Manuel d'utilisation / d'entretien du produit Dart (2015) du fabricant Dodge
Aller à la page of 658
Dart Chrysler Group LLC O W N E R ’ S M A N U A L 2015 2 0 1 5 D a r t 15PFD41-126-AA First Edition Printed in U.S.A. I n f o r m a t i o n P r o v i d e d b y :.
VEHICLES SOLD IN CANADA W ith respect to any V ehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor e. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE . . . . . . .
I n f o r m a t i o n P r o v i d e d b y :.
INTRODUCTION CONTENTS ! INTRODUCTION ........................ 4 ! HOW TO USE THIS MANUAL .............. 4 ! W ARNINGS AND CAUTIONS .............. 6 ! VEHICLE IDENTIFICA TION NUMBER .
INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
1 INTRODUCTION 5 I n f o r m a t i o n P r o v i d e d b y :.
W ARNINGS AND CAUTIONS This Owners Manual contains W ARNINGS against op- erating procedures that could result in a collision or bodily injury . It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information.
NOTE: It is illegal to remove or alter the VIN. VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
I n f o r m a t i o n P r o v i d e d b y :.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS ! A WORD ABOUT YOUR KEYS ............. 1 2 ▫ Ignition Node Module (IGNM) — If Equipped . .12 ▫ Keyless Ignition Node (KIN) — If Equipped . . .13 ▫ Standar d Blade Ignition Key — If Equipped .
▫ T o Lock The Doors ..................... 2 5 ▫ T o Unlatch The T runk ................... 2 6 ▫ Using The Panic Alarm .................. 2 6 ▫ Pr ogramming Additional T ransmitters ....... 2 7 ▫ T ransmitter Battery Replacement ...........
! ENGINE BREAK-IN RECOMMENDA TIONS . . .109 ! SAFETY TIPS ......................... 1 1 0 ▫ T ransporting Passengers ................. 1 1 0 ▫ Exhaust Gas ......................... 1 1 1 ▫ Safety Checks Y ou Should Make Inside The V ehicle .....
A WORD ABOUT YOUR KEYS Y our vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a either a bladed key with an immobilizer chip in it, or a Key Fob with Remote Keyless Entry (RKE) transmitter and an Ignition Node Module (IGNM).
Keyless Ignition Node (KIN) — If Equipped This feature allows the driver to operate the ignition switch with the push of a button, as long as the Remote Keyless Entry (RKE) transmitter is in the passenger compartment. The Keyless Ignition Node (KIN) has four operating positions, three of which are labeled and will illuminate when in position.
Keyless Enter-N-Go™ Feature If your vehicle is equipped with the Keyless Enter-N- Go™ feature, refer to “Starting Procedur e” in “Starting And Operating” for further information. Standard Blade Ignition Key — If Equipped Y our vehicle may use a standard blade key ignition system.
Key Fob — If Equipped The Key Fob also contains the Remote Keyless Entry (RKE) transmitter and an emergency key , which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead.
NOTE: Y ou can insert the double-sided emergency key into the lock cylinders with either side up. Ignition Or Accessory On Message Opening the driver’s door when the ignition is in ACC or ON (engine not running), a chime will sound to remind you to place the ignition in the OFF position.
W ARNING! • When leaving the vehicle, always remove the Key Fob from the vehicle and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
The system uses a Key or Key Fob with Remote Keyless Entry (RKE) transmitter , an RF receiver , and either an Ignition Node Module (IGNM) or a Keyless Ignition Node (KIN) to prevent unauthorized vehicle operation. Therefor e, only Keys or Key Fobs that are programmed to the vehicle can be used to start and operate the vehicle.
CAUTION! Always remove the keys from the vehicle and lock all doors when leaving the vehicle unattended. At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secur e location.
VEHICLE SECURITY ALARM — IF EQUIPPED The V ehicle Security Alarm monitors the vehicle doors for unauthorized entry and the ignition switch for unau- thorized operation. This system may also incorporate a ultrasonic intrusion sensor that monitors for motion in the vehicle.
same exterior zone (refer to # Keyless Enter-N-Go™ # in # Things T o Know Before Starting Y our V ehicle # for further information). • Push the LOCK button on the Remote Keyless Entry (RKE) transmitter .
system will give you a false alarm. If one of the previ- ously described arming sequences has occurred, the V ehicle Security Alarm will arm regar dless of whether you are in the vehicle or not. If you remain in the vehicle and open a door , the alarm will sound.
• Y ou may need to be less than 35 ft (1 1 m) from the vehicle when using the RKE transmitter to turn off the Panic Alarm due to the radio frequency noises emitted by the system. Security System Manual Override The V ehicle Security Alarm will not arm if you lock the doors using the manual door lock plunger .
NOTE: Driving at speeds 5 mph (8 km/h) and above disables the system from responding to all RKE transmit- ter buttons for all RKE transmitters. Key Fob With Remote Keyless Entry (RKE) T ransmitter (IG.
T o Unlock The Doors Push and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door or twice within five seconds to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.
If the vehicle is equipped with Passive Entry , r efer to “Keyless Enter-N-Go™” under “Things T o Know Before Starting Y our V ehicle” for further information. Sound Horn W ith Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter .
• Y ou may need to be less than 35 ft (1 1 m) from the vehicle when using the RKE transmitter to turn off the Panic Alarm due to the radio frequency noises emitted by the system. Programming Additional T ransmitters Programming Key Fobs or RKE transmitters may be performed at an authorized dealer .
2. Separating RKE halves requir es screw removal – if equipped, and gently prying the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal.
3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar , then replace the battery .
clip, located on the back cover . A void touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery , clean it with rubbing alcohol. 4. T o assemble the RKE transmitter case, snap the two halves together , reposition and secure the scr ew as shown in step #2 for removal.
NOTE: • The vehicle must be equipped with an automatic transmission to be equipped with Remote Start. • Low fuel indicator must not be illuminated.
W ARNING! (Continued) • Keep Remote Keyless Entry (RKE) transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.
• The park lamps will turn on and remain on during Remote Start mode. • For security , power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the Remote Start mode. • The engine can be started two consecutive times (two 15-minute cycles) with the RKE transmitter .
DOOR LOCKS Manual Door Locks T o lock each door , rotate the door lock knob on each door trim panel forward. T o unlock the front doors, pull the inside door handle to the first detent or rotate the door lock button until the red indicator is visible.
W ARNING! • For personal security and safety in the event of an collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
The doors can also be locked and unlocked with the Keyless Enter-N-Go™ (Passive Entry) system. For further information, refer to “Keyless Enter-N-Go™” in “Things T o Know Before Starting Y our V ehicle”. If you push the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate.
Automatic Unlock Doors On Exit Programming T o change the current setting, refer to “Uconnect® Set- tings” in “Understanding Y our Instrument Panel” for further information. NOTE: Use the Automatic Unlock Doors On Exit feature in accordance with local laws.
NOTE: For emergency exit from the rear seats when the Child-Protection Door Lock System is engaged, manually rotate the door lock button to the unlocked position, roll down the window , and open the door using the outside door handle.
NOTE: If “Unlock All Doors 1st Push” is programmed all doors will unlock when you grab hold of the front driver ’s door handle. T o select between “Unlock Driver Door 1st Push” and “Unlock All Doors 1st Push”, refer to “Uconnect® Settings” in “Understanding Y our Instru- ment Panel” for further information.
If one of the vehicle doors is open and the door panel switch is used to lock the vehicle, once all open doors have been closed the vehicle checks the inside and outside of the vehicle for any valid Passive Entry RKE transmitters.
NOTE: If you inadvertently leave your vehicle’s Passive Entry RKE transmitter in the trunk and try to close the trunk lid, the trunk lid will automatically unlatch, unless another one of the vehicle’s Passive Entry RKE transmit- ters is outside the vehicle and within 3 ft (1.
Push The Door Handle Button T o Lock Do NOT Grab The Handle When Locking 42 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
NOTE: • After pushing the door handle button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking.
NOTE: For vehicles equipped with the Uconnect®, the power window switches will remain active for up to 10 minutes after the ignition is cycled to the OFF position. Opening either front door will cancel this feature. The time is programmable. Refer to “Uconnect® Settings” in “Under- standing Y our Instrument Panel” for further information.
Manual Down Push the switch for more than a half a second and release when you want the window to stop. Express Up Lift the switch for less than a half a second and release. The window will go up automatically . Manual Up Lift the switch for more than a half a second and release when you want the window to stop.
3. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. W indow Lockout Switch The window lockout switch on the driver’s door trim panel allows you to disable the window controls on the rear passenger doors.
Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter-type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
W ith the ignition in the ON/RUN position, the T runk Open symbol will display in the instrument cluster indicating that the trunk is open. The odometer display will reappear once the trunk is closed. W ith the ignition in the OFF position, the T runk Open symbol will display until the trunk is closed.
OCCUP ANT RESTRAINT SYSTEMS Some of the most important safety features in your vehicle are the restraint systems: • Seat Belt Systems • Supplemental Restraint Systems (SRS) Air Bags • Child Restraints Important Safety Precautions Please pay close attention to the information in this section.
2. If a child from 2 to 12 years old (not in a rear -facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint.
W ARNING! • Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger , including a child in a rear- facing child restraint. • Only use rear-facing child restraint in a vehicle with a rear seat.
After the sequence completes, the Seat Belt Reminder Light remains illuminated until the respective seat belts are buckled. The driver should instruct all other occu- pants to buckle their seat belts.
W ARNING! • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly . In some collisions, the air bags won’t deploy at all. Always wear your seat belt even though you have air bags.
W ARNING! (Continued) • A lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug.
W ARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. Y ou are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together .
3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt.
6. T o release the seat belt, push the red button on the buckle. The seat belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow the seat belt to r etract fully . Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt.
As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it is locked in position.
W ARNING! • ONL Y use a Seat Belt Extender if it is physically required in order to properly fit the original seat belt system. DO NOT USE the Seat Belt Extender if, when worn, the distance between the front edge of the Seat Belt Extender buckle and the center of the occupant’ s body is LESS than 6 inches.
The pretensioners are triggered by the Occupant Re- straint Controller (ORC). Like the air bags, the preten- sioners are single use items. A deployed pretensioner or a deployed air bag must be replaced immediately .
If the passenger seating position is equipped with an ALR and is being used for normal usage: Only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the ALR. If the ALR is activated, you will hear a clicking sound as the seat belt retracts.
3. Allow the seat belt to retract. As the seat belt retracts, you will hear a clicking sound. This indicates the seat belt is now in the Automatic Locking Mode.
• Steering Wheel and Column • Instrument Panel • Knee Impact Bolsters • Advanced Front Air Bags • Supplemental Side Air Bags • Supplemental Knee Air Bags • Fr ont and Side Impact Sensors.
W ARNING! • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury , including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.
Advanced Front Air Bag Features The Advanced Front Air Bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the Occupant Restraint Controller (ORC), which may receive information from the fr ont impact sensors or other system components.
W ARNING! (Continued) • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly . In some collisions, air bags won’t deploy at all. Al- ways wear your seat belts even though you have air bags.
W ARNING! (Continued) • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly . In some collisions, air bags won’t deploy at all. Al- ways wear your seat belts even though you have air bags.
way as the air bags inflate to their full size. The Advanced Front Air Bags fully inflate in less time than it takes to blink your eyes. The air bags then quickly deflate while helping to restrain the driver and front passenger .
The OCS will NOT prevent deployment of the Passenger Advanced Front Air Bag. The OCS may reduce the inflation rate of the Passenger Advanced Front Air Bag if the OCS estimates that: • The front pass.
W ARNING! • Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger , including a child in a rear- facing child restraint. • Only use rear-facing child restraint in a vehicle with a rear seat.
Lighter W eight Passengers (Including Small Adults) When a lighter weight passenger , including a small adult, occupies the front passenger seat, the OCS may reduce the inflation rate of the Passenger Advanced Front Air Bag. This does not mean that the OCS is working improperly .
The OCS will detect the front passenger ’s decreased or increased seated weight, which may result in an adjusted inflation rate of the Passenger Advanced Front Air Bag in a collision.
The OCS determines the front passenger ’s most probable classification. If an occupant in the front passenger seat is seated improperly , the occupant may provide an output signal to the OCS that is.
Not Seated Properly Not Seated Properly 74 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
W ARNING! • If an occupant in the front passenger seat is seated improperly , the occupant may provide an output signal to the OCS that is different from the occu- pant’ s properly seated weight input. This may result in serious injury or death in a collision.
classify the seated weight of a front seat passenger , the OCS components must function as designed. Do not make any modifications to the front passenger seat components, assembly , or to the seat cover . If the seat, trim cover , or cushion needs service for any reason, take the vehicle to your authorized dealer .
.
The SABs may help to reduce the risk of occupant injury during certain side impacts, in addition to the injury reduction potential provided by the seat belts and body structur e.
When the SAB deploys, it opens the seam on the out- board side of the seatback’s trim cover (front seats) and the seam on the outboard side of the seat cushion’s trim cover (outboard rear seats — if equipped with rear SABs). The inflating SAB deploys through the seat seam into the space between the occupant and the door .
SABICs may help reduce the risk of head injury to front and rear seat outboard occupants in certain side impacts. SABICs may reduce the risk of injuries in certain side impacts, in addition to the injury reduction potential provided by the seat belts and body structure.
The SABICs and SABs (“Side Air Bags”) are designed to activate in certain side impacts. The Occupant Restraint Controller (“ORC”) determines whether the deployment of the Side Air Bags in a particular impact event is appropriate, based on the severity and type of collision.
be properly restrained in a child restraint or booster seat that is appropriate for the size of the child. W ARNING! • Side Air Bags need room to inflate. Do not lean against the door or window . Sit upright in the center of the seat. • Being too close to the Side Air Bags during deploy- ment could cause you to be severely injured or killed.
• As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat.
• Cut off fuel to the engine. • Flash hazard lights as long as the battery has power or until the ignition switch is turned to the “OFF” posi- tion. • T urn on the interior lights, which remain on as long as the battery has power or until the ignition switch is turned to the “OFF” position.
the ON/RUN position. After the self-check, the Air Bag W arning Light will turn off. If the ORC detects a mal- function in any part of the system, it turns on the Air Bag W arning Light, either momentarily or continuously . A single chime will sound to alert you if the light comes on again after initial startup.
Maintaining Y our Air Bag System W ARNING! • Modifications to any part of the air bag system could cause it to fail when you need it. Y ou could be injured if the air bag system is not there to protect you.
Event Data Recorder (EDR) This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per- formed.
Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the United States, and every Canadian province, requir es that small children ride in proper restraint systems. This is the law , and you can be pros- ecuted for ignoring it.
NOTE: • For additional information, refer to www .seatcheck.org or call 1–866–SEA TCHECK (732–8243). Canadian resi- dents should refer to T ransport Canada’s website for additional information: • www .tc.gc.ca/eng/roadsafety/safedrivers- childsafety-index-53.
Child Size, Height, W eight Or Age Recommended T ype Of Child Restraint Larger Children Children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehi- cl.
W ARNING! • Never place a rear-facing child restraint in front of an air bag. A deploying passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger , including a child in a rear- facing child restraint. • Only use a rear-facing child restraint in a vehicle with a rear seat.
seat. The child and belt-positioning booster seat are held in the vehicle by the seat belt. W ARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed.
2. Do the child’s knees bend comfortably over the front of the vehicle seat – while they are still sitting all the way back? 3. Does the shoulder belt cross the child’s shoulder between their neck and arm? 4. Is the lap part of the seat belt as low as possible, touching the child’s thighs and not their stomach? 5.
Recommendations For Attaching Child Restraints Restraint T ype Combined W eight of the Child + Child Restraint Use any attachment method shown with an “X” Below LA TCH – Lower Anchors Only Seat Belt Only LA TCH – Lower Anchors + T op T ether Anchor Seat Belt + T op T ether Anchor Rear-Facing Child Restraint Up to 65 lbs (29.
Lower Anchors And T ethers For Children (LA TCH) Restraint System Y our vehicle is equipped with the child restraint anchor- age system called LA TCH, which stands for Lower Anchors and T ethers for CHildren. The LA TCH system has three vehicle anchor points for installing LA TCH- equipped child seats.
LA TCH Positions For Installing Child Restraints In This V ehicle • Lower Anchorage Symbol 2 anchorages per seating position • T op T ether Anchorage Symbol 96 THINGS TO KNOW BEFORE ST ARTING YOUR.
What is the weight limit (child’s weight + weight of the child restraint) for using the LA TCH anchorage system to attach the child restraint? 65 lbs (29.5 kg) Use the LA TCH anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.
Can two child restraints be attached using a common lower LA TCH anchorage? No Never “share” a LA TCH anchorage with two or more child restraints. If the center position does not have dedicated LA.
Locating The LA TCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint.
Locating The T ether Anchorages There are tether strap anchorages behind each rear seating position located in the panel be- tween the rear seatback and the rear window .
tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center Seat LA TCH Do not install child restraints with rigid lower attach- ments in the center seating position.
1. Loosen the adjusters on the lower straps and on the tether strap of the child seat so that you can more easily attach the hooks or connectors to the vehicle anchorages. 2. Place the child seat between the lower anchorages for that seating position.
behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. Do not lock the seat belt. Remind all children in the vehicle that the seat belts are not toys and that they should not play with them.
Lap/Shoulder Belt Systems For Installing Child Restraints In This V ehicle 104 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
What is the weight limit (child’s weight + weight of the child re- straint) for using the T ether Anchor with the seat belt to attach a forward facing child restraint? W eight limit of the Child Res.
Installing A Child Restraint W ith A Switchable Automatic Locking Retractor (ALR) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit.
strap. See the section “Installing Child Restraints Using the T op T ether Anchorage” for directions to attach a tether anchor . 9. T est that the child restraint is installed tightly by pulling back and forth on the child seat at the seat belt path.
1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. Y ou may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available.
5. Remove slack in the tether strap according to the child restraint manufacturer ’s instructions. W ARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap.
While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. W ide-open throttle acceleration in low gear can be detri- mental and should be avoided. The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.
W ARNING! (Continued) • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoper- able. Floor Mat Safety Information Always use floor mats designed to fit the footwell of your vehicle.
W ARNING! (Continued) • Always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Ob- jects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly in- stalled, if not equipped from the factory .
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS ! MIRRORS ........................... .121 ▫ Inside Day/Night Mirror — If Equipped . . . .121 ▫ Automatic Dimming Mirror — If Equipped . . .122 ▫ Outside Mirrors ..................... .122 ▫ Outside Mirrors Folding Feature — If Equipped .
▫ Advanced Phone Connectivity ........... .153 ▫ Things Y ou Should Know About Y our Uconnect® Phone .................... .155 ▫ General Information .................. .166 ! Uconnect® PHONE (8.4/8.4N) ............ .167 ▫ Uconnect® 8.4/8.4Nav .
▫ Head Restraints ..................... .230 ▫ Folding Rear Seat .................... .232 ! T O OPEN AND CLOSE THE HOOD ........ .234 ! LIGHTS ............................ .236 ▫ Headlight Switch .................... .236 ▫ Automatic Headlights — If Equipped .
▫ Headlights On W ith W ipers (A vailable W ith Automatic Headlights Only) ............ .249 ▫ Rain Sensing W ipers — If Equipped ....... .249 ! TIL T/TELESCOPING STEERING COLUMN . . .251 ! HEA TED STEERING WHEEL — IF EQUIPPED . .252 ! ELECTRONIC SPEED CONTROL — IF EQUIPPED .
▫ Sunglass Bin Door ................... .274 ! GARAGE DOOR OPENER — IF EQUIPPED . . .275 ▫ Befor e Y ou Begin Programming HomeLink® . .276 ▫ Pr ogramming A Rolling Code ............ .276 ▫ Pr ogramming A Non-Rolling Code ........ .278 ▫ Canadian/Gate Operator Programming .
! ST ORAGE ........................... .292 ▫ Glove Compartment .................. .292 ▫ Console Features .................... .293 ▫ Door Storage ........................ .294 ▫ Rear Seat Armrest Storage — If Equipped . . . .295 ! CARGO AREA FEA TURES .
MIRRORS Inside Day/Night Mirror — If Equipped A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and r equires no tools for mounting.
Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. This feature will be defaulted on, and only be disabled when the vehicle is moving in reverse. CAUTION! T o avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror .
W ARNING! V ehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object.
NOTE: The approach lighting will not function when the shift lever is moved out of the P ARK position. Power Mirrors The power mirror controls are located on the drivers door trim panel. The power mirror controls consist of mirror select but- tons and a four-way mirror control switch.
Illuminated V anity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor . T o use the mirror , rotate the sun visor downward and swing the mirror cover upward. The light will turn on automati- cally . Closing the mirror cover will turn off the light.
When the vehicle is started, the BSM warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational. Automatic T ransmission V ehicles The BSM system sensors operate when the vehicle is in any forward gear or REVERSE and enters stand-by mode when the vehicle is in P ARK.
The BSM detection zone covers approximately one lane width on both sides of the vehicle 12 ft (3.8 m). The zone length starts at the outside rear view mirror and extends approximately 10 ft (3 m) beyond the rear bumper of the vehicle.
contamination so that the BSM system can function properly . Do not block the area of the rear fascia where the radar sensors are located with foreign objects (bum- per stickers, bicycle racks, etc.
Entering From The Rear V ehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Overtaking T raffic If you pass another vehicle slowly (with a relative speed of less than 15 mph (24 km/h) and the vehicle remains in the blind spot for approximately 1.
The BSM system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However , occasionally the system may alert on such objects. This is normal operation and your vehicle does not requir e service.
W ARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM (Continued) Stationary Objects Opposing T raffic 3 UNDERST ANDING THE FEA TURES OF YOU.
W ARNING! (Continued) system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder , and use your turn signal before changing lanes.
NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver .
Blind Spot Alert Lights/Chime When operating in Blind Spot Alert Lights/Chime mode, the BSM system will provide a visual alert in the appro- priate side view mirror based on a detected object. If the turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded.
General Information This vehicle has systems that operate on radio frequency that comply with Part 15 of the Federal Communications Commission (FCC) rules and with Industry Canada Standards RSS- GEN/210/220/310. Operation is subject to the following two conditions: 1.
For additional information on Uconnect®: • U.S. residents - visit DriveUconnect.com or call 1-877-855-8400. • Canadian Residents - visit DriveUconnect.
V oice Command Button When you push the V oice Command but- ton you will hear a BEEP . The beep is your signal to give a command. The Uconnect® Phone can be used with any Hands-Free Profile certified Bluetooth® mobile phone. See the Uconnect® website for supported phones.
part of the command when you are asked for it. For example, you can use the compound form voice com- mand “Phonebook New Entry”, or you can break the compound form command into two voice commands: “Phonebook” and “New Entry”.
NOTE: If other phones are present during the pairing process make sure they are switched to off or the bluetooth is disabled before proceeding. The following are general phone to Uconnect® Phone pairing instructions: • Push the Phone button to begin.
Dial By Saying A Number • Push the Phone button to begin. • After the “Ready” prompt and the following beep, say “Dial.” • The system will prompt you to say the number you want to call. • For example, you can say “234-567-8901.” • The Uconnect® Phone will confirm the phone number and then dial.
Phonebook Download — Automatic Phonebook T ransfer From Mobile Phone If equipped and specifically supported by your phone, Uconnect® Phone automatically downloads names (text names) and number entries from your mobile phone’s phonebook. Specific Bluetooth® Phones with Phone Book Access Profile may support this feature.
Add Names T o Y our Uconnect® Phonebook NOTE: Adding names to the Uconnect® Phonebook is recommended when the vehicle is not in motion. T o add names to the Uconnect® phonebook using V oice Commands: 1. Push the Phone button to begin. 2. After the “Ready” prompt and the following beep, say “Phonebook New Entry .
• Push the Phone button to begin. • After the “Ready” prompt and the following beep, say “Phonebook Edit.” • Y ou will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or other) that you wish to edit.
from which you choose. T o select one of the entries from the list, push the V oice Command button while the Uconnect® Phone is playing the desired entry and say “Delete.” 4. After you enter the name, the Uconnect® Phone will ask you which designation you wish to delete: home, work, mobile, other , or all.
Phone Call Features The following features can be accessed through the Uconnect® Phone if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this featur e can be accessed through the Uconnect® Phone.
Making A Second Call While Current Call Is In Progress T o make a second call while you are currently on a call, push the V oice Command button and say “Dial” or “Call” followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progr ess.
the second call has established, push and hold the Phone button until you hear a double beep, indi- cating that the two calls have been joined into one conference call. Call T ermination T o end a call in progress: 1. Momentarily push the Phone button.
Call Continuation Call continuation is the progression of a phone call on the Uconnect® Phone after the vehicle ignition key has been switched to OFF .
Emergency Assistance If you are in an emergency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the Uconnect® Phone is operational, you may reach the emergency number as follows: • Push the Phone button to begin.
W ARNING! T o use your Uconnect® Phone System in an emer- gency , your mobile phone must be: • turned on, • paired to the Uconnect® System, • and have network coverage. Roadside Assistance If you need roadside assistance: • Push the Phone button to begin.
Paging T o learn how to page, refer to # W orking with Automated Systems. # Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the Uconnect® Phone. V oice Mail Calling T o learn how to access your voice mail, refer to # W orking with Automated Systems.
Uconnect® Phone will then send the corresponding phone number associated with the phonebook entry , as tones over the phone. NOTE: • Y ou may not hear all of the tones due to mobile phone network configurations.
Dialing Using The Mobile Phone Keypad Y ou can dial a phone number with your mobile phone keypad and still use the Uconnect® Phone (while dialing via the mobile phone keypad, the user must exercise caution and take precautionary safety measures).
T o transfer an ongoing call from your Uconnect® Phone paired mobile phone to the Uconnect® Phone or vice versa using V oice Command: 1. Push the V oice Command button and say “T ransfer Call.
Select Another Mobile Phone This feature allows you to select and start using another phone paired with the Uconnect® Phone. • Push the Phone button to begin. • After the “Ready” prompt and the following beep, say “Setup Select Phone” and follow the prompts.
V oice T raining For users experiencing difficulty with the system recogniz- ing their voice commands or numbers, the Uconnect® Phone V oice T raining feature may be used. T o enter this training mode, follow one of the two following procedures: • Fr om outside the Uconnect® Phone mode (e.
For best performance: • Adjust the rearview mirror to provide at least ½ inch (1 cm) gap between the overhead console (if equipped) and the mirror . • Always wait for the beep before speaking. • Speak normally , without pausing, just as you would speak to a person sitting a few feet/meters away from you.
“800” must be spoken “eight-zero-zero” not “eight hun- dred.” Y ou can say “O” (letter “O”) for “0” (zero). Even though international dialing for most number com- binations is supported, some shortcut dialing number combinations may not be supported.
3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 159 I n f o r m a t i o n P r o v i d e d b y :.
160 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 161 I n f o r m a t i o n P r o v i d e d b y :.
V oice Commands Primary Alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location Primary Alternate (s) all call cancel confirmation prompts continue del.
.
V oice T ext Reply Uconnect® Phone can read or send new messages on your phone. Read Messages: If you receive a new text message while your phone is connected to Uconnect® Phone and your phone is sup- ported, an announcement will be made to notify you that you have a new text message.
List of Preset Messages: 1. Y es 2. No 3. Wher e are you? 4. I need more direction. 5. L O L 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks 1 1. See Y ou in 15 minutes 12. I am on my way 13. I’ll be late 14. Ar e you there yet? 15. Wher e are we meeting? 16.
T urn SMS Incoming Announcement ON/OFF T urning the SMS Incoming Announcement OFF will stop the system from announcing the new incoming mes- sages. • Push the Phone button. • After the “Ready” prompt and the following beep, say “Setup, SMS Incoming Message Announcement,” you will then be given a choice to change it.
Uconnect® PHONE (8.4/8.4N) Uconnect® 8.4/8.4Nav Uconnect® Phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect® Phone al- lows you to dial a phone number with your mobile phone.
• Sending a text message via the touchscreen. • Listen to Music on your Bluetooth® Device via the touchscreen. • Pairing up to 10 phones/audio devices for easy access to connect to them quickly . NOTE: Y our phone must be capable of SMS messaging via Bluetooth® for messaging features to work properly .
mobile phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s Uconnect® Phone. The Uconnect® Phone allows up to ten mobile phones or audio devices to be linked to the system. Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.
Operation V oice commands can be used to operate the Uconnect® Phone and to navigate through the Uconnect® Phone menu structure. V oice commands are requir ed after most Uconnect® Phone prompts. There are two general meth- ods for how V oice Command works: 1.
Natural Speech Y our Uconnect® Phone V oice system uses a Natural Language V oice Recognition (VR) engine. Natural speech allows the user to speak commands in phrases or complete sentences. The system filters out certain non-word utterances and sounds such as “ah” and “eh.
Cancel Command At any prompt, after the beep, you can say “Cancel” and you will be returned to the main menu. Y ou can also push the Phone or V oice Command button on your steering wheel when the system is listening for a command and be returned to the main or previous menu.
3. Select “Y es” to begin the pairing process. Then, search for available devices on your Bluetooth® enabled mobile phone. When prompted on the phone, enter the name and PIN shown on the Uconnect® screen. • If “No” is selected, press the “Settings” button from the Uconnect® Phone main screen.
5. When the pairing process has successfully completed, the system will prompt you to choose whether or not this is your favorite phone. Selecting “Y es” will make this phone the highest priority . This phone will take precedence over other paired phones within range.
NOTE: For phones which are not made a favorite, the phone priority is determined by the order in which it was paired. The latest phone paired will have the higher priority .
Y ou can also use the following VR command to bring up a list of paired audio devices: • “Show Paired Phones” • “Connect My Phone” Connecting T o A Particular Mobile Phone Or Audio Device After Pairing Uconnect® Phone will automatically connect to the high- est priority paired phone and/or Audio Device within range.
3. Pr ess the settings icon button located to the right of the device name for a differ ent Phone or Audio Device than the currently connected device. 4. The options pop-up will be displayed. 5. Pr ess the “Delete Device” button on the touchscreen.
• A maximum of 2,000 entries per phone will be down- loaded and updated every time a phone is connected to the Uconnect® Phone. • Depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used.
NOTE: If the Favorites list is full, you will be asked to remove an existing favorite. 3. Fr om the Phone main screen, select Phonebook. From the Phonebook screen, select the “Favorites” button on the touchscreen and then select the “+” button on the touchscreen located to the right of the phonebook recor d.
T o Remove A Favorite 1. T o remove a Favorite, select phonebook from the Phone main screen. 2. Next select Favorites on the left side of the screen and then press the “+” Options button on the touchscreen. 3. Pr ess the “+” next to the Favorite you would like to remove.
Emergency And T owing Assistance The Emergency and T owing Assistance Favorite numbers can only be altered. These cannot be deleted and the names cannot be changed. T o change the Emergency or T owing Assistance numbers follow these steps. 1. Pr ess the “Phonebook” button from the Phone main screen.
Phone Call Features The following features can be accessed through the Uconnect® Phone if the feature(s) are available and supported by Bluetooth® on your mobile service plan. For example, if your mobile service plan provides three- way calling, this feature can be accessed through the Uconnect® Phone.
3. The Uconnect® Phone will dial the number associated with John Doe, or if there are multiple numbers it will ask which number you want to call for John Doe.
Recent Calls Y ou may browse up to 34 of the most recent of each of the following call types: • Incoming Calls • Outgoing Calls • Missed Calls • All Calls These can be accessed by pressing the “recent calls” button on the touchscreen on the Phone main screen.
Answer Or Ignore An Incoming Call — No Call Currently In Progress When you receive a call on your mobile phone, the Uconnect® Phone will interrupt the vehicle audio sys- tem. Push the “Phone” button on the steering wheel to accept the call. Y ou can also press the “answer” button on the touchscreen or press the caller ID box.
T oggling Between Calls If two calls are in progr ess (one active and one on hold), press the “Swap” button on the Phone main screen. Only one call can be placed on hold at a time. Y ou can also push the “Phone” button to toggle between the active and held phone call.
Uconnect® Phone Features Emergency Assistance If you are in an emergency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the Uconnect® Phone is operational, you may reach the emergency number as follows: 1.
Roadside Assistance/T owing Assistance If you need roadside/towing assistance: 1. Push the Phone button to begin. 2. After the “Listening” prompt and the following beep, say “Roadside Assistance” or say “T owing Assis- tance.
numbers, is also to be used for navigating through an automated customer service center menu structur e, and to leave a number on a pager . Y ou can also send stored mobile phonebook entries as tones for fast and easy access to voice mail and pager entries.
Barge In — Overriding Prompts The V oice Command button can be used when you wish to skip part of a prompt and issue your voice command immediately .
Dialing Using The Mobile Phone Keypad W ARNING! Driving while distracted can result in loss of vehicle control, accident and injury . It is strongly recom- mended that you use extreme caution when using any device or feature that may take your focus off the road or your hands off the steering wheel.
Mute/Un-Mute (Mute ON/OFF) When you mute the Uconnect® Phone, you will still be able to hear the conversation coming from the other party , but the other party will not be able to hear you. T o mute the Uconnect® Phone simply press the “Mute” button on the Phone main screen.
• Speak normally , without pausing, just as you would speak to a person sitting a few feet/meters away from you. • Ensur e that no one other than you is speaking during a voice command period.
Far End Audio Performance Audio quality is maximized under: • Low-T o-Medium Blower Setting • Low-T o-Medium V ehicle Speed • Low Road Noise • Smooth Road Surface • Fully Closed W indows •.
NOTE: Uconnect® Phone SMS is only available when the vehicle is not moving. Read Messages: If you receive a new text message while your phone is connected to Uconnect® Phone, an announcement will be made to notify you that you have a new text message.
Once a message is received and viewed or listened to, you will have the following options: • Send a Reply • Forwar d • Call Send Messages Using Buttons On The T ouchscreen: Y ou can send messages using Uconnect® Phone. T o send a new message: 1.
4. If multiple numbers are available for the contact select which number you would like to have the message sent. 5. Pr ess “Send” or “Cancel.” Send Messages Using V oice Commands: 1. Push the Phone button. 2. After the “Listening” prompt and the following beep, say “Send message to John Smith mobile.
After the system confirms that you want to send your message to John Smith, your message will be sent. List of Preset Messages: 1. Y es. 2. No. 3. Okay . 4. I can’t talk right now . 5. Call me. 6. I’ll call you later . 7. I’m on my way . 8. Thanks.
1 1. See you in <number> minutes. 12. Stuck in traffic. 13. Start without me. 14. Wher e are you? 15. Ar e you there yet? 16. I need directions. 17. I’m lost. 18. See you later . Bluetooth® Communication Link Mobile phones have been found to lose connection to the Uconnect® Phone.
V oice T ree 200 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
NOTE: 1. Y ou can replace “John Smith” with any name in your mobile or favorite phone book. Y ou can also say “Send a message to John Smith” and the system will ask you which phone number you want to send a message to for John Smith. 2. Y ou can replace “Mobile” with “Home,” “W ork” or “Other .
202 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
NOTE: 1. Y ou can replace “John Smith” with any name in your mobile or favorite phone book. Y ou can also say “Send a message to John Smith” and the system will ask you which phone number you want to send a message to for John Smith. 2. Y ou can replace “Mobile” with “Home,” “W ork” or “Other .
204 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
NOTE: A vailable V oice Commands are shown in bold face and underlined in the gray shaded boxes. General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada.
W ARNING! (Continued) laws, including laws regarding phone use. Y our at- tention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When you push the V oice Command button, you will hear a beep.
Commands The V oice Command system understands two types of commands, Universal commands and Local commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing The V olume 1. Start a dialogue by pushing the V oice Command button.
Radio AM T o switch to the AM band, say “AM” or “Radio AM.” In this mode, you may say the following commands: • “Fr equency #” (to change the frequency) • “Next Station” (to select.
Disc Mode T o switch to the disc mode, say “Disc.” In this mode, you may say the following commands: • “T rack” (#) (to change the track) • “Next T rack” (to play the next track) • “Pr evious T rack” (to play the previous track) • “Main Menu” (to switch to the main menu) USB Mode T o switch to USB mode, say “USB.
Memo Mode T o switch to the voice recor der mode, say “Memo.” In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the recor ding, you may push the V oice Command button to stop recor ding.
• “T utorial” • “V oice T raining” NOTE: Keep in mind that you have to push the V oice Command button first and wait for the beep before speaking the “Barge In” commands.
W ARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Y our at- tention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death.
At any point, if the system does not recognize one of your commands, you will be prompted to repeat it. T o hear available commands, push the Uconnect® V oice Command button and say “Help.” Y ou will hear available commands for the screen displayed.
V oice T ree 214 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
NOTE: • Y ou can replace “950 AM” with any other AM or FM frequency , such as “98.7 FM.” • Y ou can replace “80’s on 8” with any other satellite station name received by the radio. • Y ou can replace “8” with any other satellite channel number received by the radio.
216 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
NOTE: • Y ou can replace the album, artist, song, genre, playlist, podcast and audio book names with any correspond- ing names on the current device that is playing. • Y ou can replace “8” with any track on the CD that is currently playing. Command is only available when CD is playing.
218 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
NOTE: • Y ou can replace “NFL” with any league shown on the sports league screen. For example you can say “Show MLB headlines” or “Show PGA headlines.
220 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
NOTE: • Only available with Navigation equipped vehicles. • Y ou can replace “Player” with “Radio,” “Navigation,” “Phone,” “Climate,” “More” or “Settings.” • Navigation commands only work if equipped with Navigation. NOTE: A vailable V oice Commands are shown in bold face and shaded grey .
222 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
NOTE: • Y ou can also say “Find City ,” “Find Favorite,” “Find Play by Category ,” “Find Play by Name,” “Find Re- cently Found,” “Where to?” or “Go Home.
Power Seats — If Equipped Some models may be equipped with a power driver’s seat. The power seat switch is located on the outboard side of the seat near the floor . Use the switch to move the seat up, down, forward or rearwar d. Adjusting The Seat Forward Or Rearward The seat can be adjusted both forward and rearward.
W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Power Lumbar — If Equipped V ehicles equipped with power driver or passenger seats may be equipped with power lumbar .
Manual Front Seat Forward/Rearward Adjustment On models equipped with manual seats, the adjusting bar is located at the front of the seats, near the floor . While sitting in the seat, lift up on the bar and move the seat forward or rearwar d. Release the bar once you have reached the desired position.
move forward and rearward on the seat to be sure that the seat adjusters have latched. W ARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death.
Manual Seat Height Adjustment — If Equipped The driver ’s seat height can be raised or lowered by using a lever , located on the outboard side of the seat. Pull upward on the lever to raise the seat height or push downward on the lever to lower the seat height.
NOTE: The engine must be running for the heated seats to operate. V ehicles Equipped W ith Remote Start On models that are equipped with remote start, the heated seats can be programed to come on during a remote start. This feature can be programmed through the Uconnect® system.
Head Restraints Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear .
NOTE: The head restraints should only be removed by qualified technicians, for service purposes only . If either of the head restraints require removal, see your autho- rized dealer . W ARNING! Do not place items over the top of the Reactive Head Restraint, such as coats, seat covers or portable DVD players.
T o raise the head restraint, pull upward on the head restraint. T o lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. Folding Rear Seat The rear seatbacks can be folded forward to provide an additional storage area.
After releasing the seatback, it can be folded forward. When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap.
W ARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper sta- bility for child seats and/or passengers. An improp- erly latched seat could cause serious injury .
3. Lift upward on the hood prop rod to release it from the stowage retainer . 4. Place the hood prop rod in the hood slot to secure the hood in the open position.
CAUTION! T o prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 6 in (15 cm), and then drop it. This should (Continued) CAUTION! (Continued) secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
operation of the headlights, parking lights, instrument panel lights, instrument panel light dimming, interior lights and fog lights. Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation.
Headlights On With Wipers (A vailable With Automatic Headlights Only) When this feature is active, the headlights will turn on after the wipers are turned on if the headlight switch is placed in the AUTO position and programmable feature is set to ON.
Automatic High Beam Headlamp Control — If Equipped The Automatic High Beam Headlamp Control system provides increased forward lighting at night by automat- ing high beam control through the use of a digital camera mounted on the inside rearview mirror .
T o Activate 1. T urn the headlight switch to the AUTO headlight position. 2. Push the multifunction lever away from you (toward front of vehicle) to engage the high beam mode. NOTE: This system will not activate until the vehicle is at or above 15 mph (24 km/h).
Fog Lights — If Equipped The front fog light switch is built into the headlight switch. T o activate the front fog lights, turn on the parking lights or the low beam headlights and press the headlight switch. T o turn off the front fog lights, either press the headlight switch a second time or turn off the headlight switch.
Multifunction Lever The multifunction lever controls the operation of the turn signals, headlight beam selection and passing lights. The multifunction lever is located on the left side of the steering column.
Lane Change Assist T ap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam.
The lights also turn on when a door is opened. The lights will also turn on when the UNLOCK button on the RKE is pressed. Interior Lights The interior lights come on when a door is opened. T o protect the battery , the interior lights will turn off automatically 10 minutes after the ignition is moved to the LOCK position.
W ith the parking lights or headlights on, rotating the left dimmer control upward will increase the brightness of the instrument panel lights. Ambient Light Control — If Equipped Rotate the right d.
Dome Light Position Rotate the left dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position. Interior Light Defeat (OFF) Rotate the left dimmer control to the extreme bottom “OFF” position.
Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause be- tween cycles desirable. Rotate the end of the multifunc- tion lever to the first detent position, and then turn the end of the lever to select the desired delay interval.
Mist Feature Rotate the end of the lever downward to the Mist position to activate a single wipe cycle to clear off road mist or spray from a passing vehicle.
Headlights On With Wipers (A vailable With Automatic Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the headlight switch is placed in the AUTO position.
NOTE: • The Rain Sensing feature will not operate when the wiper speed is in the low or high position. • The Rain Sensing feature may not function properly when ice or dried salt water is present on the wind- shield. • Use of Rain-X® or products containing wax or silicone may reduce rain sensor performance.
TIL T/TELESCOPING STEERING COLUMN This featur e allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column.
HEA TED STEERING WHEEL — IF EQUIPPED The steering wheel contains a heating element that helps warm your hands in cold weather . The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on it will operate for up to 80 minutes before automatically shutting of f.
W ARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaus- tion, or other physical conditions must exercise care when using the steering wheel heater .
NOTE: In order to ensur e proper operation, the Elec- tronic Speed Control system has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control system can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed.
For Premium Clusters Only • When set to analog mode: The red outer line on the speedometer changes from red to white to identify set speed. T o Deactivate A soft tap on the brake pedal, pushing the CANCEL button, or normal brake pressure while slowing the vehicle will deactivate Electronic Speed Control without erasing the set speed memory .
The drivers preferr ed units can be selected through the instrument panel settings if equipped. Refer to “ Under- standing Y our Instrument Panel” for more information. The speed increment shown is dependant on the chosen speed unit of U.S. (mph) or Metric (km/h): U.
• If the button is continually pressed, the set speed will continue to decrease until the button is released, then the new set speed will be established. Metric Speed (km/h) • Pr essing the SET (-) button once will result in a 1 km/h decrease in set speed.
P ARKSENSE® REAR P ARK ASSIST — IF EQUIPPED The ParkSense® Rear Park Assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.
ParkSense® Display When the vehicle is in REVERSE, the warning display will turn ON indicating the system status. The system will indicate a detected obstacle by showing a single arc in one or more regions based on the obstacle’s distance and location relative to the vehicle.
vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the sound tone will change from slow , to fast, to continuous.
Slow T one Slow T one 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 261 I n f o r m a t i o n P r o v i d e d b y :.
Fast T one Fast T one 262 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
Fast T one Continuous T one 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 263 I n f o r m a t i o n P r o v i d e d b y :.
The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting .
W ARNING ALER TS Rear Dis- tance (in/cm) Greater than 79 in (200 cm) 79-59 in (200-150 cm) 59-47 in (150-120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) Less than 12 in (30 cm) .
Enabling And Disabling ParkSense® ParkSense® can be enabled and disabled using the Uconnect® System. The available choices are: Off, Sound Only , or Sound and Display . Refer to “Uconnect® Set- tings” in “Understanding Y our Instrument Panel” for further information.
fascia/bumper is clean and clear of snow , ice, mud, dirt or other obstruction and then cycle the ignition. If the message continues to appear , see an authorized dealer . If “P ARKSENSE UNA V AILABLE SER VICE REQUIRED” appears in the DID, see an authorized dealer .
cycle, and it will display the # P ARKSENSE SYSTEM DIS- ABLED # message. If “P ARKSENSE SYSTEM DISABLED” appears in the DID, cycle the ignition. If the message appears again, see an authorized dealer . Cleaning The ParkSense® System Clean the ParkSense® sensors with water , car wash soap and a soft cloth.
• When you move the shift lever to the REVERSE position and ParkSense® is turned OFF , the DID will display “P ARKSENSE OFF” message for as long as the vehicle is in REVERSE. • Clean the ParkSense® sensors regularly , taking care not to scratch or damage them.
W ARNING! • Drivers must be careful when backing up even when using ParkSense®. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up.
P ARKVIEW® REAR BACK UP CAMERA — IF EQUIPPED Y our vehicle may be equipped with the ParkV iew® Rear Back Up Camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE.
The following table shows the approximate distances for each zone: Zone Distance to the rear of the vehicle Red 0 - 1 ft (0 - 30 cm) Y ellow 1 ft - 3 ft (30 cm - 1 m) Green 3 ft or greater (1 m or greater) W ARNING! Drivers must be careful when backing up even when using the ParkV iew® Rear Back Up Camera.
CAUTION! (Continued) • T o avoid vehicle damage, the vehicle must be driven slowly when using ParkV iew® to be able to stop in time when an obstacle is seen. It is recom- mended that the driver look frequently over his/her shoulder when using ParkV iew®.
Front Map/Reading Lights Lights are mounted in the overhead console. Each light can be turned on by pressing the lens. T o turn the lights off, press the lens a second time. The lights also turn on when a door is opened. The lights will also turn on when the UNLOCK button on the RKE is pressed.
GARAGE DOOR OPENER — IF EQUIPPED HomeLink® replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink® unit operates off your vehicle’s battery .
Before Y ou Begin Programming HomeLink® Be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio.
1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view . 3. Simultaneously push and hold both the HomeLink® button you want to program and the hand-held trans- mitter button.
Firmly push and release the “LEARN” or “TRAIN- ING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. NOTE: Y ou have 30 seconds in which to initiate the next step after the LEARN button has been pushed.
2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you would like to program while keeping the HomeLink® indicator light in view . 3. Simultaneously push and hold both the HomeLink® button you want to program and the hand-held trans- mitter button.
Canadian/Gate Operator Programming For programming transmitters in Canada/United States that require the transmitter signals to “time-out” after several seconds of transmission.
NOTE: • If the indicator light stays on constantly , program- ming is complete and the garage door/device should activate when the HomeLink® button is pushed. • T o program the two remaining HomeLink® buttons, repeat each step for each remaining button.
T o do this, push and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The HomeLink® Universal T ransceiver is disabled when the V ehicle Security Alarm is active.
W ARNING! (Continued) that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety fea- tures. Call toll-free 1-800-355-3515 or , on the Internet at HomeLink.
POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. W ARNING! • Never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location accessible to children.
W ARNING! (Continued) • Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object, to project through the sunroof opening. Injury may result. Opening Sunroof — Express Press the switch rearward and release it within one-half second.
Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruc- tion if this occurs.
open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window .
CAUTION! • Do not exceed the maximum power of 160 W atts (13 Amps) at 12 V olts. If the 160 W att (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.
W ARNING! T o avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 V olt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e., cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.
CUPHOLDERS Front Seat Cupholders The cupholders are located in the center console forward of the armrest between the front seats. Rear Seat Cupholders The rear seat cupholders are located in the center armrest between the rear seats.
STORAGE Glove Compartment The glove compartment is located on the passenger side of the instrument panel. Pull on the release handle to open the glove compartment.
Console Features An open storage area, or cubby bin, is located in the center console forward of the shift lever . There is a storage compartment located under the center console armrest. If equipped, the 12 V olt power outlet, USB and Aux jack are located here.
Door Storage The door panels contain storage areas. Front Door T rim Storage Rear Door T rim Storage 294 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
Rear Seat Armrest Storage — If Equipped For rear passengers there is a storage bin located in the armrest. Lift upward on the latch to open the storage compartment. CARGO AREA FEA TURES Cargo Area — 60/40 Split-Folding Rear Seat — If Equipped The 60/40 split-folding rear seat provides cargo-carrying versatility .
After releasing the seatback, it can be folded forward. When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap.
W ARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper sta- bility for child seats and/or passengers. An improp- erly latched seat could cause serious injury .
Ski Pass-Through There is a ski pass-through door located behind the rear seat armrest that allows longer items, such as snow skis, to be stored in the rear cargo area. Lower the armrest and pull downward on the latch to open the ski pass-through door .
CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window . Do not use abrasive window cleaners on the interior surface of the window . Use a soft cloth and a mild washing solution, wiping parallel to the heating elements.
I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS ! INSTRUMENT P ANEL FEA TURES ......... .304 ! INSTRUMENT CLUSTER — BASE (EVIC) .... .305 ! INSTRUMENT CLUSTER — PREMIUM ANALOG (DID) ....................... .306 ! INSTRUMENT CLUSTER — PREMIUM DIGIT AL (DID) .
▫ Operating Instructions — Radio Mode ...... .367 ▫ Operation Instructions — CD MODE For CD And MP3 Audio Play .................. .372 ▫ Notes On Playing MP3 Files ............ .374 ▫ Enter/Br owse Button (CD Mode For MP3/WMA Play) .......
! RADIO OPERA TION AND MOBILE PHONES ........................... .389 ! CLIMA TE CONTROLS .................. .390 ▫ Manual Heating And Air Conditioning — If Equipped .......................... .390 ▫ Uconnect® 8.4 Climate Controls — If Equipped .
INSTRUMENT P ANEL FEA TURES 1— A i rD e m i s t e r 5—G l o v eC o m p a r t m e n t 9—T r u n kR e l e a s e 2 — Outlet 6 — Climate Control Hard Controls/ Uconnect® System Hard Controls 10.
INSTRUMENT CLUSTER — BASE (EVIC) Electronic V ehicle Information Center (EVIC) Equipped 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 305 I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER — PREMIUM ANALOG (DID) Driver Information Display (DID) Equipped 306 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER — PREMIUM DIGIT AL (DID) Driver Information Display (DID) Equipped 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 307 I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER DESCRIPTIONS 1. T achometer This gauge measures engine revolutions-per-minute (RPM x 1000). 2. T ire Pressur e Monitoring T elltale Light — If Equipped Each tire, including the sp.
approximately one minute and then remain continuously illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended.
4. T emperature Gauge The temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily . The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather , up mountain grades, or when towing a trailer .
light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as possible to have the problem diagnosed and corrected.
For vehicles equipped with a premium cluster this indi- cator will display in the DID. Refer to ”Driver Informa- tion Display (DID) — If Equipped” for further information. 8. High Beam Indicator This indicator shows that the high beam head- lights are on.
and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system.
The light also will turn on when the parking brake is applied with the ignition is placed in the ON/RUN position. NOTE: This light shows only that the parking brake is applied.
your vehicle may require towing. The light will come on when the ignition is first placed in the ON/RUN position and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer . 16.
20. Low Fuel Light When the fuel level reaches approximately 3.0 gal (1 1.0 L) this light will turn on, and remain on until fuel is added. 21. Park/Headlight ON Indicator — If Equipped This indicator will illuminate when the park lights or headlights are turned on.
instrument cluster . For further information, refer to “Electronic V ehicle Information Center (EVIC)”. NOTE: Y ou must apply the brakes before shifting from P ARK. Driver Information Display (DID) The Driver Information Display (DID) features a driver- interactive display that is located in the instrument cluster .
25. Anti-Lock Brake (ABS) Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON/RUN position and may stay on for as long as four seconds.
CAUTION! Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the engine control system. It also could affect fuel economy and driveability . If the MIL is flashing, severe catalytic converter damage and power loss will soon occur .
W ARNING! If you continue operating the vehicle when the T ransmission T emperature W arning Light is illumi- nated you could cause the fluid to boil over , come in contact with hot engine or exhaust components and cause a fire.
31. Red Driver Information Display (DID) Reconfigu- rable T elltales This area will show reconfigurable red telltales (Door(s) Ajar , Oil Pressure W arning T elltale, Charging System T elltale, Electronic Throttle Control (ETC) T elltale, Engine T emperatur e W arning T elltale, Electric Power Steering Malfunction).
• Unstor ed Messages Until RUN These messages deal primarily with the Remote Start feature. This message type is displayed until the ignition is in the RUN state. Examples of this message type are # Remote Start Aborted - Door Ajar # and # Press Brake Pedal and Push Button to Start # .
• Settings • Units • Language The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: Electronic V ehicle Information Center EVIC EVIC .
• UP Arrow Button Push and release the UP arrow button to scroll upward through the main menus (Odometer , Digital V ehicle Speed, T rip Info, Range T o Empty , A verage Fuel Economy , Current Fuel Economy , Stored Messages, Settings).
• Service Air Bag W arning Light • W asher Fluid Low • Parking Brake Engaged • Brake Fluid Low • Service Electronic Braking System • Engine T emperature Hot • Battery V oltage Low • Oi.
• Cruise Set T o XXX km/h • Driver Seatbelt Unbuckled • Passenger Seatbelt Unbuckled • Fr ont Seatbelts Unbuckled • Door Open • Doors Open • T runk Open • Remote Start Aborted Fuel Low.
• Oil Life • Settings • Units • Language NOTE: For features in the EVIC that can be reset (A verage Fuel Economy), the EVIC prompts a reset with a RIGHT arrow button graphic and the word RESET next to it. T rip Info Push and release the UP arrow button until the T rip Info icon is highlighted in the EVIC.
Resetting A T rip Info Function T o Reset any of the three T rip Info functions, select the function you want to reset using the UP button. Push the RIGHT arrow button until the feature display zero. Range T o Empty (R TE) Shows the estimated distance that can be traveled with the fuel remaining in the tank.
T ire PSI Push and release the UP button until # T ir e Pressure # is displayed. T ire pressur e information is displayed as follows: • If tire pressure is OK for all tires, a vehicle graphic is displayed with tire pressur e values in each corner or the graphic.
Oil Change Indicator • Y our vehicle is equipped with an engine oil change indicator system. The “Oil Change Due” message will display in the EVIC display for approximately 10 seconds after a single chime has sounded, to indicate the next scheduled oil change interval.
Using The EVIC Menu V ehicles Equipped W ith Passive Entry • W ithout pushing the brake pedal, push the ENGINE ST AR T/STOP button and cycle the ignition to the ON/RUN position (Do not start the engine.) • Push and release the DOWN arrow button to scroll downward through the main menu to “V e- hicle Info”.
DRIVER INFORMA TION DISPLA Y DID The DRIVER INFORMA TION DISPLA Y (DID) features an interactive display that is located in the instrument cluster . The main display area will normally display the main menu or the screens of a selected feature of the main menu.
and then returns to the previous screen. An example of this message type is # Automatic High Beams On # . Four Button DID — If Equipped This system allows the driver to select a variety of useful information by pushing the switches mounted on the steering wheel.
The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: • UP Arrow Button Push and release the UP arrow button to scroll upward through the main menu and sub- menus (Fuel Economy , T rip A, T rip B, Stored Messages, Screen Set Up).
• LEFT Arrow Button Push the LEFT arrow button to return to the main menu from an info screen or sub-menu item. DID Displays The DID displays are located in the center portion of the cluster and con.
3 — Selectable Information (Compass, T emp, Range to Empty , T rip A, T rip B, A verage MPG) 4 — Menu T itles / Odometer 5 — Menu Set (Selectable Icons) 6 — Shift Lever Status (PRNDL) 7 — Reconfigurable T elltales 9 — Sub-menu Current Position — Whenever there are sub-menus available, the position within the sub-menus is shown here.
• Service T ir e Pressur e System • Parking Brake Engaged • Brake Fluid Low • Service Electronic Braking System • Engine T emperature Hot • Service Electronic Throttle Control • Lights O.
• Fr ont Seatbelts Unbuckled • Door Open • Doors Open • T runk Open • Gear Not A vailable • Shift Not Allowed • Shift to Neutral then Drive or Reverse • Autostick Unavailable Service Required • Automatic Unavailable Use Autostick Service Req.
• W indshield W asher Fluid Low Indicator This telltale will turn on to indicate the wind- shield washer fluid is low . • T ransmission T emperature W arning T elltale — If Equipped This telltale indicates that the transmission fluid temperature is running hot.
DID Red T elltales This area will show reconfigurable red telltales. These telltales include: • Door Ajar This telltale turns on when one or more doors are ajar . The telltale will show which doors are ajar . • Oil Pressure W arning T elltale This telltale indicates low engine oil pressure.
• If a problem is detected, the telltale will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the P ARK position. The telltale should turn off. • If the telltale remains lit with the engine running, your vehicle will usually be drivable.
DID Green T elltales • Electr onic Speed Control SET This telltale will illuminate green when the electronic speed control is SET . For further information, refer to “Electronic Speed Con- trol” in “Understanding The Features Of Y our V ehicle.
V ehicle Info Push and release the UP or DOWN arrow button until the V ehicle Info icon is highlighted in the DID. Push and release the RIGHT arrow to scr oll thr ough the following information sub-me.
The DID has the capability of displaying an interactive flower through the Fuel Economy sub-menu which will add one flower petal for every 2.5 Miles Per Gallon (MPG) (1.06 km per liter (km/l) increment. Once the vehicle reached 30 MPG the DID will display a full flower .
Fuel Economy MPG Flower Analog Display Fuel Economy MPG Flower Digital Display 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 345 I n f o r m a t i o n P r o v i d e d b y :.
T rip A Push and release the UP or DOWN arrow button until the T rip A icon/title is highlighted in the DID. The T rip A information will display the following: • Distance mi or km/h • A verage. mpg or L/100km • Elapsed T ime Hold the RIGHT arrow button to reset all the informa- tion.
Stored Messages Push and release the UP or DOWN arrow button until the Messages display icon is high- lighted in the DID. This feature shows the number of stored warning messages. Pushing the RIGHT arrow button will allow you to see what the stored messages are.
NOTE: The Scr een Setup items are only available at speeds less than 5 mph (8 km/h). All other menu items are not active when in Screen Setup. If the vehicle is shifted into gear , this feature is locked out and the main screen will display “Screen Setup Unavailable While In Motion”.
T ime Range T o Empty (RTE) A verage MPG Current MPG T rip A T rip B • Lower Left None (default setting) Compass Outside T emp T ime • Lower Right None (default setting) Compass Outside T emp T im.
• Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position or cycle the ignition to the ON/RUN position if equipped with Keyless Enter-N-Go™. T o turn off the message temporarily , push and release the MENU button.
• Push and hold the DOWN arrow button to reset the gauge and numeric display to 100% for ”Oil Life.” • Push and release the Up arrow button to exit the DID screen. V ehicles Not Equipped W ith Passive Entry • W ithout pushing the brake pedal, cycle the ignition to the ON/RUN position (Do not start the engine.
there is a Scroll/Enter control knob located on the right side of the Climate Controls in the center of the instru- ment panel. T urn the control knob to scroll through menus and change settings (i.e., 30, 60, 90), press the center of the control knob one or more times to select or change a setting (i.
Display After pressing the Display button on the touchscreen the following settings will be available. • Display Mode When in this display you may select one of the auto display settings. T o change Mode status, press and re- lease the Day , Night or Auto button on the touchscreen.
has been selected. Press the back arrow button on the touchscreen to return to the previous menu. • Units When in this display , you may select to have the EVIC, odometer , and navigation system (if equipped) changed between US and Metric units of measure.
Clock After pressing the Clock button on the touchscreen the following settings will be available. • Sync With GPS T ime — If Equipped When in this display , you may automatically have the radio set the time.
• Show T ime In Status Bar — If Equipped When in this display , you may turn on or shut off the digital clock in the status bar . T o change the Show T ime Status setting press the “Show T ime in Status Bar” button on the touchscreen until a check-mark appears next to setting, indicating that the setting has been selected.
NOTE: If your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is not damaged, the sensor may have become misaligned. T ake your vehicle to an authorized dealer to verify sensor alignment. Having a sensor that is misaligned will result in the BSM not operating to specification.
make your selection, press the Interior Accent Lighting button on the touchscreen, until a check-mark appears next to setting, showing that setting has been selected.
• Daytime Running Lights When this feature is selected, the headlights will turn on whenever the engine is running. T o make your selection, press the Daytime Running Lights button on the touch- screen, until a check-mark appears next to setting, show- ing that setting has been selected.
press the Flash Lights W ith Lock button on the touch- screen, until a check-mark appears next to setting, indicat- ing that the setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu. • Sound Horn With Lock When this feature is selected, the horn will sound when the remote start is activated.
NOTE: If the vehicle is programmed 1st Press Of Key Fob Unlocks, all doors will unlock no matter which Passive Entry equipped door handle is grasped. If 1st Press Of Key Fob Unlocks is programmed, only the driver ’s door will unlock when the driver ’s door is grasped.
Auto-On Comfort & Remote Start After pressing the Auto-On Comfort & Remote Start button on the touchscreen the following settings will be available. • Horn With Remote Start When this feature is selected, the horn will sound when the remote start is activated.
• Headlight Off Delay When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. T o change the Headlight Off Delay status press the “+” or “–” button on the touchscreen to select your desired time interval.
• Perform Compass Calibration Press the Calibration button on the touchscreen to change this setting. This compass is self-calibrating, which elimi- nates the need to manually reset the compass. When the vehicle is new , the compass may appear erratic and the EVIC will display CAL until the compass is calibrated.
• Music Info Cleanup This feature helps organize music files for optimized music navigation. T o make your selection, press the Music Info Cleanup button on the touchscreen, select On or Off fol- lowed by pressing the back arrow button on the touchscreen.
Press the Subscription Info button on the touchscreen to access the Subscription Information screen. W rite down the SIRIUS ID numbers for your receiver . T o reactivate your service, either call the number listed on the screen or visit the provider online.
Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON/RUN or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
3. After adjusting the hours, press the right side ENTER/ BROWSE control knob to set the minutes. The minutes will highlight. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. 5. T o exit, press the TIME button or press the BACK button to return to the previous menu.
Setting The Bass, Mid Range, T reble, Balance Or Fade T o set the Bass, Mid Range, T reble, Balance or Fade settings press the AUDIO button to access the Audio sub-menu. The Audio sub-menu can also be reached by pressing the MENU button until AUDIO appears in the display .
Press the BACK button to exit Bass, Mid Range, T reble, Balance or Fade. MENU Button Pressing the MENU button allows you to scroll between the setting sub-menus. Once the desired sub-menu set- ting is highlighted push the TUNE/SCROLL knob to select the setting.
will continue to cycle through the same song until repeat is turned Off. Repeat will be turned off once one for the following conditions are met: 1) The source is ejected 2) A different track list within that source is initiated 3) The REPEA T button is toggled OFF .
T o Set The Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory , press and hold the button (1–5) you wish to lock onto this station for three seconds.
If you insert a disc with the ignition ON/RUN and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number , and index time in minutes and seconds. Play will begin at the start of track 1.
R W/FF Push and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or R W or another CD button is pushed. The RW (Reverse) button works in a similar manner . Shuffle (SHFL) And Repeat (RPT) This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor- mally .
When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates.
• Number of files and folders - Loading times will increase with more files and folders T o increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. T o create a single-session disc, enable the “Disc at Once” option before writing to the disc.
Pressing the PLA YER button will change the mode to auxiliary device if the AUX jack is connected. NOTE: • The head unit will have no control of the AUX device. Y ou can only control the volume on the head unit. No information about the song will be displayed.
CD PLA YER — IF EQUIPPED The single disc CD player is located in the center console. NOTE: • The ignition switch must be in the ON or ACC position before the CD player will operate.
CD Player Operating Instructions Loading T o insert disc into the player , follow the instructions shown: 1. Gently insert the disc with the label facing the rear of the vehicle while the light below the loading slot is illuminated. The disc will automatically be pulled into the CD player .
Connecting The iPod® Or External USB Device Use the connection cable to connect an iPod® or external USB device to the vehicle’s USB/AUX connector port which is located in the center console.
NOTE: The center console will have a position where the iPod® or consumer electronic audio device cable can be routed through without damaging the cable when clos- ing the lid. A factory cut out space for the cable to be routed may be located in the base of the center console on either the front or side.
Controlling The iPod® Or External USB Device Using Radio Buttons T o enter the iPod®/USB/MP3 control mode and access a connected audio device, either push the “AUX” button on the radio faceplate or push the VR button and say # USB # or # Switch to USB.
• Use the << SEEK button during play mode to jump to the start of the current track. Pressing the SEEK >> button during play mode will jump to the next track in the list, or press the VR button and say # Next or Previous T rack.
• Pr essing a PRESET button will display the current list on the top line and the first item in that list on the second line. • T o exit Browse mode without making a selection, press the same PRESET button again to go back to Play mode . • Browse button: The Browse button will display the top level menu of the iPod® or external USB device.
CAUTION! (Continued) • Placing items on the iPod® or external USB device, or connections to the iPod® or external USB device in the vehicle, can cause damage to the device and/or to the connectors. W ARNING! Do not plug in or remove the iPod® or external USB device while driving.
3. Say the name of the audio device or ask the Uconnect® phone system to list the audio devices. Next T rack Use the SEEK UP button, or push the VR button on the radio and say “Next T rack,” to jump to the next music track on your cellular phone.
mode of the sound system. Pressing the top of the rocker switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will make the radio switch between the various modes available (AM/FM/SA T/ CD/HDD/AUX, etc.
CD/DVD DISC MAINTENANCE T o keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch- ing the disc.
CLIMA TE CONTROLS The air conditioning and heating system is designed to make you comfortable in all types of weather . This system can be operated through either the controls on the instrument panel or through the Uconnect® 8.4 system display if equipped.
2. Recir culation Control Pressing the Recirculation Control button will temporar- ily put the system in recir culation mode. This can be used when outside conditions such as smoke, odors, dust, or high humidity are present. Activating recir culation will cause the LED in the control button to illuminate.
NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C condenser located in front of the radiator for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser .
NOTE: The center instrument panel outlets can be aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear . • Bi-Level Air is dir ected through the panel and floor outlets. NOTE: For all settings, except full cold or full hot, there is a difference in temperature between the upper and lower outlets.
6. Electr onic Rear W indow Defrost Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indica- tor in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 15 minutes.
Uconnect® 8.4 Climate Controls — If Equipped Buttons On The Faceplate The buttons on the faceplate are located below the Uconnect® 8.4 screen, in the center of the instrument panel. Buttons On The T ouchscreen Buttons on the touchscreen are accessible on the Uconnect® 8.
Button Descriptions (Applies T o Both Buttons On The Faceplate And Buttons On The T ouchscreen) 1. MAX A/C Button Press to change the current setting, the indicator illumi- nates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
6. Rear Defrost Button Press and release this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 15 minutes.
8. Passenger T emperatur e Control Down Button Provides the passenger with independent temperature control. Press the button on the faceplate for cooler temperature settings or on the touchscreen, press and slide the button on the touchscreen temperature bar towards the blue arrow button on the touchscreen for cooler temperature settings.
1 1. Modes The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, and demist outlets. The Mode settings are as follows: • Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individu- ally adjusted to direct the flow of air .
12. Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF . 13. Driver T emperatur e Control Down Button Provides the driver with independent temperature con- trol. Push the button for cooler temperature settings.
front fascia protectors may reduce airflow to the condenser , reducing air conditioning performance. MAX A/C MAX A/C sets the control for maximum cooling perfor- mance. Press and release to toggle between MAX A/C and the prior settings. The button on the touchscreen illuminates when MAX A/C is ON.
NOTE: In cold weather , use of recirculation mode may lead to excessive window fogging. The r ecirculation feature may be unavailable (button on touchscreen greyed out) if conditions exist that could create fogging on the inside of the windshield.
NOTE: • It is not necessary to move the temperature settings. The system automatically adjusts the temperature, mode, and blower speed to provide comfort as quickly as possible. • The temperature can be displayed in U.S. or Metric units by selecting the US/M customer-programmable feature.
Operating Tips NOTE: Refer to the chart at the end of this section for suggested control settings for various weather condi- tions. Summer Operation The engine cooling system must be protected with a high-quality antifreeze coolant to provide proper corro- sion protection and to protect against engine overheating.
NOTE: • Recir culate without A/C should not be used for long periods, as fogging may occur . • Automatic T emperature Controls (A TC) will automati- cally adjust the climate control settings to reduce or eliminate window fogging on the front windshield.
Operating T ips Chart 406 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
ST ARTING AND OPERA TING CONTENTS ! ST AR TING PROCEDURES ............... 4 1 1 ▫ Manual T ransmission — If Equipped ....... 4 1 1 ▫ Automatic T ransmission — If Equipped .... .412 ▫ Keyless Enter-N-Go™ ................. .412 ▫ Normal Starting .
▫ Six-Speed Automatic T ransmission (1.4L T urbo Engine Only — DDCT) ........ .424 ▫ Six-Speed Automatic T ransmission (2.0L And 2.4L Engine Only — 6F24) .............. .435 ! AUT OSTICK® ........................ .443 ▫ Operation ..........
▫ T ire Loading And T ir e Pressur e .......... .471 ! TIRES — GENERAL INFORMA TION ....... .476 ▫ T ire Pressure ....................... .476 ▫ T ire Inflation Pressures ................ .478 ▫ T ire Pressures For High Speed Operation . . .
▫ MMT In Gasoline .................... .503 ▫ Materials Added T o Fuel ............... .503 ▫ Fuel System Cautions .................. .503 ▫ Carbon Monoxide W arnings ............ .504 ! ADDING FUEL ....................... .505 ▫ Fuel Filler Cap (Gas Cap) .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. W ARNING! • When leaving the vehicle, always remove the Key Fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
• If the key will not turn and the steering wheel is locked, rotate the wheel in either direction to relieve pressur e on the locking mechanism and then turn the key . Automatic T ransmission — If Equipped The shift lever must be in the P ARK or NEUTRAL position before you can start the engine.
3. The system takes over and attempts to start the vehicle. If the vehicle fails to start, the starter will disengage automatically after 10 seconds. 4. If you wish to stop the cranking of the engine prior to the engine starting, push the button again.
ENGINE ST AR T/STOP Button Functions — W ith Driver ’ s Foot OFF The Brake Pedal (In P ARK Or NEUTRAL Position) The ENGINE ST ART/ST OP button operates similar to an ignition switch.
2. Cycle the ignition in the ST ART position and release it when the engine starts. 3. If the engine fails to start within ten seconds, cycle the ignition to the STOP (OFF/LOCK) position, wait five seconds to allow the starter to cool, then repeat the Extended Park Starting procedur e.
CAUTION! T o prevent damage to the starter , do not continuously crank the engine for more than 25 seconds at a time. W ait 60 seconds before trying again.
3. Pull the cord to the front of the vehicle and plug it into a grounded, three-wir e extension cord. 4. After the vehicle is running, reattach the cord to the V elcro strap and properly stow away behind the driver ’s side headlamp. NOTE: • The engine block heater cord is a factory installed option.
CAUTION! Never drive with your foot resting on the clutch pedal, or attempt to hold the vehicle on a hill with the clutch pedal partially engaged, as this will cause abnormal wear on the clutch. NOTE: During cold weather , you may experience in- creased effort in shifting until the transmission fluid warms up.
Manual T ransmission Shift Speeds in MPH (KM/H) All Engines Gear Selection 2 to 3 3 to 4 4 to 5 5 to 6 Accel. 24 (39) 34 (55) 47 (76) 56 (90) Cruise 19 (31) 27 (43) 37 (60) 41 (66) Downshifting Moving from a high gear down to a lower gear is recommended to pr eserve brakes when driving down steep hills.
CAUTION! (Continued) • When descending a hill, be very careful to down- shift one gear at a time to prevent overspeeding the engine which can cause engine damage, and/or clutch damage, even if the clutch pedal is pressed. If transfer case is in low range the vehicle speeds to cause engine and clutch damage are significantly lower .
Manual T ransmission Shift Speeds in MPH (KM/H) Gear Selection 6 to 5 5 to 4 4 to 3 3 to 2 2 to 1 Maximum Speed 80 (129) 70 (1 13) 50 (81) 30 (48) 15 (24) CAUTION! If you skip a gear while downshiftin.
NOTE: Y ou must press and hold the brake pedal while shifting out of P ARK. W ARNING! • It is dangerous to shift out of P ARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse.
W ARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
Brake/T ransmission Shift Interlock System This vehicle is equipped with a Brake T ransmission Shift Interlock System (BTSI) that holds the shift lever in P ARK unless the brakes are applied.
information). T oggling the shift lever rearwar d (+) or forward (-) while in the AutoStick® position (beside the DRIVE position) will manually select the transmission gear , and will display the current gear in the instrument cluster as 1, 2, 3, etc.
Gear Ranges DO NOT race the engine when shifting from P ARK or NEUTRAL into another gear range. NOTE: After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold.
W ARNING! (Continued) • It is dangerous to shift out of P ARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. Y ou could lose control of the vehicle and hit someone or something.
W ARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever .
• Look at the transmission gear position display and verify that it indicates the P ARK position. • W ith brake pedal released, verify that the shift lever will not move out of P ARK. REVERSE (R) This range is for moving the vehicle backward. Shift into REVERSE only after the vehicle has come to a complete stop.
DRIVE (D) This range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy . The transmission automatically upshifts through all forward gears. The DRIVE position provides optimum driving characteris- tics under all normal operating conditions.
• When stopped on an incline, always use the brakes to hold the vehicle in place. On steep inclines, Hill Start Assist (HSA) will temporarily hold the car in position when the brake pedal is r eleased. If the accelerator pedal is not applied after a short time, the car will roll back.
Instrument Cluster Messages Messages will be displayed in the instrument cluster to alert the driver when certain unusual conditions occur . These messages are described below . MESSAGE DESCRIPTION GEAR NOT A V AILABLE In AutoStick® mode, the gear selected by the driver is not available due to a fault condition.
MESSAGE DESCRIPTION SHIFT TO NEUTRAL – THEN D or R The transmission has shifted itself into NEUTRAL (due to a fault condition, or over- heat due to excessive idling when stopped in DRIVE with the brakes released), but the shift lever remains in gear .
MESSAGE DESCRIPTION TRANS. HOT STOP SAFEL Y SHIFT TO P The transmission driving clutch has overheated. Pull over , shift the transmission into P ARK, and allow the vehicle to cool until “TRANS. COOL READY TO DRIVE” is displayed. SER VICE TRANSMIS- SION A transmission fault has been detected.
In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing the following steps: 1. Stop the vehicle. 2. Shift the transmission into P ARK. 3. T urn the ignition switch to the OFF position. 4. W ait approximately 10 seconds.
Only shift from DRIVE to P ARK or REVERSE when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has P ARK, REVERSE, NEU- TRAL, DRIVE, and AutoStick® (+/-) shift positions.
the transmission locking mechanism may make it diffi- cult to move the shift lever out of P ARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. W ARNING! • Never use the P ARK position as a substitute for the parking brake.
W ARNING! (Continued) • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into P ARK, turn the engine OFF , and remove the Key Fob.
CAUTION! • Before moving the shift lever out of P ARK, you must turn the ignition switch from the LOCK/OFF position to the ON/RUN position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • DO NOT race the engine when shifting from P ARK or NEUTRAL into another gear range, as this can damage the drivetrain.
W ARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions.
If the transmission temperature exceeds normal operat- ing limits, the transmission controller will modify the transmission shift schedule and expand the range of torque converter clutch engagement. This is done to prevent transmission damage due to overheating.
6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. NOTE: Even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience.
NOTE: Engagement of the torque converter clutch is inhibited at very cold temperatures. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold. This is normal.
• For GT models, the transmission will remain in the selected gear even when maximum engine speed is reached. The transmission will upshift only when commanded by the driver . Engine overspeed protec- tion is provided by the engine controls. • The transmission will automatically downshift to first gear when coming to a stop.
DRIVING ON SLIPPER Y SURF ACES Acceleration Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the driving wheels to pull erratically to the right or left. This phenomenon occurs when there is a differ ence in the surface traction under the front (driving) wheels.
DRIVING THROUGH W A TER Driving through water more than a few inches/ centimeters deep will requir e extra caution to ensure safety and prevent damage to your vehicle. Flowing/Rising W ater W ARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off).
CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water .
P ARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave an automatic transmission in P ARK, or manual transmission in REVERSE or first gear . The parking brake lever is located in the center console.
wheels toward the curb on a downhill grade and away from the curb on an uphill grade. For vehicles equipped with an automatic transmission, apply the parking brake before placing the shift lever in P ARK, otherwise the load on the transmission locking mecha- nism may make it difficult to move the shift lever out of P ARK.
W ARNING! (Continued) • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury . Also be certain to leave the transmission in P ARK. Failure to do so may allow the vehicle to roll and cause damage or injury .
W ARNING! • Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnor- mally high brake temperatures, excessive lining wear , and possible brake damage. Y ou would not have your full braking capacity in an emergency .
If the “SER VICE POWER STEERING # OR # POWER STEERING ASSIST OFF - SER VICE SYSTEM” message and a steering wheel icon are displayed on the EVIC/DID screen, it indi- cates that the vehicle needs to be taken to the dealer for service. It is likely the vehicle has lost power steering assistance.
(ESC). These systems work together to enhance both vehicle stability and control in various driving condi- tions. Anti-Lock Brake System (ABS) The Anti-Lock Brake System (ABS) provides increased vehicle stability and brake performance under most braking conditions.
W ARNING! • The ABS contains sophisticated electronic equip- ment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capa- bility .
Anti-Lock Brake W arning Light The “Anti-Lock Brake W arning Light” moni- tors the ABS. The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds.
W ARNING! BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. BAS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
ERM can only reduce the chance of wheel lift occurring during severe or evasive driving maneuvers. It cannot prevent wheel lift due to other factors, such as road conditions, leaving the roadway , or striking objects or other vehicles.
W ARNING! • TSC cannot stop all trailers from swaying. Always use caution when towing a trailer and follow the tongue weight recommendations. Refer to ”V ehicle Loading” and “T railer T owing” in “Starting and Operating” for further information.
5. Engage park brake. 6. Start engine and wait for ESC OFF lamp to turn off. 7. Apply brake pedal. 8. T urn steering wheel 200 degrees counter clockwise, just over half a turn from center position.
W ARNING! There may be situations on minor hills with a loaded vehicle, or while pulling a trailer , when the system will not activate and slight rolling may occur . This could cause a collision with another vehicle or object. Always remember the driver is responsible for brak- ing the vehicle.
W ARNING! (Continued) • Failure to follow these warnings may cause the vehicle to roll down the incline and could collide with another vehicle, object or person, and cause serious or fatal injury . Always remember to use the parking brake while parking on a hill and that the driver is responsible for braking the vehicle.
W ARNING! Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESC cannot prevent accidents, in- cluding those resulting from excessive speed in turns, driving on very slippery surfaces, or hydro- planing.
W ARNING! • When in % Partial Off % mode, the TCS functionality of ESC, (except for the limited slip feature de- scribed in the TCS section), has been disabled and the % ESC Off Indicator Light % will be illuminated.
Y aw control, traction control, and trailer sway control. If the lamp remains solid under normal driving conditions, your vehicle should be serviced at an authorized dealer . The “ESC Activation/Malfunction Indicator Light” starts to flash as soon as the tires lose traction and the ESC system becomes active.
TIRE SAFETY INFORMA TION Tire Markings NOTE: • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • Eur opean — Metric tire sizing is based on European design standards.
• T emporary spar e tires are designed for temporary emergency use only . T emporary high pressure com- pact spare tires have the letter “T” or “S” molded into the sidewall preceding the size designation. Example: T145/80D18 103M. • High flotation tire sizing is based on U.
EXAMPLE: R = Construction code – # R # means radial construction, or – # D # means diagonal or bias construction 15, 16, 18 = Rim diameter in inches (in) Service Description: 95 = Load Index – A.
EXAMPLE: Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire: • XL = Extra load (or reinfor ced) tire, or • LL.
EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of T ransportation – This symbol certifies that the tire is in compliance with the U.S. Department of T ransportation tire safety standards and is appro.
Tire T erminology And Definitions T erm Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door . Cold T ire Inflation Pressure Cold tire inflation pressur e is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.
Tire Loading And Tire Pressure T ire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver ’s side B-Pillar or the rear edge of the driver’s side door .
T ire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2.
3. T ire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear , and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
4. The resulting figure equals the available amount of cargo and luggage load capacity . For example, if “XXX” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in .
5 ST ARTING AND OPERA TING 475 I n f o r m a t i o n P r o v i d e d b y :.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
W ARNING! (Continued) • Unequal tire pressures can cause steering prob- lems. Y ou could lose control of your vehicle. • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure.
Tire Inflation Pressures The proper cold tire inflation pressur e is listed on the driver’s side B-Pillar or rear edge of the driver’s side door . At least once a month: • Check and adjust tir e pressur e with a good quality pocket-type pressur e gauge.
inflation pressur e should be increased by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. T ire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressur e will be too low .
T ire Repair If your tire becomes damaged, it may be repaired if it meets the following criteria: • The tire has not been driven on when flat. • The damage is only on the tread section of your tire (sidewall damage is not repairable). • The puncture is no greater than ¼ # (6 mm).
Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. W ARNING! Do not use summer tires in snow/ice conditions.
While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit studded tires; therefor e, local laws should be checked before using these tire types.
equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern.
Full Size Spare — If Equipped The full size spare is for temporary emergency use only . This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not.
Tire Spinning When stuck in mud, sand, snow , or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping. Refer to “Freeing A Stuck V ehicle” in “What T o Do In Emergencies” for further information.
These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16” (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “Replacement T ires” in this section for further infor- mation.
Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressur es. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance when replacement is needed.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle.
• Install on Front T ires • Due to limited clearance, • For a 205/55R16 the 12 mm Diamond T ir e Chain with Ratchet T ensioning Device from tirechain.com is rec- ommended. • For a 225/45R17 either the Peerless Auto-T rac or Thule CG-9 snow chain is recommended.
CAUTION! (Continued) • Observe the traction device manufacturer ’ s instruc- tions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufac- turer ’ s if it is less than 30 mph (48 km/h).
TIRE PRESSURE MONITORING SYSTEM (TPMS) The T ir e Pressure Monitor System (TPMS) will warn the driver of a low tire pressur e based on the vehicle recom- mended cold placard pressur e. The tire pressure will vary with temperature by about 1 psi (7.0 kPa) for every 12°F (6.
also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased pres- sure. The TPMS will warn the driver of a low tire pressur e if the tire pressur e falls below the low-pressure warning limit for any reason, including low temperature effects, or natural pressur e loss through the tire.
CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
Under-inflation also r educes fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability . • The TPMS is not a substitute for proper tire mainte- nance, and it.
T ire Pressure Monitoring Low Pressure W arnings The T ir e Pressure Monitoring T elltale Light will illumi- nate in the instrument cluster , a # LOW TIRE PRESSURE # message and “Inflate T ire to XX.
4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. NOTE: Y our vehicle is equipped with a compact spare wheel and tire assembly . 1. The compact spare tire does not have a tire pressur e monitoring sensor . Therefore, the TPMS will not moni- tor the tire pressur e in the compact spare tire.
Premium System — If Equipped The TPMS uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure lev- els. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressur e readings to the receiver module.
graphic display to the vehicle’s recommended cold plac- ard pressur e value. The system will automatically up- date, the “Inflate T ire to XX” message will no longer be displayed, the graphic di.
NOTE: Y our vehicle is equipped with a compact spare wheel and tire assembly . 1. The compact spare tire does not have a tire pressur e monitoring sensor .
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
Light spark knock at low engine speeds is not harmful to your engine. However , continued heavy spark knock at high speeds can cause damage and immediate service is requir ed. Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.
CAUTION! (Continued) emissions to exceed the applicable standard, and/or cause the “Malfunction Indicator Light” to illumi- nate. Pump labels should clearly communicate if a fuel contains greater than 10% Ethanol.
MMT In Gasoline Methylcyclopentadienyl Manganese T ricarbonyl (MMT) is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT .
CAUTION! (Continued) • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate ser- vice.
W ARNING! (Continued) • Guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly . Until repaired, drive with all side windows fully open.
3. Remove the fuel filler cap and hang cap by tether on fill door to prevent damage to body side. NOTE: In certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door around the entire perimeter to break the ice buildup and re-open the door .
CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel filler cap. A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermar- ket cap can cause the “Malfunction Indicator Light (MIL)” to illuminate, due to fuel vapors escaping from the system.
• T ighten the gas cap about one-quarter turn until you hear one click. This is an indication that the cap is properly tightened. • If the gas cap is not tighten properly , the MIL will come on. Be sure the gas cap is tightened every time the vehicle is refueled.
Rim Size This is the rim size that is appropriate for the tire size listed. Inflation Pressure This is the cold tire inflation pressure for your vehicle for all loading conditions up to full GA WR.
CAUTION! Do not load your vehicle any heavier than the GVWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles.
.
T railer Sway Control The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.
T railer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
T railer T owing Weights (Maximum T railer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. 1.4L T urbo Engine T railer towing is not recommended. Engine/T ransmission Frontal Area Max.
T railer And T ongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer . This places 10% to 15% of the GTW on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely from side-to-side which will cause loss of con- trol of vehicle and trailer .
NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer -installed options, must be considered as part of the total load on your vehicle.
W ARNING! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be dif ficult for the driver to control.
W ARNING! (Continued) • T otal weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. GVWR 2. GTW 3. GA WR 4. T ongue weight rating for the trailer hitch uti- lized. T owing Requirements — T ires • Do not attempt to tow a trailer while using a compact spare tire.
T owing Requirements — T railer Brakes • Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer . This could cause inadequate braking and possible personal injury . • An electronically actuated trailer brake controller is requir ed when towing a trailer with electronically actuated brakes.
T owing Requirements — T railer Lights And Wiring Whenever you pull a trailer , regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety . The T railer T ow Package may include a four-pin and seven-pin wiring harness.
T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Manual T ransmission — If Equipped If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.
If you REGULARL Y tow a trailer for more than 45 minutes of continuous operation, then change the transmission fluid and filter as specified for severe usage (police, fleet, taxi, or frequent trailer towing). Refer to the # Maintenance Schedule # for the proper maintenance intervals.
RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.) T owing This V ehicle Behind Another V ehicle T owing Condition Wheels OFF the Ground Manual T ransmis- sion 1.
NOTE: V ehicles equipped with a manual transmission or a DDCT transmission (1.4L turbo engine) may be recr eationally towed (flat towed) at any legal highway speed, for any distance, if the transmission is in NEU- TRAL . For vehicles with DDCT transmission (1.
WHA T TO DO IN EMERGENCIES CONTENTS ! HAZARD W ARNING FLASHERS .......... .527 ! IF YOUR ENGINE OVERHEA TS ........... .527 ! WHEEL AND TIRE TORQUE SPECIFICA TIONS ..................... .528 ▫ T orque Specifications ................. .528 ! TIRE SER VICE KIT — IF EQUIPPED .
! SHIFT LEVER OVERRIDE ............... .556 ! T OWING A DISABLED VEHICLE .......... .559 ▫ 2.0L / 2.4L Automatic T ransmission ........ .560 ▫ Manual T ransmission Or 1.
HAZARD W ARNING FLASHERS The Hazard W arning flasher switch is located in the center of the instrument panel. Press the switch to turn on the Hazard W arning flashers. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency .
CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H,” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H,” turn the engine off immediately and call for service.
T ighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.
W ARNING! T o avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury . TIRE SERVICE KIT — IF EQUIPPED Small punctures up to ¼ ” (6 mm) in the tire tread can be sealed with T ir e Service Kit.
Using The Mode Select Knob And Hoses Y our T ir e Service Kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Push in the Mode Select Knob (5) and turn to this position for air pump operation only . Use the Black Air Pump Hose (7) when selecting this mode.
• The Sealant Bottle (1) and Sealant Hose (6) are a one tire application use and need to be replaced after each use. Always replace these components immediately at your original equipment vehicle dealer .
W ARNING! • Do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the T ire Service Kit.
W ARNING! (Continued) • T ire Service Kit Sealant solution contains latex. In case of an allergic reaction or rash, consult a phy- sician immediately . Keep T ire Service Kit out of reach of children. If swallowed, rinse mouth imme- diately with plenty of water and drink plenty of water .
4. Remove the cap from the valve stem and then screw the fitting at the end of the Sealant Hose (6) onto the valve stem. 5. Uncoil the Power Plug (8) and insert the plug into the vehicle’s 12 V olt power outlet. NOTE: Do not remove foreign objects (e.
NOTE: If the Mode Select Knob (5) is on Air Mode and the pump is operating, air will dispense from the Air Pump Hose (7) only , not the Sealant Hose (6). If the sealant (white fluid) does flow through the Sealant Hose (6): 1. Continue to operate the pump until sealant is no longer flowing through hose (typically takes 30 - 70 seconds).
hose, and place the T ire Service Kit in the vehicle storage location. Quickly proceed to (D) “Drive V ehicle.” CAUTION! • The metal end fitting from Power Plug (8) may get hot after use, so it should be handled carefully .
3. Uncoil the Air Pump Hose (7) (black in color) and screw the fitting at the end of hose (7) onto the valve stem. 4. Check the pressur e in the tire by reading the Pressure Gauge (3). If tire pressure is less than 19 psi (1.3 Bar): The tire is too badly damaged.
(F) Sealant Bottle And Hose Replacement: 1. Uncoil the Sealant Hose (6) (clear in color). 2. Locate the round Sealant Bottle release button in the recessed area under the sealant bottle. 3. Pr ess the Sealant Bottle release button. The Sealant Bottle (1) will pop up.
W ARNING! (Continued) • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.
3. Remove the fastener securing the jack and spare tire. 4. Remove the scissors jack and wheel bolt wrench from the spare wheel as an assembly . T urn the jack screw to the left to loosen the wheel bolt wrench, and remove the wrench from the jack assembly .
W ARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately .
Jacking And Changing A Tire W ARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.
CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. Remove the spare tire, jack, and wheel bolt wrench. NOTE: The jack handle attaches to the side of the jack with two attachment points.
2. If equipped with aluminum wheels where the center cap covers the wheel bolts, use the wheel bolt wrench to pry the center cap off carefully before raising the vehicle. 3. Befor e raising the vehicle, use the wheel bolt wrench to loosen, but not remove, the wheel bolts on the wheel with the flat tire.
5. Raise the vehicle just enough to remove the flat tire and install the spare tire. W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire.
NOTE: • For vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare. • Refer to “Compact Spare T ir e” and to “Limited-Use Spare” under “T ir es .
9. Lower the vehicle to the ground by turning the jack handle counterclockwise. 10. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for increased leverage. T ighten the wheel bolts in a star pattern until each wheel bolt has been tightened twice.
3. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand, snapping the cover over the two wheel bolts. Do not use a hammer or excessive force to install the cover . 4. Install the remaining wheel bolts with the threaded end of the wheel bolt toward the wheel.
“T or que Specifications” in this section for proper lug bolt torque. If in doubt about the corr ect tightness, have them checked with a torque wr ench by your authorized dealer or service station. 7. Lower the jack until it is free. Remove the wheel blocks.
5. Lower the jack until it is free. Remove the wheel blocks. Reassemble the lug wrench to the jack assem- bly and stow it in the spare tire area. Secure the assembly using the means provided.
W ARNING! • T ake care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is ON. Y ou can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.
3. If using another vehicle to jump-start the battery , park the vehicle within the jumper cables r each, set the parking brake and make sure the ignition is OFF . W ARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.
W ARNING! Do not connect the jumper cable to the negative (-) post of the discharged battery . The resulting electri- cal spark could cause the battery to explode and could result in personal injury . Only use the specific ground point, do not use any other exposed metal parts.
CAUTION! Accessories plugged into the vehicle power outlets draw power from the vehicle’ s battery , even when not in use (i.e., cellular phones, etc.). Eventually , if plugged in long enough without engine operation, the vehicle’ s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.
NOTE: Pr ess the # ESC Off # switch, to place the Electronic Stability Control (ESC) system in “partial off” mode, before rocking the vehicle. Refer to “Electronic Brake Control” in “Starting And Operating” for further infor- mation. Once the vehicle has been freed, press the # ESC Off # switch again to restor e # ESC On # mode.
3. Remove the rubber storage tray liner from the center console, then lift up the front of the shift lever bezel, carefully disengage the bezel from the shift lever housing, and slide it up to the top of the shift lever . 4. Pr ess and maintain firm pressur e on the brake pedal.
6. Move the shift lever to the NEUTRAL position. 7. The vehicle may then be started in NEUTRAL. 8. Reinstall the shift lever bezel (use car e to avoid pinching the wiring), and the rubber storage tray liner .
TOWING A DISABLED VEHICLE NOTE: This section describes procedures for towing a disabled vehicle using a commercial towing service. T owing Condition Wheels OFF The Ground 2.
CAUTION! • DO NOT use sling-type equipment when towing. V ehicle damage may occur . • When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. • The manufacturer does not recommend towing this vehicle using a tow dolly .
If the key fob is unavailable, or the vehicle’s battery is discharged, refer to “Shift Lever Override” in this section for instructions on shifting the automatic transmission out of P ARK for loading onto a flatbed truck. Manual T ransmission Or 1.
I n f o r m a t i o n P r o v i d e d b y :.
MAINT AINING YOUR VEHICLE CONTENTS ! ENGINE COMP AR TMENT — 1.4L TURBO . . . .565 ! ENGINE COMP AR TMENT — 2.0L ......... .566 ! ENGINE COMP AR TMENT — 2.4L ......... .567 ! ONBOARD DIAGNOSTIC SYSTEM — OBD II . .568 ▫ Loose Fuel Filler Cap Message .
▫ Exhaust System ..................... .582 ▫ Cooling System ..................... .585 ▫ Brake System ....................... .591 ▫ Automatic T ransmission — If Equipped .... .593 ▫ Manual T ransmission — If Equipped ...... .595 ▫ Appearance Care And Protection From Corrosion .
ENGINE COMP ARTMENT — 1.4L TURBO 1 — Engine Coolant Reservoir 5 — Power Distribution Center (Fuses) 2 — Engine Oil Level Indicator 6 — W asher Fluid Reservoir 3 — Engine Oil Fill 7 — Bat.
ENGINE COMP ARTMENT — 2.0L 1 — Engine Coolant Reservoir 5 — W asher Fluid Reservoir 2 — Engine Oil Fill 6 — Battery 3 — Brake Fluid Reservoir 7 — Engine Oil Level Indicator 4 — Power D.
ENGINE COMP ARTMENT — 2.4L 1 — Engine Coolant Reservoir 5 — W asher Fluid Reservoir 2 — Engine Oil Fill 6 — Battery 3 — Brake Fluid Reservoir 7 — Engine Oil Level Indicator 4 — Power D.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row , the system will turn on the MIL.
3. Appr oximately 15 seconds later , one of two things will happen: • The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
DEALER SERVICE Y our authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner . Service Manuals are available which include detailed service information for your vehicle.
CAUTION! (Continued) • Y our vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering or air conditioning.
CAUTION! (Continued) pressure and an increase in oil temperature. This could damage your engine. Also, be sure the oil fill cap is replaced and tightened after adding oil. Change Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.
Lubricants which do not have both the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used. Engine Oil V iscosity (SAE Grade) — 2.0L And 2.4L Engine MOP AR® SAE 0W -20 engine oil or equivalent Pennzoil® or Shell Helix® is recommended for all operating tem- peratures.
Engine Oil Filter The engine oil filter should be replaced with a new filter at every engine oil change. Engine Oil Filter Selection This manufacturer’s engines have a full-flow type oil filter . Use a filter of this type for replacement. The quality of r eplacement filters varies considerably .
Tires Checking For T ire W ear Once a month, check the tire inflation pressur es and look for unusual wear or damage. Rotate at the first sign of irregular wear , even if it occurs before the oil indicator system turns on. Maintenance-Free Battery Y our vehicle is equipped with a maintenance-free battery .
W ARNING! (Continued) • The battery in this vehicle has a vent hose that should not be disconnected and should only be replaced with a battery of the same type (vented).
CAUTION! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the New V ehicle Limited W arranty .
2. Disengage the retaining tab that secures the filter cover to the HV AC housing, and remove the cover . 3. Remove the A/C air filter by pulling it straight out of the housing.
4. Install the A/C air filter with the air filter position indicators pointing in the same direction as removal. When installing the filter cover , make sure the retain- ing tab fully engages the cover . CAUTION! The A/C air filter is identified with an arrow to indicate airflow direction through the filter .
the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function.
When refilling the washer fluid reservoir , take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. T o prevent freeze-up of your windshield washer system in cold weather , select a solution or mixture that meets or exceeds the temperature range of your climate.
W ARNING! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. T o avoid breathing CO, refer to “Safety T ips/Exhaust Gas” in “Things T o Know Before Starting Y our V ehicle” for further information.
Under normal operating conditions, the catalytic con- verter will not requir e maintenance. However , it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position.
If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with OA T coolant (antifreeze) (conforming to MS-12106).
CAUTION! (Continued) • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator .
(antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated.
W ARNING! • Do not open hot engine cooling system. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. T o prevent scalding or injury , do not remove the pressure cap while the system is hot or under pressure.
Points T o Remember NOTE: When the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment.
Brake System In order to assure brake system performance, all brake system components should be inspected periodically . Refer to the “Maintenance Schedule” for the proper maintenance intervals. W ARNING! Riding the brakes can lead to brake failure and possibly a collision.
Use only manufacturer’s recommended brake fluid. Re- fer to “Fluids, Lubricants, and Genuine Parts” in “Main- taining Y our V ehicle” for further information. W ARNING! • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Y our V ehicle” for further information.
W ARNING! (Continued) • Do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. CAUTION! Use of improper brake fluids will affect overall clutch system performance.
Special Additives The manufacturer str ongly recommends against using any special additives in the transmission. Automatic T ransmission Fluid (A TF) is an engineered product and its performance may be impaired by supple- mental additives. Therefor e, do not add any fluid addi- tives to the transmission.
Fluid and Filter Changes Under normal operating conditions, the fluid installed at the factory will provide satisfactory lubrication for the life of the vehicle. However , if the vehicle is used for frequent trailer towing, police, fleet, taxi, etc., change the fluid as indicated in the Maintenance Schedule.
passable in snow and ice, and chemicals that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.
.
• For grease stains, apply MOP AR® Multi-Purpose Cleaner or equivalent to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue. • Do not use any harsh solvents or any other form of protectants on Stain Repel products.
Cleaning Headlights Y our vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefor e differ ent lens cleaning procedures must be followed.
Instrument Panel Bezels CAUTION! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully . Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface.
W ARNING! (Continued) not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor , torn web- bing, etc.). FUSES W ARNING! • When replacing a blown fuse, always use an appro- priate replacement fuse with the same amp rating as the original fuse.
Cavity Cartridge Fuse Mini Fuse Description F1 – 20 Amp Y ellow Front Heated Seats – If Equipped F2 – 20 Amp Y ellow Rear Heated Seats, Heated Steering Wheel – If Equipped F3 – 10 Amp Red Pa.
Cavity Cartridge Fuse Mini Fuse Description F24 – 5 Amp T an Run/Accessory Relay F25 – 5 Amp T an T ransmission Control Module #4 F26 – 5 Amp T an Stop Lamp Switch F27 – 10 Amp Red Pneumatic Lumbar Support Underhood Fuses The Power Distribution Center is located on the right side of the engine compartment, behind the battery .
Cavity Maxi Fuse Mini Fuse Description F01 70 Amp T an – Body Control Module #1 F02 60 Amp Blue – Body Control Module #2 F03 30 Amp Green – Output For Starter Relay #1 F04 40 Amp Orange – ESC .
Cavity Maxi Fuse Mini Fuse Description F19 – 10 Amp Red A/C Compressor Clutch F20 – 30 Amp Green Rear Defroster (EBL) F21 – 20 Amp Y ellow Fuel Pump F22 – 10 Amp Red Occupant Restraint Control.
Cavity Maxi Fuse Mini Fuse Description F87 – 10 Amp Red W astegate, Purge Solenoid, OBD V ent V alve, Oxygen Sensor Heaters F88 – 10 Amp Red Heated Outside Mirrors Body Control Module (BCM) Fuses .
Cavity Cartridge Fuse Mini Fuse Description F42 – – Spare F43 – 20 Amp Y ellow W indshield W asher Pump F47 – 5 Amp T an T ransmission Control Module (T cm) F48 – 20 Amp Y ellow Spare F49 – 7.5 Amp Brown Stop Lamp Switch F50 – 7.5 Amp Brown Pneumatic Lumbar Support F51 – 7.
VEHICLE STORAGE If you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery . • Disconnect the negative cable from the battery . • Anytime you store your vehicle, or keep it out of service (i.e.
Exterior Bulbs Bulb Number Low Beam/High Beam (Bi-Halogen Headlamp) HIR2 Low Beam/High Beam (Bi-Xenon Headlamp) D3S ** Front Park/T urn Signal Lamp 7442NALL Sidemarker Lamp 194 Front Fog Lamp H1 1 Cen.
BULB REPLACEMENT NOTE: Lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor . T urning the lamps on will usually accelerate the clearing process.
.
5. T wist the bulb socket one quarter turn clockwise to install. 6. Install trim cover . License Lamp 1. Remove the screws securing the lamp to the rear fascia. 2. Remove the bulb and socket assembly . 3. Disconnect the bulb from the socket assembly and install the replacement bulb.
4. Reinstall the bulb and socket assembly . 5. Reattach the lamp to the rear fascia, and then install the screws. 1—L i c e n s eL a m pB u l b 2—S o c k e t 614 MAINT AINING YOUR VEHICLE I n f o .
FLUID CAP ACITIES U.S. Metric Fuel (Approximate) Fuel (1.4L Engines) 13.2 Gallons 50 Liters Fuel (2.0L/2.4L Engines) 14.2 Gallons 54 Liters Fuel (2.4L GT models only) 15.8 Gallons 60 Liters Engine Oil W ith Filter 1.4L T urbo Engine (SAE 5W -40 Synthetic, API Certified) 4 Quarts 3.
FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant W e recommend you use MOP AR® Antifreeze/Coolant 10 Y ear/150,000 Mile Formula OA T (Organic Additive T echnology) or equivalent meeting the requir ements of Chrysler Material Standard MS-12106.
Component Fluid, Lubricant, or Genuine Part Engine Oil Filter W e recommend you use MOP AR® Engine Oil Filter or equivalent. Spark Plugs W e recommend you use MOP AR® Spark Plugs. Fuel Selection – 1.4L T urbo Engine 91 Octane Recommended – 87 Octane Acceptable.
CAUTION! • Mixing of engine coolant (antifreeze) other than specified Organic Additive T echnology (OA T) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.
Chassis Component Fluid, Lubricant, or Genuine Part Automatic T ransmission (1.4L T urbo Engine) – If Equipped Gear Oil : Use only MOP AR® C Series Manual & Dual Dry Clutch T rans- mission Fluid or equivalent. Control system : Use only MOP AR® C Series DDCT SAE 75W Hydraulic Fluid or equivalent.
I n f o r m a t i o n P r o v i d e d b y :.
MAINTENANCE SCHEDULES CONTENTS ! MAINTENANCE SCHEDULE ............ .622 ▫ Required Maintenance ................. .623 8 M A I N T E N A N C E S C H E D U L E S I n f o r m a t i o n P r o v i d e d .
MAINTENANCE SCHEDULE Y our vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate.
Check the tire inflation pressures and look for unusual wear or damage. Check the fluid levels of the coolant reservoir , and brake master cylinder as needed. Check function of all interior and exterior lights. Required Maintenance Refer to the Maintenance Schedules on the following pages for requir ed maintenance.
Maintenance Chart Mileage Or Time Passed (Whichever Comes First) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 Or Y ears: 2 3 4 5 6 7 8 9 10 .
Mileage Or Time Passed (Whichever Comes First) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 Or Y ears: 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 Or Kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 Replace the spark plugs (2.
Mileage Or Time Passed (Whichever Comes First) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 Or Y ears: 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 Or.
W ARNING! • Y ou can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
I n f o r m a t i o n P r o v i d e d b y :.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS ! SUGGESTIONS FOR OBT AINING SER VICE FOR YOUR VEHICLE ...................... .631 ▫ Pr epare For The Appointment ............ .631 ▫ Pr epare A List ....................... .631 ▫ Be Reasonable W ith Requests .
! DEP ARTMENT OF TRANSPOR T A TION UNIFORM TIRE QUALITY GRADES ................ .637 ▫ T readwear .......................... .637 ▫ T raction Grades .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you are having warranty work done, be sure to have the right papers with you. T ake your warranty folder . All work to be performed may not be cover ed by the warranty .
facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner . This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process.
In Mexico Contact: A v . Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P . 05109 Mexico, D. F . In Mexico City: 5081-7568 Outside Mexico City: 1-800-505-1300 Customer Assistance For The Hearing Or.
The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract.
MOP AR® P ARTS MOP AR® fluids, lubricants, parts, and accessories are available from an authorized dealer . They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. REPORTING SAFETY DEFECTS In The 50 United States And Washington, D.
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Call toll free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orldwide W eb at: • www .techauthority .com DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway T raffic Safety Administration.
.
INDEX 10 I n f o r m a t i o n P r o v i d e d b y :.
About Y our Brakes ....................... .450 ABS (Anti-Lock Brake System) ............... .453 Adding Engine Coolant (Antifreeze) ........... .587 Adding Fuel ............................ .505 Adding W asher Fluid ..................... .581 Additives, Fuel .
T amper Alert ........................... 2 2 V ehicle Security Alarm .................... 2 0 Alarm Light ............................ .315 Alarm, Panic ............................. 2 2 Alarm (Security Alarm) ...................... 2 0 Alarm System (Security Alarm) .
Connect Or Disconnect Link Between the Uconnect® Phone And Mobile Phone ........ .192 Pair (Link) Uconnect® Phone T o A Mobile Phone .............................. .172 Body Mechanism Lubrication ................ .580 B-Pillar Location .............
Checks, Safety ............................ 1 1 0 Child Restraint ............................ 8 8 Child Restraints Booster Seats ........................... 9 2 Child Restraints ......................... 8 8 Child Seat Installation ..................
Points to Remember .................... .590 Pressur e Cap ......................... .588 Radiator Cap ......................... .588 Selection of Coolant (Antifreeze) ............ .586 Corrosion Protection ...................... .595 Cruise Light ...
Electrical Power Outlets .................... .287 Electric Rear W indow Defrost ................ .298 Electric Remote Mirrors .................... .124 Electronic Brake Control System .............. .452 Brake Assist System .................... .455 Electronic Stability Program .
Entry System, Illuminated .................... 2 3 Ethanol ............................... .501 Event Data Recorder ........................ 8 7 Exhaust Gas Caution ....................... 1 1 1 Exhaust System ........................... 1 1 1 Exterior Folding Mirrors .
Filler Cap (Gas Cap) .................... .505 Filler Door (Gas Cap) ................... .315 Gasoline ............................. .500 Gauge .............................. .314 Light ............................... .316 Materials Added ............
Headlights Automatic ........................... .237 Cleaning ............................ .600 Delay ............................... .238 High Beam/Low Beam Select Switch ........ .243 Lights On Reminder .................... .240 On W ith W ipers ..
iPod®/USB/MP3 Control Bluetooth® Streaming Audio .............. .175 Jacking Instructions ....................... .543 Jack Location ........................... .540 Jack Operation .......................... .539 Jump Starting ......................
Lane Change Assist ....................... .243 Lap/Shoulder Belts ......................... 5 2 Latches ................................ 1 1 4 Lead Free Gasoline ....................... .500 Leaks, Fluid ............................. 1 1 4 Life of T ires .
Passing ............................. .243 Reading ............................. .243 Seat Belt Reminder ..................... .312 Security Alarm ........................ .315 Service ............................... 6 1 1 Service Engine Soon (Malfunction Indicator) .
Automatic Dimming .................... .122 Electric Powered ....................... .124 Electric Remote ........................ .124 Exterior Folding ....................... .123 Heated .............................. .124 Outside ..................
Overheating, Engine ...................... .310 Owner’s Manual (Operator Manual) ............. 4 Paint Care ............................. .595 Panic Alarm .............................. 2 2 Parking Brake ........................... .448 Parking On Hill .
Recorder , Event Data ....................... 8 7 Recreational T owing ...................... .523 Reformulated Gasoline .................... .501 Refrigerant ............................. .578 Reminder , Lights On ...................... .240 Reminder , Seat Belt .
Safety Checks Inside V ehicle .................. 1 1 2 Safety Checks Outside V ehicle ................ 1 1 4 Safety Defects, Reporting ................... .635 Safety , Exhaust Gas ........................ 1 1 1 Safety Information, T ire .............
Security Alarm Arm The System ........................ 2 0 Rearming The System ..................... 2 0 Security Alarm .......................... 2 0 T amper Alert ........................... 2 2 Selection of Oil .......................... .573 SENTR Y KEY® FCC General Information .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Dodge Dart (2015) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Dodge Dart (2015) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Dodge Dart (2015), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Dodge Dart (2015) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Dodge Dart (2015), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Dodge Dart (2015).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Dodge Dart (2015). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Dodge Dart (2015) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
