. Then press 3. or ‘? to highlight the particular test in the submenu and press Enter to run it. When a test has been completed, you see this prompt: Press <Enter> to return to Main menu.
You can stop testing at any time and return to the main menu by holding down Ctrl and pressing Break. The program completes the current test before it stops. You must enter certain parameters to run the hard disk and diskette drive tests. If you use F3 to select these tests, the program prompts you for the parameters immediately.
Running the Tests The table below lists all of the available System diagnostic tests and refers you to other sections in this chapter for additional information, if necessary.
System diagnostic tests (continued) Component Tests Hard disk Hard disk format drives Media analysis Performance Seek Read/verify Check test cylinder Force bad tracks Function See “Hard Disk Diagnos.
System diagnostic tests (continued) Video 640 x 350 graphics* (continued) 640 x 480 graphics* Misc. Printer adapter See “Miscellaneous Comm. adapter Diagnostics” Test the 640 x 350 graphics display Test the 640 x 480 graphics display * Test appears only if you have installed a color monitor.
Format Media analysis Force bad tracks Performance Seek Read/verify Check test cylinder Before performing any destructive test, the program displays the following messages: WARNING All data on hard disk you have specified may be lost... Do you still want to continue (Y/N)? Press Y and Enter to begin the test.
Disk drive identifier The program displays this prompt for the disk drive identifier: Disk drive (C/D) ? C If only one hard disk is connected to the computer, the program assumes it is drive C and does not display this prompt.
Bad track list Entering the bad track list is optional. The program displays the following prompt for the bad track list: Mark bad tracks (Y/N) ? N You do not need to enter a bad track list for the hard disk that comes with the Equity 386SX/16 PLUS. Press N, if necessary, and then press Enter.
Enter the first and last cylinder numbers on which you want to perform the tests. The default for the start cylinder number is 0, and the default for the end cylinder number is one less than the highest cylinder number of your hard disk. For example, on the 40MB hard disk, the highest cylinder number is 976.
You may want to reformat a hard disk if you have a serious problem with the drive. However, before formatting a disk with data on it, try every other recovery procedure described in your MS-DOS Reference Manual. Then back up all the data on the disk before you begin.
Performance Test This test checks the performance of your hard disk by determining the data transfer rate and track-to-track seek time based on the transfer size, the seek count, and the amount of data transferred. The program measures the data transfer rate in kilobytes per second.
Check Test Cylinder This test checks the test cylinder, which is the last cylinder on the hard disk. You should perform this test if you receive a hard disk error when you boot the system. Force Bad Tracks Use this test to mark bad tracks on the hard disk without formatting it.
The controller displays one of the following messages when an error occurs during a diagnostics procedure: Address mark not found Attachment failed to respond Bad ECC on disk read Bad sector flag dete.
Performing the Tests The Diskette format test checks the format capability of the diskette drive and its controller. In order to run the test, you need a blank diskette that has been formatted using the MS-DOS FORMAT command and that is not write-protected.
Note Be sure to insert a blank diskette that has been formatted using the MS-DOS FORMAT command before you run the Diskette format test. Then use that diskette when you run any of the other destructive tests. Check that you have inserted the correct diskette before you enter Y at the Proceed prompt.
You may see the following message if you attempt to run the Change line test on a drive that does not support a change line, such as a 360KB or 720KB drive: Change line not available The controller di.
Before running the test, be sure that the printer is on-line, paper is loaded, and all connections are secure, or you may see one of the following error messages: Error - Printer out of paper Error - .
If you see one of the following errors, there may be a problem with the controller or the test cable: Error - Break detected Error - Framing error Error - Overrun error Error - Parity error Error - Time out! Check to make sure that the test connector is securely connected to the port.
C-26 Performing System Diagnostics.
Appendix D Troubleshooting You should not encounter any difficulties as you set up and use your computer, but if anything out of the ordinary happens, refer to this appendix. You can correct most problems by adjusting a cable connection, repeating a software procedure, or resetting the computer.
3. When the computer performs a memory test, the version number of your system ROM BIOS appears at the bottom of the screen. Quickly write down the version number. If you do not have enough time to write down the entire number, press RESET and try again.
The Computer Won’t Start If your computer does not start when you turn on the power, check the following: 1. 2. 3. 4. Is the power light on? If not, remove any diskettes and turn off the power. Check that the power cord is securely connected to both the AC inlet on the back panel and an electrical outlet.
The Computer Does Not Respond If your computer locks up and does not respond when you type on the keyboard, follow these steps: 1. Some operations take longer than others to complete. For example, the computer takes longer to sort a database than to accept a single typed character.
7. If your computer still does not respond, you can reset it using the Ctrl Alt Del command or the RESET button. See “Resetting Your Computer” in Chapter 3 for more information. 8. If resetting the computer does not work, turn it off and wait at least five seconds.
Accessing Your Current Pass word If you have forgotten your current password and cannot use your computer, follow these steps: 1. Turn off the computer and follow the instructions under “Changing the Jumper Settings” in Chapter 5 to disable the password function by setting jumper J2 to position A.
If you did not set a new password, you do not see the Enter Password prompt and you can access your system immediately. Note Keyboard Problems If you are having trouble with the keyboard, check the following: 1. If the screen displays a keyboard error when you turn on or reset the computer, make sure the keyboard is securely connected to its port.
Monitor Problems For monitor problems, check the following: 1. If there is no display on the screen, check that the monitor’s power switch is on and that the power light on the monitor is lit. If the power light is on but you still do not see anything on the screen, check the monitor’s brightness and contrast controls.
Note If your application program requires a monitor that supports graphics but you have a monochrome monitor, the results will be unpredictable. 8. If you installed a display adapter card in your comp.
3. If reinserting the diskette does not solve the problem and you have access to another diskette drive of the same type, place the diskette in the other drive and repeat the operation. If this works, the trouble may be in your diskette drive. See “Diskette Drive Problems,” below.
If you see one of these messages, make sure the diskette is properly inserted in the drive. On a 5 %-inch diskette drive, make sure the drive latch is closed. Try the operation again. If the problem persists, try removing the diskette and reinserting it.
3. Did you run the SETUP program to define the correct type of diskette drive as part of the computer’s configuration? (See Chapter 2 for instructions.) 4. If you are still having trouble with the drive, run the Floppy disk system diagnostic tests, described in Appendix C.
Installing the Drive If you are having problems with a newly-installed drive, check the following: 1. If your dealer installed the drive, consult that person about the problem.
Preparing the Drive Before you can store data on a new hard disk (which has already been physically formatted), you must do the following to prepare it for use: 1. Run the SETUP program to define your hard disk as part of the computer’s configuration.
If you still have trouble with your hard disk, you can back up your data and physically reformat the disk. Then you’ll need to reinstall MS-DOS and copy your files back onto the disk. See “Hard Disk Format” in Appendix C and your MS-DOS Reference Manual for instructions.
4. An application program can occasionally lock the computer, making it unresponsive to the keyboard. If your computer does not respond when you type on the keyboard, you can reset it. Follow the instructions in Chapter 3. 5. If resetting the computer does not help, turn off your system, wait five seconds, and then turn it back on.
5. 6. 7. If it does not, you may need to change the internal setting of the computer’s parallel port for a parallel printer (or serial port for a serial printer). To do this, use the MS-DOS MODE or SETMODE command. See your printer manual and the MS-DOS Reference Manual for more details.
3. Did you set the necessary jumpers on the main system board? See Chapter 5 for more information. 4. Did you run the SETUP program to update your configuration after installing the card? See Chapter 2.
Memory Module Problems If you added extra memory to your system by installing SIMMs and that memory is not operating properly, check the following: 1, If the memory count displayed by the power-on diagnostics program is incorrect, you or your dealer may not have installed the SIMMs correctly.
Math Coprocessor Problems If your math coprocessor does not seem to be operating properly, check the following: 1. Run the SETUP program and check to make sure that the math coprocessor is listed as Installed on the SETUP display. If it is listed as Not installed, you or your dealer may have installed the coprocessor incorrectly.
Glossary Address A number or name that identifies the location where information is stored in a computer’s memory. Analog monitor A monitor that generates, responds to, or acts upon analog data. Analog data is transmitted by varying the voltage levels in a continuous current.
Automatic speed The feature that enables the computer to switch automatically from high speed (16 MHz) to low speed (8 MHz) when accessing a diskette drive. Backup An extra copy of a program, data file, or disk, that is created in the event your working copy is damaged or lost.
A sequence or group of eight bits that represents one character. CGA Color Graphics Adapter. A type of display adapter card that can generate up to 25 lines of text with 80 characters on each line, monochrome graphics at 640 x 200 resolution, or four- color graphics at 320 x 200 resolution.
Configuration The particular setup of a group of components. A typical system configuration consists of a computer with one diskette drive and one hard disk drive connected to a monitor and a printer.
Cylinders The vertical alignment of tracks in a hard disk that can be lined up under one read/write head. The number of tracks on a disk is equal to the number of cylinders times the number of heads. Data Information such as text or graphics stored or processed by a computer.
Diagnostics The tests and procedures the computer performs to check its internal circuitry and set up its configuration. DIP switch Dual Inline Package switch.
DOS Disk Operating System. A commonly used operating system that controls the computer’s input and output functions. See also Operating system. Double-density A type of diskette format that allows you to store twice as much data as the standard-density format.
file A group of related pieces of information called records, or entries, stored together on a disk. Text files consist of words and sentences. Program files consist of codes and are used by computers to interpret and carry out instructions. Filename A name up to eight characters long that MS-DOS uses to identify a file.
High-density A type of format that allows you to store more data than on single- or double-density diskettes. A 5’/-inch high-density diskette can store 1.2MB of data. A 3?4.-inch high-density diskette can store 1.44MB of data. Input/output (l/O) port See Port.
Math coprocessor An optional device that enables the computer to process certain mathematical calculations faster. MCGA Monochrome/Color Graphics Adapter. A type of display adapter that runs either a monochrome or color graphics monitor. MDA Monochrome Display Adapter.
Memory on card The additional memory on an option card installed in the computer. MGA Multi-mode Graphics Adapter. A type of display adapter card that can display monochrome text and color graphics on the screen. Microprocessor A small version of a CPU contained on one semiconductor chip.
MS- DOS Microsoft Disk Operating System. The operating system most commonly used with your computer. See also Operating system. Numeric keypad The number and cursor control keys grouped to the right of the keyboard. Operating speed The speed at which the central processing unit can execute commands.
Parity A method used to verify the accuracy of data transmissions by adding a bit that makes the total of the byte odd for odd parity or even for even parity. Partition (1) The area defined on a hard disk for use by an operating system; (2) to divide a hard disk into separate sections or logical drives.
Processor speed See Operating speed. Program A file that contains coded instructions and tells a computer what to do and how to do it. Prompt A message the screen displays to request information or tell you what action you need to perform next. See also Command prompt.
Reset To reload a computer’s operating system so you can retry a task or begin using a different operating system. Resetting erases all information in RAM. RCB Red Green Blue. A type of color monitor. ROM Read Only Memory. A portion of memory that can only be read and cannot be used for temporary storage.
Shadow RAM The feature provided by the Equity 386SX/16 PLUS that enables the computer to copy the system ROM BIOS and video ROM into the RAM area of memory to speed up processing. SIMM See Memory module. Software The programs that enable your computer to perform the tasks and functions you indicate.
Tracks Addressable, concentric circles on a disk, resembling the grooves on a record, which help to divide the disk into separate accessible areas. VGA Video Graphics Array.
18 Glossary.
Index A AUTOEXEC.BAT, 4-1 -2 Auto speed, 2-11, 4-2 -3 B Backing up data, from diskettes, 3-10, 3-17 on hard disk, 3-17-18 with BACKUP, 3-17 with DISKCOPY, 3-17 BACKUP, 3-17 Base memory, 2-3, 2-10, 4-7, A-5 Batch files, 4-1 -2 AUTOEXEC.
CTRL ALT +, 4-4 CTRL ALT -, 4-4 CTRL ALT DEL, 3-5 CTRL BREAK, 3-3 CTRL C, 3-3 Cursor bar, 2-3 D Date, setting, 2-3 Diagnostics, power-on, D-2 system, C-1 -25 DISKCOPY, 3-10, 3-17 Diskette drive, cable.
F Files, AUTOEXEC.BAT, 4-1 -2 backing up, 3-17-18 batch, 4-1 -2 CONFIGSYS, 1-14, 4-7-11 copying, 3-17-18 EMM386SX.SYS, 4-7-11 ESPEED, 4-5 HDSIT, 3-19-20 Floppy disk drive, see Diskette drive Floppy di.
L LIM 4.0 EMS, 4-7 Loading MS-DOS, 3-14-15 Location, choosing for computer, 1-1 -2 Low speed, 2-11, 4-2-6 Low-level format, see Physical formatting M Map, system memory, A-5 Mass storage, A-3 Master d.
Options, installing, 5-1 -43, B-1 -54 OS/2, Intro-2, 3-1 P Packing materials, 5-15 Parallel, cable, 1-8 -10 interface, 1-8 -10, 2-15, A-2 port, 1-8 -10, 2-15 port test, C-23 -24 Partitions on hard dis.
SETUP program, EMS size, 2-12-13 error message, 2-2, 2-17 hard disk drive type(s), 2-5 -8 keyboard test function, 2-9 leaving the program, 2-16-17 math coprocessor, 2-3 memory, 2-3, 2-10, 2-12-13 para.
Video car&, MDA, 1-7, 2%-9 MGA, 1-7, 2-8-9 problems, D-5, D- 17-18 removing, 5-16-17 setting display type, 2-8-9 tests, C-11 -12 VGA, 2-8 -9 Video diagnostics, C-l 1-12 Video graphics array (VGA),.
TURBO speed hard disk light access light diskette drive power button RESET button diskette hard disk or release latch diskette drive slot power light power inlet option card slots VGA monitor port pa.
EPSON®.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Epson 386SX/16 PLUS c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Epson 386SX/16 PLUS - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Epson 386SX/16 PLUS, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Epson 386SX/16 PLUS va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Epson 386SX/16 PLUS, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Epson 386SX/16 PLUS.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Epson 386SX/16 PLUS. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Epson 386SX/16 PLUS ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
