Manuel d'utilisation / d'entretien du produit 2008 Caravan du fabricant Dodge
Aller à la page of 531
Car a v an OWNER’ S MANUAL 2008 2008 Car a v an 81-226-0819 First Edition Printed in U.S.A..
VEHICLES SOLD IN CANADA W ith respect to any V ehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor . DRIVING AND ALCOHOL Drunken driving is one of the most fr equent causes of accidents.
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION .............................................................3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ............................... 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
.
INTRODUCTION CONTENTS m Introduction ........................... 4 m How T o Use This Manual .................. 4 m W arnings And Cautions ................... 6 m V ehicle Identification Number ............... 6 m V ehicle Modifications/Alterations ..
INTRODUCTION This Owner’s Manual has been prepar ed with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a W arranty Information Booklet and various customer-oriented documents.
INTRODUCTION 5 1.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es that could result in an accident or bodily injury . It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entir e manual you may miss important infor- mation.
VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS m A W ord About Y our Keys .................. 1 2 ▫ W ireless Ignition Node (WIN) ............. 1 2 m Sentry Key t Immobilizer System ............. 1 5 ▫ Replacement Keys .....................
▫ Power Sliding Side Door — If Equipped ...... 4 2 ▫ Sliding Side Door Child Protection Lock ...... 4 6 m Liftgate ............................... 4 8 ▫ Power Liftgate — If Equipped ............. 4 9 m Storage Bin Safety W arning ...........
▫ Restraining Infants And Small Children W ith Seat Delete Feature (Commer cial V ehicles Only) .... 9 0 m Engine Break-In Recommendations ........... 9 3 m Safety T ips ............................ 9 3 ▫ Safety Checks Y ou Should Make Inside The V ehicle .
A WORD ABOUT YOUR KEYS Y our vehicle uses a keyless ignition system. This system consists of a Remote Keyless Entry (RKE) transmitter with integrated ignition Key and a W ireless Ignition Node (WIN) with integral ignition switch. Y ou can insert the double-sided key into the ignition switch with either side up.
The valet key allows for entry into the vehicle should the battery in the vehicle or the transmitter go dead. The valet key is also for locking the glove box.
2. Insert the integrated ignition key into the ignition switch. 3. T urn the ignition switch to the ST ART position and release it as soon as the starter engages. The starter motor will continue to run and will disengage automatically when the engine begins running.
Key-In-Ignition Reminder If you open the driver’s door with the integrated ignition key in the ignition, a chime will sound to remind you to remove the key . NOTE: The Key-In-Ignition reminder only sounds when the integrated ignition key is placed in the OFF or ACC position.
NOTE: • The Sentry Key t Immobilizer system is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting pr oblems and loss of security protection.
programming a blank transmitter to the vehicle electr on- ics. A blank transmitter is one that has never been programmed. NOTE: When having the Sentry Key t Immobilizer system serviced, bring all vehicle RKE transmitters with you to the authorized dealer .
NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased fr om the sys- tem’s memory . This will prevent the lost key from starting your vehicle. The remaining keys must then be repr ogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be repr o- grammed.
Arming The System Remove the key from the ignition switch and either pr ess a power door lock switch while the driver or passenger door is open or press the LOCK button on the Remote Keyless Entry (RKE) transmitter .
previously described arming sequences has occurr ed, the system will arm regar dless of whether you are in the vehicle or not. If you remain in the vehicle and open a door , the alarm will sound.
REMOTE KEYLESS ENTR Y (RKE) — IF EQUIPPED This system allows you to lock or unlock the doors and liftgate, and activate the P ANIC alarm, optional power liftgate, left power sliding door , and right power sliding door from distances up to about 23 ft (7 m) using a hand-held radio RKE transmitter .
Seven-button transmitters will provide functions that allow the same basic operation as the three-button, but may also be used to OPEN/CLOSE the optional power liftgate, left power sliding door , or right power sliding door .
• For vehicles not equipped with the EVIC, the Remote UNLOCK feature can be enabled or disabled by per - forming the following procedur e: 1. Perform this operation while standing outside the vehicle. 2. Press the LOCK button for five to ten seconds.
Using The P ANIC Alarm T o turn the P ANIC Alarm featur e ON or OFF , press and hold the P ANIC button on the RKE transmitter for at least one second and release. When the P ANIC Alarm is on, the headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on.
Open/Close Power Left Power Sliding Door — If Equipped Press the Left Power Sliding Door button twice on the RKE transmitter within five seconds to Open/Close Power Left Power Sliding Door . If the button is pushed while the door is being power-closed, the door will reverse to the full open position.
The table below explains the Lamp Flash options. Function Which T urn Signal Lamps Number of Flashes Lock All 1 Unlock 1st Press Left Side 2 Unlock All Doors All 2 Left Side Left Side 2 Right Side Right Side 2 Liftgate All 2 Programming Additional RKE T ransmitters Refer to Sentry Key t Immobilizer System “Customer Key Programming.
2. Remove and replace the battery . A void touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch the battery , clean it with rubbing alcohol. 3. Reposition the access door panel over the battery opening and snap into place.
REMOTE ST ARTING SYSTEM — IF EQUIPPED Remote Starting conveniently starts the engine from outside the vehicle by using the Remote Keyless Entry (RKE) transmitter while maintaining the Security Alarm System. The Remote Starting System has a targeted range of 328 ft (100 m).
T o Enter Remote Start Mode Press and r elease the Remote Start button on the RKE transmitter twice, within five seconds. The parking lights will flash and the horn will honk twice (if programmed). Then, the engine will start and the vehicle will remain in the Remote Start mode for a 15 minute cycle.
T o Enter the V ehicle After Remote Start T o enter the vehicle while the engine is running during a Remote Start, you must first unlock the vehicle using the UNLOCK button on the transmitter .
T o T urn Off the Engine While in Remote Start Mode Press and r elease the Remote Start button one time. NOTE: T o avoid inadvertent shut downs, the system will disable the one time press of the Remote Start button for two seconds after receiving a valid Remote Start request.
If the lock plunger is down when you shut the door , the door will lock. Therefor e, make sure the keys are not inside the vehicle before closing the door . W ARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate. This prevents you fr om acciden- tally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate.
Lock Doors Automatically — If Equipped If the Lock Doors Automatically feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
The Lock Doors Automatically at 15 mph (24 km/h) feature can be r eactivated by repeating the above men- tioned procedur e or by performing the procedure in the EVIC, Customer Programmable Featur es section on ve- hicles so equipped.
7. T o reactivate this featur e, repeat the above steps. 8. If a chime is not heard, the pr ogram mode was canceled before the featur e could be changed.
POWER WINDOWS Y ou can control all windows using switches on the driver’s door trim panel. The switches will operate only when the ignition switch is in the ON or ACC position and during power accessory delay .
Power W indow Lockout Switch — If Equipped The driver may lock out all power windows by depressing the bar switch just below the power window switches. Front Passenger Power W indow Switch There is a single switch on the fr ont passenger’s door trim panel which operates the passenger door window and locks and unlocks all doors.
Sliding Side Door Power W indow Switch There is a single switch on each sliding side door which operates the sliding side door window . The switches will operate only when the ignition switch is in the ON or ACC position. NOTE: The sliding door windows do not fully open, stopping several inches above the window sill.
Auto Up Feature W ith Anti–Pinch Protection — If Equipped The left front window switch may be equipped with an Auto Up feature. Lift the window switch to the second detent, release, and the window will go up automatically . T o stop the window from going all the way up during the Auto Up operation, push down on the switch briefly .
2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. W ind Buffeting W ind buffeting can be described as the per ception of pressur e on the ears or a helicopter-type sound in the ears.
• There is a hold-open latch that is activated when the sliding door is fully opened. This latch will keep your sliding door open on any incline. T o close the sliding door after the hold-open latch is activated, you must rock the inside handle forwar d or pull outward on the outside handle.
NOTE: The power sliding side door must be unlocked before the power sliding door switches will operate. If the inside or outside door handles are used while the power sliding side door is activated, the power sliding door feature will be canceled and the door must be opened or closed manually .
• If the power sliding side door is not in the full open or close position, it will fully open when a power sliding door switch is pressed. T o close the door , wait until it is fully open and then press the switch again.
Y ou can turn the feature back on by r epeating the above mentioned procedur e. Power Sliding Side Door Master Lock Switch The power sliding side doors may also be opened by pressing the switches on the over head console or the switches located on the trim panel just in front of the sliding door .
Sliding Side Door Child Protection Lock T o provide a safer envir onment for small children riding in the rear seats, the sliding doors ar e equipped with a child protection door lock system.
NOTE: • After engaging the Child Protection Door Lock, al- ways test the door from the inside to make certain it is in the desired position. • When the Child Protection Door Lock system is en- gag.
LIFTGA TE On vehicles equipped with power locks, the liftgate can be unlocked using the Remote Keyless Entry (RKE) transmitter button, or by activating the power door lock switches located on the front doors.
POWER LIFTGA TE — IF EQUIPPED The power liftgate may be opened manually or by using the button on the Remote Keyless Entry (RKE) transmit- ter . Press the button on the transmitter twice within five seconds, to open the power liftgate.
The power liftgate may be closed by pressing the button, located in the upper left trim in the liftgate opening. Pushing once will only close the liftgate. This button cannot be used to open the liftgate. W ARNING! During power operation, personal injury or cargo damage may occur .
• The power liftgate must be in the full open or close positions for any of the buttons to operate. If the liftgate is not in the full open or close positions, it must be opened or closed manually . • If the liftgate release button is activated while the power liftgate is closing, the liftgate will reverse to the full open position.
Gas props support the liftgate in the open position. However , because the gas pressure dr ops with tempera- ture, it may be necessary to assist the pr ops when opening the liftgate in cold weather . STORAGE BIN SAFETY W ARNING Safety W arnings W ARNING! Always close the storage bin covers when your ve- hicle is unattended.
NOTE: Y our vehicle may be built with a release strap or release lever attached to the Storage Bin Cover latch mechanism. Storage Bin Cover Emergency Release Lever — If Equipped As a security measure, your vehicle may be built with a Storage Bin Cover Emergency Release lever built into the storage bin cover latching mechanism.
Storage Bin Cover Emergency Release Strap — If Equipped As a security measure, your vehicle may be built with a Storage Bin Cover Emergency Release strap built into the storage bin cover latching mechanism.
NOTE: Do not use the storage bin emergency r elease strap to lift the storage bin cover . The strap is intended for emergency r elease only . OCCUP ANT RESTRAINTS Some of the most important safety fea.
• All seat belt systems (except the driver’s, Swivel n’ Go, and third r ow center position) include Automatic Locking Retractors (ALRs), which lock the seat belt webbing into position by extending the belt all the way out and then adjusting the belt to the desired length to restrain a child seat or secur e a large item in a seat.
Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thr own from the vehicle. Seat belts r educe the possibility of ejection and the risk of injury caused by striking the inside of the vehicle.
W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. • W earing your belt in the wrong place could make your injuries in a collision much worse.
2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the r ear seats. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries.
4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
6. T o release the belt, push the r ed button on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow the belt to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
pushing anywhere on the anchorage. T o move the an- chorage downward, squeeze the actuation buttons while simultaneously pushing down on the anchorage assem- bly . As a guide, if you are shorter than average you will prefer a lower position, and if you ar e taller than average you will prefer a higher position.
Seat Belt Pretensioners The seat belts for both front seating positions ar e equipped with pretensioning devices that ar e designed to remove slack fr om the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision.
NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or ST ART position. DaimlerChrysler does not r ecom- mend deactivating BeltAlert t . 1. W ith all doors closed and the ignition switch in any position except ON or ST ART , buckle the driver’s seat belt.
Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender . This extender should be used only if the existing belt is not long enough.
window . If the vehicle is equipped with SABIC air bags, they are located above the side windows and their covers are also labeled: SRS AIRBAG. NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment.
The first stage inflator is triggered immediately during an impact that requir es airbag deployment. The timing of the second stage determines whether the output force is low , medium, or high. If a low output is sufficient to meet the need, the second stage is expended later in the crash event.
When the airbag deploys, it opens the seam between the front and side of the seat’s trim cover . Each airbag deploys independently , that is a left side impact deploys the left airbag only and a right-side impact deploys only the right airbag. W ARNING! • Do not put anything on or around the airbag covers or attempt to open them manually .
Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC Airbags offer side-impact and vehicle r ollover protection to fr ont and rear seat outboard occupants in addition to that provided by the body str ucture.
moderate to severe side collisions. In certain types of collisions, both the front and side airbags may be trig- gered. However , even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you pr operly .
4. If your vehicle has side airbags, do not lean against the door , airbags will inflate forcefully into the space between you and the door . 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center .
impact sensors signals, a central electronic ORC deploys the front airbags, side inflatable airbag curtains, side seat thorax airbags, and front seat belt pr etensioners as re- quired for each type of impact. The ORC monitors the readiness of the electr onic parts of the system whenever the ignition switch is in the ST ART or ON position.
Front and Side Impact Sensors Impact Sensors trigger airbag deployment in front and side impacts, and aid the ORC in determining appropri- ate response to impact events. Additional sensors in the ORC determine the level of airbag deployment and provide verification.
• T urns on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • Unlocks the doors automatically .
irritation, move to fresh air . If the irritation continues, see your doctor . If these particles settle on your clothing, follow the garment manufacturer’s instr uc- tions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed.
W ARNING! Do not attempt to modify any part of your advanced airbag system. The airbag may inflate accidentally or may not function properly if modifications are made.
located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good. Event Data Recorder (EDR) In the event of an accident, your vehicle is design.
accessing the electronic data stor ed, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant). A copy of the data will be provided to the custodial entity upon r equest.
• Engine control status (including engine speed) • T ransmission gear selection • Cruise contr ol status • T raction/stability control status • T ire pr essure monitoring system status – i.
Child Restraints Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces r equire that small children ride in pr oper restraint systems. This is the law , and you can be prosecuted for ignoring it.
• Safety experts recommend that childr en ride rearwar d-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). T wo types of child restraints can be used r earward-facing: infant carriers and 9 convertible 9 child seats.
Older Children and Child Restraints Children who weigh mor e than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing dir ection are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year .
• If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. If this doesn’t help, move the child to the center rear seating position and use the lap belt. Never allow a child to put the shoulder belt under an arm or behind their back.
Here are some tips on getting the most out of your child restraint: • Before buying any r estraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. W e also recommend that you make sure that you can install the child restraint in the vehicle where you will use it, befor e you buy it.
• Buckle the child into the seat according to the child restraint manufactur er’s directions. • When your child restraint is not in use, secur e it in the vehicle with the seat belt or remove it fr om the vehicle. Don’t leave it loose in the vehicle.
When using the tether anchorages in the center position on third r ow fold-in-floor seating, ensure that the strap is routed underneath the top of the seatback and the head restraint. W ARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
Because the lower anchorages are to be intr oduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor - ages will continue to have features for installation in vehicles using the lap or lap/shoulder belt.
Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system. W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint.
This vehicle is equipped with a child restraint tether anchor located on the lower rear of the fr ont passenger seat. Use this tether anchor to secure only forward facing child restraints equipped with an upper tether strap.
VEHICLE EQUIPPED WITH THE REAR SEA T DE- LETE FEA TURE (Commercial V ehicles Only). • The forward-facing child seat is for childr en from about 20 to 40 lbs (9 to 18 kg), and more than one year old.
NOTE: Ensure that the child r estraint tether strap is centered between the headr est supports underneath the head rest. 4. Using the hook attached to the child restraint tether strap, attach the child restraint tether strap to the metal anchor on the lower rear of the fr ont passenger seat.
ENGINE BREAK-IN RECOMMENDA TIONS A long break-in period is not r equired for the engine in your vehicle. Drive moderately during the first 300 mi (500 km).
Airbag Light The light should come on and remain on for four seconds as a bulb check when the ignition switch is first turned ON. If the LED is not lit during starting and/or the light stays on or comes ON while driving, have the system checked by an authorized dealer .
Exhaust Gas W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS m Mirrors .............................. 1 0 0 ▫ Manual Rear V iew Day/Night Mirror — If Equipped ......................... 1 0 0 ▫ Exterior Mirrors ...................... 1 0 2 m Hands-Free Communication (UConnect t )— If Equipped .
▫ Setting Memory Positions And Linking RKE T ransmitter T o Memory ................. 1 5 6 m T o Open And Close The Hood ............. 1 5 8 ▫ Hood Safety Switch — If Equipped ........ 1 5 9 m Lights ............................... 1 6 0 ▫ Interior Lighting .
▫ Power Inverter — If Equipped ............ 1 9 6 ▫ Electrical Outlet Use W ith Engine Off ....... 1 9 8 m Sun Screens— If Equipped ................ 1 9 8 m Cup Holders And Convenience T ray Drawer . . . 200 ▫ Instrument Panel Cup Holders ..
MIRRORS Manual Rear View Day/Night Mirror — If Equipped Adjust the mirror to center on the view thr ough the rear window . A two point pivot system allows for horizontal and vertical adjustment of the mirror . Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle).
CAUTION! T o avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror . Apply the solution onto a clean cloth and wipe the mirror clean. Illuminated V anity Mirrors — If Equipped An illuminated vanity mirror is on the sun visor .
EXTERIOR MIRRORS Side V iew Mirrors T o receive maximum benefit, adjust the outside mirr or(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror . W ARNING! V ehicles and other objects seen in a outside convex mirrors will look smaller and farther away than they really are.
Both mirrors will always move together and will fold anytime the button is pressed. The ignition switch does not have to be in the ON position. Power Remote Side V iew Mirrors — If Equipped Use the mirror select switch located on the driver’s door trim panel, to adjust the view obtained in the outside mirrors.
Select a mirror and pr ess one of the four arrows for the direction you want the mirr or to move. Driver’s power mirror pr eselected positions can be con- trolled by the optional Driver Memory Seat Featur e. Refer to “Driver Memory Seat — If Equipped” in Section 3 of this manual.
UConnect t allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The UConnect t phonebook enables you to store up to 32 names, with four numbers per name.
The UConnect t system can be used with any Hands-Free Profile certified Bluetooth t cellular phone. See the UConnect t website for supported phones. If your cellu- lar phone supports a differ ent profile (e.g., Headset Profile) you may not be able to use any UConnect t features.
example, you can use the combined form voice com- mand 9 Phonebook New Entry , 9 or you can break the combined form command into two voice commands: 9 Phonebook 9 and 9 New Entry . 9 Please remember , the UConnect t system works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.
• When prompted, after the beep, say 9 Pair a Phone 9 and follow the audible prompts. • Y ou will be asked to say a four-digit Personal Identi- fication Number (PIN), which you will later need to enter into your cellular phone. Y ou can enter any four-digit PIN.
user from dialing an invalid combination of numbers. For example, in the U.S., 234-567-890 is nine digits long, which is not a valid U.S. phone number - the closest valid phone number has 10 digits. • The UConnect t system will confirm the phone num- ber and then dial.
• When prompted, say the name of the new entry . Use of long names helps the voice recognition and it is recommended. For example, say 9 Robert Smith 9 or 9 Robert 9 instead of 9 Bob. 9 • When prompted, enter the number designation (e.g., 9 Home, 99 W ork, 99 Mobile, 9 or 9 Pager 9 ).
and you may see a message on the phone display that the Bluetooth t link is busy . In this case, the user must first disconnect or drop the Bluetooth t connection to the UConnect t system, and then send the address book entry via Bluetooth t .
Delete Entries in the UConnect t Phonebook NOTE: Editing phonebook entries is recommended when the vehicle is not in motion. • Press the PHONE button to begin.
List All Names in the UConnect t Phonebook • Press the PHONE button to begin. • After the 9 Ready 9 prompt and the following beep, say 9 Phonebook List Names.
Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in pr ogress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the PHONE button to place the curr ent call on hold and answer the incoming call.
Three-W ay Calling T o initiate three-way calling, pr ess the “V oice Recogni- tion” button while a call is in progr ess, and make a second phone call, as described under 9 Making a Second Call While Current Call in Pr ogress.
• After the ignition key is switched to OFF , a call can continue on the UConnect t system for a certain dura- tion, after which the call is automatically transferred from the UConnect t system to the mobile phone. • An active call is automatically transferred to the mobile phone after the ignition key is switched to OFF .
• After the 9 Ready 9 prompt and the following beep, say 9 Emergency 9 and the UConnect t system will instruct the paired cellular phone to call the emer gency num- ber . This feature is supported in the U.S., Canada, and Mexico. NOTE: The emergency number dialed is based on the country where the vehicle is pur chased (91 1 for the U.
certain companies, which time out a little too soon to work properly with the UConnect t system. V oice Mail Calling T o learn how to access your voice mail, refer to 9 W orking with Automated Systems.
NOTE: • Y ou may not hear all of the tones due to cellular phone network configurations; this is normal. • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature.
dialing a number with your paired Bluetooth t cellular phone, the audio will be played through your vehicle’s audio system. The UConnect t system will work the same as if you dial the number using voice recognition.
Connect or Disconnect Link Between the UConnect t System and Cellular Phone Y our cellular phone can be paired with many dif ferent electronic devices, but can only be actively 9 connected 9 with one electronic device at a time.
• The selected phone will be used for the next phone call. If the selected phone is not available, the UConnect t system will return to using the highest priority phone present in or near (appr oximately within 30 ft [9 m]) the vehicle. Delete UConnect t Paired Cellular Phones • Press the PHONE button to begin.
Repeat the words and phrases when pr ompted by the UConnect t system. For best results, the V oice T raining session should be completed when the vehicle is parked with the engine running, all windows closed, and the blower fan switched OFF . This procedur e may be repeated with a new user .
• When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say 9 Send. 9 • Storing names in the phonebook when the vehicle is not in motion is recommended. • It is not recommended to stor e similar sounding names in the UConnect t phonebook.
• Echo at the far end can sometimes be reduced by lowering the in-vehicle audio volume. • In a convertible vehicle, system performance may be compromised with the convertible top down. Bluetooth t Communication Link Cellular phones have been found to lose connection to the UConnect t system.
126 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 127 3.
128 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
V oice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all V oice Commands Primary Alternate(s) call cancel confirmation prompt.
V oice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous recor d again redial V oic.
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference r eceived, including interference that may cause undesir ed op- eration.
Manual Front And Second Row Seat Adjuster The adjusting bar is located under the front of the seat. Pull the bar up and move the seat to the desired position. Release the bar to lock the seat into position. Using body pressur e, move forward and rearwar d on the seat to be sure the seat adjusters have latched.
8–W ay Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the outboard side of the seat. The fr ont switch controls up/down, forward/r earward, and tilt adjustment. The rear switch contr ols the seatback recline adjustment.
Adjustable Head Restraints Head restraints can r educe the risk of whiplash injury in the event of impact from the r ear . Pull up or push down on the head restraint cushion so that the upper edge is as high as practical. T o raise the head restraint, pull up on the head restraint.
Heated Seats — If Equipped This feature heats the fr ont driver and passenger seats. The controls for fr ont heated seats are located on the center instrument panel ar ea.
W ARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater . It may cause burns even at low temperatures, especially if used for long periods of time.
W ARNING! DO NOT ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.
Stow ’n Go Seating — If Equipped On vehicles equipped with Stow ’n Go seating, the second and third r ow seats may be folded into the floor for convenient storage. T o Fold Second Row Seats 1. Move the front seat fully forwar d. 2. Lower the head restraints and raise the armr ests on the second row seat.
4. Pull up on the seatback recliner lever located on the outboard side of the seat and fold the seatback down. T o assure the seatback is latched in the folded position, additional downward pr essure on the seatback may be requir ed when folding.
5. Pull rearwar d on the release strap located at the rear of the seat and tumble the seat forward into the storage bin. 6. Close the storage bin cover and slide the storage bin locking mechanism to the locked position.
T o Unfold Second Row Seats 1. Slide the storage bin locking mechanism to the 9 un- locked 9 position and then pull up on the storage bin latch to open the cover . 2. Pull up on the handle to lift the seat out of the storage bin and push the seat rearwar d to latch the seat anchors.
3. Pull up on the seatback recliner lever located on the outboard side of the seat, to r eturn the seatback to its full upright position. 4. Close the storage bin cover and adjust the head restraint to the desir ed position.
The power recline featur e, located on the side of the seat cushion, adjusts the seatback angle forward/r earward for occupant comfort Remote Third Row Power Seat Switch— If Equipped A One-T ouch Third Row Power Folding Seat switch is located in the left rear trim panel as part of a switch-bank.
The rear switch bank allows multiple power folding and unfolding positions for the third r ow seats. Left and right third r ow seats can be folded individually or together .
NOTE: The Third Row Power Seat system includes obstacle detection for safe operation. When the system detects an obstacle, the motors will stop and reverse the motion for a brief period. Should this occur , remove the obstacle and repr ess the button again, for the desired position.
T o Unfold Third Row Seats 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch. 2. Pull release strap marked “1” to unlock the r ecliner . 3. Pulling strap “3” releases the seatback to r eturn to its full upright position.
W ARNING! T o avoid serious injury or death, NEVER operate the vehicle with occupants in the third row seat while in the tailgate mode. Easy Access Seating The second row Stow ’n Go seats can be tilted forwar d for easy access to the third r ow seat or rear cargo ar ea.
Swivel ’n Go Premium Seating — If Equipped Premium second r ow Swivel ’n Go Seating features include: • A table that installs between the second and third row seats.
T o swivel the seat: Pull the lower handle on the outboard side of the seat and push the side of the seatback to begin rotation. Once the seat begins to r otate, the handle may be released. The seat locks in position once r eaching the forward or r earward positions only .
Removing Swivel ’n Go Premium Seating — If Equipped 1. Remove any obstructions fr om the floor behind the seat, and stow the Third Row Seat. 2. Pull up on the release bar located at the bottom fr ont edge of the swivel seat. 3. From behind the seat, lift up on the r ear of the seat cushion while pulling the seat in a rearwar d direction.
Swivel ’n Go Premium Seating T able — If Equipped The Swivel ’n Go Seating T able consists of an easily assembled post and top. The table and leg are stor ed beneath the floor when not in use. T o install the table follow these steps: 1. Swivel the second row seats so they ar e facing the rear .
2. Open the floor storage cover in front of the second r ow seats. 3. Remove the pole and table top by loosening the hook and loop straps. 4. Insert pole into base by aligning the lock button into notch of the base.
5. T wist the pole in a clockwise rotation until it stops. Note: Y ou will hear an audible “click” when the lock button engages the base. 6. Place the table top over the installed pole aligning with the mating feature of the underside of the table top.
T o separate the table top from the pole, follow these steps: 1. Locate the release latch on the underside of the table top. 2. Pull horizontally on the latch to activate the release from the pole. 3. While pulling on the latch, pull upward to r emove the table top from the pole.
Plastic Grocery Bag Retainer Hooks Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all r ear seats and some front seats.
Setting Memory Positions And Linking RKE T ransmitter T o Memory NOTE: Each time the SET(S) button and a numbered button (1 or 2) are pr essed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key and turn the ignition switch to the ON position.
10. Insert the ignition key and turn the ignition switch to the ON position. 1 1. Select 9 Remote Linked to Memory 9 in the Electronic V ehicle Information Center (EVIC) and enter 9 Ye s 9 or select 9 No 9 from the EVIC and enter 9 Ye s 9 .
2. Press and r elease Memory Button 1. The system will recall any memory settings stor ed in position 1. W ait for the system to complete the memory recall befor e continu- ing to step 3. 3. Press and r elease the memory SET(S) button located on the driver’s door .
Use the hood prop r od to secure the hood in the open position. T o prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 12 inches (30 cm) and then drop it. This should secur e both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
If the vehicle is equipped with the Compass Mini-T rip Computer (CMTC) and the hood is not latched, a “hood” will be displayed in the PRNDL/Odometer window of the instrument cluster .
The interior lights will automatically turn off in about 10 minutes for the first activation and 90 seconds every activation thereafter until the engine is started, if one of the following occur: • .
Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent. This feature brightens the odometer , radio and overhead dis- plays when the park lights or head- lights are on.
Daytime Running Lights (Canada/Fleet V ehicles Only) The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except P ARK. This provides a constant lights on condi- tion until the ignition is turned OFF .
NOTE: The engine must be running befor e the head- lights will come on in the Automatic mode. Headlights On with W ipers — If Equipped If your vehicle is equipped with Automatic Headlights it also has this customer programmable featur e.
If the headlights are turned of f before the ignition, they will turn off in the normal manner . NOTE: The headlights must be turned off within 45 seconds of turning the ignition OFF to activate this feature.
Battery Protection This feature pr ovides battery protection to avoid wearing down the battery if the headlights, park lights, or front fog lights are left on for extended periods of time when the ignition switch is in the LOCK position.
If either indicator flashes at a rapid rate, check for a defective outside turn signal light bulb. If one of the indicators fails to light when the lever is moved, it would suggest that the indicator light is defective. Y ou may manually signal a lane change by moving the lever partially up or down.
W indshield Wiper and W asher Functions The wipers and washers are operated by a switch within the multifunction lever . Rotate the end of the lever to select the desired wiper speed. NOTE: Always remove any buildup of snow that pr e- vents the windshield wiper blades from r eturning to the off position.
1. Multifunction Lever — Mist, Front W iper and W asher Press the end of the multifunction lever inwar d to the first detent and release to clear the windshield.
the rotary ring fully forwar d and the washers will spray until the ring is released, and then r esume the intermit- tent interval. NOTE: Rear window wipers function in the intermittent wiper speed only .
TIL T STEERING COLUMN — IF EQUIPPED T o tilt the column, pull the small lever downward (located on the steering column and below the steering wheel) to the open position. Y ou may then position the steering wheel up or down, as desired. Pull the small lever upward to the closed position to lock the steering wheel firmly in place.
The Rear Park Assist System will remember the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the RUN/ON position. The Rear Park Assist System can be active only when the transaxle gear selector lever is in REVERSE.
When the ignition switch is turned to the RUN/ON position, the warning display will turn on all of its LEDs for about one second. Each side of the warning display has six yellow and two red LED lights, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle.
P ARK ASSIST W ARNING DISPLA Y DIST ANCES DISPLA Y LED OBST ACLE DIST ANCE FROM: REAR CENTER AUDIBLE SIGNAL REAR CORNERS REAR CENTER 1st LED 78.7 in (200 cm) Y ellow Y es, Half Second 2nd LED 51.1 in (130 cm) Y ellow None 3rd LED 45.2 in (1 15 cm) Y ellow None 4th LED 31.
W ARNING! Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.
NOTE: • Ensure that the r ear bumper is free of dirt and debris to keep the system operating properly . • Jackhammers, large tr ucks, and other vibrations could affect the performance of the system.
If ( SER VICE P ARK ASSIST SYSTEM ( appears in the Electronic V ehicle Information Center (EVIC), after mak- ing sure the r ear bumper is clean, please see your authorized dealer . Should this wrench symbol display with the letter P next to it, your Park Sense System needs servicing.
Press the button forwar d to move the pedals forward (toward the fr ont of the vehicle). Press the button r earward to move the pedals rearwar d (toward the driver). • The pedals can be adjusted with the ignition OFF . • The pedals can be adjusted while driving.
ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h). Activating Electronic Speed Control Push the ON/OFF but.
Setting Electronic Speed Control at a Desired Speed When the vehicle has reached the desir ed speed, press the SET lever downward and then r elease. Lift your foot off the accelerator and the vehicle will operate at the selected speed.
NOTE: The Electronic Speed Contr ol system has been designed to shut down if multiple speed control switch functions are operated simultaneously in or der to ensure proper operation. If this occurs, the system can be reactivated by pushing the speed contr ol switch ON/ OFF button and resetting the desir ed vehicle SET speed.
OVERHEAD CONSOLES Front Overhead Console — If Equipped T wo versions of the overhead console ar e available. The base front over head console models feature fixed incan- descent courtesy/reading lights, flip-down sunglass stor - age and conversation mirror .
Courtesy/Interior Lighting At the forward end of the console ar e two courtesy lights (standard dome light has two buttons). The lights turn on when a front door , a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry , the lights will also turn on when the unlock button on the transmitter is pressed.
Rear Overhead Consoles — If Equipped The rear over head storage system is available in two versions: with or without sunroof. An additional LED at the front of the r ear console shines down on the second row footwell ar ea while in courtesy mode, for added convenience.
Rear Courtesy/Reading Lights — If Equipped The overhead console had two sets of courtesy lights. The lights turn on when a front door , a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry , the lights will also turn on when the unlock button on the transmitter is pressed.
The HomeLink t buttons that are located in the headliner or sun visor designate the three dif ferent HomeLink t channels. NOTE: HomeLink t is disabled when the V ehicle Secu- rity Alarm is active. W ARNING! Y our motorized door or gate will open and close while you are training the Universal T ransceiver .
W ARNING! V ehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run your vehicle in the garage while training the transceiver . Exhaust gas can cause seri- ous injury or death. PROGRAMMING HOMELINK T Before Y ou Begin If you have not trained any of the HomeLink t buttons, erase all channels before you begin training.
W atch for the HomeLink t indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds, or longer in rare cases. The garage door may open and close while you train.
6. Firmly press and release the “Learn” or “T raining” button. The name and color of the button may vary by manufacturer . NOTE: There ar e 30 seconds in which to initiate the next step after the “Learn” button has been pressed.
Using HomeLink t T o operate, simply press and r elease the programmed HomeLink t button. Activation will now occur for the trained device (i.e., garage door opener , gate operator , security system, entry door lock, home/office lighting, etc. The hand-held transmitter of the device may also be used at any time.
has successfully accepted the frequency signal. The indicator light will flash slowly and then rapidly when fully trained. If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Pr ogramming HomeLink t ,” earlier in this section.
2. This device must accept any interference that may be received including interfer ence that may cause undesired operation. NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly appr oved by the party responsible for compli- ance could void the user ’s authority to operate the device.
Closing the Sunroof Manually T o close the sunroof fr om an open or vent position, press and hold the switch forward. The sunr oof will close fully and stop automatically . Release the switch to stop sun- roof travel at any point. Sunroof Sunshade Operation The sunroof sunshade can be opened manually .
Express-V ent Press and r elease the 9 V 9 button, and the sunroof will automatically open to the vent position. This is called Express-V ent. Express-Close Press the switch forwar d and release, and the sunroof will close automatically from any position.
open or partially open positions. This is a normal occur- rence and can be minimized. If the buf feting occurs with the rear windows open, open the fr ont and rear windows together to minimize the buffeting. If the buf feting occurs with the sunroof open, adjust the sunr oof opening to minimize the buffeting or open any window .
when the overload is removed. The cir cuit breaker also supplies power to the outlet in the removable floor console, when in the front position. Refer to section 3 “Removable Floor Console” in this manual. A third outlet is located on the driver’s side, just to the rear of the sliding door and is also contr olled by the ignition switch.
NOTE: • When the Inverter Switch is pressed, ther e will be a delay of approximately one second befor e the inverter status indicator turns ON. The status indicator of the AC power inverter indicates whether the inverter is producing AC power . • Due to built-in overload protection the inverter will shut down if the power rating is exceeded.
ELECTRICAL OUTLET USE WITH ENGINE OFF CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e., cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Gently pull up on the tab to raise the sun screen. Continue pulling the sun screen until the tab is near the top of the window . Once the screen is completely to the top of the window , extend the top bar of the sun screen over the two hooks attached to the top of the window .
CUP HOLDERS AND CONVENIENCE TRA Y DRA WER There ar e nine cup holders in the interior . T wo cup holders in the center front instr ument panel, four in the floor consoles and three mor e are located in the third r ow quarter trim panel. All liners are r emovable for cleaning.
Interior Bottle Holders There ar e four bottle holders located in the interior . One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel. Each holder accommo- dates up to 20 oz.
• The cup holder/tray top is removable to access a lar ge storage bin. • The Basic Console is removable fr om the vehicle for additional floor space by removing the cap at the console base. T o Remove The Basic Floor Console • Remove the front anchor cup plug and clip.
• Slide the console base forward while lifting slightly to clear the rear load floor hook. • Remove the console. T o Reinstall The Basic Floor Console • Position the console at a slight angle (front slightly higher than the rear . • Slide the console rearwar d into the floor bracket/ hook.
• T op T ray Storage • Upper Storage Bin can hold nine regular or 18 thin CD’s or other items • Large Console Center Storage will stor e headphones for the available rear DVD entertainment system or other items • 12–V olt DC Power Outlet provides continuous power inside the console for cell phones or other electronics.
The top and center console sections slide forward and rearwar d to provide added user comfort. Four cup hold- ers, each of which can accommodate large sized beverage containers. A one-piece cup holder insert for both cavities can easily be removed for cleaning.
Position 2 shows the raised storage tray revealing a lar ge storage area below . Dual Storage Bins Position 3 shows the top portion of the console in a rearwar d position. This is accomplished by lifting the upper most latch at the front of the console.
T o Remove The Premium Floor Console • Pull up on the bottom release handle in the fr ont of the console • Lift the rear of the console up several inches • Pull rearwar d to disengage from floor.
W ARNING! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched. STORAGE Glove Compartments There ar e both upper and lower glove compartments.
Lower Glove Compartment T o open the lower compartment (1) pull out on the release handle (2). The lower compartment handle is also equipped with a lock. Door T rim Panel Storage Front Door Storage Both interior front door panels have multiple pockets for storage.
Sliding Side Door Bottle Holder Both sliding doors have a bottle holder molded right into the trim. Second Row Floor Storage Bins — If Equipped The Second Row Seat Storage Bins are located on the floor in front of the second r ow seats. The area below the floor covers can be used for storage when the second row seat is in the upright position.
Pull up on the storage bin latch to open the cover . Slide the storage bin locking mechanism to the 9 unlocked 9 position to allow greater access to the storage bin. CAUTION! The storage bin cover must lay flat and be locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover .
T o remove the console use the following pr ocedure: 1. Open the console lid and remove the storage tray . 2. Pull up on the release handle located inside the floor console, and slide the console rearwar d to disengage from the floor . 3. Remove the floor console.
W ARNING! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched. Rear Compartment Storage Y our vehicle is equipped with open storage areas located in each rear trim panel.
Coat Hooks Coat hooks are located along the headliner for the second and third r ow seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage fr om the vehicle.
ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails ar e designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Distribute cargo weight evenly on the r oof rack crossbars.
CAUTION! • Crossbars should remain equally spaced or paral- lel at any luggage rack position for proper func- tion. Noncompliance could result in damage to the luggage rack, cargo and/or vehicle. • T o avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg).
W ARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.
LOAD-LEVELING SYSTEM — IF EQUIPPED The automatic load-leveling system will provide a level riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the corr ect height.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS m Instrument Panels And Controls ............ 2 2 3 m Base Instrument Cluster .................. 2 2 4 m Premium Instr ument Cluster ............... 2 2 5 m Instrument Cluster Descriptions ............ 2 2 6 m Compass Mini-T rip Computer (CMTC) — If Equipped .
m Sales Code REQ — AM/FM Stereo Radio And 6–Disc CD/DVD Changer (MP3/WMA AUX Jack) .................. 2 5 2 ▫ Operating Instructions - Radio Mode ....... 2 5 2 ▫ Operation Instructions - (Disc Mode For CD And MP3/WMA Audio Play , DVD-V ideo) .
m Sales Code RER — Multimedia System — If Equipped ........................... 2 8 3 ▫ Operating Instructions — Satellite Radio ..... 2 8 4 ▫ Operating Instructions — Hands-Fr ee Communication (UConnect t ) (If Equipped) . . . 284 ▫ Clock Setting Procedur e.
m Radio Operation And Cellular Phones ........ 2 9 9 m Remote Sound System Controls — If Equipped . . 299 ▫ Radio Operation ...................... 2 9 9 ▫ CD Player .......................... 3 0 0 m CD/DVD Maintenance ................... 3 0 0 m Climate Controls .
INSTRUMENT P ANELS AND CONTROLS 1 - Air V ents 6 - Upper Glove Compartment 1 1 - Storage Bin 16 - Head Light Switch 2 - Instrument Cluster 7 - Lower Glove Compartment 12 - Power Supply 12V 17 - Power .
BASE INSTRUMENT CLUSTER 224 UNDERST ANDING YOUR INSTRUMENT P ANEL.
PREMIUM INSTRUMENT CLUSTER UNDERST ANDING YOUR INSTRUMENT P ANEL 225 4.
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Fuel Door Reminder The arrow in this symbol is a r eminder that the Fuel Filler Door is located on the left side of the vehicle.
W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call an authorized dealer if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual.
If the ABS light is on, the brake system should be serviced as soon as possible to restor e the benefits of Anti-Lock brakes. If the ABS light does not turn on when the Ignition switch is turned to the ON position, have the light inspected by an authorized dealer .
Brake W arning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. The operation of the Brake W arning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approxi- mately two seconds.
replacement, be sur e to keep a record of the r eading before and after the service so that the corr ect mileage can be determined. The trip odometer shows individual trip mileage. T o switch from odometer to trip odometer , press the T rip Odometer button.
seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle-based, which means the engine oil change interval may fluctuate dependent upon your personal driving style.
15. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors engine and automatic transmission control systems. The light will illu- minate when the key is in the ON position before engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked pr omptly .
requir e towing. The light will come on when the ignition is first turned ON and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer . 18. Oil Pressur e W arning Light This light shows low engine oil pressur e.
during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible. 23. V oltage Light This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started.
reduces fuel ef ficiency and tire tread life, and may af fect the vehicle’s handling and stopping ability . NOTE: Please note that the TPMS is not a substitute for proper tir e maintenance, and it i.
For additional information on TPMS, refer to Section 5 — Starting and Operating, “T ire Pr essure Monitoring Sys- tem” of this manual. For additional information on T ire Pr essures, refer to Section 5 — Starting and Operating, “T ire Inflation Pressur es” of this manual.
Electronic V ehicle Information Center (EVIC) Display — If Equipped The Electronic V ehicle Information Center (EVIC) fea- tures a driver -interactive display that is located in the lower half of the speedometer . Oil Change Required Y our vehicle is equipped with an engine oil change indicator system.
COMP ASS MINI-TRIP COMPUTER (CMTC) — IF EQUIPPED NOTE: The compass on your vehicle is self-calibrating, eliminating the need to manually calibrate the compass. The Compass Mini-T rip Computer features a driver - interactive display (displays information on outside tem- perature, compass dir ection, and trip information).
T o reset the display shown, turn the ignition switch to the ON position, then press and hold the r eset button for approximately two seconds. When the appropriate conditions exist, the following odometer messages will display: NE ....... Eight-point compass headings are display ed (N, S, E, W , NE, NW , SE, SW) 14°F .
Compass/T emperature Display Compass V ariance Compass V ariance is the differ ence between magnetic North and Geographic North. In some areas of the country , the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
2. Press and hold (appr oximately 10 seconds) the CMTC reset button until the curr ent variance zone number is displayed. 3. Release the CMTC reset button, then pr ess and hold again (approximately 10 seconds), until the dir ection is displayed with the CAL indicator on continuously in the display .
• Compass display • Outside temperature display • T rip computer functions • Audio Modes display EVIC Menu / Step Control Button as it appears on the left side of the steering column. Press and r elease the MENU button and the mode displayed will change between Compass/T emperature, T rip, System Status, and Personal Settings.
EVIC Displays When the appropriate conditions exist, the EVIC displays the following messages: • Door(s) Ajar (with a single chime if vehicle is in motion) • Liftgate Ajar (chime will sound when vehicle starts moving) • Hood Ajar (If equipped with hood switch) • Check TPM System.
Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. T o turn off the message temporarily , press and release the Menu button. T o reset the oil change indicator system (after performing the scheduled maintenance) refer to the following pr ocedure.
Distance T o Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy , according to the current fuel tank level.
COMP ASS DISPLA Y The compass readings indicate the dir ection the vehicle is facing. Press and r elease the compass button to display one of eight com- pass readings and the outside temperatur e. Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to manually reset the compass.
Compass V ariance Compass V ariance is the differ ence between magnetic North and Geographic North. In some areas of the country , the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
1. T urn the ignition switch ON. 2. Press and hold the compass button for appr oximately two seconds. 3. Press the STEP button until “Compass V ariance” mes- sage and the last variance zone number displays in the EVIC. 4. Press and r elease STEP button until the proper vari- ance zone is selected according to the map.
Unlock Doors Automatically on Exit When ON is selected, all doors will unlock when the vehicle is stopped and the transmission is in the P ARK or NEUTRAL position and the driver’s door is opened. T o make your selection, press and r elease the RESET button until ON or OFF appears.
SELECT button until YES (Y) or NO (N) appears. Refer to “Lights/SmartBeams — If Equipped” in Section 3 of this manual for more information. Headlights On with W ipers (A vailable with Auto Headl.
Rear Park Assist System — If Equipped When ENABLE is selected, the Rear Park Assist System is activated. When DISABLE is selected, the System is deactivated and, the instrument cluster will display the 9 P ARK ASSIST DISABLED 9 message.
FM Reception Because FM transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the r eception relatively clear , which is the major feature of FM radio.
When the audio system is turned on, the sound will be set at the same volume level as last played. SEEK Buttons Press and r elease the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down.
TIME Button Press the TIME button and the time of day will display . In AM or FM mode, pressing the TIME button will switch between the time and frequency displays. Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side T une/Scroll control knob.
Setting the T one, Balance, and Fade Push the rotary T une/Scroll control knob and BASS will display . T urn the T une/Scroll control knob to the right or left to increase or decr ease the bass tones. Push the rotary T une/Scroll control knob a second time and MID will display .
Program T ype 16-Digit Character Display No program type or undefined None Adult Hits Adlt Hit Classical Classicl Classic Rock Cls Rock College College Country Country Foreign Language Language Inform.
station with the same selected Music T ype name. The Music T ype function only operates when in the FM mode. If a preset button is activated while in the Music T ype (Program T ype) mode, the Music T ype mode will be exited and the radio will tune to the preset station.
NOTE: These selections can only be made while playing a DVD. • VES t Power - Allows you to turn VES t on and off (if equipped). • VES t Lock - Locks out rear VES t r emote controls (if equipped).
Subtitle Language — If Equipped Selecting this item allows you to choose a default subtitle language (effective only if the language is supported by the disc).
SET Button — T o Set the Pushbutton Memory When you are r eceiving a station that you wish to commit to pushbutton memory , press the SET button. The symbol SET 1 will now show in the display window . Select the button (1-6) you wish to lock onto this station and press and r elease that button.
CAUTION! The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate “Disc Hot” and shut off until a safe temperature is reached. This shutdown is necessary to protect the optics of the DVD player and other radio internal components.
Press and hold the EJECT button for five seconds and all CDs will be ejected from the radio. The disc can be ejected with the radio and ignition OFF . SEEK Button (CD MODE) Press the right SEEK button for the next selection on the CD.
Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs r ecorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor - mally .
When using the MP3/WMA encoder to compress audio data to an MP3/WMA file, the bit rate and sampling frequencies in the following table ar e supported. In addition, V ariable Bit Rates (VBR) are also supported. The majority of MP3/WMA files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates.
Loading times for playback of MP3/WMA files may be affected by the following: • Media - CD-R W media may take longer to load than CD-R media • Medium formats - Multisession discs may take longer t.
Press and hold the INFO button again for thr ee seconds to return to 9 elapsed time 9 display . Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows th.
Operating Instructions — V oice Recognition System (VR) (If Equipped) For the radio, refer to “V oice Recognition System (VR)” in Section 3. For UConnect t “V oice Recognition System (VR)” refer to “Hands-Free Communication (UConnect t )” in Section 3.
SALES CODE RES — AM/FM STEREO RADIO WITH CD PLA YER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it.
2. Adjust the hours by turning the right side T une/Scroll control knob. 3. After adjusting the hours, press the right side T une/ Scroll contr ol knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side T une/Scroll control knob.
Push the rotary T une/Scroll control knob a second time and MID will display . T urn the T une/Scr oll control knob to the right or left to increase or decr ease the mid-range tones. Push the rotary T une/Scroll control knob a thir d time and TREBLE will display .
Program T ype 16-Digit Character Display Foreign Language Language Information Inform Jazz Jazz News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B.
SETUP Button Pressing the SETUP button allows you to select between the following items: • Set Clock — Pressing the SELECT button will allow you to set the clock. T urn the T une/Scroll contr ol knob to adjust the hours and then press and turn the T une/Scroll contr ol knob to adjust the minutes.
DISC Button Pressing the DISC button will allow you to switch fr om AM/FM modes to Disc modes. Operation Instructions - CD MODE for CD and MP3 Audio Play NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player .
TIME Button Press this button to change the display fr om a large CD playing time display to a small CD playing time display . R W/FF Press the R W button to stop the CD at the beginning of the current CD track/title.
files properly and may be unable to play the file nor - mally . UDF and Apple HFS formats ar e not supported. The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders.
rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Specification Sampling Fre- quency (kHz) Bit Rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio Layer 3 24, 22.
LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the T une/Scroll contr ol knob.
TIME Button (Auxiliary Mode) Press this button to change the display to time of day . The time of day will display for five seconds (when ignition is OFF). Operating Instructions - Hands-Free Phone (UConnect t ) (If Equipped) Refer to “Hands-Free Communication (UConnect t )” in Section 3.
through the system’s wir eless headphones. This means rear seat passengers can watch a DVD on the optional rear seat entertainment system, while the driver and front-seat passenger listen to the radio.
3. T o move the hour forward, touch the scr een where the word “Hour” with the arr ow pointing upward is dis- played. T o move the hour backward, touch the scr een where the wor d “Hour” with the arrow pointing down- ward is displayed.
T ouch the screen wher e the words “Show T ime if Radio is Off” ar e displayed to change the current setting. Changing the T ime Zone 1. T urn on the multimedia system. 2. T ouch the screen wher e the time is displayed. The clock setting menu will appear on the screen.
The satellite navigation capability combines a Global- Positioning System (GPS)-based navigation system with an integrated color screen to pr ovide maps, turn identi- fication, selection menus, and instructions for selecting a variety of destinations and routes.
Clock Setting Procedure The GPS receiver in this system is synchr onized to the time data being transmitted by the GPS satellites. The satellites’ clock is Greenwich Mean T ime (GMT). This is the worldwide standard for time. This makes the sys- tem’s clock very accurate once the appropriate time zone and daylight savings information is set.
3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.” T ouch the screen wher e the words “Daylight Savings” are dis- played to change the current setting.
2. T ouch the screen wher e the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Show T ime if Radio is Off.” T ouch the screen wher e the words “Show T ime if Radio is Off” ar e displayed to change the current setting.
T o access the ESN/SID, refer to the following steps: ESN/SID Access W ith REQ/RES Radios W ith the ignition switch in the ON/RUN or ACC posi- tion and the radio on, press the SETUP button and scroll using the T une/Scroll contr ol knob until Sirius ID is selected.
Reception Quality Satellite reception may be interr upted due to one of the following reasons: • The vehicle is parked in an undergr ound parking structur e or under a physical obstacle. • Dense tree coverage may interr upt reception in the form of short audio mutes.
additional three seconds will make the radio display the Song T itle all of the time (press and hold again to r eturn to normal display). INFO Button — REU Radio Pressing the INFO button will display information about Artist, Song T itle, and Composer (if available).
Pressing the MUSIC TYPE button again will close the MUSIC TYPE screen. Once closed, seek up, seek down, and scan will no longer be based on your selection. SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number .
Operating Instructions - Hands-Free Phone (If Equipped) Refer to “Hands-Free Communication (UConnect t )” in Section 3. Operating Instructions - Video Entertainment System (VES T ) (If Equipped) Refer to separate “V ideo Entertainment System (VES t ) Guide.
Connecting The iPod T Device Use the optional connection cable to connect an iPod t to the vehicle’s UCI connector (which is located in the glove box or center console on some vehicles.
R W (Rewind) Button Press and hold the R W button to move backward in the current track. Holding the R W button long enough will take you back to the beginning of the current track. Pressing and r eleasing the RW button will go back five seconds of the current track.
SCAN Button Pressing the SCAN button will play the first five seconds of each track in the current list and then forwar d to the next song. T o stop the SCAN mode and start playing the desired track, pr ess the SCAN button again. During the SCAN mode, you can also press the SEEK button to the left or right to go to the previous or next tracks.
Radio Preset Buttons In the List mode, the radio preset buttons ar e used as shortcuts to the following lists on the iPod t device. • 1 – Playlists • 2 – Artists • 3 – Albums • 4 – Gen.
SIRIUS BACKSEA T TV™ — IF EQUIPPED Satellite video uses direct satellite r eceiver broadcasting technology to provide str eaming video coast to coast. The subscription service provider is SIRIUS Satellite Radio. SIRIUS Backseat TV™ offers thr ee video channels for family entertainment, directly fr om its satellites and broadcasting studios.
• Nine differ ent medias to choose from in each screen (AM, FM, Sirius Radio, DVD1, DVD2, Hard Drive Jukebox, AUX in radio, AUX1, AUX2). The LCD screen(s) ar e located in the overhead compart- ment console. NOTE: Refer to your VES t User’s Manual for detailed operating instructions.
RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the cellular phone being ON in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play .
CLIMA TE CONTROLS The Climate Control System allows you to r egulate the temperature, amount, and dir ection of air circulating throughout the vehicle.
Front Blower Control There ar e four blower speeds. Use this control to r egulate the amount of air forced thr ough the system in any mode you select. The blower speed increases as you move the contr ol clockwise from the of f position. T emperature Control Use this control to r egulate the tem- perature of the air inside the passenger compartment.
P ANEL Mode Air is directed thr ough the outlets in the instrument panel. These outlets can be adjusted to direct airflow . BI-LEVEL Mode Air is directed thr ough the panel and floor outlets. NOTE: There is a dif ference in temperature (in any conditions other than full cold or full hot), between the upper and lower outlets for added comfort.
RECIRCULA TION Control Press this button to choose between outside air intake or recir culation of the air inside the vehicle. A lamp will illu- minate when you are in RE- CIRCULA TION mode.
ECONOMY Mode If ECONOMY mode is desir ed, press the A/C button to turn off the indicator light and the A/C compressor . Rotate the temperature contr ol knob to the desired tem- perature. Air Conditioning Operation Push on this button to engage the Air Conditioning.
The Three Zone Basic T emperature Control bottom panel controls r ear Heating, V entilation, and Air Conditioning (HV AC) operations. Three Zone T emperature Control 1 — Left T emp 7 — Right T emp.
The primary control for the r ear blower is on the front climate control unit located on the instr ument panel. The front climate contr ol unit has five positions, off, rear , and a range of blower speeds. Only when the primary control for the r ear blower is in the REAR position do the second seat occupants have control of the r ear blower speed.
Only when the front contr ol for the rear blower is in the RR position do the second seat occupants have control of the rear blower speed. The rear blower contr ol, located in the rear overhead console has an off position and a range of blower speeds.
control is in FLOOR, DEFROST , or MIX modes, airflow will be directed out of the r ear floor outlets. Rear Mode Control FLOOR Mode Air comes from the floor outlets.
The Infrared Thr ee-Zone A TC System automatically maintains the interior comfort level desired by the driver and all passengers. This is accomplished by an infrared sensor , located in the forward overhead console.
Below the automatic control, the system selects the appropriate mode (airflow outlets) and fan speed. Operation of the system is quite simple. 1. Press the AUTO button and the wor d AUTO will illuminate in the front A TC display , along with three temperatures for Driver’s, Passenger , and Rear seats.
NOTE: • It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode and fan speed to pr ovide comfort as quickly as possible. • The temperature can be displayed in U.S. or Metric by selecting the US/M customer programmable featur e.
P ANEL Mode Air comes from the outlets in the instr ument panel. Each of these outlets can be individually adjusted to direct the flow of air . Moving the air vanes of the center outlets down, will close off the airflow fr om the center outlets.
The SNOWFLAKE mode or A/C button allows the operator to manually activate or deactivate the air conditioning system. When in SNOWFLAKE mode the A TC display is on, cool, dehumidified air flows through the air outlets.
The REAR SYSTEM control for the Rear A TC System is on the front A TC control unit located on the instrument panel. Pressing the REAR LOCK button for the Rear A TC System from the fr ont A TC control unit, illuminates a LOCK symbol in the rear display .
Operation of the rear system is quite simple. 1. Press the REAR LOCK button on the fr ont A TC control unit. This turns off the REAR LOCK icon in the r ear temperature knob. 2. Rotate the Rear Blower , Rear T emperature and the Rear Mode Control knobs to suit your comfort needs.
CAUTION! Interior air enters the Rear Automatic T emperature Control System through an intake grille located in the passenger side trim panel behind the third seat. The heater outlets are located in the passenger side trim panel just behind the sliding door .
HEADLINER Mode Air comes from the outlets in the headliner . Each of these outlets can be individually adjusted to direct the flow of air . Moving the air vanes of the outlets to one side will shut off the airflow .
OUTSIDE AIR INT AKE Make sure the air intake, located dir ectly in front of the windshield, is free of obstr uctions such as leaves. Leaves collected in the air intake may reduce airflow and if they enter the plenum they could plug the water drains. In winter months make sure the air intake is clear of ice, slush and snow .
A/C AIR FIL TER — IF EQUIPPED On vehicles equipped with Automatic T emperature Con- trol (A TC), the climate control system filters out dust and pollen from the air .
ST ARTING AND OPERA TING CONTENTS m Starting Procedur es ..................... 3 2 4 ▫ Automatic T ransmission ................ 3 2 5 m Engine Block Heater — If Equipped ......... 3 2 7 m Automatic T ransmission .................. 3 2 8 ▫ Brake/T ransmission Interlock System .
▫ Flowing/Rising W ater .................. 3 4 6 m T ire Safety Information ................... 3 4 8 ▫ T ire Markings ........................ 3 4 8 ▫ T ire Loading And T ire Pressur e ........... 3 5 3 m T ires — General Information ........
▫ Maintenance ......................... 3 8 8 m V ehicle Loading ........................ 3 8 8 ▫ V ehicle Certification Label ............... 3 8 9 m T railer T owing ......................... 3 9 3 ▫ Common T owing Definitions ............. 3 9 3 ▫ T owing T ips .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instr uct all other occupants to buckle their seat belts. W ARNING! NEVER leave unattended children alone in a vehicle.
Automatic T ransmission The gear selector lever must be in the NEUTRAL or P ARK position before you can start the engine. Depr ess the brake pedal before shifting into any driving gear . Normal Starting (Above 32°F/0°C) 1. DO NOT depress the accelerator .
If The Engine Fails T o Start W ARNING! • NEVER pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury . • DO NOT attempt to push or tow your vehicle to get it started.
If the engine shows no sign of starting after two 15– second intervals of cranking with the accelerator pedal held to the floor , the “Normal Starting” procedure should be repeated. After Starting The idle speed will automatically decrease as the engine warms up.
AUTOMA TIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift the gear selector lever into P ARK only after the vehicle has come to a complete stop. • Do not shift the gear selector lever from RE- VERSE, P ARK, or NEUTRAL into any forward gear when the engine is above idle speed.
while the ignition switch is in the ON position. Always press the brake pedal first befor e moving the gear selec- tor lever out of P ARK. Automatic T ransmission Ignition Interlock System For electrical system malfunctions, there is an override for the interlock system.
the instrument cluster will display transmission gear selection as 6, 5, 4, 3, 2, 1 for six-speed and 4, 3, 2, 1 for four-speed transmissions. Gear Ranges DO NOT race the engine when shifting the gear selector lever from P ARK or NEUTRAL positions into another gear range.
W ARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the gear selector lever into P ARK, remove the key from the ignition, and apply the parking brake.
REVERSE Use REVERSE for moving the vehicle rearwar d. Shift into REVERSE only after the vehicle has come to a complete stop. NEUTRAL Shift the gear selector lever into this gear only after the vehicle has come to a complete stop. The engine may be started in this range.
under heavy loading conditions, (i.e., in hilly terrain, traveling into strong head winds or while towing heavy trailers). Under these conditions, using the “3” range will improve performance and extend transmission life by reducing excessive shifting and heat build-up.
Odometer Screen Display 1 234 5 6D Actual Gear(s) Allowed —Six- Speed T rans- mission 1 1-2 1-3 1-4 1-5 1-6 1-6 Actual Gear(s) Allowed —Four-Speed T ransmission 1 1-2 1-3 1-4 N/A N/A 1–4 NOTE: T o select the proper gear position for maximum deceleration (engine braking), simply press and hold the gear selector lever to the left (-).
5. Shift into the desired gear range and r esume driving. NOTE: Even if the transmission can be reset, it is recommended that you visit an authorized dealer at your earliest possible convenience. Y our authorized dealer has diagnostic equipment to determine if the problem could recur .
before placing the gear selector lever in P ARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector lever out of P ARK. W ARNING! • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury .
BRAKE SYSTEM Y our vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability , the remaining system will still function.
ANTI-LOCK BRAKE SYSTEM (ABS) ABS provides incr eased vehicle stability and brake per- formance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. ABS is activated during braking under certain road or stopping conditions.
W ARNING! • The Anti-Lock Brake System cannot prevent acci- dents, including those resulting from excessive speed in turns, following another vehicle too closely , or hydroplaning.
to the ABS system is requir ed. Consult with your autho- rized dealer service center as soon as possible. ELECTRONIC BRAKE CONTROL SYSTEMS Y our vehicle is equipped with an advanced electronic brake control system that includes TCS (T raction Control System), BAS (Brake Assist System) and ESP (Electronic Stability Program).
W ARNING! • The TCS cannot prevent the natural laws of phys- ics from acting on the vehicle, nor can it increase the traction afforded. • The TCS cannot prevent accidents, including those resulting from excessive speed in turns, or hydro- planing.
W ARNING! • BAS (Brake Assist System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevail- ing road conditions. • BAS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
ESP ON This is the normal operating mode for ESP on 2WD vehicles. Whenever the vehicle is started, the ESP system will be in this mode. This mode should be used for most driving situations. ESP should only be turned of f for specific reasons as noted below .
Light comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system. If this light remains on after several ignition cycles, and the vehicle has be.
W ARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible.
TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and r oad surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability . T o reduce this possibility , the following precau- tions should be observed: 1.
Shallow Standing W ater Although your vehicle is capable of driving through shallow standing water , consider the following Caution and W arning before doing so.
W ARNING! • Driving through standing water limits your vehi- cle’ s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water . • Driving through standing water limits your vehi- cle’ s braking capabilities, which increases stop- ping distances.
NOTE: • P (Passenger) - Metric tir e sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tir e sizing is based on European design standards.
T ire Sizing Chart T ire Sizing Chart P Passenger Car tire size based on U.S. design standar ds ( ....blank.... ( Passenger Car tire based on Eur opean design standards LT Light T ruck tire based on U.
T ire Sizing Chart H A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.
T ire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however , the date code may only be on one side. T ires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressure is listed on either the face of the driver’s door or the driver’s side B-Pillar .
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loadi.
amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
356 ST ARTING AND OPERA TING.
2W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
W ARNING! • Unequal tire pressures can cause steering problems. Y ou could lose control of your vehicle. • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure.
The pressur e should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pr essure. DO NOT make a visual judgement when determining proper inflation.
T ire pr essures change by approximately 1 psi (7 kPa) per 12 F (7 C) of air temperature change. Keep this in mind when checking tire pr essure inside a garage, especially in the winter .
Radial-Ply T ires W ARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly . The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
DO NOT install a wheel cover or attempt to mount a conventional tire on the compact spar e wheel, since the wheel is designed specifically for the compact spare.
W ARNING! • Keep the limited use spare tire inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assem- bly . • Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle.
T read W ear Indicators T read wear indicators ar e in the original equipment tires to help you in determining when your tires should be r eplaced. These indicators are molded into the bottom of the tr ead grooves. They will appear as bands when the tr ead depth becomes 1/16 in (2 mm).
Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Pr otect tires from contact with oil, grease, and gasoline. Replacement T ires The tires on your new vehicle pr ovide a balance of many characteristics. They should be inspected regularly for wear and correct cold tir e inflation pressure.
W ARNING! • NEVER use a tire with a smaller load index or capacity , other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. Y ou could lose control and have an accident.
TIRE CHAINS Use only compact chains, or other traction aids that meet SAE type “Class S” specifications. Chains must be the proper size for the vehicle, as r ecommended by the chain manufacturer . NOTE: Do not use tire chains on a compact spar e tire.
Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufactur e suggest a maximum speed. This notice applies to all chain traction devices, including link and cable (radial) chains. SNOW TIRES Some areas of the country r equire the use of snow tires during W inter .
The suggested rotation method is the “forwar d-cross” shown in the following diagram. TIRE PRESSURE MONITOR SYSTEM (TPMS) The TPMS will warn the driver of a low tire pr essure based on the cold inflation tire pr essure requir ements found on the tire placar d located on the driver’s-side B-pillar .
increased to the r ecommended cold tire placard pr essure in order for the TPMS warning lamp to be turned of f. The system will automatically update and the TPMS warning lamp will extinguish once the updated tire pr essures have been received. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) to receive this information.
CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent mois- ture and dirt from entering the valve stem, which could damage the TPMS SENSOR. NOTE: • The TPMS is not intended to replace normal tir e care and maintenance, or to provide warning of a tir e failure or condition.
The Basic TPMS consists of the following components: • Receiver Module • Four Wheel Sensors • TPMS T elltale W arning Light The TPMS T elltale W arning Light will illumi- nate in the instrument cluster , and an audible chime will be activated when one or more of the four active road tir e pressures ar e low .
NOTE: 1. The compact spare tir e (if equipped) does not have a TPMS sensor . Therefore the TPMS will not monitor the pressur e in the compact spare tire.
• Three T rigger Modules (mounted in three of the four wheel wells) • V arious TPMS Messages, which display in the Elec- tronic V ehicle Information Center (EVIC), and graph- ics displaying tire p.
Should a low tire condition occur on any of the four active road tir e(s), you should stop as soon as possible, and inflate the low tire(s) that is flashing on the graphic display to the vehicle’s recommended cold tir e pressure value.
will not be present, and a pr essure value will be dis- played instead of dashes. A system fault can occur by any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPMS sensors.
5. Once you repair or r eplace the original road tire, and reinstall it on the vehicle in place of the compact spar e, the TPMS will update automatically .
gasolines, and in some circumstances may r esult in poorer performance. 4.0L Gasoline Engine The 4.0L engine is designed to meet all emissions regulations and pr ovide satisfac- tory fuel economy and performance when using high-quality unleaded gasoline hav- ing an octane range of 87 to 89.
The manufacturer supports the use of r eformulated gaso- lines. Properly blended r eformulated gasolines will pro- vide excellent performance and durability of engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE.
It is even more important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. MMT is prohibited in Federal and California r eformu- lated gasolines. Materials Added to Fuel All gasoline sold in the United States is requir ed to contain effective deter gent additives.
• The use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting fr om the use of such fuels or additives is not the responsibility of the manufactur er .
W ARNING! Carbon monoxide (CO) in exhaust gases is deadly . Follow the precautions below to prevent carbon monoxide poisoning: • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised.
CAUTION! Damage to the fuel system or emission control sys- tem could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system and may cause the Malfunction Indicator Light (MIL) to turn on due to fuel vapors escaping from the system.
W ARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. Y ou could be burned. Always place gas containers on the ground while filling.
CAUTION! Only vehicles with the E-85 Decal and/or fuel filler door label can operate on E-85. ETHANOL FUEL (E-85) E-85 is a mixture of appr oximately 85% fuel ethanol and 15% unleaded gasoline.
W ARNING! Ethanol vapors are extremely flammable and could cause serious personal injury . Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
Selection Of Engine Oil For Flexible Fuel V ehicles (FFV) E-85 and Gasoline V ehicles FFV vehicles operated on E85 requir e specially formulated engine oils. These special requir ements are included in Mopar t engine oils, and in equivalent oils meeting DaimlerChrysler Specification MS-6395.
Maintenance If you operate the vehicle using E-85 fuel, follow the maintenance schedule section of this manual. CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability .
V ehicle Certification Label Y our vehicle has a V ehicle Certification Label attached to the driver’s door pillar . The label contains the following information: • Name of manufacturer • Month .
T ire Size The tire size on the V ehicle Certification Label repr esents the actual tire size on your vehicle. Replacement tir es must be equal to the load capacity of this tire size. Rim Size This is the rim size that is appropriate for the tir e size listed.
Loading T o load your vehicle properly , first figure out its empty weight, axle by axle and side by side. Store heavier items down low and be sure you distribute their weight as evenly as possible.
A loaded vehicle is shown in the illustration. Note that neither the GVWR or the GA WR capacities have been exceeded. LOADING T ABLE — EXAMPLE ONL Y Front Axle Rear Axle Empty W eight 2,140 lbs (971.
TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer car efully re- view this information to tow your load as efficiently and safely as possible.
Gross Axle W eight Rating (GA WR) The GA WR is the maximum capacity of the front and rear axles. Distribute the load over the front and r ear axles evenly . Make sure that you do not exceed either front or rear GA WR. W ARNING! It is important that you do not exceed the maximum front or rear GA WR.
W eight-Distributing Hitch A weight-distributing system works by applying lever- age through spring (load) bars. They ar e typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer’s axle(s).
W eight Distributing Hitch System Improper Adjustment of W eight Distributing System 396 ST ARTING AND OPERA TING.
T railer Hitch Classifications Y our vehicle may be factory-equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional T railer T ow Prep Package.
T railer T owing W eights (Maximum T railer W eight Ratings) The T railer T owing W eights Chart provides the maximum trailer weight ratings towable for a given drivetrain. TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RA TINGS) Engine/ T ransaxle GCWR (Gross Combined Wt.
T railer and T railer T ongue W eight Always load a trailer with 60% to 65% of the weight in the front of the trailer . This places 10% to 15% of the Gross T railer W eight (GTW) on the tow hitch of your vehicle.
NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle.
W ARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
4. T railer tongue weight rating for that trailer hitch. (This requir ement may limit the ability to always achieve the 10% to 15% range of trailer tongue weight as a percentage of total trailer weight.) T owing Requirements — T ires • Do not attempt to tow a trailer while using a compact spare tir e.
• T railer brakes are r ecommended for trailers over 1,000 lbs (454 kg) and requir ed for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity .
T owing Requirements — T railer Lights and W iring Whenever you pull a trailer , regardless of the trailer size, stop lights and turn signals on the trailer are r equired for motoring safety . The T railer T ow Package may include a four-pin or a seven-pin wiring harness.
T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away fr om heavy traffic. T owing T ips — Automatic T ransmission The DRIVE gear can be selected when towing.
NOTE: • Check the automatic transmission fluid level before towing. • The six-speed automatic transmission is sealed and requir es an authorized dealer service center to check the transmission fluid. T owing T ips — Electronic Speed Control (If Equipped) • Don’t use in hilly terrain or with heavy loads.
RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.) CAUTION! T owing this vehicle behind another vehicle (flat- towing with all four wheels on the ground) IS NOT RECOMMENDED. NOTE: If the vehicle requir es towing make sure all four wheels are of f the ground.
.
WHA T T O DO IN EMERGENCIES CONTENTS m Hazard W arning Flasher .................. 4 1 0 m If Y our Engine Overheats ................. 4 1 0 m Jacking And T ire Changing ................ 4 1 2 ▫ Jack Location ........................ 4 1 3 m Jump-Starting Procedur e .
HAZARD W ARNING FLASHER The hazard flasher switch is located in the center of the instrument panel below the radio. T o engage the Hazard W arning Flashers, depress the switch on the instrument panel. When the Hazar d W arn- ing Switch is activated, all directional turn signals will flash on and off to warn oncoming traf fic of an emer- gency .
the fan control to High. This allows the heater cor e to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle.
JACKING AND TIRE CHANGING W ARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.
Jack Location The jack, jack handle and winch handle tools are stowed behind the rear left side trim panel in the r ear cargo area. T urn the two cover latches to release the cover . Remove the pouch containing the scissors jack, jack handle, and tools.
Spare T ire Removal For vehicles equipped with Stow ’n Go seating, the spare tire is stowed inside a pr otective cover located under the center of the vehicle by means of a cable winch mecha- nism. The “spare tir e drive” nut is located on the floor , under a plastic cap at the front of the floor console.
Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in P ARK. T urn OFF the ignition. • T urn on the Hazard W arning Flasher . • Block both the front and r ear of the wheel diagonally oppo- site the jacking position.
W ARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised.
1. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 2. T o remove the compact spar e tire/cover assembly , assemble the winch handle extensions to form a “T’ and fit the winch “T” handle over the drive nut.
NOTE: If either front tir e is flat, it may be necessary to jack up the vehicle to remove the compact spar e tire/ cover assembly from under the vehicle.
5. There ar e two jack engagement locations on each side of the vehicle body . These locations are on the sill flange of the vehicle body . NOTE: Rear jack location is between a pair of down- standing tabs on the sill flange of the vehicle body . Front jack location is on the sill flange of the vehicle body and aligns with the front door edge.
Jack Location 420 WHA T TO DO IN EMERGENCIES.
CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in Step 5. 6. Place the wrench on the jack scr ew and turn to the right until the jack head is properly engaged in the described location. Do not raise the vehicle until you are sure the jack is securely engaged.
10. Lower the vehicle by turning the jack screw to the left. 1 1. Finish tightening the lug nuts. Push down on the wrench while tightening for incr eased leverage. Alternate lug nuts until each nut has been tightened twice. Correct wheel nut tightness is 95 ft lbs (130 N·m).
of operation, and after each time a tire is changed, to allow the wheel nuts to become properly set. All nuts should first be firmly seated against the wheel. The nuts should then be tightened to recommended tor que. T ighten the nuts to final torque in incr ements.
2. Assemble the winch handle extensions to form the Spare T ire Hook and pull the wheel spacer from under the vehicle. 3. T urn the compact spare tir e so that the valve stem is down and place the tire into the spar e tire cover assem- bly .
CAUTION! For vehicles equipped with Stow ’n Go seating, the W inch Mechanism is designed specifically to stow a COMP ACT Spare T ire ONL Y . Do not attempt to use the W inch to stow the Full Size ’Flat’ T ire, or any other Full Size T ire. V ehicle damage may result.
When jump-starting, proceed as follows: 1. W ear eye protection and r emove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When a boost is pr ovided by a battery in another vehicle, park that vehicle within booster cable reach and without letting the vehicles touch.
6. Start the engine in the vehicle which has the booster battery , let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery . 7. When removing the jumper cables, r everse the above sequence exactly . Be careful of the moving belts and fan.
CAUTION! Racing the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 35 mph (55 km/h).
CAUTION! • Do not push or tow this vehicle with another vehicle as damage to the bumper fascia and trans- mission may result. • If the vehicle being towed requires steering, the ignition switch must be in the OFF position, not in the LOCK or ACC positions.
.
MAINT AINING YOUR VEHICLE CONTENTS m 3.3L Engine Compartment ................ 4 3 4 m 3.8L Engine Compartment ................ 4 3 5 m 4.0L Engine Compartment ................ 4 3 6 m Onboard Diagnostic System — OBD II ........ 4 3 7 ▫ Loose Fuel Filler Cap Message — gASCAP .
▫ Power Steering — Fluid Check ............ 4 5 2 ▫ Front Suspension — Ball Joints ............ 4 5 3 ▫ Steering Shaft Seal .................... 4 5 3 ▫ Drive Shaft Universal Joints .............. 4 5 4 ▫ Body Lubrication ...............
▫ Center High-Mounted Stop Light (CHMSL) . . . 485 ▫ License Light ........................ 4 8 5 m Fluids And Capacities ................... 4 8 6 m Fluids, Lubricants And Genuine Parts ........ 4 8 7 ▫ Engine ............................. 4 8 7 ▫ Chassis .
3.3L ENGINE COMP ARTMENT 434 MAINT AINING YOUR VEHICLE.
3.8L ENGINE COMP ARTMENT MAINT AINING YOUR VEHICLE 435 7.
4.0L ENGINE COMP ARTMENT 436 MAINT AINING YOUR VEHICLE.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
Loose Fuel Filler Cap Message — gASCAP Should the “Loose Fuel Filler Cap” or “gASCAP” mes- sage appear , there may be a problem in the evaporative system. Before taking the vehicle into an authorized dealer , check first to see if the fuel filler cap is possibly loose, improperly installed, or damaged.
This vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. T o check if this vehicle’s OBD II system is ready , you must do the following: 1. Insert the ignition key into the ignition switch. 2. T urn the ignition to the ON position, but do not crank or start the engine.
serviced before going to the I/M station. The I/M station can fail the vehicle because the MIL is on with the engine running. REPLACEMENT P ARTS Use of genuine Mopar t parts for normal/scheduled maintenance and repairs is highly r ecommended to en- sure the designed performance.
MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there ar e fixed maintenance intervals, there ar e other items that should operate satisfactorily without periodic maintenance.
Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level r eadings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX r eading on these engines.
recommends engine oils that ar e API certified and meet the requir ements of DaimlerChrysler Material Standard MS-6395. American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API).
Synthetic Engine Oils Y ou may use synthetic engine oils provided the r ecom- mended oil quality requir ements are met, and the recom- mended maintenance intervals for oil and filter changes are followed.
DRIVE BEL T At the mileage indicated in the maintenance schedule, replace the drive belt with a new drive belt. NOTE: The drive belt must be routed corr ectly to ensure proper drive function. SP ARK PLUGS Spark plugs must fire pr operly to assure engine perfor- mance and emission control.
CA T AL YTIC CONVERTER The catalytic converter requir es the use of unleaded fuel only . Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not requir e maintenance.
W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.
Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for br oken, damaged, deteriorated, or mispositioned parts.
W ARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water .
AIR CONDITIONER MAINTENANCE For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check.
Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluor o- carbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving pr oduct.
4. Disengage the two retaining tabs that secur e the filter cover to the HV AC housing and remove the cover . 5. Remove the A/C Air Filter by pulling it straight out of the housing. 6. Install the A/C Air Filter with the arrow on the filter pointing toward the floor .
apparent, and/or the system is not functioning as antici- pated. Coordinate inspection ef forts through an autho- rized DaimlerChrysler Dealership. 9 W ARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading.
DRIVE SHAFT UNIVERSAL JOINTS Y our vehicle has constant velocity universal joints. Peri- odic lubrication of these joints is not requir ed. However , the joint boots should be inspected for external leakage or damage when other maintenance is performed.
A void using the wiper blades to remove fr ost or ice from the windshield. Keep the blade rubber out of contact with petroleum pr oducts such as engine oil, gasoline, etc. W indshield and Rear Window W ashers The fluid reservoir for the windshield washers and the rear window washer is shar ed.
COOLING SYSTEM W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at anytime the ignition switch is in the ON position.
drain from the coolant r ecovery bottle. DO NOT RE- MOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT . Cooling System — Drain, Flush and Refill The system should be drained, flushed, and refilled at the intervals shown in the “Maintenance Schedule” in Sec- tion 8 of this manual.
Adding Coolant Y our vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to five years or 102,000 mi (170 000 km) before r eplacement. T o prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle.
W ARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points T o Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the fr ont of the engine compartment.
• Do not change the thermostat for summer or winter operation. If replacement is ever necessary , install ONL Y the corr ect type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions.
BRAKES In order to assur e brake system performance, all brake system components should be inspected periodically . Suggested service intervals can be found in the Mainte- nance Schedules. W ARNING! Riding the brakes can lead to brake failure and possibly an accident.
NOTE: Inspection of brake hoses should be performed whenever the brake system is serviced and every engine oil change. Inspect hydraulic brake hoses for surface cracking, scuffing, or worn spots.
W ARNING! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of a brake fluid that has a lower initial boiling .
All six speed transaxles are equipped with a capped dipstick tube, it is sealed and should not be tampered with. Y our authorized dealer has the necessary tools to ensure that the fluid level is set pr operly . Selection of Lubricant It is important that the proper lubricant is used in the transaxle to assure optimum transaxle performance.
Fluid Level Check — 3.3L Engine with Four -Speed Automatic T ransaxle — If Equipped The dipstick is located just behind the radiator , lower right side. T o properly check the automatic transaxle fluid level, the following procedur e must be used: 1.
If the fluid level indicates low , add sufficient fluid to bring to the proper level. CAUTION! Do not overfill. Dirt and water in the transaxle can cause serious damage. T o prevent dirt and water from entering the transaxle after checking or replenishing fluid, make certain that the dipstick cap is reseated properly .
trees and r oad surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehic.
• A void using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder , which will scratch metal and painted surfaces.
Wheel and Wheel T rim Care All wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned r egularly with a mild soap and water to prevent corr osion. T o remove heavy soil and/or excessive brake dust, use Mopar t Wheel Cleaner (05066247AB) or equivalent or select a nonabrasive, non-acidic cleaner .
soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia-based cleaners to clean your leather upholstery . Application of a leather conditioner is not requir ed to maintain the original condition.
2. T o maintain the high gloss shine, apply a scratch and swirl remover onto a damp cloth and apply to door applique. Rub the applique with a firm pressur e then buff lightly with a clean cotton cloth until a high gloss shine is achieved.
1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the seatbelts with chemical solvents or abrasive cleaners.
Installation Place the liner into the cupholder drawer and press the liner into place so that the retention tabs seat into the corresponding openings in the drawer . FUSES/TOT ALL Y INTEGRA TED POWER MODULE (TIPM) The T otally Integrated Power Module (TIPM) is located in the engine compartment near the battery .
FUSES/TIPM Cavity Cartridge Fuse Mini Fuse Description J1 40 Amp Green — Power Folding Seat J2 30 Amp Pink — Power Liftgate Module J3 40 Amp Green — Rear Door Module (RR Door Node) J4 25 Amp Nat.
FUSES/TIPM Cavity Cartridge Fuse Mini Fuse Description J21 20 Amp Y ellow — Front/Rear W asher J22 25 Amp Natural — Sunroof Module M1 — 15 Amp Blue Center High Mounted Stop Light (CHMSL)/ Brake .
FUSES/TIPM Cavity Cartridge Fuse Mini Fuse Description M12 — 30 Amp Green Amplifier (AMP) M13 — 20 Amp Y ellow Ignition Off Draw— Cabin Compartment Node (IOD-CCN), W ire- less Control Module (WC.
FUSES/TIPM Cavity Cartridge Fuse Mini Fuse Description M17 — 15 Amp Blue Left T ail/License/Park Lamp (L T -T AIL/LIC/ PRK LMP) M18 — 15 Amp Blue Right T ail/Park/Run Lamp (R T -T AIL/PRK/ RUN LMP.
FUSES/TIPM Cavity Cartridge Fuse Mini Fuse Description M29 — 10 Amp Red Occupant Classification Module (OCM) M30 — 15 Amp Blue Rear W iper Module (RR WIPER MOD), Power Folding Mirror (PWR FOLD MIR.
FUSES/TIPM Cavity Cartridge Fuse Mini Fuse Description M38 — 25 Amp Natural Lock/Unlock Motors (LOCK/UNLOCK MTRS) CAUTION! • When installing the Integrated Power Module cover , it is important to ensure the cover is prop- erly positioned and fully latched.
The Heated Mirrors, Lower Instr ument Panel Power Outlet and Removable Floor Console, when in the front position are fused with self-r esetting fuses that are only serviceable by an authorized dealer . The power seats are fused by a 30 Amp circuit br eaker located under the driver’s seat.
NOTE: For lighted switches, see your dealer for replace- ment. All of the interior bulbs are glass wedge base or glass cartridge types. Aluminum base bulbs are not approved and should not be used for replacement. LIGHT BULBS — Exterior Bulb Number Backup, T ail, Stop Light .
5. Connect the wiring connector to bulb and slide red lock tab forward. Front Park/T urn Signal and Side Marker Lights 1. Raise the hood to access the rear of the headlight housing. 2. T wist the turn signal socket and remove fr om the headlight housing, then pull the bulb out.
Rear T ail, Stop, T urn Signal, Side Marker and Backup Lights 1. Raise the liftgate. 2. Remove the tail light assembly by removing the two screws fr om the inboard side. Use a fiber stick or similar tool to gently pry the light on the outboard side to disengage the two ball studs.
3. T wist the socket and remove form the light assembly . 4. Pull the bulb to remove it fr om the socket. 5. Replace the bulb, reinstall the socket, and r eattach the light assembly . Center High-Mounted Stop Light (CHMSL) The CHMSL uses LED lights that are not serviceable separately .
FLUIDS AND CAP ACITIES FLUIDS AND CAP ACITIES U.S. Metric Fuel (approximate) All Engines 20 Gals 76 L Engine Oil with Filter 3.3L and 3.8L (SAE 5W -20 API Certified) 5.0 Qts 4.7 L 4.0L (SAE 10W -30 API Certified) 5.5 Qts 5.2 L Cooling System 3 3.3L, 3.
FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine FLUIDS, LUBRICANTS AND GENUINE P AR TS — ENGINE Component Fluids, Lubricants and Genuine Parts Coolant Mopar t Antifreeze/Coolant Five Y ear/100,000 Mile Formula HOA T (Hybrid Organic Additive T echnology) or equivalent Oil – 3.
Chassis FLUIDS, LUBRICANTS AND GENUINE P AR TS — CHASSIS Component Fluids, Lubricants and Genuine Parts Automatic T ransmission Mopar t A TF+4 Automatic T ransmission Fluid Brake Master Cylinder Mopar t DOT 3 and SAE J1703 should be used or equivalent.
MAINTENANCE SCHEDULES CONTENTS m Emissions Control System Maintenance ....... 4 9 0 m Maintenance Schedule ................... 4 9 0 ▫ Required Maintenance Intervals .
EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emissions Con- trol System.
NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-r oad for an extended period of time.
• Check the fluid levels of coolant reservoir , brake master cylinder , power steering and transmission and add as needed. • Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter . • Inspect the brake hoses and lines.
Required Maintenance Intervals Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Change the engine oil and engine oil filter . 6,000 10 000 6 Rotate T ires.
Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Change the automatic transmission fluid & filter if using your vehicle for any of the following: police, taxi, fleet or frequent trailer towing.
W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS m Suggestions For Obtaining Service For Y our V ehicle .............................. 4 9 9 ▫ Prepar e For The Appointment ............ 4 9 9 ▫ Prepar e A List ........................ 4 9 9 ▫ Be Reasonable W ith Requests .
m Department Of T ransportation Uniform T ire Quality Grades ........................ 5 0 5 ▫ T readwear .......................... 5 0 5 ▫ T raction Grades .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty .
high quality service. The manufacturer’s authorized deal- ers have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner . This is why you should always talk to an authorized dealer’s service manager first.
Chrysler Canada Inc. Customer Center P .O. Box 1621 W indsor , Ontario N9A 4H6 Phone: (800) 465–2001 In Mexico contact: A v . Prolongacion Paseo de la Reforma, 1240 Sante Fe C.
service contract that is not a manufacturer’s Service Contract, and you requir e service after the manufactur- er’s New V ehicle Limited W arranty expires, please refer to the contract documents, and contact the person listed in those documents. W e appreciate that you have made a major investment when you purchased the vehicle.
MOP AR T P ARTS Mopar t fluids, lubricants, parts, and accessories are available from an authorized dealer . They will help keep the vehicle operating at its best.
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Expr ess, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Call toll free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orldwide W eb at: • www .techauthority .com DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following tire grading categories wer e established by the National Highway T raffic Safety Administration.
W ARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
INDEX 10.
Adding Engine Coolant (Antifreeze) .......... 4 5 8 Adding Fuel ........................... 3 8 2 Adding W asher Fluid ..................... 4 5 5 Additives, Fuel ......................... 3 8 0 Adjustable Pedals ....................... 1 7 7 Air Cleaner , Engine (Engine Air Cleaner Filter) .
Automatic Dimming Mirror ................ 1 0 0 Automatic Door Locks ................... 34,35 Automatic Headlights .................... 1 6 3 Automatic T emperature Contr ol (A TC) ......... 3 0 9 Automatic T ransaxle ...................... 3 2 8 Adding Fluid .
Brakes ............................. 337,462 Brake/T ransmission Interlock ............... 3 2 8 Break-In Recommendations, New V ehicle ........ 9 3 Bulb Replacement ....................... 4 8 2 Bulbs, Light ............................ 4 8 1 Calibration, Compass .
Coin Holder ........................... 2 0 1 Cold W eather Operation ................... 3 2 5 Compact Disc (CD) Maintenance ............. 3 0 0 Compact Spare T ire ...................... 3 6 1 Compass ........................ 238,240,246 Compass Calibration .
Digital V ideo Disc (DVD) Player .......... 280,283 Dimmer Control ........................ 1 6 2 Dimmer Switch, Headlight ................. 1 7 0 Dipsticks Automatic T ransaxle .................... 4 6 5 Automatic T ransmission ................. 4 6 6 Oil (Engine) .
Emission Control System Maintenance ...... 438,490 Engine ........................ 93,434,435,436 Air Cleaner .......................... 4 4 5 Block Heater ......................... 3 2 7 Break-In Recommendations ................ 9 3 Checking Oil Level .
Flashers Hazard W arning ....................... 4 1 0 T urn Signal ..................... 227,483,484 Flash-T o-Pass ........................... 1 7 0 Flat T ire Stowage ........................ 4 2 2 Flexible Fuel V ehicles Cruising Range ...........
Requirements ...................... 377,486 System Hoses ......................... 4 6 1 T ank Capacity ........................ 4 8 6 Fuel, Flexible ............. See Flexible Fuel V ehicles Fuel System Caution ..................... 3 8 0 Fueling ...
Passing ............................. 1 7 0 Replacing ............................ 4 8 2 T ime Delay .......................... 1 6 4 Heated Seats ........................... 1 3 5 Heater ............................... 3 0 1 Heater , Engine Block ...
Key , Sentry (Immobilizer) ................... 1 5 Key-In Reminder ......................... 1 5 Keyless Entry System ...................... 2 1 Keys ................................. 1 2 Knee Bolster ............................ 6 7 Lap/Shoulder Belts .
License ............................. 4 8 5 Lights On Reminder .................... 1 6 5 Low Fuel ............................ 2 3 4 Malfunction Indicator (Check Engine) ........ 2 3 2 Oil Pressur e .......................... 2 3 3 Park .............
Memory Seat ........................ 104,155 Mini-T rip Computer ................... 238,244 Mirrors ............................... 1 0 0 Automatic Dimming .................... 1 0 0 Electric Remote ..................... 102,103 Exterior Folding ....
Outside Rearview Mirrors ............... 100,102 Overdrive ............................. 3 3 2 Overhead Console ....................... 1 8 2 Overhead T ravel Information Center .......... 1 8 2 Overheating, Engine ................... 226,410 Owner’s Manual (Operator Manual) .
Pretensioners Seat Belts ............................. 6 4 Programmable Electr onic Features ............ 2 4 8 Radial Ply T ires ......................... 3 6 1 Radiator Cap (Coolant Pressur e Cap) ....... 457,458 Radio Broadcast Signals ............
Safety Checks Outside V ehicle ............... 9 4 Safety Defects, Reporting .................. 5 0 3 Safety , Exhaust Gas ....................... 5 1 Safety Information, T ire ................... 3 4 8 Safety T ips ............................. 9 3 Satellite Radio .
Service Engine Soon Light (Malfunction Indicator) . . 232 Service Manuals ........................ 5 0 4 Setting the Clock ................ 254,269,281,285 Settings, Personal ........................ 2 4 8 Shoulder Belts ........................... 5 7 Signals, T urn .
Synthetic Engine Oil ...................... 4 4 4 System, Navigation ...................... 2 8 3 System, Remote Starting .................... 2 8 T achometer ............................ 2 2 9 T emperature Contr ol, Automatic (A TC) ........ 3 0 9 T emperature Gauge, Engine Coolant .
T read W ear Indicators ................... 3 6 4 Wheel Nut T orque ..................... 4 2 2 T ongue W eight/T railer W eight .............. 3 9 9 T owing ............................... 3 9 3 24-Hour T owing Assistance ............... 1 1 7 Disabled V ehicle .
UConnect™ (Hands-Free Phone) .......... 104,283 Uniform T ire Quality Grades ................ 5 0 5 Universal Consumer Interface (UCI) Connector . . . 292 Universal Joints ......................... 4 5 4 Universal Serial Bus (USB) Port ........... 280,283 Universal T ransmitter .
W indshield W iper Blades .................. 4 5 4 W indshield W ipers ....................... 1 6 8 W iper Blade Replacement .................. 4 5 4 W ipers, Intermittent ...................... 1 6 9 YES Essentials t Fabric Cleaning Procedur e .....
INST ALLA TION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to pr ovide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel.
Car a v an OWNER’ S MANUAL 2008 2008 Car a v an 81-226-0819 Fourth Edition P r inted in U .S.A..
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Dodge 2008 Caravan c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Dodge 2008 Caravan - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Dodge 2008 Caravan, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Dodge 2008 Caravan va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Dodge 2008 Caravan, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Dodge 2008 Caravan.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Dodge 2008 Caravan. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Dodge 2008 Caravan ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
