Manuel d'utilisation / d'entretien du produit 2009 Ram Chassis Cab du fabricant Dodge
Aller à la page of 429
2009 RAM TRUCK CHASSIS CAB RAM TR UCK CHASSIS C AB Chrysler LL C 81-326-0926 First Edition Printed in U.S.A. OWNER ’S MANU AL 2009.
VEHICLES SOLD IN CANADA W ith respect to any V ehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor . DRIVING AND ALCOHOL Drunken driving is one of the most fr equent causes of accidents.
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION .............................................................3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ............................... 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 6 䡵 V an Conversions/Campers ................. 6 䡵 V ehicle Identification Number .
INTRODUCTION This Owner’s Manual has been prepar ed with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a W arranty Information Booklet and various customer-oriented documents.
INTRODUCTION 5 1.
W ARNINGS AND CAUTIONS This Owner’s Manual contains W ARNINGS against op- erating procedur es that could result in an accident or bodily injury . It also contains CAUTIONS against proce- dures that could r esult in damage to your vehicle. If you do not read this entir e manual, you may miss important information.
VEHICLE IDENTIFICA TION NUMBER The V ehicle Identification Number (VIN) is found on the left front corner of the instr ument panel, visible through the windshield. This number also appears on the Auto- mobile Information Disclosure Label af fixed to a window on your vehicle, the vehicle registration and title.
.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys ................. 1 2 ▫ Ignition Key Removal .................. 1 2 ▫ Locking Doors W ith The Key ............. 1 4 䡵 Steering Wheel Lock — If Equipped .......
▫ T o Lock The Doors .................... 2 2 ▫ Using The Panic Alarm ................. 2 3 ▫ Programming Additional RKE T ransmitters . . . 24 ▫ General Information ................... 2 4 ▫ RKE T ransmitter Battery Service ........... 2 5 䡵 Remote Starting System — If Equipped .
▫ Driver And Right Front Passenger Supplemental Restraint System (SRS) – Airbag ............................. 4 8 ▫ Event Data Recorder (EDR) .............. 5 7 ▫ Child Restraint ....................... 6 0 䡵 New Engine Break-In ............
A WORD ABOUT YOUR KEYS The authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys fr om your authorized dealer . Ask your authorized dealer for these numbers and keep them in a safe place.
NOTE: • If you try to remove the key befor e you place the shift lever in P ARK, the key may become trapped tempo- rarily in the ignition cylinder . If this occurs, rotate the key to the right slightly , then remove the key as described.
W ARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seri- ously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle.
T o Release the Steering Wheel Lock Insert the key in the ignition switch and start the engine. If the key is difficult to turn, move the wheel slightly to the right or left to disengage the lock. NOTE: If you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it.
During normal operation, after turning on the ignition switch, the V ehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a pr oblem with the electronics.
CAUTION! Always remove the Sentry Keys 威 from the vehicle and lock all doors when leaving the vehicle unat- tended. At the time of purchase, the original owner is pr ovided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location.
4. Insert a blank Sentry Key 威 into the ignition switch. T urn the ignition switch to the ON position within 60 seconds. After 10 seconds, a single chime will sound.
VEHICLE SECURITY ALARM SYSTEM — IF EQUIPPED This V ehicle Security Alarm system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visible signals. For the first three minutes the horn will sound and the headlights and security light will flash repeatedly .
T o Disarm the System Use the RKE transmitter to unlock the door . If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the V ehicle Security Light will flash for 30 seconds. Check the vehicle for tampering.
REMOTE KEYLESS ENTR Y (RKE) — IF EQUIPPED The system allows you to lock or unlock the doors from distances up to about 23 ft (7 m) using a Remote Keyless Entry (RKE) transmitter . The RKE transmitter does not need to be pointed at the vehicle to activate the system.
T o Unlock the Doors Press and r elease the UNLOCK button on the RKE transmitter once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and, if installed, the cargo lamp will turn on for 30 seconds.
The Horn Chirp feature is activated when shipped fr om the assembly plant. If desired, this featur e can be disabled by using the following procedur e: 1. Perform this operation while standing outside the vehicle. 2. Press and hold the LOCK button on a pr ogrammed (i.
T o cancel the Panic Mode, press and r elease the P ANIC button on the transmitter a second time, after five sec- onds. Panic Mode will automatically cancel after three minutes, or if the vehicle is started and exceeds 15 mph (24 km/h). During the Panic Mode, the door locks and RKE systems will function normally .
RKE T ransmitter Battery Service 1. W ith RKE transmitter buttons facing down, use a flat blade or dime to pry the two halves of the RKE transmit- ter apart. Make sure not to damage the r ubber gasket during removal. 2. Remove and replace the battery .
REMOTE ST ARTING SYSTEM — IF EQUIPPED Y our vehicle may be equipped with a remote starting system, which will allow the vehicle to be started from distances up to approximately 300 ft (91 m) away fr om the vehicle using the Remote Keyless Entry (RKE) trans- mitter , which is part of your ignition key .
The vehicle can be started remotely up to a maximum of two times. The vehicle is also allowed a maximum of one failed start, where the r emote start sequence was initiated but the engine stopped cranking without starting.
Power Door Locks — If Equipped A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate.
3. Place the key into the ignition. 4. W ithin 15 seconds, cycle the key from the LOCK position to the ON/RUN position a minimum of four times, ending in the LOCK position. (Do not start the engine.) 5. W ithin 30 seconds, press the driver’s door LOCK switch in the LOCK direction.
5. W ithin 30 seconds, press the driver’s door LOCK switch in the UNLOCK direction. 6. A single chime will sound to indicate the feature has been changed. 7. Repeat the above steps to alternate the availability of this feature. 8. If a chime is not heard, the pr ogram mode was canceled before the featur e could be changed.
T o use the system, open each rear door , slide the lever UP to engage the locks and DOWN to disengage the child protection door locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even, if the inside door LOCK is in the UNLOCKED position.
WINDOWS Power Windows – If Equipped The control on the left fr ont door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window contr ol and on the rear doors of Quad Cab 威 models.
Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, r elease, and the window will go down automatically . W indow Lockout Switch (4-Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors.
Power Sliding Rear Window – If Equipped The power sliding rear window switch is located on the instrument panel below the climate contr ols. Press the right side of the switch to open the glass and the left side of the switch to close the glass.
OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle are the r estraint systems. These include the front and rear seat belts for the driver and all passengers, and front airbags for both the driver and fr ont passenger .
of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions except the Quad Cab 威 front center seating position have combination lap/shoulder belts.
W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision best. W earing your belt in the wrong place could make your injuries in a collision much worse.
2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
W ARNING! • A belt buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal inju- ries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system.
2. T o reattach the seat belt to the fr ont center seat, pull the black buckle latch plate forward fr om the cab back panel and insert it into the black keyed buckle until there is an audible “click”. For proper seatbelt usage, r efer “Lap/ Shoulder Belt Operating Instructions” in this section.
W ARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted.
Adjustable Upper Shoulder Belt Anchorage In the front r ow outboard seats, the shoulder belt can be adjusted upward or downwar d to help position the belt away from your neck. Pr ess the button located on the upper belt guide, and then move it up or down to the position that fits you best.
How T o Use The Automatic Locking Mode 1. Buckle the combination lap/shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Enhanced Driver Seat Belt Reminder System (BeltAlert 姞 ) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced W arning System (BeltAlert 威 ) will alert the driver to buckle their seat belt.
4. T urn off the engine. A single chime will sound to signify that you have successfully completed the programming. The Enhanced W arning System (BeltAlert 威 ) can be reac- tivated by repeating this pr ocedure.
Driver And Right Front Passenger Supplemental Restraint System (SRS) – Airbag This vehicle may have front airbags for both the driver and front passenger (if equipped) as a supplement to the seat belt restraint systems. The driver’s fr ont airbag is mounted in the center of the steering wheel.
W ARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflat- ing.
• Infants in rear -facing child restraints must NEVER ride in the front seat of a vehicle with a passenger fr ont airbag unless the airbag is turned off (Regular Cab V ehicles Only). An airbag deployment can cause se- vere injury or death to infants in that position.
Airbag System Components The airbag system consists of the following: • Occupant Restraint Controller (ORC) • AIRBAG Readiness Light • Driver Airbag • Passenger Airbag (if equipped) • Steeri.
• If it detects a malfunction in any part of the system, it turns on the light either momen- tarily or continuously . The instrument clus- ter will flash the seat belt indicator if it detects a fault with the airbag indicator .
Passenger Airbag On/Off Switch (Regular Cab V ehicles Only) – If Equipped The passenger front airbag is to be turned of f only if the passenger: • is an infant (less than one year old) who must ri.
W ARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash.
If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and fr ont passenger as the airbags deploy and unfold.
Enhanced Accident Response System If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically . In addition, approximately 10 seconds after the vehicle has stopped moving, the interior lights will light until the ignition switch is turned off.
NOTE: Perchlorate Material – special handling may apply: Refer to www .dtsc.ca.gov/hazardouswaste/per chlorate. Airbag W arning Light Y ou will want to have the airbags ready to inflate for your protection in an impact.
NOTE: • A near-deployment event occurs when the airbag sensor detects severe vehicle deceleration usually in- dicative of a crash, but not severe enough to warrant airbag deployment. • Under certain circumstances, EDR data may not be recor ded (e.
1. Used for resear ch purposes, such as to match data with a particular crash recor d in an aggregate database, provided confidentiality of personal data is ther eafter preserved 2. Used in defense of litigation involving a Chrysler LLC product 3. Requested by police under a legal warrant 4.
Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces r equire that small children ride in pr oper restraint systems. This is the law , and you can be prosecuted for ignoring it.
of child restraints can be used r earward-facing: infant carriers and ⬙ convertible ⬙ child seats. Both types of child restraints ar e held in the vehicle by the lap/ shoulder belt. • The infant carrier is only used rearwar d-facing in the vehicle.
W ARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint.
Allow the belt to return to the r etractor , pulling on the excess webbing to tighten the lap portion about the child restraint. Refer to ⬙ Automatic Locking Retractors (ALR) Mode ⬙ in this section.
Lower Anchors and T ether for CHildren (LA TCH) Each vehicle is equipped with the child restraint anchor - age system called LA TCH, which stands for Lower Anchors and T ether for CHildren. LA TCH child restraint anchorage systems are installed in the Regular Cab passenger seat position and the Quad Cab 威 rear seat outboard positions.
Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seat back tether anchorage have been available for some time.
NOTE: When using the LA TCH attaching system to install a child restraint, please ensur e that all seat belts not being used for occupant restraints ar e stowed and out of reach of childr en. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach.
rearwar d-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the tension in the strap. In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages.
W ARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
Multiple Child Restraint Installation Sequence (Quad Cab 威 - Rear Seats) 1. Obtain tether straps by raising the head restraints and reaching between the r ear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly impr oved by raising the seat cushion to the “up” position.
5. Place a child restraint on the center r ear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor dir ectly behind the seat and to the anchor directly behind the right seat.
T ether Anchorage Points at All Three Seating Positions 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor dir ectly behind the seat. 2. Lift the cover , and attach the hook to the square opening in the sheet metal.
Children T oo Large for Booster Seats Children who ar e large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat.
occur . For recommended viscosity and quality grades, refer to “Engine Oil” under “Maintenance Pr ocedures” in Section 7. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. A new engine may consume some oil during its first few thousand miles (kilometers) of operation.
• The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Be aware of changes in the sound of the exhaust system, exhaust fumes detected inside the vehicle, or damage to the underside or rear of the vehicle.
Airbag W arning Light The airbag warning light should come on, and remain on, for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer . If the light stays on, flickers or comes on while driving, have the system checked by an authorized dealer .
.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors .............................. 8 1 ▫ Inside Day/Night Mirror ................ 8 1 ▫ Automatic Dimming Mirror — If Equipped . . . 82 ▫ Outside Mirrors ...................... 8 2 ▫ Outside Mirrors Folding Featur e .
䡵 Seats .............................. 1 1 4 ▫ 40-20-40 Front Seat ................... 1 1 5 ▫ Reclining Seats ...................... 1 1 6 ▫ Adjustable Head Restraints ............. 1 1 7 ▫ Manual Rotary Lumbar Support Adjustment — If Equipped .
䡵 Electronic Speed Contr ol — If Equipped ..... 1 3 3 ▫ T o Activate ......................... 1 3 4 ▫ T o Set At A Desir ed Speed .............. 1 3 4 ▫ T o Deactivate ....................... 1 3 4 ▫ T o Resume Speed .................... 1 3 5 ▫ T o V ary The Speed Setting .
䡵 Cupholders .......................... 1 4 6 ▫ Front Instr ument Panel Cupholders (40–20–40 Seats) ..................... 1 4 6 ▫ Front Instr ument Panel Cupholders (Bucket Seats) ....................... 1 4 7 ▫ Rear Cupholder (Quad Cab 威 )— If Equipped .
MIRRORS Inside Day/Night Mirror Headlight glare can be r educed by moving the small control under the mirr or to the night position (toward the rear of the vehicle). The mirr or should be adjusted while set in the day position (toward the windshield).
Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glar e from vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirror . A light in the button will illuminate to indicate when the dim- ming feature is activated.
W ARNING! V ehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object.
Set the top switch to the left or right for the left or right mirror , and set it to the center off position to pr event accidentally moving a mirror when you ar e finished adjusting the mirror . T o adjust a mirror , select left or right with the top switch, and press one of the four arr ows for the direction you want the mirr or to move.
NOTE: Fold the trailer towing mirrors r earward prior to entering an automated car wash. A small blindspot mirror is integrated onto the main mirror surface.
HANDS-FREE COMMUNICA TION (UConnect 姞 )— IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated Hands-Free Communication (UConnect 威 ) system. Refer to your “Navigation User’s Manual” for UConnect 威 system operating instructions for these ra- dios.
The UConnect 威 system is driven through your Bluetooth 威 “Hands-Free Pr ofile” cellular phone. UConnect 威 features Bluetooth 威 technology - the global standard that enables dif ferent elec.
The UConnect 威 system is fully integrated with the vehi- cle’s audio system. The volume of the UConnect 威 system can be adjusted either from the radio volume contr ol knob or from the steering wheel radio contr ol (right switch), if so equipped.
Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say ⬙ Help ⬙ following the beep. The UConnect 威 system will play all the options at any prompt if you ask for help. T o activate the UConnect 威 system from idle, simply pr ess the PHONE button and follow the audible prompts for directions.
• For identification purposes, you will be prompted to give the UConnect 威 system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • Y ou will then be asked to give your cellular phone a priority level between one and seven, with one being the highest priority .
• The system will prompt you to say the name of the person you want to call. • After the ⬙ Ready ⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙ John Doe, ⬙ where John Doe is a pr evi- ously stored name entry in the UConnect 威 phonebook or downloaded phonebook.
The UConnect 威 system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations.
• This downloaded phonebook cannot be edited or deleted on the UConnect 威 . These can only be edited on the mobile phone. The changes are transferr ed and updated to UConnect 威 on the next phone connection.
• Press the PHONE button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook Edit. ⬙ • Y ou will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit.
• After you enter the name, the UConnect 威 system will ask you which designation you wish to delete: home, work, mobile, pager , or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted.
NOTE: The user can also exercise ⬙ Edit ⬙ or ⬙ Delete ⬙ operations at this point. • The UConnect 威 system will then prompt you as to the number designation you wish to call.
NOTE: The UConnect 威 system compatible phones in the market today do not support rejecting an incoming call when another call is in progr ess. Therefore, the user can only answer an incoming call or ignore it.
Three-W ay Calling T o initiate three-way calling, pr ess the VOICE RECOG- NITION button while a call is in progr ess, and make a second phone call, as described under ⬙ Making a Second Call While Current Call is in Pr ogress.
• After the ignition key is switched to OFF , a call can continue on the UConnect 威 system for a certain dura- tion, after which the call is automatically transferred from the UConnect 威 system to the mobile phone. • An active call is automatically transferred to the mobile phone after the ignition key is switched to OFF .
• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Emergency ⬙ and the UConnect 威 system will instr uct the paired cellular phone to call the emer gency num- ber .
NOTE: • The towing assistance number dialed is based on the country where the vehicle is pur chased (1-800-528- 2069 for the U.S., 1-877-213-4525 for Canada, 55-14- 3454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico). • If supported, this number may be programmable on some systems.
or sequence of numbers, followed by ⬙ Send, ⬙ is also to be used for navigating through an automated customer service center menu structur e, and to leave a number on a pager . Y ou can also send stored UConnect 威 phonebook entries as tones for fast and easy access to voice mail and pager entries.
• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Confirmations. ⬙ The UConnect 威 system will play the current confirmation pr ompt status and you will be given the choice to change it.
In order to un-mute the UConnect 威 system: • Press the VOICE RECOGNITION button. • Following the beep, say ⬙ Mute off. ⬙ Advanced Phone Connectivity T ransfer Call to and from Cellular Phone The UConnect 威 system allows ongoing calls to be trans- ferred fr om your cellular phone to the UConnect 威 system without terminating the call.
Select Another Cellular Phone This feature allows you to select and start using another phone paired with the UConnect 威 system. • Press the PHONE button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Select Phone ⬙ and follow the prompts.
V oice T raining For users experiencing difficulty with the system r ecog- nizing their voice commands or numbers, the UConnect 威 system V oice T raining feature may be used. T o enter this training mode, follow one of the two following proce- dures: From outside the UConnect 威 mode (e.
• low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some.
• low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity , echo, and loudness to a large degr ee rely on the phone and network, and not the UConnect 威 system.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 109 3.
1 10 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 1 1 1 3.
V oice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all V oice Commands Primary Alternate(s) call cancel confirmation prompt.
V oice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous recor d again redial V oic.
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly appr oved by the party responsible for compliance could void the user’s authority to operate the equipment.
40-20-40 Front Seat The outboard seat portions ar e each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armr est/center storage compartment (if equipped). Each outboard seat is independently adjustable forwar d or rearwar d and is equipped with a back recliner .
W ARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
W ARNING! Y ou can be seriously , even fatally , injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. If you ride in this position, the shoulder harness will no longer be restraining you.
Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decr eases the lumbar (lower back) support. Power Seats — If Equipped The power seat controls ar e on the outboard side of the front seat cushions.
CAUTION! Do not put anything under a power seat. It may cause damage to the seat or seat controls. The four-way switch in the center can be moved forwar d or backward to get the most comfortable position. The same switch can be moved up and down to control seat height.
Change the seat angle by using the two toggle switches, tilting it up or down. Heated Seats — If Equipped The heated seat switches are located in the instr ument panel under the climate controls. Press the switch once for High heat. Pr ess the switch a second time for Low heat.
Low is selected just the lower light will illuminate. Flashing indicator lights on the switch indicate that the heated seat system needs servicing. See your authorized dealer .
2. Reach into the opening beneath the center of the grille and push upward on the safety latch to r elease it before raising the hood. CAUTION! T o prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage.
LIGHTS The headlight switch is located on the left side of the instrument panel next to the steering wheel. Interior Lights Courtesy and dome lights are turned on when the fr ont doors are opened, whe.
NOTE: Quad Cab 威 models may have an optional switched dome lamp that may be operated by pressing the lens. Battery Saver T o protect the life of your vehicle’s battery , load shedding is provided for both the interior and exterior lights.
The headlight delay time is programmable on vehicles equipped with the Electronic V ehicle Information Center (EVIC). For details, refer to “Personal Settings (Customer-Pr ogrammable Features)” under “Overhead Console with Electronic V ehicle Information Center (EVIC) – If Equipped” in Section 3.
T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. T o remove r oad dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.
T urn Signals Move the lever up or down to signal a right-hand or left-hand turn. The arrow on either side of the instr ument cluster flashes to indicate the direction of the turn, and pr oper operation of the front and r ear turn signal lights.
Flash-to-Pass Y ou can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer - ing wheel. This will cause the High beam headlights to turn on until the lever is released.
WINDSHIELD WIPERS AND W ASHERS The wipers and washers are operated by a switch in the multifunction lever . T urn the end of the handle to select the desired wiper speed.
W ARNING! Sudden loss of visibility through the windshield could lead to an accident. Y ou might not see other vehicles or other obstacles. T o avoid sudden icing of the windshield during freezing weather , warm the windshield with the defroster before and during windshield washer use.
W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.
Adjustment 1. Position the driver seat so that you are at least 10 in (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, in the direction you desir e to move the pedals.
ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Contr ol takes over accelerator operation at speeds greater than 25 mph (40 km/h).
NOTE: The Electronic Speed Contr ol system has been designed to shut down if multiple speed control switch buttons (i.e., SET and CANCEL) are operated simulta- neously , in order to ensure pr oper operation. The system can be reactivated by pushing the Electr onic Speed Control switch ON/OFF button and r eestablishing the desired vehicle SET speed.
T o Resume Speed T o resume a pr eviously set speed, push and release the RESUME button. Resume can be used at any speed above 30 mph (50 km/h). T o V ary The Speed Setting When the Electronic Speed Contr ol is on, speed can be increased by pr essing and holding the RESUME/ACCEL button.
W ARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Y our ve- hicle could go too fast for the conditions, and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy , snow-covered, or slippery .
US/M Button Use this button to change the display from U.S. to metric measurement units. Reset Button Use this button to reset the following displays: A verage Fuel Economy (A VG ECO) T rip Odometer (.
Step Button Use this button to choose or cycle through the four trip conditions. A verage Fuel Economy (A VG ECO) Shows the average fuel economy since the last reset. A verage fuel economy is a running average of the amount of fuel used and the distance the vehicle has traveled.
Distance T o Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by weighted average of the instantaneous and average fuel economy , according to the current fuel tank level.
This display shows the distance traveled since the last reset. Resetting of this scr een will cause the trip odometer to change to zero. Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. Resetting the elapsed time will cause the display to change to zero.
W ARNING! Even if the display still reads a few degrees above 32°F (0°C), the road surface may be icy , particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.
After completing up to three 360 degr ee turns, with the vehicle traveling less than 5 mph (8 km/h), in an area fr ee from lar ge metal or metallic objects, the CAL symbol will turn off and the compass will function normally .
Compass V ariance is the difference between magnetic North and geographic North. In some areas of the country , the difference between magnetic and geographic North is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass V ariance Map.
ELECTRICAL POWER OUTLETS The auxiliary electrical outlet can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The outlet is located in the instru- ment panel below and to the right of the climate control panel.
CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e., cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
CUPHOLDERS Front Instrument Panel Cupholders (40–20–40 Seats) Y our new vehicle is equipped with two adjustable cup- holders. The cupholder is opened by pulling on the cupholder door handle, on the front surface. Each open- ing in the cupholder is adjustable and will hold cups and mugs of various sizes.
Front Instrument Panel Cupholders (Bucket Seats) If your new vehicle is equipped with bucket seats there are thr ee cupholders located on the front of the center console. Rear Cupholder (Quad Cab 姞 ) — If Equipped Quad Cab 威 vehicles may be equipped with a rear cup- holder that consists of two cupwells for rear passenger convenience.
STORAGE Center Storage Compartment (40–20–40 Seat) — If Equipped The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid.
W ARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright. • In an accident, the latch may open if the total weight of the items stored exceeds about 10 lbs (4.
Center Storage Compartment (Bucket Seats) — If Equipped Push the upper button on the front of the armr est to raise the upper cover . Inside is a power outlet (if equipped), a cut out for a cell phone charger cor d, removable coin holder (if equipped), and a divider to configure the storage area into separate compartments.
W ARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright. • In an accident, the latch may open if the total weight of the items stored exceeds about 10 lbs (4.
Storage and Seats (Quad Cab 姞 Models) Located in the center of the front 40–20–40 seat cushion there is a storage compartment. Regular Cab models also have storage behind the seat. The Quad Cab 威 models provide additional storage under the rear seat.
Plastic Grocery Bag Retainers Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat.
Power Sliding Rear Window — If Equipped The power sliding rear window switch is located on the instrument panel below the climate contr ols. Press the right side of the switch to open the glass and the left side of the switch to close the glass.
Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position.
Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor . 3. Lift the load floor up to access storage under the load floor .
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Featur es ............... 1 6 0 䡵 Instrument Cluster .................... 1 6 1 䡵 Instrument Cluster Description ............ 1 6 2 䡵 Electronic Digital Clock ................. 1 7 2 ▫ Clock Setting Procedur e .
䡵 Sales Code REF — AM/FM/CD (Single-Disc) Radio W ith Optional Satellite Radio And Hands-Free Phone Capability .............. 1 8 7 ▫ Operating Instructions - Radio Mode ...... 1 8 7 ▫ Operating Instructions - CD Mode ........ 1 9 1 ▫ Operating Instructions - Auxiliary Mode .
䡵 V ideo Entertainment System™ (Sales Code XR V) — If Equipped .................... 2 0 1 䡵 Remote Sound System Controls — If Equipped .......................... 2 0 1 ▫ Radio Operation ..................... 2 0 2 ▫ T ape Player ........
INSTRUMENT P ANEL FEA TURES 1 - Headlight Switch 6 - Passenger Airbag 1 1 - Exhaust Brake Switch* 16 - Parking Brake Release Lever 2 - Air Outlets 7 - Glove Compartment 12 - Power Sliding Back Glass S.
INSTRUMENT CLUSTER UNDERST ANDING YOUR INSTRUMENT P ANEL 161 4.
INSTRUMENT CLUSTER DESCRIPTION 1. Check Gauges This light illuminates when the V oltmeter , Engine Oil Pressur e or Engine Coolant T emperature gauges indicate a reading either too high or too low . Examine the gauges carefully , and follow the instructions contained below for each indicated problem.
4. T achometer The tachometer indicates engine speed in revolutions per minute. CAUTION! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine damage may occur . 5. Airbag W arning Light The indicator lights and remains lit for six to eight seconds when the ignition is first turned on.
9. Oil Pressur e Gauge The pointer should always indicate some oil pres- sure when the engine is r unning. A continuous high or low reading, under normal driving conditions, may indicate a lubrication system malfunction. Immedi- ate service should be obtained.
The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather , up mountain grades, or when towing a trailer . It should not be allowed to exceed the upper limits of the normal operating range. CAUTION! Driving with a hot engine cooling system could damage your vehicle.
15. Shift Lever Indicator (Automatic T ransmission Only) This display indicator shows the automatic transmission shift lever selection. NOTE: Y ou must apply the brake before shifting fr om P ARK. 16. Odometer/T rip Odometer The odometer shows the total distance the vehicle has been driven.
button down for a period of six seconds. The odometer will change to trip value first, then it will display the engine hour value. The engine hours will be displayed for a period of 30 seconds until the ignition is turned off or the engine is started.
18. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir , it indicates a possible brake hydraulic system malfunction or a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Pr ogram (ESP) sys- tem.
Operation of the Brake W arning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approxi- mately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected.
engine is running, immediate service is r equired and you may experience reduced performance, an elevated/ rough idle or engine stall and your vehicle may r equire towing. The light will come on when the ignition is first turned on and remain on for 15 seconds as a bulb check.
26. Low Fuel Light This light illuminates when the pointer is between “E” and 1/8 indication mark (approximately 15% of tank volume) on the fuel gauge.
3. After the hours are adjusted, pr ess the right side T une/Audio control to set the minutes. 4. Adjust the minutes using the right side T une/Audio control.
Power Switch/V olume Control (Rotary) Press the ON/VOL control to turn the radio ON. Pr ess the ON/VOL a second time to turn OFF the radio. Electronic V olume Control The electronic volume contr ol turns continuously (360 degrees) in either dir ection without stopping.
SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to sear ch for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. T o stop the search, pr ess SCAN a second time.
AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the T one, Balance, and Fade Press the r otary TUNE control and BASS will display . T urn the TUNE control to the right or left to incr ease or decrease the Bass tones. Press the r otary TUNE control a second time and MID will display .
T oggle the PTY button to select the following format types: Program T ype 16 Digit-Character Display No program type or un- defined None Adult Hits Adult_Hits Alert Alert Alert Alert Classical Classi.
By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program T ype) mode, the PTY mode will be exited and the radio will tune to the preset station.
Operation Instructions - (CD MODE for CD Audio Play) NOTE: • The ignition switch must be in the ON or ACC position to operate the radio. • Note: This Radio is capable of playing compact discs (CD).
SEEK Button (CD MODE for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the curr ent selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Radio display will show ⬙ EJECTING DISC ⬙ when the disc is being ejected and prompt the user to r emove the disc. Press and hold the LOAD/ EJECT button for 5 seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
RND/PTY Button (Random Play Button) (CD MODE for CD Audio Play) Press this button while the CD is playing to activate Random Play . This feature plays the selections on the compact disc in random order to pr ovide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
• Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙ . ⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙ . ⬙ and a 3-character extension) Multisession disc formats are supported by the radio.
ID3 T ag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pr o files are not supported. Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium.
LOAD/EJECT Button (CD Mode for MP3 Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the push- button with the corresponding number wher e the CD is being loaded. The radio will display PLEASE W AIT and prompt when to INSER T DISC. After the radio displays ⬙ LOAD DISC ⬙ insert the CD into the player .
Press and hold the MSG or INFO button while in the message display priority mode or elapsed time display priority mode will display the song title for each file. R W/FF (CD Mode for MP3 Play) Press the FF side of the button to move forwar d through the MP3 selection.
SALES CODE REF — AM/FM/CD (SINGLE-DISC) RADIO WITH OPTIONAL SA TELLITE RADIO AND HANDS-FREE PHONE CAP ABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Mode Button (Radio Mode) Press the MODE button r epeatedly to select between the CD player and Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and r elease the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the TUNE/AUDIO con- trol. 3. After the hours are adjusted, pr ess the TUNE/AUDIO control to set the minutes. The minutes will begin to blink.
Press the r otary TUNE control a fourth time and BAL will display . T urn the TUNE control to the right or left to adjust the sound level from the right or left side speakers.
Operating Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display .
SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. T o stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal.
MP3 player , cassette player , or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. The auxiliary mode becomes active when an electrical device is plugged into the AUX jack using a standard 3.
R W/FF (Auxiliary Mode) No function. RND/SET Button (Auxiliary Mode) No function. Mode Button (Auxiliary Mode) Press the MODE button r epeatedly to select between the CD player and Satellite Radio (if equipped).
menus and instructions for selecting a variety of destina- tions and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability . Mapping information for navigation is supplied on a DVD that is loaded into the unit. One map DVD covers all of North America.
2. T o show the GPS clock, select “Displayed Clock: GPS Clock” and press ENTER. 3. T o adjust the time zone, Select “T ime Zone” and press ENTER. Select the appropriate time zone and pr ess ENTER. 4. T o turn daylight savings on or off, select “Daylight Savings” and press ENTER.
3. T o decrease the clock by one hour , use the Select Encoder to highlight the “-” sign. Press ENTER. Pr ess ENTER again to decrease the clock by another hour . 4. T o increase the clock by minutes, make sur e “MIN +” is highlighted and press ENTER.
number 888-539-7474, or visit the Sirius web site at www .sirius.com, or at www .siriuscanada.ca for Cana- dian residents. Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1.
W ith the ignition in the ACC position and the radio off, press the CD Eject and SET buttons simultaneously until the 12 digits of the ESN/SID appear on the screen. Selecting Satellite Mode in REF , RAQ, And RAK Radios Selecting Satellite Mode — REF Radio Press the MODE button r epeatedly until the word ⬙ SA T ⬙ appears in the display .
Storing And Selecting Preset Channels In addition to the 12 AM and 12 FM preset stations, you may also commit 12 satellite stations to pushbutton memory . These satellite channel preset stations will not erase any AM or FM preset memory stations. Follow the memory preset pr ocedures that apply to your radio.
Reception Quality Satellite reception may be interr upted due to one of the following reasons: • The vehicle is parked in an undergr ound parking structur e or under a physical obstacle. • Dense tree coverage may interr upt reception. • Driving under wide bridges or along tall buildings can cause intermittent reception.
The right-hand control is a r ocker type switch with a button in the center . Pressing the top of the switch will increase the volume and pr essing the bottom of the switch will decrease the volume. The center button of the right-hand control will allow you to change the mode.
If you press the switch up or down twice it plays the second track, three times, it will play the thir d, etc. The button in the center of the left-hand switch has no function in this mode. CD/DVD MAINTENANCE T o keep a CD/DVD in good condition, take the following precautions: 1.
CLIMA TE CONTROLS The controls for the heating and ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desir ed interior conditions.
NOTE: T o improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots. Panel Outside air flows through the outlets located in the instrument panel.
Blower Control The rotary knob on the left of the control panel is the blower contr ol. T urn the knob clockwise to one of the four positions to obtain the blower speed you desire.
Air Conditioning and Heating — If Equipped Air Conditioning Operation T o turn on the air conditioning, set the fan control at any speed and pr ess the snowflake button located at the right of the control panel. Conditioned air will be directed thr ough the outlets selected by the mode control.
NOTE: T o improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots.
Blower Control The rotary knob on the left of the control panel is the blower contr ol. T urn the knob clockwise to one of the four positions to obtain the blower speed you desire.
Air Conditioning With Dual Zone T emperature Control — If Equipped W ith the Dual Zone T emperature Contr ol System, each front seat occupant can independently contr ol the tem- perature of air coming fr om the outlets on their side of the vehicle.
Recirculation Pushbutton Pushing the Recirculation button al- lows interior air to recir culate continu- ously in any position except defrost and defrost/floor mode for rapid cool down of the interior . Refer to “Fast Cooldown” in this section. Mode Control The mode control allows you to choose from several patterns of air distribution.
Mix Outside air flows in equal proportions thr ough the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defr oster outlets located at the base of the windshield and side window demist outlets.
Dual Zone T emperature Control Use this control to r egulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature contr ol slides for both the driver and front passenger . The blue area of the scale indicates cooler temperatures, while the r ed area indi- cates warmer temperatures.
Operating Tips Fast Cooldown For a fast cooldown, turn the blower fan rotary knob to the extreme right position, turn the mode contr ol to the panel fresh position, pr ess the snowflake button to turn on the air conditioning, and drive with the windows open for the first few minutes.
smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Summer Operation Air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to pr ovide proper corr osion protection and to raise the boiling point of the coolant for protection against over heating.
Operating Tips Chart 216 UNDERST ANDING YOUR INSTRUMENT P ANEL.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es .................... 2 2 1 ▫ Normal Starting ..................... 2 2 1 ▫ Automatic T ransmission ............... 2 2 1 ▫ If Engine Fails T o Start ................ 2 2 2 ▫ After Starting .
▫ Electronically Shifted T ransfer Case Operating Information/Precautions (4 Position Switch) — If Equipped .......... 2 4 2 ▫ Shifting Procedur e — Electronically Shifted T ransfer Case ....................... 2 4 6 䡵 Limited-Slip Differ ential – If Equipped .
䡵 Supplemental T ire Pr essure Information — If Equipped .......................... 2 7 6 䡵 T ire Chains .......................... 2 7 6 䡵 Snow T ires .......................... 2 7 8 䡵 T ire Rotation Recommendations ........... 2 7 9 ▫ Dual Rear Wheels .
䡵 Recreational T owing (Behind Motorhome, Etc.) . 304 ▫ Recreational T owing – 2-Wheel Drive Models ................. 3 0 4 ▫ Recreational T owing – 4-Wheel Drive Models .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. The starter should not be operated for more than 15- second intervals. W aiting a few seconds between such intervals will protect the starter fr om overheating.
NOTE: This vehicle is equipped with a transmission shift interlocking system. The brake pedal must be depressed to shift out of P ARK. T ip Start Feature Do not press the accelerator . T urn the ignition key briefly to ST ART position, and r elease it.
W ARNING! (Continued) • If the vehicle has a discharged battery , booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly . Refer to “Jump Starting” in Section 6.
AUTOMA TIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
DRIVE position. Pull the shift lever toward you when shifting into REVERSE, SECOND, FIRST or P ARK, or when shifting out of P ARK. Gear Ranges DO NOT race the engine when shifting from P ARK or NEUTRAL position into another gear range. P ARK This gear position supplements the parking brake by locking the transmission.
W ARNING! (Continued) • It is dangerous to move the shift lever out of P ARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. Y ou could lose control of the vehicle and hit someone or something.
NOTE: Use caution when operating a heavily loaded vehicle in SECOND or FIRST gear selections in high ambients as torque converter slip can impose significant additional heat load on the cooling system. Overdrive Operation The overdrive automatic transmission contains an elec- tronically contr olled fourth and fifth (if equipped) speed (Overdrive).
The transmission will downshift from Over drive to DRIVE if the accelerator pedal is fully depressed at vehicle speeds above approximately 35 mph (56 km/h). When T o Use “TOW HAUL” and “O/D OFF” Modes When driving in hilly areas, towing a trailer , carrying a heavy load, etc.
economy) and automatic closed-throttle downshifts to 3rd gear ar e performed (for improved braking) when driving conditions warrant. Pressing the “T OW HAUL O/D OFF” button a second time to select O/D OFF will disable 4th and 5th gear completely , which should elimi- nate any excessive transmission shifting.
the transmission. This condition is normal and will not cause damage to the transmission. The torque con- verter will refill within five seconds of shifting fr om P ARK into any other gear position.
at a given road speed. T ake care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of 4-wheel drive vehicles depends on tires of equal size, type and cir cumference on each wheel. Any differ ence will adversely affect shifting and can cause damage to the transfer case.
For additional information on the appropriate use of each transfer case mode position see the information below: 2H Rear Wheel Drive High Range - Normal street and highway driving. Dry hard surfaced r oads. 4H 4-Wheel Drive High Range - Locks the front and r ear driveshafts together .
Shifting Procedure - Manually Shifted T ransfer Case 2H ⇔ 4H Shifting between 2H and 4H can be made with the vehicle stopped or in motion. If the vehicle is in motion, shifts can be made up to 55 mph (88 km/h).
• Shifting into or out of 4L is possible with the vehicle completely stopped, however difficulty may occur due to the mating clutch teeth not being properly aligned. Several attempts may be requir ed for clutch teeth alignment and shift completion to occur .
This Electronically Shifted transfer case pr ovides 5 mode positions: 2-wheel drive (2WD), 4WD AUTO, 4WD LOCK, NEUTRAL and 4WD LOW . The Electronically Shifted transfer case is designed to be driven in the 2 wheel drive position (2WD) or 4-wheel drive position (4WD AUTO) for normal street and high- way conditions (dry hard surfaced r oads).
NOTE: The transfer case NEUTRAL position is selected by depressing the r ecessed button located on the lower left hand corner of the 4WD Control Switch. The transfer case NEUTRAL position is to be used for recreational towing only . Refer to “Recreational T owing” in this section for specific procedur es on shifting into and out of NEUTRAL.
If One or More Shift Conditions are not Met 1. The indicator light for the current position will r emain ON. 2. The newly selected position indicator light will con- tinue to flash.
Proper operation of 4-wheel drive vehicles depends on tires of equal size, type and cir cumference on each wheel. Any differ ence in tire size can cause damage to the transfer case. Because 4-wheel drive provides impr oved traction, there is a tendency to exceed safe turning and stopping speeds.
4WD LOW 4-Wheel Drive Low Range - Low speed 4-wheel drive. Locks the front and r ear driveshafts together . Forces the front and r ear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only .
remain ON and the newly selected position indicator light will continue to flash until all the requir ements for the selected position have been met. T o retry a shift: return the contr ol knob back to the original position, make certain all shift requir ements have been met, wait five seconds and try the shift again.
3. While still rolling, r otate the transfer case control switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear . Alternate Procedure 1. Bring the vehicle to complete stop.
Electronically Shifted T ransfer Case Operating Information/Precautions (4 Position Switch) — If Equipped This is an electric shift transfer case and is operated by the 4WD Control Switch (T ransfer Case Switch), which is located on the instrument panel.
positions on dry hard surfaced r oads may cause in- creased tir e wear and damage to the driveline compo- nents. NOTE: The transfer case NEUTRAL position is selected by depressing the r ecessed button located on the lower left hand corner of the 4WD Control Switch.
If One or More Shift Conditions Are Not Met: 1. The indicator light for the current position will r emain ON. 2. The newly selected position indicator light will con- tinue to flash.
4WD LOCK positions at a given road speed. T ake care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of 4-wheel drive vehicles depends on tires of equal size, type and cir cumference on each wheel. Any differ ence in tire size can cause damage to the transfer case.
4WD LOCK 4-Wheel Drive Lock Range - Locks the front and r ear driveshafts together . Forces the front and r ear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only . 4WD LOW 4-Wheel Drive Low Range - Low speed 4-wheel drive.
remain ON and the newly selected position indicator light will continue to flash until all the requir ements for the selected position have been met. T o retry a shift: return the contr ol knob back to the original position, make certain all shift requir ements have been met, wait five seconds and try the shift again.
Shifting can be performed with the vehicle rolling 2 to 3 mph (3 to 5 km/h) or completely stopped. USE EITHER OF THE FOLLOWING PROCEDURES: Preferred Procedure 1. W ith engine running, slow vehicle to 2 to 3 mph (3 to 5 km/h). 2. Shift the transmission into NEUTRAL.
LIMITED-SLIP DIFFERENTIAL – IF EQUIPPED The limited-slip differ ential provides additional traction on snow , ice, mud, sand and gravel, particularly when there is a dif ference between the traction characteristics of the surface under the right and left rear wheels.
DRIVING ON SLIPPER Y SURF ACES When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and r oad surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability .
Shallow Standing W ater Although your vehicle is capable of driving through shallow standing water , consider the following Caution and W arning before doing so.
W ARNING! • Driving through standing water limits your vehi- cle’ s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water . • Driving through standing water limits your vehi- cle’ s braking capabilities, which increases stop- ping distances.
W ARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible.
P ARKING BRAKE The foot-operated parking brake is positioned below the lower left corner of the instrument panel. T o r elease the parking brake, pull the parking brake release handle. NOTE: The instrument cluster r ed brake warning light will come on and flash to indicate that the parking brake is applied.
W ARNING! • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury . Also be certain to leave the transmission in P ARK. Failure to do so may allow the vehicle to roll and cause damage or injury .
Four-Wheel Anti-Lock Brake System W ARNING! • Anti-Lock Brake Systems (ABS) contain sophisti- cated electronic equipment. It may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability .
The system’s pump motor runs during an ABS stop to provide r egulated hydraulic pressure. The pump motor makes a low humming noise during operation. This is normal. When you are in a sever e braking condition involving use of the ABS, you will experience some pedal drop as the vehicle comes to a complete stop.
TIRE SAFETY INFORMA TION Tire Markings NOTE: • P (Passenger) - Metric tir e sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tir e sizing is based on European design standards.
molded into the sidewall preceding the size designa- tion. Example: T145/80D18 103M. • High flotation tire sizing is based on U.S. design standards and it begins with the tir e diameter molded into the sidewall. Example: 31x10.5 R15 L T . T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.
EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can ca.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however , the date code may only be on one side. T ires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressure is listed on the driver’s side B-Pillar . T ire and Loading Information Placard This placard tel.
T o determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the T ire and Loading Information placar d.
6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
ST ARTING AND OPERA TING 265 5.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
W ARNING! (Continued) • Unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread.
CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard are always “cold tire inflation pr essure.
T ire Inflation Pressure — 4500/5500 with Steel Carcass Ply T ires This type of tire utilizes steel cor ds in the sidewall. As such, they cannot be treated like normal light tr uck tires. Adjusting tire pr essure must be performed by personnel trained, supervised and equipped accordingly .
4500/5500 T ire Inflation 270 ST ARTING AND OPERA TING.
When adjusting inflation pressur e to a tire and wheel assembly mounted on a vehicle, use Remote Mount Automatic Inflation Kit (similar to model number #27- cc1021234, available from TEAM PSE (PENT AST AR Ser- vice Equipment-Phone number 1-800-734-4334).
W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. Y ou could have a serious accident resulting in serious injury or death. Don’t drive a vehicle loaded to the maximum capac- ity at continuous speeds above 75 mph (120 km/h).
Tire Spinning When stuck in mud, sand, snow , or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck. Refer to “Freeing A Stuck V ehicle” in Section 6 of this manual.
These indicators are molded into the bottom of the tr ead grooves. They will appear as bands when the tr ead depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tir e should be replaced. Many states have laws requiring tir e replacement at this point.
Information placard for the size designation of your tir e. The service description and load identification will be found on the original equipment tire. Failur e to use equivalent replacement tir es may adversely affect the safety , handling, and ride of your vehicle.
W ARNING! (Continued) • Never use a tire with a smaller load index or capacity , other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. Y ou could lose control and have an accident result- ing in serious injury or death.
CAUTION! (Continued) • Because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Bro- ken chains can cause serious vehicle damage. Stop the vehicle immediately if noise occurs that could suggest chain breakage.
• On 4X2 vehicles, class “U” snow chains are permitted on the rear wheels only of vehicles equipped with L T245/70R17, L T265/70R17, and L T235/80R17 size tires. • On 4X4 Single Rear Wheel (SR W) vehicles, class “U” snow chains are permitted on the r ear wheels only on vehicles equipped with L T265/70R17.
TIRE ROT A TION RECOMMENDA TIONS T ires on the fr ont and rear axles of vehicles operate at differ ent loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns.
Dual Rear Wheels The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tir e in a set. T o check if tires ar e even, lay a straight edge across all four tires. The straight edge should touch all the tir es. CAUTION! 4500/5500 Dual Rear T ires have only one approved direction of rotation.
FUEL REQUIREMENTS 5.7L Gas Engine The 5.7L engine is designed to meet all emissions regulations and pr ovide satisfac- tory fuel economy and performance when using high quality unleaded gasoline hav- ing an octane range of 87 to 89. The manu- facturer r ecommends the use of 89 octane for optimum performance.
W e strongly support the use of r eformulated gasolines. Properly blended r eformulated gasolines will provide excellent performance and durability for the engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE.
allowed in the United States. MMT is prohibited in Federal and California reformulated gasoline. Materials Added T o Fuel All gasolines sold in the United States are r equired to contain effective deter gent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost.
CAUTION! (Continued) • The use of fuel additives which are now being sold as octane enhancers is not recommended. Many of these products contain high concentra- tions of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer .
W ARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnor- mal conditions repaired promptly . Until repaired, drive with all side windows fully open.
W ARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel to the vehicle when the engine is running. This is in violation of most state and federal fire regulations and will cause the MIL to turn on.
VEHICLE LOADING Certification Label As requir ed by National Highway T raffic Safety Admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar .
T ire Size The tire size on the Label r epresents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size.
Improper weight distributions can have an adverse ef fect on the way your vehicle steers and handles and the way the brakes operate. CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GA WR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles.
measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross Combination W eight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.
T railer Sway Control The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.
W eight-distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or an authorized r ecreational vehicle dealer for additional information.
T railer Hitch Classification Class Max. GTW (Gross T railer Wt.) Class I - Light Duty 2,000 lbs (907 kg) Class II - Medium Duty 3,500 lbs (1587 kg) Class III - Heavy Duty 5,000 lbs (2268 kg) Class IV.
T railer and T ongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer . This places 10% to 15% of the Gross T railer W eight (GTW) on the tow hitch of your vehicle.
NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options must be considered as part of the total load on your vehicle. Refer to “T ire and Loading Information placard” under “T ire Safety Information” in Section 5.
• When hauling cargo or towing a trailer , do not over- load your vehicle or trailer . Overloading can cause a loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, suspension, chas- sis structur e or tires. • Safety chains must always be used between your vehicle and trailer .
− Also, check the trailer tires for pr oper tire inflation pressur es before trailer usage. − Check for signs of tire wear or visible tir e damage before towing a trailer . Refer to “T ires–General Infor - mation” in this section. − When replacing tir es, refer to “T ires–General Informa- tion” in this section.
W ARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. Y ou might not have brakes when you need them and could have an accident. • T owing any trailer will increase your stopping distance.
The following chart identifies the maximum electrical loads that the trailer tow output circuits ar e capable of supporting. T railer T ow Additional Lamp Loads Output Functions Maximum Current Additional Bulbs Al- lowed. Example Only . Other bulb combina- tions can be used as long as maximum cur- rent is not exceeded.
NOTE: Check the automatic transmission fluid level before towing. T owing T ips — T ow/Haul (If Equipped) T o reduce potential for automatic transmission over heat- ing, turn the “TOW HAUL OD/OFF” feature ON when driving in hilly areas or shift the transmission to Drive position 2 on more sever e grades.
Dodge Body Builders Guide. See your authorized dealer , installer or snowplow manufacturer for this information. There ar e unique electrical systems that must be con- nected to properly assur e operator safety and prevent overloading vehicle systems.
Snowplow Prep Package Model A vailability For Information about snowplow applications visit www .dodge.com or refer to the current Dodge Body Builders Guide. 1. The maximum number of occupants in the truck should not exceed two. 2. The total GVWR or the Front GA WR or the Rear GA WR should never be exceeded.
Over the Road Operation With Snowplow Attached The blade restricts air flow to the radiator and causes the engine to operate at higher than normal temperatures. Therefor e, when transporting the plow , angle the blade completely and position it as low as road or surface conditions permit.
• Operate with transfer case in 4L when plowing small or congested areas wher e speeds are not likely to exceed 15 mph (24 km/h). At higher speeds operate in 4H. • V ehicles with automatic transmissions should use 4L range when plowing deep or heavy snow for extended periods of time to avoid transmission overheating.
Recreational T owing – 4-Wheel Drive Models CAUTION! Failure to follow these requirements can cause severe damage to the transmission and/or transfer case. NOTE: Both the manual shift and electronic shift trans- fer cases must be shifted into NEUTRAL for recr eational towing.
9. Repeat steps 7 and 8 with the transmission in DRIVE. 10. Shut OFF the engine and place the ignition key in the unlocked OFF position. 1 1. Shift transmission into P ARK. 12. Apply the parking brake. 13. Attach vehicle to tow vehicle with tow bar . 14.
W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake.
3. T urn the ignition key to the ON position, but do not start the engine. 4. Depress the brake pedal. 5. Shift transmission into NEUTRAL. 6. Using the point of a ballpoint pen or similar object, depress the r ecessed transfer case NEUTRAL button for four seconds.
• The ignition key must be ON for a shift to take place and for the position indicator lights to be operable. If the key in not ON, the shift will not take place and no position indicator lights will be on or flashing. • Flashing NEUTRAL position indicator light indicates that shift requir ements have not been met.
NOTE: • The transfer case cannot be shifted into NEUTRAL from the 4AUT O (if equipped) position. • Steps 1 through 5 ar e requirements that must be met prior to depressing the transfer case Neutral (N) button, and must continue to be met until one second elapses and the shift has been completed.
CAUTION! • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and fluid loss will damage internal parts.
.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher ................ 3 1 4 䡵 Jacking And T ire Changing ............... 3 1 5 ▫ 3500 Models — If Equipped ............. 3 1 5 ▫ Preparations For Jacking ............... 3 1 6 ▫ Jacking Instructions .
HAZARD W ARNING FLASHER The Hazard W arning flasher switch is mounted on the top of the steering column. Press the button on the top of the steering column to turn on the Hazard W arning flasher . When the Hazard W arn- ing flasher is activated, all directional turn signals will flash off and on to warn oncoming traf fic of an emer- gency .
JACKING AND TIRE CHANGING W ARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
W ARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid accelera- tion, or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury .
6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
W ARNING! (Continued) • If working on or near a roadway , be extremely careful of motor traffic. • T o assure that spare tires, flat or inflated are securely stowed, spares must be stowed with the valve stem facing the ground. • T urn on the Hazard W arning Flasher .
When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Securely place the jack under the sway bar bracket (unless both tires ar e flat on one side, then place jack under shock bracket) facing forward in vehicle.
4. By rotating the wheel wr ench clockwise, raise the vehicle until the wheel just clears the surface. W ARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it.
7. Install wheel center cap (if equipped) and remove wheel blocks. Do not install chrome or aluminum wheel center caps on the spare wheel. This may r esult in cap damage.
CAUTION! • Use a back and forth motion to remove the hub cap. Do not use a twisting motion when removing the hub cap, damage to the hub cap; finish may occur . • The rear hub caps on the dual rear wheel has two pry off notches. Make sure that the hook of the jack handle driver is located squarely in the cap notch before attempting to pull off.
Slots in the wheels will assist in properly orienting the inner and outer wheels. Align these slots when assem- bling the wheels for best access to the tire valve on the inner wheel. The tires of both dual wheels must be completely off the gr ound when tightening to insure wheel centering and maximum wheel clamping.
These dual rear wheels should be tightened as follows: 1. T ighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table.
second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and after 500 miles (800 km). It is recommended that wheel stud nuts be kept tor qued to specifications at all times. T orque wheel stud nuts to specifications at each lubrication interval.
T o Stow The Flat Or Spare — If Equipped Refer to Upfitters Body Builders Guide for information on stowing your spare tir e (if equipped). HOISTING A conventional floor jack may be used at the jacking locations. Refer to the graphics that show jacking loca- tions.
Y our vehicle is equipped with two 12-V olt batteries. If it becomes necessary to use a booster battery with jumper cables to start a vehicle’s engine because its batteries are discharged, the following pr ocedure should be used: Set the parking brake and place the transmission in P ARK.
W ARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. 2. Connect one end of the other jumper cable to negative (-) post of booster battery .
vehicle with the discharged battery . Make sure a good connection is made, free of dirt and gr ease. W ARNING! • Do not connect the cable to the negative post of the discharge battery . The resulting electrical spark could cause the battery to explode.
With Portable Starting Unit There ar e many types of these units available. Follow the manufacturer’s instr uctions for necessary precautions and operation. CAUTION! It is very important that the starting unit operating voltage does not exceed 12-V olts DC or damage to battery , starter motor , alternator , or electrical system may occur .
W ARNING! • Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. • Stand clear of vehicles when pulling with tow hooks. T ow straps and chains may break, causing serious injury . CAUTION! T ow hooks are for emergency use only to rescue a vehicle stranded off-road.
NOTE: The transfer case must be in the neutral position, and the transmission must be in P ARK (automatic trans- mission), or in gear (manual transmission) to tow a 4-Wheel Drive vehicle with one end of the vehicle raised. The manufacturer r ecommends towing with all wheels OFF the ground.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment— 5.7L .............. 3 3 5 䡵 Onboard Diagnostic System (OBD II) ....... 3 3 6 ▫ Loose Fuel Filler Cap Message ........... 3 3 6 䡵 Replacement Parts ..................... 3 3 7 䡵 Dealer Service .
▫ T ransfer Case — If Equipped ............ 3 5 6 ▫ Automatic T ransmission ............... 3 5 6 ▫ Appearance Care And Protection Fr om Corrosion .......................... 3 5 9 䡵 Fuses .............................. 3 6 4 ▫ Integrated Power Module .
ENGINE COMP ARTMENT— 5.7L 1 — Air Cleaner Filter 7 — Engine Oil Dipstick 2 — Automatic T ransmission Dipstick 8 — Power Steering Fluid Reservoir 3 — Engine Oil Fill 9 — W asher Fluid Res.
ONBOARD DIAGNOSTIC SYSTEM (OBD II) V ehicles with 5.7L engines ar e equipped with a sophisti- cated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, en- gine, and automatic transmission control systems.
appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row , the system will turn on the Malfunction Indicator Light (MIL).
MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there ar e fixed maintenance intervals, there ar e other items that should operate satisfactorily without periodic maintenance.
Change Engine Oil Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals. Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that ar e API certified and meet the requir ements of Chrysler Material Standard MS-6395.
Synthetic Engine Oils Y ou may use synthetic engine oils provided the r ecom- mended oil quality requir ements are met, and the recom- mended maintenance intervals for oil and filter changes are followed. Materials Added to Engine Oil Do not add supplemental materials, other than leak detection dyes, to your engine oil.
W ARNING! The air induction system (air cleaner , hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner , hoses, etc) unless such removal is necessary for repair or maintenance.
W ARNING! (Continued) • Battery posts, terminals and related accessories contain lead and lead compounds. W ash hands after handling. CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.
W ARNING! (Continued) • The air conditioning system contains refrigerant under high pressure. T o avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced repair person.
Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner . This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades.
W ARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. After the engine has warmed, operate the defroster for a few minutes to reduce the possibility of smearing or freezing the fluid on the cold windshield.
The catalytic converter requir es the use of unleaded fuel only . Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not requir e maintenance.
W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.
Cooling System W ARNING! Y ou or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator . If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot.
Cooling System — Drain, Flush and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner . Follow with a thorough rinsing to remove all deposits and chemicals.
CAUTION! (Continued) • This vehicle has not been designed for use with Propylene Glycol based engine coolant (anti- freeze). Use of Propylene Glycol based engine coolant (antifreeze) is not recommended. Adding Coolant Y our vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals.
NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifr eeze) and will requir e more frequent engine coolant (antifr eeze) changes.
Disposal of Used Engine Coolant Used ethylene glycol based engine coolant (antifreeze) is a regulated substance r equiring proper disposal. Check with your local authorities to determine the disposal rules for your community .
If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check engine coolant (antifreeze) fr eeze point in the radiator and in the coolant recovery bottle.
The brake master cylinder has a translucent plastic reservoir . On the outboard side of the r eservoir , there is a “MAX” mark and an “MIN” mark (4500/5500 vehicles only). The fluid level must be kept within these two marks. Do not add fluid above the full mark because leakage may occur at the cap.
Rear Axle And 4x4 Front Driving Axle Fluid Level For models with 9.25 in Front Axles and 1 1.5 in Rear Axles, refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. For normal service, periodic fluid level checks are not r equired.
Lubricant Selection Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. NOTE: The presence of water in the gear lubricant will result in corr osion and possible failure of differ ential components.
Parts” in this section for the correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the r ecommended fluid. CAUTION! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder .
6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the HOT (upper) refer ence holes on the dipstick at normal operat- ing temperature. V erify that a solid coating of oil is seen on both sides of the dipstick.
NOTE: If the transmission is disassembled for any reason, the fluid and filter should be changed. It is important that proper lubricant is used in the transmission. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
• Insects, tree sap and tar . • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. W ashing • W ash your vehicle regularly . Always wash your ve- hicle in the shade using MOP AR 威 Car W ash or a mild car wash soap, and rinse the panels completely with clear water .
• If you detect any stone chips or scratches in the paint, touch them up immediately . The cost of such repairs is considered the r esponsibility of the owner . • If your vehicle is damaged due to an accident or similar cause which destroys the paint and pr otective coating, have your vehicle repair ed as soon as pos- sible.
• Blot any remaining stain with a clean, damp towel. • For tough stains, apply MOP AR 威 T otal Clean or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to r emove soap residue. • For grease stains, apply MOP AR 威 Multi-Purpose Cleaner to a clean, damp cloth and remove stain.
Cleaning Headlights Y our vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and ther efore differ ent lens cleaning procedures must be followed.
Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water . Do not remove the belts from the vehicle to wash them.
Cavity Cartridge Fuse Mini Fuse Description 1 20 Amp Y ellow Power Outlet Console 2 20 Amp Y ellow Cabin Compartment Node (CCN) Door Locks 3— — 4 15 Amp Blue Aisin T ransmission Controls (Diesel O.
Cavity Cartridge Fuse Mini Fuse Description 12 30 Amp Pink Electric Brake 13 25 Amp Natural Power-Battery R W AL/ABS Module Feed 14 15 Amp Blue Park Lights Left 15 20 Amp Y ellow T railer Park Lights .
Cavity Cartridge Fuse Mini Fuse Description 27 40 Amp Green Power Seats 28 10 Amp Red Power Run/Start- PCM/Steering Angle Sensor 29 10 Amp Red 4X4 Switch/Pass Dr Switch/EC Mirror 30 15 Amp Blue Power .
Cavity Cartridge Fuse Mini Fuse Description 39 10 Amp Red Seatbelt T ension Reducer/Power IGN Run/Acc 40 20 Amp Y ellow Power IGN Run/Acc — Cigar Lighter/Rear Power Point 41 — — 42 30 Amp Pink D.
VEHICLE STORAGE If you are storing your vehicle for mor e than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw (IOD) fuse located in the Integrated Power Module, located in the engine compartment.
REPLACEMENT LIGHT BULBS LIGHT BULBS — Inside Bulb No. Overhead Console Lights ............... T S 212-2 Dome Light ............................ 7679 NOTE: For lighted switches, see your authorized dealer for replacement instr uctions. All of the inside bulbs are brass or glass-wedge base.
1. Open the hood. 2. Remove the two bolts from the fr ont of the headlight housing. 3. Remove the plug from the inner fender well. MAINT AINING YOUR VEHICLE 371 7.
4. Remove the nut through the access hole. 5. Pull the housing out from the fender to allow r oom to disconnect the electrical connectors. NOTE: For easier removal, pull the headlight assembly straight forward, applying the gr eatest amount of force to the outer edge of the headlight assembly .
6. Unlock and pull connector straight from the base of the headlight halogen bulb. 7. T wist connector on the side marker/turn signal/park light bulb 1 ⁄ 4 turn and remove connector and bulb fr om housing. 8. Remove housing from vehicle with headlight halogen bulb in housing.
Fog Lights 1. Reach under the vehicle, unlock and twist connector counterclockwise 1 ⁄ 4 turn and remove connector and bulb from housing. 2. Pull bulb straight from the connector .
Cab T op Clearance Lights — If Equipped 1. Remove the two screws fr om the top of the light. 2. Rotate the socket 1 ⁄ 4 turn and pull it from the light assembly .
3. Pull the bulb straight from its socket and r eplace. 376 MAINT AINING YOUR VEHICLE.
FLUID AND CAP ACITIES U.S. Metric Fuel (Approximate) Standard Rear T ank 52 Gallons 197 Liters Optional Midship T ank 22 Gallons 83 Liters Engine Oil with Filter 5.7L Engine (SAE 5W -20, API Certified) (For vehicles operating under a gross combined weight rating less than 14,000 lbs.
FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Antifreeze/Coolant 5–Y ear/100,000 Mile Formula HOA T (Hybrid Organic Additive T echnology) Engine Oil (5.7L Engine) (For ve- hicles operating under a gross com- bined weight rating less than 14,000 lbs.
Chassis Component Fluid, Lubricant, or Genuine Part Automatic T ransmission (5-Speed 545RFE) MOP AR 威 A TF+4 Automatic T ransmission Fluid T ransfer Case MOP AR 威 A TF+4 Automatic T ransmission Fluid Front and Rear Axle Fluid (4500/ 5500) GL-5 SAE 75W -90 Synthetic (MS-9763) or equivalent.
.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance ...... 3 8 2 䡵 Maintenance Schedule .................. 3 8 2 ▫ 5.7L Gas Engine .
EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions contr ol system.
• Change your engine oil more often if you drive your vehicle off-r oad for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first. Y our dealer will reset the oil change indicator message after completing the scheduled oil change.
At Each Oil Change • Change the engine oil filter . • Inspect the brake hoses and lines. • Lubricate outer tie rod ends. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle.
6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Lube front drive shaft fitting (4x4 only).
18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Lube front drive shaft fitting (4x4 only). ❏ Lubricate outer tie rod ends. ❏ Inspect the front & rear axle fluid.
30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the spark plugs (5.7L engine). ❏ Lube front drive shaft fitting (4x4 only).
42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Lube front drive shaft fitting (4x4 only).
54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Lube front drive shaft fitting (4x4 only). ❏ Lubricate outer tie rod ends. ❏ Inspect the front & rear axle fluid.
66,000 Miles (1 10,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Lube front drive shaft fitting (4x4 only).
78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Lube front drive shaft fitting (4x4 only).
90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the spark plugs (5.7L engine). ❏ Inspect and replace PCV valve if necessary .
96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter , replace if necessary .
108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter , replace if necessary .
120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the spark plugs (5.7L engine). ❏ Inspect the brake linings, replace if necessary .
132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter , replace if necessary .
144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter , replace if necessary .
† This maintenance is recommended by the manufactur er to the owner , but is not required to maintain emissions warranty . W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 4 0 1 ▫ Prepar e For The Appointment ........... 4 0 1 ▫ Prepar e A List ...................... 4 0 1 ▫ Be Reasonable W ith Requests .
䡵 Publication Order Forms ................ 4 0 5 䡵 Department Of T ransportation Uniform T ire Quality Grades ........................ 4 0 6 ▫ T readwear ......................... 4 0 7 ▫ T raction Grades ..................... 4 0 7 ▫ T emperature Grades .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty .
This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • If for some reason you ar e still not satisfied, talk to the general manager or owner of the authorized dealer- ship.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its customer center .
W ARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
T o contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY : 1–800–424– 9153), or go to http://www .safercar .gov; or write to: Administra- tor , NHTSA, 400 Seventh Street, SW ., W ashington, D.C. 20590.
• Diagnostic Procedure Manuals Diagnostic Procedur e Manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer -controlled ve- hicle systems and features.
T readwear The T readwear grade is a comparative rating, based on the wear rate of the tire when tested under contr olled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
T emperature Grades The temperature grades ar e A (the highest), B, and C, repr esenting the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10.
Adding Fuel ........................... 2 8 5 Adjustable Pedals ....................... 1 3 1 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 340 Air Conditioner Maintenance ............... 3 4 2 Air Conditioning Refrigerant ............. 342,343 Air Conditioning System .
Emergency Starting ..................... 3 2 6 Saving Feature (Pr otection) ............... 1 2 4 Belts, Seat .............................. 3 6 Body Builders Guide ....................... 6 Body Mechanism Lubrication ............... 3 4 3 B-Pillar Location .
Cleaning Wheels ............................. 3 6 1 Climate Control ......................... 2 0 4 Clock ........................ 172,175,189,195 Compact Disc (CD) Maintenance ............. 2 0 3 Compass ........................... 140,141 Compass Calibration .
Door Locks ............................. 2 7 Driving Through Flowing, Rising, or Shallow Standing W ater ........................ 2 5 0 Dual Rear Wheels ..................... 280,322 DVD Player (V ideo Entertainment System™) .... 2 0 1 Electric Rear W indow Defrost .
Fabric Care ............................ 3 6 1 Filters Air Cleaner .......................... 3 4 0 Engine Fuel .......................... 3 7 8 Engine Oil ..................... 338,340,378 Flashers T urn Signal .......................... 1 2 7 Flat T ire Stowage .
Gauges ............................... 1 6 2 Coolant T emperature ................... 1 6 4 Fuel ............................... 1 7 1 Oil Pressur e .......................... 1 6 4 Speedometer ......................... 1 6 3 T achometer .............
Hitches T railer T owing ........................ 2 9 2 Hoisting .............................. 3 2 6 Hood Release .......................... 1 2 1 Hub Caps ............................. 3 2 1 Ignition ............................... 1 2 K e y .......
Lights .............................. 75,123 Airbag ............................ 57,163 Alarm .............................. 1 6 5 Anti-Lock ........................... 1 7 0 Anti-Lock W arning ..................... 2 5 7 Brake W arning ..............
Power Door ........................... 2 8 Steering Wheel ......................... 1 4 Lower Anchors and T ether for CHildren (LA TCH) .............................. 6 4 Lubrication, Body ....................... 3 4 3 Lug Nuts .......................
Change Interval ....................... 3 3 9 Dipstick ............................. 3 3 8 Disposal ............................ 3 4 0 Filter ......................... 338,340,378 Identification Logo ..................... 3 3 9 Materials Added to ....
Power Steering Fluid ..................... 3 7 9 Pregnant W omen and Seat Belts .............. 4 7 Programming T ransmitters (Remote Keyless Entry) .................... 2 4 Radial Ply T ires ......................... 2 7 2 Radiator Cap (Coolant Pressur e Cap) .
Safety Checks Outside V ehicle ............... 7 5 Safety Defects, Reporting .................. 4 0 4 Safety Information, T ire ................... 2 5 8 Safety T ips ............................. 7 3 Satellite Radio ....................... 195,197 Satellite Radio Antenna .
T ransfer Case, Shifting into T ransfer Case Neutral (N) .................... 305,307 T ransfer Case, Shifting out of T ransfer Case Neutral (N) .................... 306,309 Shoulder Belt Upper Anchorage .............. 4 4 Shoulder Belts .............
T ether Anchor , Child Restraint ............. 64,67 T ilt Steering Column ..................... 1 3 0 T ip Start .............................. 2 2 2 T ire and Loading Information Placar d ...... 262,276 T ire Identification Number (TIN) ............
T raction .............................. 2 5 0 T raction Control ......................... 3 5 6 T railer T owing .......................... 2 8 9 Cooling System T ips .................... 3 0 0 Hitches ............................. 2 9 2 Minimum Requirements .
W arning Lights (Instrument Cluster Description) ............. 1 6 2 W arnings and Cautions ..................... 6 W arranty Information ..................... 4 0 4 W ashers, W indshield .................. 130,344 W ashing V ehicle ..................
INST ALLA TION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to pr ovide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel.
2009 RAM TRUCK CHASSIS CAB RAM TR UCK CHASSIS C AB Chrysler LL C 81-326-0926 First Edition Printed in U.S.A. OWNER ’S MANU AL 2009.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Dodge 2009 Ram Chassis Cab c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Dodge 2009 Ram Chassis Cab - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Dodge 2009 Ram Chassis Cab, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Dodge 2009 Ram Chassis Cab va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Dodge 2009 Ram Chassis Cab, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Dodge 2009 Ram Chassis Cab.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Dodge 2009 Ram Chassis Cab. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Dodge 2009 Ram Chassis Cab ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
