Manuel d'utilisation / d'entretien du produit Viper (2006) du fabricant Dodge
Aller à la page of 264
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
I n f o r m a t i o n P r o v i d e d b y :.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 6 䡵 V ehicle Identification Number ............... 6 䡵 V ehicle Modifications / Alterations .
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
INTRODUCTION 5 1 I n f o r m a t i o n P r o v i d e d b y :.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedur es which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information.
VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
I n f o r m a t i o n P r o v i d e d b y :.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 2 ▫ Ignition Key .......................... 1 2 ▫ Key-In-Ignition Reminder ................ 1 3 ▫ Power Accessory Delay Feature ............
▫ T o Arm The V ehicle Theft Alarm System ...... 2 1 ▫ Entering The T runk/Liftgate W ith The System Armed .............................. 2 3 ▫ Security System Disarm .................. 2 3 ▫ T amper Alert ......................... 2 4 䡵 T runk Safety W arning — Convertible Models Only .
▫ Safety Checks Y ou Should Make Inside The V ehicle .............................. 5 3 ▫ Safety Checks Y ou Should Make Outside The V ehicle .....
A WORD ABOUT YOUR KEYS The dealer that sold you your new V iper has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys fr om your dealer or a locksmith. Ask your dealer for these numbers and keep them in a safe place.
Press clutch and insert the ignition key fully , then turn the switch to one of the four illustrated positions. It may be difficult to turn the key from the OFF/LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily .
Power Accessory Delay Feature The Power Accessory Delay feature provides the cus- tomer with the ability to operate the power windows, and the radio for 2 minutes after the ignition switch is turned off.
Mechanical Release The driver’s door can be opened mechanically by insert- ing your key into the lock located on the underside of the door panel, beneath the outside mirror .
Automatic Door Locks The doors will lock automatically from outside the ve- hicle when vehicle speed reaches 18 miles per hour with the ignition On and the DOOR UNLOCKED displayed in the odometer will disappear . NOTE: If the vehicle is moving faster than 5 MPH, the inside and outside door handles are ignored.
T o Unlock the Doors: Press and r elease the UNLOCK button on the transmitter . The front and r ear park/turn signal lights will blink once to indicate that only the driver’s door is unlocked.
T o Lock the Doors: NOTE: T o enable/disable the Lamp Flash, see proce- dure described above. Press and release the LOCK button on the transmitter . The horn will chirp once and the park and tail lights will blink to acknowledge that the door is locked and that the alarm system is armed.
T o Program T ransmitters: This feature allows you to program transmitters in case one is lost or an extra transmitter(s) is desired. Up to 4 transmitters can be programmed to your vehicle. T o program another transmitter follow these steps: 1. T urn the ignition switch to the ON/RUN position and set the parking brake.
T ransmitter Battery Service The replacement battery number is 2016. This is a generic battery , readily available at local retail stores. 1. Pry the transmitter halves apart with a coin or similar object. 2. Remove and replace the batteries. 3. Reassemble the transmitter case and test operation.
VEHICLE THEFT ALARM The system monitors the doors, tr unk/liftgate, hood, and ignition for unauthorized operation. Once the system has been armed, opening any door , trunk/liftgate (with the ignition key), hood or turning the ignition key to any position will trigger an alarm.
3. After the last door is closed, the security light will flash for 15 seconds. If there is a fault in the system or if the hood or trunk/liftgate is not closed, the V ehicle Theft Alarm lamp will remain ON steady for 15 seconds until the system is armed.
CAUTION! If the Security lamp flashes twice every 6 seconds, then the vehicle was tampered with! Entering the T runk/liftgate with the System Armed T o enter the trunk/liftgate with the system armed, you must first press the Remote Keyless Entry T runk/liftgate button.
2. Or , press the UNLOCK button on the Remote Keyless Entry transmitter . The fr ont and r ear park and turn signal lights will flash to acknowledge the signal. (See the Remote Keyless Entry Section of this manual for opera- tion) NOTE: The vehicle will not start unless the V ehicle Theft Alarm System is disarmed by either of the two methods above.
TRUNK SAFETY W ARNING — CONVERTIBLE MODELS ONL Y W ARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended.
pulling on the lever attached to the trunk latching mechanism, which is coated so that it glows in a dark- ened trunk. LIFTGA TE — COUPE MODELS ONL Y The liftgate can be unlatched by using the vehicle key or with the remote keyless entry transmitter .
WINDOWS Power Windows The power window switches are located between the driver and passenger seats on the center tunnel bezel, just to the left of the parking brake. The switch on the left side controls the driver’s window and the switch on the right controls the passenger’s window .
Auto Down Feature Both windows have an auto down feature. Press the window switch to the second detent, release, and the window will go down automatically .
NOTE: The W indow Up switch will not function with the door open and while the system is in the Power Accessory Delay mode. If the window is in the process of going up, opening the door will stop the window move- ment immediately .
Research has shown that seat belts save lives. They also can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts provide protection against that, and they r educe the risk of injury caused by striking the inside of the vehicle.
Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is located at the side of your seat back. Grasp the latch plate and pull out the belt. 3. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.
W ARNING! A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury . W ear your seat belt snugly . A belt that is worn under your arm is very danger- ous. Y our body could fall into the inside surfaces of the vehicle in a collision, increasing head and neck injury .
W ARNING! A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. 7. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck.
The Enhanced W arning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or ST ART position.
Six Point Belt System - If equipped This six point belt system meets SCCA standards and should be only used when engaged in related perfor- mance driving events. The standard lap/shoulder belt should be used whenever the vehicle is operated on the street.
W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system.
child seat owner’s manual to ensure you have the right seat for your child. Use the r estraint system that is correct for your child. T wo different child restraint systems are generally avail- able: • The infant carrier for babies weighing up to approxi- mately 20 lbs.
W ARNING! Improper installation can lead to failure of a child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manu- facturer’s directions exactly when installing a child restraint. • Child restraints are secured in the passenger seat by the lap part of the lap/shoulder belt.
system provides for the installation of the child restraint without using the vehicle seat belt. The passenger seat has an exclusive lower anchorage. These are round bars, located at the lower ar ea of the seat back, one on each side of the passenger seat.
illustration which follows. While the child tether is in use, keep the access cover in a safe place so that it can be replaced after use of the child tether . T o attach the tether strap to the anchor , move the seatback fully forward. Pass the child restraint tether hook through either opening in the seatback under the head restraint.
W ARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap.
T o convert the emergency locking mode to automatic locking mode for seat belts equipped with automatic locking retractors, grasp on the shoulder belt portion of the belt and pull all of the webbing out of the retractor .
Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for the driver and passenger as a supplement to the seat belt r estraint systems. The driver’s airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrument panel, under a cover marked SRS/AIRBAG.
The seat belts are designed to protect you in many types of collisions. The airbags deploy only in frontal collisions and will not deploy in collisions at slow speed. But even in collisions where the airbags deploy , you need the seat belts to keep you in the right position for the airbags to protect you properly .
Y ou should read the instructions provided with your child r estraint to make sur e that you are using it pr operly . 2. All occupants should wear their lap and shoulder belts properly . 3. The driver and passenger seats should be moved back as far as practical to allow the airbags room to inflate.
How The Airbag System W orks • A crash sensor in the occupant compartment deter- mines if a frontal impact is severe enough to requir e the airbag. The sensor will not detect side, roll over , or rear impacts. The crash sensor is connected to the diagnostic unit and to the airbag/inflator unit.
• When the crash sensors detect an impact requiring the airbags, they signal the inflator units. A lar ge quantity of non toxic nitrogen gas is generated to inflate the airbags. The airbag covers separate and fold out of the way as the airbags inflate to their full size.
However , if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately . • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non toxic nitrogen gas used for airbag inflation.
• is a child, age 1 to 12 who must ride in the front seat because there is no rear seat, because there is no rear seat position available, or because the child has a medical condition which makes it.
NOTE: When the passenger airbag is turned off the airbag off light will illuminate T o Shut Off the Passenger Airbag: • Place only the tip of the ignition key in the on/off switch, turn the key clockwise, and remove the key from the switch. This will shut off the passenger side airbag.
Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured because the airbag is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the airbag covers.
T ransporting Pets Deploying airbags could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in pet harnesses or pet carriers that are secured by seat belts.
SAFETY TIPS Exhaust Gas W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. T o avoid breathing (CO) follow the safety tips below .
Safety Checks Y ou Should Make Outside the V ehicle T ires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect for tread cuts or side wall cracks. Check wheel nuts for tightness and tires for proper pressure.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Convertible T op Operation — Convertible Models Only ................................. 5 7 ▫ T o Lower The T op ...................... 5 8 ▫ T o Raise The T op ...................... 5 8 ▫ Convertible T op Boot Cover Installation– If Equipped .
▫ Interior Lights ........................ 7 6 ▫ Multi-Function Control Lever .............. 7 6 ▫ Headlights, Parking Lights, Instrument Panel Lights, And Front Fog Lights .............. 7 8 ▫ Daytime Running Lights ................. 7 8 ▫ Lights-On Reminder .
CONVERTIBLE TOP OPERA TION — CONVERTIBLE MODELS ONL Y W ARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision.
T o Lower the T op: 1. T o lower the top, first ensure that the door windows are lowered at least an inch. 2. Depress the button at the top of the latch upwards and then pull the handle down and rearward, towards you.
3. Release the lever located behind the driver’s seat and nestled in the folded convertible top (as pictured). T o aid in disengaging the latch, press down on the convertible top while pressing on the latch lever . 4. Manually raise the top until it meets the windshield header (as pictured).
6. While sitting inside the vehicle, hold onto the handles and pull the top towards the windshield header . Push the latch handle forward and engage the latch hook to the windshield receiver rod. 7. Ensure the outboard locating pins are in their respec- tive receiving holes in the windshield header .
NOTE: Until the convertible top system has had ad- equate time to break in, it may take greater effort to engage the latch hook and close the latch. Several weeks of normal convertible top usage will reduce these efforts. Convertible T op Boot Cover Installation–If Equipped 1.
4. Slide pocket over the front corner of convertible top on the passenger side. 5. Stretch and slide pocket over the front corner of convertible top on the driver side.
6. T uck cover under leading edge of convertible top. 7. Clip tab under trunk lid stop and quarter panel flange on outer edge on the passenger side. T ucking Boot Cover Attaching Passenger Side T ab U.
8. Push down to engage inboar d tab on the passenger side. 9. Clip tab under trunk lid stop and quarter panel flange on outer edge on the driver side. Engaging Passenger Side T ab Attaching Driver Sid.
10. Push down to engage inboard tab on the driver side. Push down on convertible top behind driver seat to lock down. 1 1. Stretch out and smooth cover from rear of vehicle.
12. Ensure that the forward edge of the convertible top boot is tucked in fully after the trunk is closed. Convertible T op Boot Cover Removal and Storage 1.
3. Pull up to disengage the inboard tab on the passenger side. 4. Fold each of the outer edges of the convertible top cover inward. Disengaging Passenger Side T ab Folding Outer Edges UNDERST ANDING T.
5. Fold the convertible top cover again. Place the cover into the bag. Store the cover in the trunk or a dry secure area. CONSOLE FEA TURES The front console has a removable ashtray , power outlet/ cigarette lighter and power window switches.
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window . A pivot system allows for horizontal and verti- cal mirror adjustment. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Electric Remote Control Mirrors Both of the outside mirrors can be adjusted by using the remote controls mounted inside the driver’s door , below the door handle and power door switch. NOTE: Place the mirror selector switch in the center (neutral) position to prevent accidental movement of the mirrors.
W ARNING! V ehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in this convex mirror .
W ARNING! Adjusting a seat while the vehicle is moving is dangerous. If you are driving, the sudden movement of the seat could cause you to lose control. Y ou could be injured. Adjust any seat only while the vehicle is parked. Do not ride with the seatback reclined so that the shoulder belt is no longer riding against your chest.
Reclining Seat The recliner control is on the side of the seat on the door-side. T o recline, lean forward slightly befor e pulling the lever , then lean back to the desired position, and release the lever . Lean forward and pull the lever to return the seatback to its original position.
Then push the safety catch handle located under the front edge of the hood toward the right. Raise the front of the hood. NOTE: Assist props will raise the hood to a normal customer usage position. If greater access is required, the hood may be pushed up at the front, raising the hood beyond the initial opening height.
W ARNING! If the hood is not fully latched, it could open when the vehicle is moving and block your forward vision. Be sure the hood latches are fully latched before driving. LIGHTS Courtesy/Reading Lights These lights, located under the rearview mirror , come on whenever a door is opened or the illuminated entry system is activated.
On Coupe models there is an additional light for the liftgate. The liftgate light and courtesy lights will turn ON when the liftgate is opened. The liftgate light and courtesy lights fade to OFF in about 4 seconds after the liftgate is closed.
Dimmer Control W ith the parking lights or headlights on, rotating the dimmer contr ol for the interior lights on the Multi-Function Control Lever upward will increase the brightness of the instrument panel lights. Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights.
Headlights, Parking Lights, Instrument Panel Lights, and Front Fog Lights T urn the end of the Multi-Function Control Lever to the first detent for parking light operation. T urn to the second detent for headlight operation. Pull out the end of the Multi-Function Control Lever to turn on the front fog lights.
Headlight Time Delay This feature provides the safety of headlight illumination for about 90 seconds. T o activate the delay , turn off the ignition while the headlights are still on. Then turn off the headlights within 45 seconds. The delay interval begins when the headlamp switch is turned off.
T urn Signals Move the Multi-Function Control Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Y ou can signal a lane change by moving the lever partially up or down without moving beyond the detent.
Tilt Steering Column T o tilt the column, simply pull down the small lever below the turn signal control and move the wheel up or down, as desired. Return the lever to the up position to lock the wheel firmly in place. W ARNING! T ilting the steering column while the vehicle is moving is dangerous.
ADJUST ABLE PEDALS Y our V iper is equipped with an adjustable pedal system that allows about 4 inches (100 mm) of fore and aft pedal adjustment. The pedals are adjusted using a switch recessed into the knee bolster beneath the steering col- umn. T o adjust the pedals: • Adjust the seat to a comfortable driving position.
Adjustable Left Foot Rest The left foot rest can be manually adjusted fore and aft and rotated up and down to a comfortable position. T o adjust the left foot rest: • Loosen the nut on the pedal using a 13 mm socket. • Slide the pedal fore, aft and/or rotate up or down to find a comfortable position.
WINDSHIELD WIPERS AND W ASHERS The wipers and washers are operated by a switch in the right control lever . Move the control lever up to select the desired wiper speed. Windshield Washers T o use the washer , pull the control lever toward you and hold while spray is desired.
Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause be- tween cycles desirable. Move the lever to the first detent (DEL) position, then select the delay interval by turning the end of the stalk.
I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Features .................. 8 9 䡵 Instrument Cluster Description .............. 9 0 ▫ Speedometer .......................... 9 0 ▫ T urn Signal Indicators ................... 9 1 ▫ Hazard Indicator .
▫ CD Player Operation ................... 1 0 2 䡵 Satellite Radio — If Equipped .............. 1 0 6 ▫ System Activation ..................... 1 0 7 ▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) .................... 1 0 7 ▫ Selecting Satellite Mode In RBB, RAH And RBK Radios .
INSTRUMENT P ANEL FEA TURES UNDERST ANDING YOUR INSTRUMENT P ANEL 89 4 I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER DESCRIPTION Speedometer Shows the vehicle speed in miles-per- hour and kilometers-per-hour . Odometer/T rip Odometer The odometer shows the total distance the vehicle has been driven.
T urn Signal Indicators The arrows will flash in unison with the corresponding exterior turn signal when using the signal lever . (See page 80 for more information.) Hazard Indicator Both turn signal arrows will flash in unison with all front and rear turn signals when the hazard warning switch is used.
W ARNING! If both ABS and/or Brake W arning lamps become illuminated, please seek service immediately! Y our V iper will have diminished braking capability and control if ABS and/or service brake systems are not working properly . Have your brake system serviced immediately .
CAUTION! Prolonged driving with the light on could cause further damage to the emission control system. It could also affect fuel economy and driveability . The vehicle must be serviced before any state emissions tests can be performed. If the light is flashing, severe catalytic converter damage and power loss will soon occur .
T runk/Liftgate Ajar Light This light indicates that the trunk/liftgate is not latched. Engine Coolant T emperature Light A red LED light on the Coolant T emperature gauge will illuminate to warn of an overheated engine coolant condition.
Brake System W arning Light The dual brake system provides a reserve braking capability in the event of a failure to a portion of the hydraulic system. The warning light should be checked frequently to assure that it is operating properly . This can be done by turning the ignition switch to a point midway between ON and ST AR T .
Gauges T achometer This gauge shows engine speed in revolutions- per-minute (RPM) times 1,000. A void excessive engine speeds in any part of the red warning zone, particularly when driving downhill or in lower gears. Coolant T emperature Gauge This gauge shows the engine coolant tempera- ture.
This gauge does not indicate the amount of oil in the engine. The engine oil level must be checked under the hood. Check the level often during severe usage. Fuel Gauge This gauge shows the amount of fuel in the gas tank. The reaction time of the gauge has been slowed to avoid needle fluctuation during pe- riods of high G force cornering.
2. Press the “H” button to set hours or the “M” button to set minutes. The time setting will increase each time you press a button. RADIO GENERAL INFORMA TION Radio Broadcast Signals Y our new radio will pr ovide excellent reception under most operating conditions.
FM Reception Because FM transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear , which is the major feature of FM radio.
NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press the MODE button repeatedly to select between AM, FM, the CD changer and Sirius Satellite Radio™ (if equipped).
and release that button. If a button is not selected within 5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into push- button memory .
General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired opera- tion.
show the disc number , the track number , and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number wher e the CD is being loaded. After the radio displays “load” insert the CD into the player .
FF/TUNE/R W Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner . Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play .
Program T ype Radio Display Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft R.
Ti m e Press the TIME button to change the display from elapsed CD playing time to time of day . Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. CD Diagnostic Indicators When driving over a very rough r oad, the CD player may skip momentarily .
System Activation T o activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www .sirius.com. Please have the following informa- tion available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID).
mode when any other button is pushed, the ignition is turned OFF , or 5 minutes has passed since any button was pushed. Selecting Satellite Mode in RBB, RAH and RBK Radios Press the MODE button repeatedly until ⬙ SA ⬙ appears in the display . A CD or tape may remain in the radio while in the Satellite radio mode.
NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-539- 7474 to discuss options for channel blocking or unblock- ing.
Satellite Antenna T o ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far forward as possible.
RADIO ANTENNA The radio antenna is located in the windshield. RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy perfor- mance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna.
The Air Conditioning System allows you to balance the temperature, amount and direction of the air circulating throughout the vehicle. The controls are as follows: Fan Control Use this control to regulate the amount of air forced through the sys- tem in any mode you select.
The mode control positions are as follows: Recirculate Air is recir culated inside the vehicle. Y ou may choose between Bi-Level and Panel air outlets while in this mode. Use this mode to tempo- rarily block out any outside odors, smoke, or dust and to cool the interior rapidly upon initial start up in very hot or humid weather .
NOTE: The air conditioning compressor operates in this mode. This dehumidifies the air to help dry the wind- shield. T o improve fuel economy , leave in the Defrost mode only when necessary . A/C Pushbutton W ith the fan control in the ON position, pushing the A/C button turns on the air conditioning compressor .
Operating Tips When operating the system during the winter months, make sure the air intake, at the right side of the hood, is free of ice, slush, snow or other obstructions such as leaves. Leaves collected in the air-intake plenum may reduce air flow and plug the plenum water drains.
I n f o r m a t i o n P r o v i d e d b y :.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es ..................... 1 1 9 ▫ If Engine Fails T o Start ................. 1 2 0 ▫ After Starting ........................ 1 2 2 䡵 T ransmission Shifting .................... 1 2 2 ▫ Recommended Shift Speeds .
▫ T ire Spinning ........................ 1 4 2 ▫ T read W ear Indicators .................. 1 4 2 ▫ Life Of T ire ......................... 1 4 3 ▫ Replacement T ires ..................... 1 4 3 ▫ Alignment And Balance ................. 1 4 5 䡵 Low T ire Pressur e (Ltp) System .
ST ARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust tempera- tures which can damage your vehicle.
instrument panel and release when the engine starts. If the engine has not started within 3 seconds, slightly depress the accelerator pedal while continuing to crank. If the engine fails to start within 10 seconds, turn the key to the “OFF” position, wait 5 seconds, then repeat the normal starting procedur e.
W ARNING! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery , booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.
After Starting The idle speed will automatically decrease as the engine warms up. W ARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury .
Recommended Shift Speeds T o use your manual transmission for fuel economy it should be upshifted as listed below . Shift at the vehicle speeds listed for acceleration. Earlier upshifts during cruise conditions (relatively steady speeds) will result in increased fuel economy , and may be used as indicated.
T o maintain a safe speed and prolong brake life, down- shift to maintain a safe speed when descending a steep grade. W ARNING! Skipping more than one gear while downshifting, could cause you to lose control of your vehicle. Y ou could have an accident.
Before leaving the vehicle, make sure you fully apply the parking brake. Place the transmission in REVERSE. Fail- ure to do so may cause the vehicle to roll and cause damage or injury . As an added precaution, turn the fr ont wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
All vehicle wheels and tires must be the same size and type as the original equipment wheels and tires must be properly inflated to produce accurate signals for the computer . W ARNING! Significant over or under inflation of tires, or mixing sizes of front or rear tires or wheels on the vehicle can lead to loss of braking effectiveness.
CAUTION! The Anti-Lock Brake System is subject to possible detrimental effects of electronic interference caused by improperly installed after-market radios or tele- phones.
NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the Anti-Lock Brake System is functioning. W ARNING! T o use your brakes and accelerator more safely , follow these tips: • Do not “ride” the brakes by resting your foot on the pedal.
In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort requir ed to brake the vehicle will be much greater than that requir ed with the power system operating.
TIRE SAFETY INFORMA TION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ ....blank.... ⴖ = Passenger car tire based on European design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and Tire Pressure T ire Placard Location NOTE: The proper cold tire inflation pressur e is listed on either the face of the driver’s door or the driver’s side “B” pillar .
This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires.
3. Subtract the combined weight of the driver and pas- sengers from XXX kilograms or XXX pounds. 4. The resulting figure equals the available amount of cargo and luggage load capacity . For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb.
ST ARTING AND OPERA TING 137 5 I n f o r m a t i o n P r o v i d e d b y :.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, af fect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy— Improper inflation pressur es can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life r esulting in a need for earlier tir e replacement. Underinflation also increases tir e rolling resistance and results in higher fuel consumption.
CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”.
T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressur e is very important.
Tire Spinning When stuck in mud, sand, snow , or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h). See the paragraph on Freeing A Stuck V ehicle in Section 6 of this manual. W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure.
These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tir e should be replaced. Many states have laws requiring tire replacement at this point.
wear indicators). Refer to the T ire and Loading Informa- tion placard for the size designation of your tire. The service description and load identification will be found on the original equipment tire. Failure to use equivalent replacement tires may adversely affect the safety , han- dling, and ride of your vehicle.
CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear . • Uneven tire wear , such as feathering and one-sided wear .
Although the tires are designed with a “run flat” feature that allows the vehicle to be driven about 50 miles (80 km) at 55 m.p.h. (88 kph), immediate service should be obtained if the Low T ire indicator is activated. W ARNING! Do not exceed 55 m.
TIRE CHAINS Due to limited clearance, tire chains are not recom- mended. CAUTION! Damage to the vehicle may result if tire chains are used. SNOW TIRES There are no snow tires that are compatible with the wheels on this vehicle. Tire Storage T ire storage is addressed in the Michelin Limited T ire W arranty Booklet.
GROUND CLEARANCE The V iper is a low vehicle and ground clearance is limited. CAUTION! Damage to the front and rear fascias and side sills can occur if you disregard the low ground clearance of your V iper . Pay close attention when parking to avoid running into parking curbs.
Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the W orld W ide Fuel Charter , WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane. Gaso- lines blended with MMT of fer no performance advantage beyond gasolines of the same octane number without MMT . Gasolines blended with MMT reduce spark plug life and reduce emission system performance in some vehicles.
• An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may requir e immediate service.
• Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repair ed promptly .
VEHICLE LOADING V ehicle Loading Capacities Front Seat Occupants ....................... 2 Luggage ....................... 1 1 5 l b s . ( 5 1k g ) Rated V ehicle Capacity ............ 4 1 5 l b s . (187kg) TRAILER TOWING T railer towing with this vehicle is not recommended.
I n f o r m a t i o n P r o v i d e d b y :.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher .................. 1 5 6 䡵 If Y our Engine Overheats ................. 1 5 6 䡵 Jump-Starting Procedur es ................. 1 5 8 䡵 Driving On Slippery Surfaces .............. 1 6 2 ▫ T raction .
HAZARD W ARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Depress the flasher button and all front and rear dir ectional signals will flash. Depr ess the flasher button again to turn the flashers off.
• In city traffic— While moving, shift into the highest gear possible to reduce engine RPM. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it of f. The air conditioning system adds heat to the cooling system and turning off the A/C removes this heat.
JUMP-ST ARTING PROCEDURES W ARNING! • Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
The battery is located under the battery access panel inside the rear compartment on the left side. Remote battery terminals are located in the engine compartment for jump starting.
NOTE: Remove the floor portion of the rear compart- ment carpet to gain access to the battery . 1. W ear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact.
6. Connect the other cable, first to the negative terminal of the booster battery and then to the ground (on the ear of the Thermostat Housing) of your V iper as shown.
DRIVING ON SLIPPER Y SURF ACES W ARNING! Rapid acceleration on slippery surfaces is danger- ous. Y ou could lose control of the vehicle and possi- bly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow , wet, mud, loose sand, etc.
FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow , it can often be moved by a rocking motion. T urn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and First gear .
I n f o r m a t i o n P r o v i d e d b y :.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 8.3L Engine Compartment ................ 1 6 8 䡵 Onboard Diagnostic System (OBD II) ......... 1 6 9 䡵 Emissions Inspection And Maintenance Programs ............................ 1 7 0 䡵 Replacement Parts ...
▫ Body Lubrication ..................... 1 8 6 ▫ Front And Rear Suspension Ball Joints ...... 1 8 6 ▫ Steering Linkage ...................... 1 8 7 ▫ Body Mechanism Lubrication ............. 1 8 7 ▫ W indshield W ashers ................... 1 8 9 ▫ Exhaust System .
▫ Headlight, Parking, Front Park, T urn Signal, Front Sidemarker And Front Fog Light Removal .... 2 1 2 ▫ High Intensity Discharge Headlights (HID) . . . 214 ▫ T ail, T ail/Stop, And Marker Lamp Bulb Replacement ......................... 2 1 4 ▫ Backup And Rear T urn Signal Lamp Bulb Replacement .
8.3L ENGINE COMP ARTMENT 8.3L Engine Compartment 168 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
ONBOARD DIAGNOSTIC SYSTEM (OBD II) T o meet new government regulations and promote cleaner air , your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions and engine control systems.
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system.
ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine.
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment.
The best time to check the oil level is approximately 5 minutes after a fully warmed up engine is turned off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground also will improve the accuracy of the oil level readings.
• T railer towing • Off-r oad or desert driving • If equipped for and operating with E–85 (ethanol) fuel If none of these apply to you, then change your engine oil every 6,000 miles (10 000 km) or 6 months, whichever comes first and follow the maintenance recommenda- tions in Schedule A .
Materials Added to Engine Oil The manufacture strongly recommends against the addi- tion of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental ad- ditives.
Drive Belts — Check Condition and T ension At the mileage shown in the appropriate “Maintenance Schedule”, check the condition of the drive belt for condition and proper tension.
CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly .
T o minimize the possibility of catalytic converter dam- age: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected for prolonged period.
Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on “Maintenance Schedule A”. If, however , you drive the vehicle fr equently under dusty or severe conditions, the filter element should be inspected periodically and replaced if necessary at the intervals shown in “Maintenance Schedule B”.
NOTE: Remove the floor portion of the rear compart- ment carpet to gain access to the battery . T o service the battery: 1. Locate the battery compartment inside the rear com- partment. 2. Remove the battery cover mounting screws and r e- move the battery cover .
W ARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water .
CAUTION! It is essential when replacing the cables on the battery that you attach the positive cable to the positive post and the negative cable to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case.
2. Cycle the ignition from OFF to ACC four times with- out going into ON. Leave the switch in the OFF position after the fourth cycle. 3. Depress the driver’s side Power Door Lock switch in the UP direction. A single chime and a horn chirp indicate that the process has begun.
1. Press the driver’s door exterior handle to wake up the vehicle. 2. If the door does not open (vehicle is armed) press the remote keyless entry unlock button to unlock the vehicle. 3. Press the driver’s door exterior handle again to open the door .
Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar - bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product.
Before removing the reservoir cap, wipe the outside of the cap and reservoir so that no dirt can fall into the reservoir . All power steering pumps have a dipstick. Fluid level should be maintained at the pr oper level indicated on the dipstick. If necessary , add fluid to restor e to the proper indicated level.
Damaged seals should be replaced to prevent leakage or contamination of the grease. If there is any movement within the ball joint, the knuckle or control arm must be replaced. The ball joints are not serviceable by them- selves. Relubrication Ball joints are lubricated at the factory with a special grease.
Hood Latch When performing other underhood services, the hood latch release mechanism and safety catch should be inspected, cleaned, and lubricated. It is important to maintain proper lubrication to insure that the hood mechanisms work properly and safely .
Parts that should not be lubricated are as follows: • Generator bearings • Drive belt • Accessory drive belt idler pulley • Idler arm assembly • Front wheel bearing • Rubber bushings • S.
W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. Cooling System W ARNING! Y ou or others can be badly burned by hot coolant or steam from your radiator .
Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner .
Adding Coolant Y our vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Y ears or 100,000 miles before replacement. T o prevent reducing this extended mainte- nance period, it is important that you use the same coolant throughout the life of your vehicle.
W ARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
• Do not change the thermostat for summer or winter operation. If r eplacement is ever necessary , install ONL Y the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions.
Brake, Power Steering, and Fuel System Hoses When servicing the vehicle for scheduled maintenance, inspect surface of hoses and nylon tubing for evidence of heat and mechanical damage. Hard and brittle rubber , cracking, checking, tears, cuts, abrasion, and excessive swelling suggest deterioration of the rubber .
Brake and Clutch Fluid These fluids will tend to absorb moisture from the atmosphere over a period of time. If the fluid becomes contaminated with water , brake or clutch performance will deteriorate. The brake and clutch fluid must be changed every two years.
Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter . Hydraulic Clutch The fluid in the clutch master cylinder should be checked when performing other under hood services. T o check the fluid level, r emove the r eservoir cap.
Fluid Level Check The fluid in the transmission should be checked when- ever other underhood services are done. Check the fluid level by removing the fill plug located on the left side of the transmission. The fluid level should be at the bottom of the fill hole.
Frequency of Oil Change Drain and fill the axle at the interval specified in the Maintenance Schedules. Change the fluid immediately if contaminated with water . Wheel Bearings Y our V iper has permanently sealed wheel bearings that do not requir e periodic maintenance.
Use soap and water on dull black window trim. Polish or cleaners may leave a white residue. If desired, you may polish your vehicle immediately by using Mopar Auto- mobile Polish or equivalent. Glass Surfaces All glass surfaces should be cleaned regularly with any commercial household-type glass cleaner .
Convertible T op Care — Convertible Models Only Use a mild detergent to clean the top. A void heavy scrubbing and rinse with plenty of clean water . Allow to dry thoroughly before storage. Carpeting V acuum your carpeting regularly to prevent a soil buildup.
CAUTION! The tires on your V iper are wider than the guide tracks on most washes and the low ground clearance of your vehicle may not be compatible with some car wash equipment. Y ou could damage your vehicle. FUSES — Power Distribution Center A power distribution center is located in the engine compartment.
CAUTION! • When installing the Power Distribution Center cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Power Distribu- tion Center , and possibly result in a electrical system failure.
Cavity Fuse Circuits 5 Cartridge Fuse 30 Amp Green Ignition Switch (Run & Accessory)-(Downstream) 6 Cartridge Fuse 40 Amp Batt 7 Cartridge Fuse 30 Amp Green Batt-Relay Contact, ABS Pump Motor 8 Ca.
Cavity Fuse Circuits 14 Mini Fuse 15 Amp Blue Rear 02 Sensor to Heater Relay 15 Mini Fuse 20 Amp Y ellow Electric Heated RR. WDO (EBL) 16, 17 Mini Fuse 20 Amp Y ellow Fused Feed-Cigar Lighter 18 Mini .
Cavity Fuse Circuits 23, 24 Mini Fuse 10 Amp Red Airbag, Ignition Run 25-29 ISO RE- LA Y Batt-Relay Contact, High Blower Motor 30-34 MICRO RELA Y Batt-Relay-Starter Contact to So- lenoid 35-39 MICRO R.
Cavity Fuse Circuits 68, 69 Mini Fuse 20 Amp Y ellow Left HID Headlamp 70, 71 Mini Fuse 20 Amp Y ellow Right HID Headlamp 72-76 MICRO RELA Y Batt-Run/Acc Relay 82-86 MICRO RELA Y Heated Rear W indow (.
• If the vehicle will be subjected to fr eezing tempera- tures, remove the battery and store it in a dry , well ventilated area or place a trickle charger (1.
Check the battery every 4 to 6 weeks to ensur e that the voltage is above 12.40. V oltage will drop more rapidly in hot temperatures. If battery voltage drops below 12.40, follow the battery recharge procedur e in the Service Manual. • Check that the radiator coolant level of protection is to at least -20°F (-29°C).
REPLACEMENT BULBS Interior Light Bulbs Message Center Indicators .................. 1 0 3 Cluster ................................ 1 0 3 Gauge Pack ............................ 1 0 3 Heater Control ........................... 3 7 Interior Light ......
Exterior Light Bulbs — Coupe Models Headlight-Low/High Beam .... S e r v i c e d a t dealer only Aux. Headlight-High Beam ......... (HB3A) 9005XS Front Park/T urn ...................... 3157AK Fog Light ....................... (H10 U) 9145 Front Sidemarker .
2. T wist off sockets counter-clockwise and pull out bulbs from the socket, install the new bulbs, and reinstall the bulb and socket assembly . Replace the splash shield. NOTE: On vehicles equipped with High Intensity Dis- charge Headlights (HID), when the headlights ar e turned on there is a blue hue to the lights.
High Intensity Discharge Headlights (HID) The headlights are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlight switch of f and the key removed. Because of this, you should not attempt to service a headlight bulb yourself.
2. T wist sockets counter -clockwise to pull out bulbs. Replace tail, tail/stop, or marker lamp bulb. 3. Reinstall the appropriate bulb and socket assembly . Replace the access panel. Close the trunk. Backup and Rear T urn Signal Lamp Bulb Replacement 1.
2. Remove thr ee plastic nuts from the upper lamp assem- bly . 216 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
3. T wist sockets of the three bulbs shown counter- clockwise. Disconnect bulb and socket assemblies from the upper lamp assembly . Pull the upper lamp assembly clear in order to access backup and rear turn signal lamp bulbs. 4. Replace the backup or rear turn signal lamp bulb.
License Plate Light T wist off sockets counter-clockwise and pull out bulbs. Replace as requir ed. 218 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
Headlight Aiming The headlights on your new V iper were aimed at the factory . The factory setting was made at a no load setting. A great increase in weight will change the aiming and it may be necessary to readjust the headlights if you typically carry an excessive amount of weight in the rear compartment or otherwise suspect misalignment.
FLUIDS AND CAP ACITIES U.S. Metric Fuel (approximate) 8.3 Liter Engine (Premium 91 Octane) 18.2 gallons 68.9 liters Engine Oil-W ith Filter 8.3 Liter Engines (SAE 0W -40) 10 qts. 9.5 Liters Cooling System * 8.3 Liter Engines* (Mopar 威 Antifreeze/Coolant 5 Y ear/ 102,000 Mile Formula) or equivalent.
FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/102,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) or equivalent. Engine Oil Use API rated SL/CF full synthetic engine oil.
Chassis Component Fluid, Lubricant, or Genuine Part T ransmission Mopar Synthetic Manual T ransmission Lubricant SAE 75W -85 (Castrol Syn- torq L T 75W/85) Rear Axle Mopar Synthetic Gear and Axle Lubr.
Body Component Fluid, Lubricant, or Genuine Part Hinges: Door , T runk & Hood Springs and Links Mopar 威 Spray White Lube or equivalent. Latches: Door , Hood & T runk Mopar 威 Multi-Purpose Lube NLGI Grade 2 or equivalent. Door Hinge Check Spring Lubriplate Mo-Lith No.
I n f o r m a t i o n P r o v i d e d b y :.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 2 2 6 䡵 Maintenance Schedules ................... 2 2 6 ▫ Schedule “B” .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system.
• T axi, police, or delivery service (commercial ser- vice). 〫 • Off-r oad or desert operation. • If equipped for and operating with E-85 (ethanol) fuel.
At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut of f. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark.
SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions.
Miles 3,000 6,000 9,000 12,000 15,000 18,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) (30 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Inspect the brake linings. X Change the front and rear axle fluid.
Miles 21,000 24,000 27,000 30,000 33,000 36,000 (Kilometers) (35 000) (40 000) (45 000) (50 000) (55 000) (60 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Lubricate the front and rear suspension ball joints. X Inspect the brake linings.
Miles 39,000 42,000 45,000 48,000 51,000 54,000 (Kilometers) (65 000) (70 000) (75 000) (80 000) (85 000) (90 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Lubricate the front and rear suspension ball joints. X Inspect the brake linings.
Miles 57,000 60,000 63,000 66,000 69,000 72,000 (Kilometers) (95 000) (100 000) (105 000) (1 10 000) (115 000) (120 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Lubricate the front and rear suspension ball joints.
Miles 75,000 78,000 81,000 84,000 87,000 90,000 (Kilometers) (125 000) (130 000) (135 000) (140 000) (145 000) (150 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Lubricate the front and rear suspension ball joints.
Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX Inspect the brake linings. X Change the front and rear axle fluid.
SCHEDULE “A” Miles 6,000 12,000 18,000 24,000 30,000 36,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) (60 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Change the front and rear axle fluid.
Miles 42,000 48,000 54,000 60,000 66,000 (Kilometers) (70 000) (80 000) (90 000) (100 000) (110 000) [Months] [42] [48] [54] [60] [66] Change engine oil and engine oil filter . X X X X X Inspect the brake linings. X Change the front and rear axle fluid.
Miles 72,000 78,000 84,000 90,000 96,000 102,000 (Kilometers) (120 000) (130 000) (140 000) (150 000) (160 000) (170 000) [Months] [72] [78] [84] [90] [96] [102] Change engine oil and engine oil filter . X XXXXX Inspect the brake linings. X X Inspect and replace, if necessary , the engine air cleaner filter .
* This maintenance is recommended by DaimlerChrysler Corporation to the owner but is not requir ed to maintain the warranty on the PCV orifice. ‡ This maintenance is not r equired if previously replaced. Inspection and service should also be performed anytime a malfunction is observed or suspected.
I n f o r m a t i o n P r o v i d e d b y :.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 2 4 2 ▫ Prepar e For The Appointment ............ 2 4 2 ▫ Prepar e A List ........................ 2 4 2 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional char ges with the service manager .
technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner . This is why you should always talk to your dealer’s service manager first.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center .
W ARRANTY INFORMA TION (U.S. V ehicles Only) See the W arranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer .
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Call T oll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orld Wide W eb at: • www .techauthority .
T raction Grades The traction grades, from highest to lowest, are A, B, and C, and they repr esent the tire’s ability to stop on wet pave- ment as measured under contr olled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
INDEX 10 I n f o r m a t i o n P r o v i d e d b y :.
About Y our Brakes ....................... 1 2 5 ABS (Anti-Lock Brake) System ............... 9 1 Accessory Delay , Power .................. 14,28 Adding Engine Coolant (Antifreeze) .......... 1 9 2 Adding Fuel ........................... 1 5 2 Adding W asher Fluid .
Emergency Starting ..................... 1 5 8 Gas Caution .......................... 1 8 1 Jump Starting ......................... 1 5 8 Keyless T ransmitter Replacement ............ 2 0 Bearings .............................. 2 0 0 Belt System, Six Point .
Chains, T ire ............................ 1 4 7 Charging System Light ..................... 9 4 Chart, T ire Sizing ........................ 1 3 1 Check Engine Light (Malfunction Indicator Light) . 170 Checks, Safety ........................... 5 3 Child Restraint .
Defroster , W indshield ...................... 5 3 Delay (Intermittent) W ipers ................. 8 5 Diagnostic System, Onboard ................ 1 6 9 Dimmer Control ......................... 7 7 Dimmer Switch, Headlight .................. 8 0 Disposal Antifreeze (Engine Coolant) .
Engine Oil V iscosity ................... 174,220 Engine Oil V iscosity Chart ................. 1 7 4 Exhaust Gas Caution .............. 26,53,151,189 Exhaust System ......................... 1 8 9 Exterior Lights ....................... 2 1 1,212 F a n .
Fueling ............................... 1 5 2 Fuses ................................ 2 0 3 G a s C a p .............................. 1 5 2 Gasoline .............................. 1 4 8 Gasoline, Clean Air ...................... 1 4 9 Gasoline, Reformulated .
Infant Restraint .......................... 3 6 Inside Rearview Mirror .................... 6 9 Instrument Cluster ........................ 9 0 Instrument Panel and Controls ............... 8 9 Instrument Panel Lens Cleaning ............. 2 0 1 Interior and Instrument Lights .
Headlights ......................... 78,214 High Beam ........................... 8 0 High Beam Indicator .................... 9 3 Instrument Cluster ...................... 7 8 Interior ............................ 76,77 License ......................
Message Center .......................... 9 1 Mirrors ................................ 6 9 Electric Remote ........................ 7 0 Outside .............................. 7 0 Rearview ............................. 6 9 Modifications/Alterations, V ehicle .
Power Accessory Delay ...................... 14,28 Brakes .............................. 1 2 5 Distribution Center ..................... 2 0 3 Steering .......................... 129,185 W indows ............................. 2 7 Pregnant W omen and Seat Belts .
Safety Defects, Reporting .................. 2 4 5 Safety , Exhaust Gas ....................... 2 6 Safety Information, T ire ................... 1 3 0 Safety T ips ............................. 5 3 Satellite Radio .......................... 1 0 6 Satellite Radio Antenna .
Speedometer ............................ 9 0 Starting ............................... 1 1 9 Emergency (Jump Starting) ............... 1 5 8 Engine Fails to Start .................... 1 2 0 Starting and Operating .................... 1 1 9 Steering Linkage .
Spinning ............................ 1 4 2 Storage ............................. 1 4 7 T read W ear Indicators ................... 1 4 2 T op Cover .............................. 6 1 T owing ............................ 153,163 Disabled V ehicle ....
W arranty Information ..................... 2 4 5 W asher , Adding Fluid ..................... 1 8 9 W ashers, W indshield ................... 84,189 Wheel Alignment and Balance ............... 1 4 5 Wheel Bearings ......................... 2 0 0 W ind Buffeting .
264 INDEX I n f o r m a t i o n P r o v i d e d b y :.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Dodge Viper (2006) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Dodge Viper (2006) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Dodge Viper (2006), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Dodge Viper (2006) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Dodge Viper (2006), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Dodge Viper (2006).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Dodge Viper (2006). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Dodge Viper (2006) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
