Manuel d'utilisation / d'entretien du produit 500C du fabricant Eagle Electronics
Aller à la page of 140
Pub. 988-0156-051 www.eaglesonar.com Mapping GPS Receiver Installation and Operation Instructions.
Copyright © 2004 LEI-Eagle. All rights reserved. No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Eagle Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited.
i Table of Contents Section 1: Read Me First! ............................................................... 1 Capabilities and Specifications: IntelliMap ® 500C ........................... 2 How GPS Works ...........................................
ii Navigate a Back Trail (backtrack, or reverse) ............................. 52 Transfer Custom Maps and GPS Data Files ................................... 53 Custom Maps: .............................................................................
iii To setup Loran TD: ....................................................................... 75 Customize Page Displays ................................................................. 76 GPS Simulator ..............................................
iv Trail Visible/Invisible and Other Trail Options ........................ 101 Transparency .................................................................................. 101 To adjust Menu Transparency level: ....................................
1 Section 1: Read Me First! How this manual can get you out on the road, fast! Welcome to the exciting world of digital GPS! We know you're anxious to begin navigating, but we have a favor to ask.
2 After you've learned the basics (or if you already have some GPS ex- perience), you may want to try out some of the IntelliMap 500C's many advanced navigation features. That brings us to Section 4, Advanced GPS Operations . This section contains the rest of the unit's GPS com- mand functions, organized in alphabetical order.
3 Case size: ......................... 5.4" H x 6.9" W x 3.4" D (13.8 x 17.6 x 8.6 cm); sealed and waterproof; suitable for salt- water use. MMC slots: ...................... One with waterproof door (SD card compatible). Recording: ...
4 Zoom range: .................... 40 ranges; 0.02 to 4,000 miles. NOTE: The above memory capacities refer only to the IntelliMap 500C's on- board memory. The amount of GPS data you can record and save for recall later is limited only by the number of MMC cards you have.
5 The background map is suitable for many navigation chores, but for maximum accuracy and much more detail, you need our optional map- making software, MapCreate 6. Some unit features — such as search- ing for businesses and addresses — won't work without a custom Map- Create map.
6 Introduction to GPS and WAAS Well, now you know the basics of how the unit does its work. You might be ready to jump ahead to Section 2, Installation & Accessories, on page 11, so you can mount your IntelliMap 500C and plug in the power. Or you might want to see how our text formatting makes the manual tuto- rials easy to skim.
7 The system requires signal reception from three satellites in order to determine a position. This is called a 2D fix. It takes four satellites to determine both position and elevation (your height above sea level — also called altitude). This is called a 3D fix.
8 receiver is only a tool. Always have another method of navigation avail- able, such as a map or chart and a compass. Also remember that this unit will always show navigation information in the short.
9 4. The wait message disappears and the IntelliMap 500C begins show- ing navigation information along the trail. Now, begin moving and fol- low your IntelliMap 500C. Translated into complete English, step 1 above would mean: "Start on the Map Page.
10 Notes.
11 Section 2: Installation & Accessories Preparations You can install the GPS system in some other order if you prefer, but we recommend this installation sequence: Caution: You should read over this entire installation section before drill- ing any holes in your vehicle or vessel! 1.
12 You need to select an antenna installation location that has a clear, un- obstructed view of the sky. After the module is installed, route the cable to the unit, plug it in the center socket on the back and your system is ready to use.
13 For example, if you have to extend the power cable to the battery or power buss, attach one end of the fuse holder directly to the battery or power buss. This will protect both the unit and the power cable in the event of a short. It uses a 3-amp fuse.
14 Cable connections. NMEA Cable Connections NMEA is a standard communications format for marine electronic equipment. For example, an autopilot can connect to the NMEA inter- face on the IntelliMap 500C and receive positioning information. The IntelliMap 500C can exchange information with any device that trans- mits or receives NMEA 0183 data.
15 See the diagrams on the following page for general wiring connections. Read your other product’s owner’s manual for more wiring information. NMEA Wiring To exchange NMEA data, the IntelliMap 500C has one NMEA 0183 version 2.0 communication port.
16 Optional R-A-M mounting system. Bracket Installation Mount the IntelliMap 500C in any convenient location, provided there is clearance behind the unit when it's tilted for the best viewing angle. You should also make sure there is enough room behind the IntelliMap 500C to attach the power and GPS antenna/receiver module cables.
17 Front view (left) and side view (right) showing dimensions of the IntelliMap 500C when mounted on gimbal bracket. After drilling the hole, pass the antenna connector up through the hole from under the dash. Pass the power cable's bare-wire end down though the hole from the top.
18 In-dash mounting template for the IntelliMap 500C, showing dimensions. NOTE: The figure above is not printed to scale. a scaled template (FM-5 In-Dash Adapter Kit instructions) is available for free download from our web site, www.
19 Install batteries in power pack battery adapter. MMC or SD Card Memory Card Installation Your IntelliMap 500C uses a MultiMedia Card to store information, such as custom maps, waypoints, trails and other GPS data. The unit can also use Secure Digital Cards (SD card or SDC) to store data.
20 Memory card compartment with a 16 MB MMC card installed. To remove an MMC 1. Open the card compartment door by unscrewing the thumb screw. The screw should only be finger tight. If it was over-tightened, use a thumbnail, a coin or a screwdriver to open the door.
21 MapCreate™ 6 CD-ROM, left; MMC card reader for USB ports, right. Now that you have your IntelliMap 500C installed, move on to Section 3, Basic GPS Operations . There, we'll present a series of step-by-step tutorials to teach you the basics of GPS navigation.
22 Notes.
23 Section 3: Basic GPS Operations This section addresses the unit's most basic GPS operations. The tuto- rials presented in Sec. 3 follow a chronological order. Sec. 4, Advanced GPS Operations , will discuss other more advanced functions and utili- ties.
24 3. MENU – Press this key to show the menus and submenus, which allow you to select a command or adjust a feature. Th is a ls o ac c esses search functions for streets, intersections, addresses and highway exits. 4. ARROW KEYS – These keys are used to navigate through the menus, make menu selections and move the map cursor.
25 Main Menu. The Main Menu commands and their functions are: Screen command: changes the contrast or brightness of the display screen. Sounds command: enables or disables the sounds for key strokes and alarms and sets the alarm style. Transparency command: adjust the level of transparency for menus.
26 Pages The unit has three Page displays that represent the three major operat- ing modes. They are the Satellite Status Page, the Navigation Page and Map Page. They are accessed by pressing the PAGES key, then using → or ← to select a Page. (Clear the Pages Menu by pressing EXIT .
27 Satellite Status Page. Left view indicates unit has not locked on to any satellites and has no fix on its position. Center view shows satellites be- ing scanned. Right view shows satellite lock-on with 3D position ac- quired (latitude, longitude and altitude), and WAAS reception.
28 The Satellite Status Page has its own menu, which is used for setting various options. (Options and setup are discussed in Sec. 5). To access the Satellite Status Page Menu, from the Status Page, press MENU .
29 Speed instead. Closing Speed is also known as velocity made good. It's the speed that you're making toward the waypoint. For instructions, see the Customize Page Displays entry in Sec. 5.) Track is the heading, or the current direction you are actually travel- ing.
30 course. You need to steer left to return to the desired course. You can use the ZIN or ZOUT keys to change the cross track error range. A circular symbol depicting your destination (waypoint) appears on the screen as you approach the waypoint, as shown on the screen in the preceding figure.
31 The Zoom In and Zoom Out keys zoom the map to enlarge or reduce its coverage area and the amount of mapping detail shown. There are 40 available map zoom ranges, from 0.02 miles to 4,000 miles. Far left, Map Page opening screen. Center, zoomed to 100 miles and right, zoomed to 10 miles.
32 the 2 mile range, along with minor streets. Right, at the 0.4 mile zoom, you can see an interstate highway with an exit, major and minor streets as well as Point of Interest icons.
33 When the map is zoomed out far enough, most POIs appear as square dots. As you zoom in closer, the symbols become readable icons. In the 0.2 mile zoom example at right, the cursor has selected the Cupps Café POI, which triggers a pop-up box with the POI name.
34 Digital Data map page option. In pages that have two major windows (such as two maps) you can tog- gle back and forth between the two windows by pressing PAGES | PAGES . This allows you to change which map your cursor moves on, and which map the menu operates on.
35 the window widths. Press an arrow key parallel to the centerline to switch between horizontal and vertical layout. Press EXIT to clear the four flashing arrows. From left to right: Fig. 1. Two Maps page display with four flashing arrows on the dividing centerline.
36 Basic GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, try navigating to a location at least a few blocks away. While you're learning, navigation in too small an area will constantly trigger arrival alarms.
37 Find Your Current Position Finding your current position is as simple as turning the unit on. Un- der clear sky conditions, the unit automatically searches for satellites and calculates its position in approximately one minute or less. NOTE: "Clear sky" means open sky, unobstructed by terrain, dense foliage or structures.
38 The selected wreck (the Empress) to the southeast is 12.81 miles away. Selecting Any Map Item with the Cursor 1. Use the zoom keys and the arrow keys to move around the map and find the item you wish to select. 2. Use the arrow keys and center the cursor cross-hair on the desired ob- ject.
39 After the unit has acquired a position: 1. Press WPT | ↓ to POI-R ESTAURANTS . 2. You could search the entire restaurant category, but in this example we will narrow our search.
40 POI information screen on fast food restaurant nearest this position. Screen shows name, street address, phone number, latitude/longitude, distance to restaurant and its compass bearing. Figure at left shows Go To waypoint command; right figure shows Find On Map command.
41 NOTE: Search works from mapping and POI data loaded in the unit. If you do not have a high-detailed custom map (containing POI data) for the area you are searching loaded on the MMC, you may not find anything. Set a Waypoint A waypoint is simply an electronic "address," based on the latitude and longitude of a position on the earth.
42 Sequence for setting a waypoint. Step 1: while traveling, quickly press WPT twice to call up Find Waypoint screen (seen in Step 2) and set a point. Step 3: message says the waypoint has been saved. Step 4: vehi- cle continues on its way; number waypoint symbol is visible on map.
43 3. Press ↓ to L ATITUDE | ENT . Enter the latitude by pressing ↑ or ↓ to change the first character, then press → to the next character and re- peat until the latitude is correct.
44 Navigation Page, navigating toward waypoint 001 and leaving a trail. Set Man Overboard (MOB) Waypoint One of boating's most terrifying events is having a friend or family member fall overboard. This situation can be deadly on any body of wa- ter — fresh or salt.
45 Navigating to Man Overboard: "Man Overboard activated" message shown at left. The Navigation Page is shown in the center and Map Page is shown at right. The victim is astern of the vessel; the GPS shows which direction to steer to for the rescue.
46 Navigate to cursor. In this example, the cursor has selected the town of Oologah, Oklahoma. 3. Press MENU | ENT and the unit will begin navigating to the cursor lo- cation. The Map Page will display a red line from your current position to the cur- sor position.
47 Navigate to a Point of Interest For POIs that are in view on the map, you can easily use the Navigate to Cursor command above; just use the cursor to select the POI. The other method involves searching for POIs with the Find Waypoint command, launched with the WPT key.
48 Sequence for saving a trail and beginning a new one. At left, My Trails command. Center, the Trails Menu. The arrow to the right of Trail 3 indicates the trail is "active," and the check to the left indicates the trail is visible on the map display.
49 You can save and recall up to 10 different plot trails, which can also be copied to your MMC for archiving or for transfer to your MapCreate software. Tip: Another quick way to stop recording one trail and begin a new one is to use the New Trail command: Press MENU | MENU | ↓ to M Y T RAILS | ENT | ENT .
50 The other two methods provide a full range of navigation data and work with both the Map Page and Navigation Page. The only difference be- tween them is "navigating a trail" follows a trail forward (from start to end) while "backtracking" follows a trail in reverse (from end to start.
51 Navigate a trail menu sequence: Fig. 1, My Trails command. Fig. 2, Trails Menu. Fig. 3, Edit Trail Menu. Fig. 4, Edit Route Menu with Navigate Route command highlighted for Trail 1. A trail is always con- verted to a "route" when you navigate the trail.
52 Navigate trail, map views: at left driver is heading southeast straight toward trail point 3. At right, driver has reached point 3 and has turned southwest to follow the trail.
53 4. Press → to R EVERSE R OUTE | ENT | ← to N AVIGATE R OUTE | ENT . The unit begins showing navigation information along the trail, in reverse. NOTE: If you are already located at or near the end of your trail, the arri- val alarm will go off as soon as you hit Enter.
54 The Transfer My Data submenu asks if you want to save data to the MMC or load data from the MMC into the unit's memory. 2. The Transfer My Data menu includes a message which tells you if an MMC is present or not. If no MMC is present, you must first insert a card into the unit in order to activate the Load or Save commands.
55 4. Loading to unit memory : There may be more than one GPS Data File (*.USR) on the card. To select a file, press ENT to activate the selec- tion box, use ↓ or ↑ to highlight the file, then press ENT to accept the selection. Next, press ↓ to L OAD D ATA | ENT .
56 Notes.
57 Section 4: Advanced GPS Operations Find Distance From Current Position To Another Location 1. While on the Map Page press: MENU | ↓ to F IND D ISTANCE | ENT . 2. Center your cursor over the position you want to find the distance to. A rubber band line appears, connecting your current position to the cursor's location.
58 Icons Icons are graphic symbols used to mark some location, personal point of interest or event. They can be placed on the map screen, saved and re- called later for navigation purposes. These are sometimes referred to as event marker icons. This unit has 42 different symbols you can pick from when creating an icon.
59 Delete an Icon You can delete all the icons at one time, you can delete all icons repre- sented by a particular symbol, or you can use the cursor to delete a se- lected icon from the map. 1. Press MENU | ↓ to D ELETE M Y I CONS | ENT . 2. Press ↓ to D ELETE A LL I CONS , D ELETE B Y S YMBOL , or D ELETE F ROM M AP and press ENT .
60 The course from one waypoint to the next is a leg; routes are composed of one or more legs. The legs of all GPS routes are based on straight lines between waypoints. A route provides the automatic capability to navigate through several waypoints without having to reprogram the unit after arriving at each waypoint.
61 Route Planning command on Main Menu, left, will open the Route List screen, right. 2. If necessary, press ↑ to select N EW R OUTE , then press ENT . (To add to an existing route, press ↓ or ↑ to route name | ENT .) 3. Press ↓ to (R OUTE END ) | ENT | ↓ to A DD F ROM M AP | ENT .
62 Route creation sequence, from left: Fig. 1. Set route waypoint (1) at the cove entrance. Fig. 2. Move cursor northeast to set point (2) at channel entrance.
63 8. To save your route, press EXIT . The unit reverts to the Edit Route screen, with the route automatically named "Route 1" and stored in the unit's internal memory.
64 Edit Route Waypoints menu. 3. Use ↓ and ↑ to select a command from the Edit Route Waypoints menu and press ENT . Add From Map lets you insert a waypoint in the route by clicking on a map location with the cursor. Add Waypoint calls up the Waypoint List so you can insert a waypoint from the list.
65 Route Planning command on Main Menu, left; Routes menu, center; Edit Route menu, right. Navigate Route command is selected. 2. Press ↓ to select route name | ENT | ENT . 3. Upon arrival at your destination, cancel navigation: press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT | ← to Y ES | ENT .
66 Navigating along a route: Fig. 1 shows the Navigation Page at the start of a route, heading straight for the first waypoint (Wpt 1). In Fig. 2, the traveler has arrived at Wpt 1; the arrival alarm has been trig- gered and the bearing arrow on the compass rose has turned to point toward Wpt 2, off to the northeast.
67 Tip: You can also delete all trails at once: 1. Press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press → to D ELETE A LL | ENT | ← to Y ES | ENT . Edit a Trail Name To edit a trail name: press MENU | MENU | ↓ to M Y T RAILS | ENT | ↓ to trail name | ENT | ENT .
68 At left, Edit Trail Menu with Pattern option selected. At right, edited trail with dotted line pattern. Utilities Utilities are useful tools for traveling or for outdoor activities. Alarm Clock To get to the alarm clock menu: press MENU | MENU | ↓ to T IMERS | ENT | ↓ to A LARM C LOCK | ENT .
69 2. Press WPT | → to D ELETE W AYPOINT | ENT | ← to Y ES | ENT . To return to the previous page and clear the cursor, press EXIT . To delete all waypoints at one time: press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to D ELETE A LL M Y W AYPOINTS | ENT | ← to Y ES | ENT .
70 Set a Waypoint by Average Position This feature sets a waypoint at the current position after taking several position readings and averaging them. This boosts waypoint position accuracy by helping to eliminate errors caused by atmospheric condi- tions and other factors.
71 Section 5: System & GPS Setup Options Alarms This unit has several GPS alarms. The factory default setting has all of these but the anchor alarm turned on.
72 3. To change distance settings, scroll ↓ or ↑ to select the desired cate- gory, then press → | ENT to activate the distance dialog box. Press ↑ or ↓ to change the first character, then press → to the next character and repeat until the name is correct.
73 Menus for changing Com Port settings. For connectors and wiring information for another device, see page 15. For assistance in configuring the unit to communicate with another device, consult the factory; customer service phone numbers are in the back of this manual.
74 • GSA and GSV transmits fix mode, DOP values, and satellites in view information. • DBT transmits the depth below the transducer. • DPT transmits the depth • MTW transmits the water temperature. • VLW transmits the distance traveled through water as meas- ured by the paddle wheel.
75 UTM's are marked on USGS topographic charts. This system divides the Earth into 60 zones, each 6 degrees wide in longitude. British, Irish, Finnish, German, New Zealand, Swedish, Swiss, Taiwan, and Greek grid systems are the national coordinate system used only in their respective countries.
76 Customize Page Displays Every Page display option except Full Map (on the Map Page) has cus- tomizable data boxes to provide constant on-screen information. The various data available from your unit are divided into categories in the Data Viewer menu.
77 GPS Simulator The GPS simulator lets you use the unit as if you were outdoors navigat- ing somewhere. It's a great way to practice using your unit. You can set the starting location by entering latitude/longitude (Starting Position) or from a stored waypoint, map place or POI location ( C HOOSE S TART com- mand).
78 Simulating Trail or Route Navigation In Simulator mode, your unit can automatically follow a trail or route without manual steering if you use these steps: 1. From the Map Page, go to the simulator menu. Pick a S TARTING P OSITION at or near the beginning of your trail/route.
79 Map Auto Zoom This receiver has an auto zoom feature that eliminates much of the but- ton pushing that other brands of GPS receivers force you to make. It works in conjunction with the navigation features. First, start navigation to a waypoint. (See the waypoint section for more information on navigating to a waypoint.
80 Pop-up Map Information From the Map Page, press MENU | ↓ to M AP D ATA | ENT . Press ↓ to P OPUP M AP I NFORMATION . With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT | EXIT to return to the page display.
81 ated using different datums will show the same latitude/longitude in slightly different locations. All datums are named. The GPS system is based on the WGS-84 da- tum, which covers the entire world. Other datums may also cover the entire world, or just a small portion of it.
82 Map Categories Drawn Menu. Map Fix Map Fix is used with charts or maps. This system asks for a reference position in latitude/longitude, which you take from a marked location on the map. It then shows the present position as distance on the map from that reference point.
83 Configure a map fix so the unit can find your position on a printed chart or topographical map. Press → to S ELECT O RIGIN | ENT | ENT | ENT to bring up the waypoint list. Select the waypoint (or a landmark of POI) that you saved the reference point under and press ENT .
84 This is fine if you're always traveling due north. What you see to your left corresponds to the left side of the map, to your right is shown on the right side of the map, and so on. However, if you travel any other direction, the map doesn't line up with your view of the world.
85 These figures show menu sequence (from left to right) for selecting a Navionics chart for the South Chesapeake Bay area. 3. To turn off a Navionics chart, From the Map Page, press MENU | ↓ to M AP D ATA | ENT | ↓ to N AVIONICS M AP C HOICE | ENT .
86 3. To scroll through the Service Categories window: press ENT then use ↑ or ↓ to see the types of services available. As you highlight a different category, the list in the lower window changes. To return to the Map Page, press EXIT | EXIT . 4.
87 Navionics chart showing Tidal Current Station icon selected by cur- sor. In this example, the current is flowing to the west at 0.2 kn. 2. Press WPT to display the Tidal Current Information screen. Current Information screen. The Tidal Current Information screen displays daily tidal current data for this station on this date at the present time.
88 2. Use ↑ and ↓ to select the desired month, day or year, then press ENT . To clear the information screen, press EXIT . Tide Information Navionics charts contain Tidal Information, represented at large zoom ranges by a box icon with the letter " T .
89 Tide Information screen. The Tide Information screen displays daily tidal data for this station on this date at the present time. The graph at the top of the screen is an approximate view of the tidal range pattern for the day, from midnight (MN), to noon (NN) to midnight (MN).
90 Overlay Data, with "Navigation," "Trip Calculator" and "Time" categories expanded. To overlay information on your screen: 1. While on the Navigation Page or a Map Page, press MENU | ↓ to O VERLAY D ATA | ENT . 2. You'll see a list of the overlay data currently shown, if any.
91 From Overlay Data Shown (left) press ENT to see Data Viewer (center). Select a category and press ENT ; then select information to float on screen and press ENT (right). To remove overlaid data: 1. While on the Page that shows the item or items you want to remove, press MENU | ↓ to O VERLAY D ATA | ENT .
92 1. From one of the Map Pages, press MENU | ↓ to O VERLAY D ATA | ENT . 2. You'll see a list of the overlay data currently displayed. Select the item you want to move and press ENT | → to M OVE | ENT . 3. The data begins to flash on your screen.
93 Position Pinning When you are standing still or moving at extremely slow speed, a GPS receiver can have trouble determining the direction you are traveling. In the past, this resulted in a "wandering" plot trail that moved around the map, even if you were standing still.
94 Require WAAS You can force the unit to require WAAS for reporting a valid position. (The default setting, off, uses WAAS automatically, but doesn't require it to yie ld a p osi tio n.) Here's how to turn it on and off: 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT | ↓ to R EQUIRE WAAS | ENT .
95 Screen Command, left, and Screen Menu with Contrast bar selected, right. To adjust the display's brightness: Press ↓ to B RIGHTNESS . Press → or ← to move the bar. The left end of the scale is minimum contrast; the right end is maximum contrast.
96 3. Use ↓ or ↑ to select a different language and press ENT . All menus now appear in the language you selected. Set Local Time Using the correct local time setting is handy when estimating local ar- rival time while navigating. Also, the time and date are saved when a waypoint is created.
97 3. You can return to this command and press ENT again to turn the fea- ture on. Software Version Information From time to time, Eagle updates the operating system software in some of its products. These software upgrades are usually offered to customers as free downloads from our web site, www.
98 Sounds command, left. At right, the Sounds menu. Once in the Sounds menu: To set Key Press Sounds: With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT | EXIT to return to the page display.
99 Trail Options There are several options you can use with trails. Some affect all trails, other options can be applied to a particular trail. You can change the way trails are updated, display or hide trails, create a new trail, delete a trail, etc.
100 From the Trails Menu, press ↓ to O PTIONS | ENT | ↓ to U PDATE C RITERIA . Press ← or → to select criteria type | ENT . Trail Update Rate (Time, Distance) You can update a trail by time, with a range from 1 second to 9999 sec- onds; the default is 3 seconds.
101 Edit Trail menu. New Trail To manually start a new trail, in the Trails Menu, make sure N EW T RAIL is highlighted and press ENT . Trail Visible/Invisible and Other Trail Options The name, maximum number of points in the trail, activity, and visibil- ity are all changed on the Edit Trail menu screen.
102 Main Menu with Transparency command selected. To adjust Menu Transparency level: Press MENU | MENU | ↓ to T RANSPARENCY | ENT . The T RANSPARENCY slider bar appears. Press ↑ or ↓ to move the bar. The lower end of the scale makes the menus opaque; the upper end is maximum transparency.
103 Section 6: Searching NOTE: The background map loaded in your unit lets you to search for U.S. Interstate Highway exits and exit services, as well as some land features, including cities and lakes.
104 In search results, the distance and bearing to the selected item will be calculated from the current position. In the case of a cursor search, the search results show distance and bearing from the cur- sor, but an individual waypoint's information screen shows distance and bearing from the current (or last known) position.
105 Find Address menu, left; Find Street menu, center, with Find By Name field active; street name entry complete, right. 5. To enter a city name , press ↓ to C ITY | ENT . You will be asked if you want to find addresses only within a particular city.
106 6. When the necessary search fields are filled in, press ↓ to F IND A D- DRESS | ENT . Your unit asks you to wait while it searches for the address. (If an address is not in the database, a message appears saying the ad- dress could not be found.
107 Left, Map Page showing location of the address on the map, high- lighted by cursor. Center, this address is a business in the POI data- base, so you can display the POI information window, then navigate to it. At right, this address is not in the POI database, so the Waypoint key will not display any information for this address.
108 Find Highway Exits command, left, and Find Exit menu, right. 2. First, select a highway name by pressing ENT , which calls up the Find By Name menu. There are two highway search options: A. You can spell out the highway name in the top selection box.
109 Find Exit menu, with an exit selected in the Exit List. 4. In the Exit Information screen you have two choices. A. Press ENT to navigate or "go to" the exit. B. Press → | ENT to find the exit on the map. "Go To Exit" option, left, "Find On Map" option, right.
110 Exit Information screen, left; general location and amenities information, at right. Find Map Places or Points of Interest (POI) 1. Press WPT , press ↓ or ↑ to select a map place or POI category, then press ENT . (To narrow your search, press → or ← to select a subcate- gory before pressing ENT .
111 Find by Nearest option, left, Calculating screen, center, POI list, right. 3. Search by name of POI. Press ↓ to N AME | ENT . There are two op- tions: A.
112 "Go To" POI option, left, "Find on Map" POI option, right. Find Streets or Intersections Find a Street 1. From the Map Page, press MENU | ↓ to F IND S TREETS | ENT and the Find Streets Menu appears. Find Streets command, left, Find Streets menu, right.
113 Find Street By Name menu. Spell out name in the top box, or select from the list in the lower box. 3. The Find Streets menu reappears with the street you're searching for in the First Street box. (In this example, it's I-35.) To search for that street, press ↓ to F IND F IRST S TREET | ENT .
114 Map Page showing results of a street search. The cursor points to the located street. If you want to navigate to the found street at the cursor location, just press MENU | ENT | EXIT . Find an Intersection You must enter one street in the First Street dialog box and enter the next street in the Second Street dialog box.
115 5. The Find Streets menu reappears with the first and second street dialog boxes filled in. In this example, we selected I-44 as our second street. You could now use similar techniques to select a city or Zip code, but your search will probably be faster if you leave those boxes blank.
116 If you want to navigate to the found intersection, just press MENU | ENT | EXIT . Find Waypoints 1. Press WPT | ↑ to M Y W AYPOINTS | ENT . 2. If searching for the Nearest waypoint, press ENT . If searching for the waypoint By Name , press to ↓ N AME | ENT .
117 wanted to, you could select another waypoint from the list with the ↑ or ↓ keys.) A. To navigate to the waypoint, press ENT . (The Go To Waypoint command is already highlighted.) The unit will show navigation infor- mation to the waypoint. B. To find the waypoint, press → to F IND O N M AP | ENT .
118 Find By Name menu, left. Waypoint Information screen, center. At right, the found waypoint is highlighted by cursor on Map Page. A. To navigate to the waypoint, press ENT . (Go To Waypoint command is already highlighted.) The unit will show navigation information to the waypoint.
119 Section 7: Supplemental Material Datums Used by This Unit WGS 1984 Default Adindan Mean for Ethiopia, Sudan Adindan Burkina Faso Adindan Cameroon Adindan Ethiopia Adindan Mali Adindan Senegal Adin.
120 Chua Astro Paraguay Corrego Alegre Brazil Dabola Guinea Djakarta (Batavia) Indonesia (Sumatra) DOS 1968 New Georgia Islands (Gizo Island) Easter Island 1967 Easter Island European 1950 Mean for Au.
121 Naparima BWI Trinidad & Tobago North American 1927 Mean for Antigua, Barbados, Barbuda, Caicos Islands, Cuba, Dominican Republic, Grand Cayman, Jamaica, Turks Islands North American 1927 Mean .
122 Point 58 Sweden Santo (DOS) 1965 Espirito Santo Island Sao Braz Azores (Sao Miguel, Santa Maria Islands) Sapper Hill 1943 East Falkland Island Schwarzeck Nambia Selvagem Grande Salvage Islands SGS.
123 FCC Compliance This device complies with Part 15 of the U.S. Federal Communi- cations Commission (FCC) Rules. Operation is subject to the fol- lowing two conditions: (1) this device may not cause harmful in- terference, and (2) this device must accept any interference re- ceived, including interference that may cause undesired opera- tion.
124 Notes.
125 Index A Accessories 1, 3, 4, 6, 12, 17, 18, 23, 24, 35, 58, 115 Alarm Clock ......................... 74 Alarms27, 39, 40, 55, 56, 58, 72, 78, 79, 86 Anchor Alarm ................ 78, 79 Antenna ..1, 3, 5, 12, 13, 18, 20, 21, 39, 41, 138 Arrival Alarm39, 40, 55, 56, 58, 72, 78, 79, 86 B Backlights / Lighting .
126 .............................. 82, 91, 92 Map Orientation ...... 33, 92, 93 Map Overlays (Map Data option)......................... 87, 89 Memory Cards (MMC)1, 3, 4, 5, 6, 22, 23, 24, 25, 28, 34, .
127 32, 33, 40, 48, 51, 52, 53, 54, 55, 56, 57, 58, 73, 74, 86, 90, 103, 109, 110, 111, 112; Delete ............... 73; Delete All ...................... 110; Edit Name ........................... 73; Navigate ..........................55; New Trail .
128 Notes.
129 EAGLE DATABASES LICENSE AGREEMENT THIS IS a LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST PURCHASES THIS PRODUCT AS a CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD USE ("YOU") AND EAGLE ELECTRONICS, a DI- VISION OF LEI, THE MANUFACTURER OF THIS PRODUCT ("WE", "OUR", OR "US").
130 DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Eagle Electronics, a division of LEI, the manufac- turer of this product. "You" or "your" refers to the first person who purchases the product as a consumer item for personal, family, or household use.
131 EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to EAGLE ELECTRONICS, a division of LEI, the manufac- turer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family, or household use.
132 How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert service and genuine Eagle replacement parts. If you're in the United States and you have technical, return or repair questions, please contact the Factory Customer Service Department.
Accessory Ordering Information for all countries To order Eagle accessories such as computer cables or MMC cards, please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be able to assist you with these items.
Visit our web site: www.eaglesonar.com Eagle Pub. 988-0156-051 Copyright © 2004 All Rights Reserved Printed in USA 121004 LEI-Eagle .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Eagle Electronics 500C c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Eagle Electronics 500C - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Eagle Electronics 500C, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Eagle Electronics 500C va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Eagle Electronics 500C, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Eagle Electronics 500C.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Eagle Electronics 500C. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Eagle Electronics 500C ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
