Manuel d'utilisation / d'entretien du produit 2006 Dakota du fabricant Dodge
Aller à la page of 408
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 7 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 5 䡵 V ehicle Identification Number ............... 5 䡵 V ehicle Modifications / Alterations .
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information.
VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 0 ▫ Key-In-Ignition Reminder ................ 1 0 ▫ Sentry Key Immobilizer — If Equipped ....... 1 0 䡵 Ignition And Steering Lock ........
▫ Battery Replacement .................... 2 5 䡵 Security Alarm System — If Equipped ......... 2 6 ▫ T o Set The Alarm ...................... 2 6 ▫ T o Disarm The System ................... 2 7 䡵 W indows ............................. 2 8 ▫ Power W indows .
䡵 Safety T ips ............................ 7 1 ▫ Exhaust System ....................... 7 1 ▫ Safety Checks Y ou Should Make Inside The V ehicle .............................. 7 2 ▫ Safety Checks Y ou Should Make Outside The V ehicle ........
A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to or der duplicate keys from your dealer or a locksmith.
on the remaining transmitters will work. If the vehicle is moving 5 mph or more, then all the transmitter buttons are disabled for all keys. NOTE: The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting pr oblems and a loss of security protection.
consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed and needs to be cut. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer . Customer Key Programming Y ou can program new keys to the system if you have two valid keys by doing the following: 1.
NOTE: Changes or modifications not expressly ap- proved by the party r esponsible for compliance could void the user’s authority to operate the equipment. IGNITION AND STEERING LOCK Insert the key fully , and then turn the switch to one of the five illustrated positions.
easily . The key can be inserted or withdrawn only in the LOCK position. Push in on the key in the ignition lock cylinder to rotate to the LOCK position. NOTE: The steering wheel will lock when the key is removed, and the steering wheel is turned 1 15 degrees from center clockwise and 65 degr ees counterclockwise.
DOOR LOCKS Manual Door Locks All the doors can be “manually” locked from the inside by pushing down the door lock plunger , located on the door trim panel. Both front doors may be opened fr om the inside with the door lock plunger in the down or locked position.
Power Door Locks V ehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pr essing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob.
As a safety feature the doors will not lock when using the door lock switches during the following conditions: • The driver’s door is open while the key is in the ignition. Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
• The vehicle is in P (Park) and the ignition switch is in any key position . This feature will not operate if any of the conditions above are not met or following has occurr ed: • Any manual operation of a door lock switch has occurred. NOTE: This customer programmable featur e is enabled when your vehicle is shipped from the assembly plant.
Child Protection Door Lock T o provide a safer envir onment for children riding in the rear seat, the r ear doors of your vehicle have the child- protection door lock system. T o use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks.
W ARNING! A void trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
NOTE: The line of transmission must not be blocked with metal objects. T o unlock the doors: Press and r elease the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, and the parking lights will flash on twice.
Horn Chirp Programming The horn chirp feature will be shipped fr om the assembly plants activated. If desired this featur e can be disabled by using the following procedur e: 1. Pr ess and hold the LOCK button on the key fob. 2. After holding the LOCK button for four seconds, also press the P ANIC button within 6 seconds.
NOTE: Pressing the LOCK button on the key fob, while you are in the vehicle, will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 5.
1. W eak batteries in transmitter . The expected life of batteries is five years. 2. Closeness to a radio transmitter such as a radio station tower , airport transmitter , military base, and some mobile or CB radios.
8. Using the fob to be pr ogrammed, press and hold both the LOCK and UNLOCK buttons, simultaneously for 2 seconds and then release. 9. Pr ess and release the UNLOCK button a single chime will be heard. 10. Repeat steps 8 and 9 to pr ogram up to six additional fobs.
2. Remove and r eplace the batteries. A void touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery , clean it with rubbing alcohol. 3. T o assemble the transmitter case, snap the two halves together .
T o Disarm the System: Use the Keyless Entry transmitter to unlock the doors. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tampering. The security system will also disarm, if the vehicle is started with a programmed Sentry Key .
WINDOWS Power Windows The control on the left fr ont door has up-down switches that give you finger tip control of all four power win- dows. There is a single opening and closing switch on the passenger doors for passenger window control. The windows will operate only when the ignition switch is turned to the ON position.
Auto Down The driver’s window switch has an Auto Down feature. Push the window switch past the first detent, release, and the window will go down automatically . T o cancel the Auto Down movement, operate the switch in either the up or down direction and r elease the switch.
Sliding Rear Window A locking device in the center of the window helps to prevent entry fr om the rear of the vehicle. Squeeze the lock to release the window . WIND BUFFETING W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears.
Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up.
W ARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the fr ont seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt.
W ARNING! • A belt buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
W ARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. • A twisted belt can’t do its job as well.
Adjustable Upper Shoulder Belt Anchorage In the front r ow outboard seats, the shoulder belt can be adjusted upward or downwar d to help position the belt away from your neck. Push in on the anchorage r elease button to release the anchorage, and then move it up or down to the position that serves you best.
Automatic Locking Mode (if equipped) T o convert from the normal emer gency locking mode to the automatic locking mode, grasp the shoulder belt portion and pull all of the webbing out of the retractor .
The pretensioners ar e triggered by the Occupant Re- straint Controller (ORC). Like the airbags, the pr etension- ers are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced.
3. W ithin 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least thr ee times within 10 seconds, ending with the seat belt buckled. 4. T urn off the engine. A single chime will sound to signify that you have successfully completed the pro- gramming.
W ARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
the instrument panel, above the glove compartment. The words SRS/AIRBAG ar e embossed on the airbag covers. NOTE: The front airbags ar e certified to the Federal regulations that allow less for ceful deployment. The front airbags have a multistage inflator design.
Along with the seat belts, front airbags work with the instrument panel knee bolsters to pr ovide improved protection for the driver and fr ont passenger . W indow bags also work with seat belts to improve occupant protection. The seat belts are designed to pr otect you in many types of collisions.
2. All occupants should use their lap and shoulder belts properly . 3. The driver and fr ont passenger seats should be moved back as far as practical to allow the airbag room to inflate. 4. If your vehicle has window bags, do not lean against the door or window , airbags will inflate forcefully into the space between you and the door .
Air Bag System Components The airbag system consists of the following: • Occupant Restraint Controller • Side Remote Acceleration Sensors (If Equipped) • Airbag W arning Light • Driver Airbag .
The ORC also monitors the readiness of the electr onic parts of the system whenever the ignition switch is in the ST AR T or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters.
NOTE: Children 12 years and under should always ride buckled up in a rear seat in an appr opriate child restraint. • The Passenger Airbag Disable (P AD) Indicator Light (an amber light located in the center of the instrument panel) tells the driver and front passenger when the front passenger airbag is turned of f.
For almost all properly installed r ear facing child re- straints, the P AD indicator light will be illuminated indicating that the front passenger airbag is turned of f and will not inflate.
the OCS has classified the occupant of the seat as an adult. An adult occupant needs to sit in a normal position (with their feet on or near the floor) in order to be properly classified. Reclining the seat back too far may change how an occupant is classified by the OCS.
Indicator Light and the Airbag W arning Light. Once the lodged object is removed, the fault will be automatically cleared after a short period of time. • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel.
or a weight less than the predetermined thr eshold, the ORC will not illuminate the P AD indicator light even though the airbag is turned OFF . • Y our vehicle has four W eight Sensors located within the seat structur e or between the seat tracks and cushion frame.
• Do not modify the front seat center console or center position seat in any way . • Do not use prior or future model year seat covers not designated for the specific model being repair ed. Al- ways use the correct seat cover specified for the vehicle.
NOTE: A frontal collision that is not sever e enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured if the airbag system is not there to protect you.
• The light flickers or comes on and remains on while driving. NOTE: If the speedometer , tachometer or any engine related gauges ar e not working, the airbag control mod- ule may also be disabled. The airbags may not be ready to inflate for your protection.
NOTE: The Passenger Airbag On/Off Switch is not available in the Quad Cab. T o Shut Off the Passenger Frontal Airbag Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn clockwise, and remove the key from the switch. This will shut of f the passenger frontal airbag.
gathered during a complete accident investigation, the electronic data may be used by DaimlerChrysler Corpora- tion and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance.
Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning lamp status for electronically-contr olled safety systems, including the airbag system • Airbag disable lamp status (.
one year old and weigh at least 20 lbs (9 kg). T wo types of child restraints can be used r earward facing: infant carriers and ⬙ convertible ⬙ child seats. • The infant carrier is only used rearwar d-facing in the vehicle. It is recommended for childr en who weigh up to about 20 lbs (9 kg).
belt-positioning booster seat. The child and booster seat are held in the vehicle by the lap/shoulder belt. Children T oo Large for Booster Seats • Children who ar e large enough to wear the shoulde.
Here ar e some tips for getting the most out of your child restraint: • Before buying any r estraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. The manufactur er recommends that you try a child restraint in the vehicle seats wher e you will use it before you buy it.
provides for the installation of the child r estraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorages and upper tether straps from the child r estraint to the vehicle structure. LA TCH- compatible child restraint systems ar e now available.
the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child restraints ar e not LA TCH compatible, you can only install the child restraints using the vehicle’s seat belts. Please refer to the next section for typical installation instructions.
seat lower anchorages are r ound bars, located at the rear of the seat cushion where it meets the seat back, and ar e just visible when you lean into the vehicle to install the child restraint. Y ou will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces.
restraint installation, instead of tucking the seat belt behind the child restraint, r oute the seat belt through the child restraint belt path and then buckle it.
locking retractor seat belts, r efer to ⬙ Automatic Locking Mode ⬙ earlier in this section. If you have trouble tighten- ing the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint, follow these steps.
W ARNING! W ith a child restraint installed in the rear driver or passenger side locations, use care when adjusting the front seat(s) rearward, to avoid the front seat back coming in contact with the belted child directly behind the seat. The child could be injured.
T ether Straps at the Rear Passenger Seat (Club Cab) 1. Route the child r estraint tether strap through the routing loop, located dir ectly behind the child restraint. The routing loops ar e located behind the flip-down door on the cab back panel (padded bolster).
T ether Straps at the Rear Passenger Seat (Quad Cab) 1. Route the child r estraint tether strap under the head restraint for the outboar d seating positions, and then through the anchor strap outer loop (webbing material loop), located directly behind the child r estraint.
Multiple Child Restraint Double Cab THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE 69 2.
W ARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and is not an indication of dif ficulty . SAFETY TIPS Exhaust System W ARNING! Exhaust gases contain carbon monoxide, an ex- tremely toxic gas that by itself is colorless and odorless.
Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor , torn webbing, etc.
Fluid Leaks Check the area under vehicle after overnight parking for fuel, water , oil, or other fluid leaks. Also, if gasoline fumes are detected, the cause should be located and corrected.
.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors ............................... 7 9 ▫ Inside Day/Night Mirror ................. 7 9 ▫ Automatic Dimming Mirror — If Equipped .... 7 9 ▫ Outside Mirrors ....................... 8 0 ▫ Exterior Mirrors Folding Featur e — If Equipped .
▫ Manual Lumbar Support Adjustment — If Equipped ........................... 1 0 7 ▫ Adjustable Head Restraints — Front Seating Positions ........................... 1 0 7 ▫ 6 - W ay Power Seat Adjuster — Driver’s Side Only .............
▫ T o Set At A Desir ed Speed ............... 1 2 2 ▫ T o Deactivate ........................ 1 2 2 ▫ T o Resume Speed ..................... 1 2 2 ▫ T o V ary The Speed Setting ............... 1 2 3 ▫ T o Accelerate For Passing .............
▫ Erasing HomeLink Buttons .............. 1 3 6 ▫ Reprogramming a Single HomeLink Button . . . 137 ▫ Security ............................ 1 3 7 䡵 Power Sunroof — If Equipped ............. 1 3 8 ▫ Express Open Featur e .................. 1 3 9 ▫ Sunroof Maintenance .
MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the r ear window . A two-point pivot system allows for horizontal and vertical adjustment of the mirror . Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of truck).
CAUTION! T o avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror . Apply the solution onto a clean cloth and wipe the mirror clean.
Electric Remote-Control Mirrors The controls for the power mirr ors are located on the driver’s door trim panel. T o adjust a mirror , turn the control wand toward the left or right mirror positions indicated. T ilt the control wand in the direction you want the mirr or to move.
W ARNING! V ehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror .
The UConnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a separate 32 name phonebook accessible only in that language. This system is driven through your Blue- tooth™ Hands-Free pr ofile cellular phone.
Headset Profile), you may not be able to use any UCon- nect™ features. Refer to your cellular service pr ovider or the phone manufacturer for details.
V oice Command T ree Refer to “V oice T ree” at the end of this section. Help Command If you need assistance at any prompt or if you want to know what your options are at any pr ompt, say ⬙ Help ⬙ following the voice on beep. The UConnect™ system will play all the options at any prompt if you ask for help.
The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing. ⬙ • When prompted, after the voice on beep, say ⬙ Pair a Phone.
Dial by Saying a Number • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Dial. ⬙ • System will prompt you to say the number you want call. • For example, you can say ⬙ 234-567-8901. ⬙ The phone number that you enter must be of valid length and combination.
Add Names to Y our UConnect™ Phonebook NOTE: Adding names to phonebook is recommended when vehicle is not in motion. • Press the “Phone” button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook New Entry . ⬙ • When prompted, say the name of the new entry .
• Y ou will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. • When prompted, r ecite the new phone number for the phonebook entry that you are editing.
• After you enter the name, the UConnect™ system will ask you which designation you wish to delete: home, work, mobile or pager . Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted. After confirmation, the phonebook entries will be de- leted.
Phone Call Features The following features can be accessed thr ough the UConnect™ system if the feature(s) ar e available on your cellular service plan. For example, if your cellular service plan provides thr ee-way calling, this feature can be accessed through the UConnect™ system.
second call is in progr ess. T o go back to the first call, refer to ⬙ T oggling Between Calls. ⬙ T o combine two calls, refer to ⬙ Conference Call. ⬙ Place/Retrieve a Call from Hold T o put a call on hold, press the ⬘ Phone’ button until you hear a single beep which will indicate that the call has been placed on hold.
Redial • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Redial. ⬙ • The UConnect™ system will call the last number that was dialed on your cellular phone. Note: this may not be the last number dialed from the UConnect™ sys- tem.
• After the ⬙ Ready ⬙ prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). • Continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be in that language.
emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. T owing Assistance If you need towing assistance, • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ T owing Assistance.
When calling a number with your UConnect™ system that normally requir es you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’V oice Recognition’ button and say the sequence you wish to enter followed by the word ⬙ Send.
Dialing Using the Cellular Phone Keypad Y ou can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measur es).
Information Service When using A T&T W ireless Service, dialing to phone number ⬙ #121, ⬙ you can access voice activated automated system to receive news, weather , stocks, traffic, etc.
Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously pair ed to the UConnect™ system that you want to use it with. • Press the ’Phone’ button to begin.
⬘ V oice Recognition’ button anytime while the list is being played and say the priority number of the phone you wish to delete. Things Y ou Should Know About Y our UConnect™ System V oice Recognition (VR) • Always wait for the beep before speaking.
• UConnect™ phonebook name tag recognition rate is optimized for the voice of the person who stored the name in the phonebook. • Y ou can say ⬙ O ⬙ (letter ⬙ O ⬙ ) for ⬙ 0 ⬙ (zero).
102 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 103 3.
104 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
W ARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.
T o lower the head restraint, depr ess the release button located at the base of the head restraint and push down on the head restraint. 6 - W ay Power Seat Adjuster — Driver’s Side Only The 6-way power seat adjuster switches are on the outboard side of the driver’s seat.
The power seat controls ar e on the outboard side of the driver’s seat cushion. Three switches contr ol the seat movement. The four-way switch in the center can be moved forward or backwar ds to get the most comfortable position.
control seat height. Change the seat angle by using the two toggle switches, tilting it up or down. Club Cab/Quad Cab Rear Seat More car go space is available by lifting up on the rear seat cushion. The Quad Cab rear seat is a 60/40 split cushion and full back.
heat level. Flashing indicator lights on the switch indicate that the Heated Seat system needs servicing. W ARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater .
Then push the safety latch lever down while lifting the grille with your right hand. It is located at the top center of the grille just left of center . Lift the hood and gas filled props will hold it open. T o prevent possible damage, do not slam the hood to close it.
LIGHTS Interior Lights Courtesy and dome lights are turned on when the fr ont doors are opened, when the dimmer contr ol (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob.
control all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the ⬙ Party ⬙ mode because it allows the doors to stay open for extended periods of time without discharging the vehi- cle’s battery .
Headlamp Delay T o aid in your exit, your vehicle is equipped with a headlamp delay that will leave the headlamps on for 60 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off.
T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. T o remove r oad dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.
CARGO Light — If Equipped The cargo lights ar e turned on by pressing on the CARGO button. The interior lights will also turn on when the cargo lights ar e on. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature.
The arrow on either side of the instr ument cluster flashes to indicate the direction of the turn, and pr oper operation of the front and r ear turn signal lights. If an indicator fails to light when the lever is moved, it would suggest that the switch or indicator lamp is defective.
Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever . T urn the end of the handle to select the desired wiper speed.
NOTE: If the front wiper is operating when the ignition is turned off, the wiper will automatically r eturn to the ⬙ Park ⬙ position. When the vehicle is restarted, the wipers will resume operation. Windshield W ashers T o use the washer , push in on the washer knob on the end of the multifunction control lever and hold while spray is desired.
W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.
T o Set At A Desired Speed When the vehicle has reached the desir ed speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. T o Deactivate A soft tap on the brake pedal, normal braking, or pressing the CANCEL button will deactivate speed control with- out erasing the memory .
T o V ary The Speed Setting When the speed control is on, speed can be incr eased by pressing and holding the ACCEL button. When the button is released, a new set speed will be established. T apping the ACCEL button once will result in a speed increase (r efer to the table below for the speed for your specific engine).
T o Accelerate For Passing Depress the accelerator as you would normally . When the pedal is released, the vehicle will r eturn to the set speed. NOTE: When driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed.
OVERHEAD CONSOLE The overhead console has the following featur es: • Courtesy Lights • Garage Door Opener — If Equipped • Compass/T emperature Mini-T rip Computer — If Equipped Courtesy/Reading Lights Near the front of the console ar e two courtesy/reading lights.
COMP ASS/TEMPERA TURE MINI-TRIP COMPUTER This feature allows you to choose between a compass/ temperature display and one of four trip conditions being monitored. US/M Button Use this button to change the display from U.S. to metric measurement units.
Global Reset If the RESET button and STEP button ar e pressed at the same time and held for 3 seconds the Global Reset feature will reset the distance to empty (using a default fuel economy value), fuel economy , trip odometer , and elapsed time displays.
A verage Fuel Economy (A VG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset incr eases.
C/T Button Use this button to select a readout of the outside tem- perature and one of eight compass headings that indicate the direction in which the vehicle is facing. Compass/T emperature Display W ARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy , particularly in woods or on bridges.
After completing one 360° turn, with the vehicle traveling less than 5 mph (8 km/h), in an area fr ee from lar ge metal or metallic objects, the CAL symbol will turn off and the compass will function normally .
T o set the variance: T urn the ignition ON and set the display to “Compass/T emperature.” Pr ess and hold the RESET button approximately five seconds. The last vari- ance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
GARAGE DOOR OPENER — IF EQUIPPED The HomeLink 威 Universal T ransceiver replaces up to three r emote controls (hand held transmitters) that oper - ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button.
W ARNING! V ehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver . Exhaust gas can cause seri- ous injury or death. W ARNING! Y our motorized door or gate will open and close while you are training the Universal T ransceiver .
2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light in view . 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held trans- mitter buttons.
If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with ⴖ Program- ming ⴖ steps 6-8 to complete the programming of a r olling code equipped device (most commonly a garage door opener).
If you live in Canada or you are having dif ficulties programming a gate operator by using the ⬙ Pr ogram- ming ⬙ procedur es (regar dless of where you live), replace ⴖ Programming HomeLink ⴖ .
Reprogramming a Single HomeLink Button T o program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Pr ess and hold the desired HomeLink button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds.
HomeLink 威 is a trademark owned by Johnson Controls, Inc. POWER SUNROOF — IF EQUIPPED The sunroof contr ol is located on the headliner between the sun visors. Press and hold the switch r earward to fully open the sunroof. The sunr oof can be stopped at any position between closed and full open.
Press and hold the “V” button in the center of the sunr oof switch to open the vent. The sunroof can be stopped at any position between closed and full vent.
W ARNING! • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. Y ou could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. • Do not allow small children to operate the sun- roof.
The instrument panel outlet can be r econfigured by the customer to operate only when the ignition is On (switch battery fed) or with the ignition switch On/Off (battery fed) to allow for cellular phone charging and/or opera- tion while the ignition is Off.
FLOOR CONSOLE — IF EQUIPPED Floor Console Features The Floor Console between the driver’s and front pas- senger’s seat has the following features: • Miscellaneous storage compartments • Flex.
Power Outlet and Portable Phone Storage The console is equipped with a power outlet, portable phone storage bin, and phone cord r outing. The phone storage bin can be used when easy access to the phone is needed. Also, the power outlet inside console compart- ment can be used to charge the phone while it is being stored in the bin.
CUP HOLDERS If your vehicle has bucket seats with a center console, there ar e three cup holders located on the console. Refer to the section on floor console. A two-cavity cup holder is available on all Quad Cab with rear seats mounted on the floor .
T AILGA TE REMOV AL T o simplify mounting a camper unit with an overhang, the tailgate can be removed quickly . Follow these steps: 1. Open the tailgate to a 45° angle.
refer to the Consumer Information T ruck-Camper Load- ing document located in your Owner’s Manual packet or available from your dealer . For safety reasons, follow all instructions on this important document.
INSTRUMENT P ANEL AND CONTROLS CONTENTS 䡵 Instruments And Contr ols ................. 1 5 0 䡵 Instrument Cluster ...................... 1 5 1 䡵 Instrument Cluster Description ............. 1 5 2 䡵 Radio Reception Information ............... 1 5 9 ▫ AM Reception .
䡵 Sales Code RAQ – AM/FM/CD (6-Disc) Radio W ith Optional Satellite Radio, Hands Free Phone, And V ehicle Entertainment Systems (VES) Capabilities ........................... 1 6 8 ▫ Operating Instructions - Radio Mode ....... 1 6 8 ▫ Operation Instructions - (CD Mode For CD Audio Play) .
▫ CD Player .......................... 1 8 7 䡵 Compact Disc Maintenance ................ 1 8 8 䡵 Radio Operation And Cellular Phones ........ 1 8 8 䡵 Climate Controls ....................... 1 8 9 ▫ Air Conditioning And Heater ............. 1 8 9 ▫ Operating T ips .
INSTRUMENTS AND CONTROLS 150 INSTRUMENT P ANEL AND CONTROLS.
INSTRUMENT CLUSTER INSTRUMENT P ANEL AND CONTROLS 151 4.
INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. 2. T emperature Gauge The temperature gauge indicates engine coolant temperature. Any r eading within the normal range indicates that the cooling system is operat- ing satisfactorily .
left/right turn signal is left on with the engine RPM vehicle speed greater than 15 mph (24 km/h) for mor e than one mile. 4. Low Fuel W arning Light This indicator lights when the fuel gauge reads 1/8 of a tank or less. There is a pointer on the side of this symbol that indicates the side that your fuel filler door is located.
CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature light is on, safely pull over and stop the vehicle. Idle the vehicle in neutral with the air conditioner turned off until the light turns off. If the if the light remains on, turn the engine off immediately , and call for service.
12. ABS W arning Light This light monitors the Anti-Lock Brake System which is described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for approximately 3 seconds.
If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, GASCAP will be displayed in the instr ument cluster . T ighten the fuel filler cap properly and press the odom- eter reset button to turn the GASCAP message off.
light stays on, it may be an indication that the parking brake has not been released, or ther e is a low brake fluid level. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir , it indicates a possible brake hydraulic system malfunction.
CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and driveability . If the MIL is flashing, severe catalytic converter damage and power loss will soon occur . Immediate service is required.
30. 4LOCK Indicator Indicates transfer case is in 4LOCK position. 31. Odometer/T rip Odometer Button Press this button to toggle between the odometer and the trip odometer display .
display . On the AM/FM/CD (single-disc) radio only one of the two, time or frequency is displayed. Clock Setting Procedure 1. Pr ess and hold the time button until the hours blink. 2. Adjust the hours by turning the right side T une / Audio control. 3.
Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Press the ON/VOL contr ol to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio.
NOTE: In Hands Free Phone (if equipped) mode, the MUTE button mutes the microphone. SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to sear ch for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next.
TUNE Control (Radio Mode) T urn the right side rotary contr ol clockwise to increase or counter-clockwise to decr ease the frequency . AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the T one, Balance, and Fade Press the r otary TUNE control and BASS will be dis- played.
selected within 5 seconds after pressing the SET button, the station will continue to play but will not be stored into push-button memory . Y ou may add a second station to each push-button by repeating the above pr ocedure with this exception: Pr ess the SET button twice and SET 2 will show in the display window .
• If you insert a disc with the ignition ON and the radio OFF , the CD will automatically be pulled into the CD Player . • This radio does not play discs with MP3 tracks. SEEK Button (CD Mode) Press the right side of the SEEK button for the next track on the CD.
RND/SET Button (Random Play Button) (CD Mode) Press this button while the CD is playing to activate Random Play . This feature plays the selections on the compact disc in random order to pr ovide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound fr om the speakers. ⬙ MUTE ⬙ will be displayed. Press the MUTE button a second time and the sound from the speakers will return. Rotating the volume contr ol or turning OFF the ignition will also return the sound fr om the speakers.
Operating Instructions - Satellite Radio — If Equipped Refer to the Satellite Radio section of the Owner’s Manual. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SA TELLITE RADIO, HANDS .
Power Switch/V olume Control (Rotary) Press the ON/VOL contr ol to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic V olume Control The electronic volume contr ol turns continuously (360 degrees) in either dir ection without stopping.
SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to sear ch for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. T o stop the search, pr ess SCAN a second time.
AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the T one, Balance, and Fade Press the r otary TUNE control and BASS will display . T urn the TUNE control to the right or left to incr ease or decrease the Bass tones. Press the r otary TUNE control a second time and MID will display .
T oggle the PTY button to select the following format types: Program T ype 16 Digit-Character Display No program type or undefined None Adult Hits Adult_Hits Alert Alert Alert Alert Classical Classica.
By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program T ype) mode, the PTY mode will be exited and the radio will tune to the preset station.
Operation Instructions - (CD MODE for CD Audio Play) NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: Note: This Radio is capable of playing compact discs (CD), .
SEEK Button (CD MODE for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the curr ent selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Radio display will show ⬙ EJECTING DISC ⬙ when the disc is being ejected and prompt the user to r emove the disc. Press and hold the LOAD/ EJT button for 5 seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
RND/PTY Button (Random Play Button) (CD MODE for CD Audio Play) Press this button while the CD is playing to activate Random Play . This feature plays the selections on the compact disc in random order to pr ovide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
• Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙ . ⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙ . ⬙ and a 3-character extension) Multisession disc formats are supported by the radio.
MPEG Specification Sampling Frequency (kHz) Bit rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio Layer 3 24, 22.05, 16 160, 128, 144, 1 12, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 T ag information for artist, song title and album title are supported for version 1 ID3 tags.
Operation Instructions - (CD Mode for MP3 Audio Play) SEEK Button (CD Mode for MP3 Play) Pressing the right side of the SEEK button plays the next MP3 File. Pressing the left side of the SEEK button plays the beginning of the MP3 file. Pressing the button within the first ten seconds plays the previous file.
MSG or INFO Button (CD Mode for MP3 Play) Press and MSG or INFO button while playing MP3 disc. The radio scrolls thr ough the following T AG information: Song T itle, Artist, File Name, and Folder Name (if avail- able). Press the MSG or INFO button once mor e to return to ⬙ elapsed time ⬙ priority mode.
Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. Operating Instructions - V ideo Entertainment System (VES 威 ) (If Equipped) Refer to separate V ideo Entertainment System (VES 威 ) Guide.
Electronic Serial Number/Sirius Identification Number (ESN/SID) The Electronic Serial Number/Sirius Identification Num- ber is needed to activate your Sirius Satellite Radio system.
Selecting Satellite Mode in REF , RAQ, and RAK Radios Selecting Satellite Mode — REF Radio Press the MODE button r epeatedly until the word ⬙ SA T ⬙ appears in the display .
Storing and Selecting Pre-Set Channels In addition to the 12 AM and 12 FM pre-set stations, you may also commit 12 satellite stations to push button memory . These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations.
Reception Quality Satellite reception may be interr upted due to one of the following reasons. • The vehicle is parked in an undergr ound parking structur e or under a physical obstacle. • Dense tree coverage may interr upt reception in the form of short audio mutes.
The right hand control is a r ocker type switch with a push button in the center . Pressing the top of the switch will increase the volume and pr essing the bottom of the switch will decrease the volume. The button located in the center of the right hand control will switch modes to Radio or CD.
COMP ACT DISC MAINTENANCE T o keep the compact discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge.
CLIMA TE CONTROLS The controls for the heating, ventilation and air condi- tioning system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desir ed interior conditions.
The mode control (at the right of the control panel) can be set in any of the following positions: NOTE: T o improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots.
the windshield, and the demister outlets located at the edge of each side of the instrument panel. Blower Control The rotary knob on the left of the control panel is the blower control. T urn the knob clockwise to one of the four positions to obtain the blower speed you desire.
Side window demisters direct air flow specifically to the window glass to help prevent interior fogging of the glass. They are located in the extr eme outside upper edges of the instrument panel. The demisters also pr o- vide extra air ducts for circulation.
and blower speed to maintain comfort. High blower speeds will reduce fogging. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigar ette smoke, perfumes, etc.
Operation Tips Chart 194 INSTRUMENT P ANEL AND CONTROLS.
REAR WINDOW DEFROSTER – IF EQUIPPED CAUTION! Use care when washing the inside of the rear win- dow to prevent damage to heating elements. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Also, keep all objects a safe distance from the window to prevent damaging the heating elements.
.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es ..................... 2 0 1 ▫ Manual T ransmission .................. 2 0 1 ▫ Automatic T ransmission ................ 2 0 1 ▫ Normal Starting ...................... 2 0 2 ▫ Engine Block Heater — If Equipped .
䡵 Brake System .......................... 2 2 5 ▫ Rear Wheel Anti-Lock Brake System — (If Equipped) ................ 2 2 5 ▫ Four-Wheel Anti-Lock Brake System — If Equipped .................. 2 2 6 䡵 Power Steering ........................
䡵 Fuel Requirements ...................... 2 5 0 ▫ Reformulated Gasoline ................. 2 5 1 ▫ Gasoline/Oxygenate Blends .............. 2 5 1 ▫ MMT In Gasoline ..................... 2 5 2 ▫ Materials Added T o Fuel ................ 2 5 2 ▫ Adding Fuel .
▫ Recreational T owing 4WD Models ......... 2 7 4 䡵 T raction ............................. 2 7 8 䡵 Equipment Identification Plate ............. 2 7 9 200 ST ARTING AND OPERA TING.
ST ARTING PROCEDURES The starter should not be operated for more than 15 second intervals. W aiting a few seconds between such intervals will protect the starter fr om overheating. Manual T ransmission Apply the parking brake, place the gearshift control lever in NEUTRAL and depr ess clutch pedal to the floor before starting the vehicle.
Normal Starting Normal starting of either a warm or cold engine is obtained without pumping or depressing the accelerator pedal. T urn the key to the ST AR T position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the starting pr ocedure.
W ARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire, causing serious personal injury . After Starting The idle speed is automatically controlled on fuel injected engines and will decrease as the engine warms up.
W ARNING! Remember to disconnect the cord before driving. Damage to the 1 10-1 15 volt electrical cord could cause electrocution. AUTOMA TIC TRANSMISSION Automatic T ransmission The electronic PRNDL on the instrument cluster indicates the transmission gear selected.
W ARNING! Y our vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without first pulling the lever toward you, after you have set it in P (Park). Make sure it is in Park before leaving the vehicle.
“N” Neutral Shift to Neutral when vehicle is standing for prolonged periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle.
• transmission has reached normal operating tempera- ture. NOTE: If the vehicle is started in extremely cold tem- peratures, the transmission may not shift into Over drive and will automatically select the most desirable gear for operation at this temperature.
performance and reduce the potential for transmission overheating or failur e due to excessive shifting. When operating in “TOW/HAUL” mode, 5th gear (if equipped) is disabled and 2-3 and 3-4 shift patterns are modified.
transmission into gear may seem sluggish. This is due to the fluid partially draining from the tor que converter into the transmission. This condition is normal and will not cause damage to the transmission. The torque converter will refill within five seconds of shifting fr om Park into any other gear position.
Never drive with your foot resting on the clutch pedal, or attempt to hold the vehicle on a hill with the clutch pedal partially engaged, as this will cause abnormal wear on the clutch. Recommended Shift Speeds T o use your manual transmission for fuel economy it should be upshifted as listed below .
CAUTION! When descending a hill, be very careful to downshift one gear at a time to prevent overspeeding the engine which can cause valve damage. FOUR-WHEEL DRIVE OPERA TION NV233/243 GII T ransfer Ca.
NOTE: The transfer case Neutral (N) position is to be used for recr eational towing only . See Recreational T ow- ing section for specific procedur es on shifting into and out of Neutral (N). T ransfer Case Position Indicator Lights T ransfer case position indicator lights are located on the instrument cluster .
NOTE: Do not attempt to make a shift while only the front or r ear wheels are spinning. The NV233/243 trans- fer case is not equipped with a synchronizer and ther e- fore the fr ont and rear driveshaft speeds must be equal for the shift to take place.
4HI 4 Wheel Drive High Range - Locks the front and r ear driveshafts together . Forces the fr ont and rear wheels to rotate at the same speed. Additional traction for loose or slippery road surfaces only . 4LO 4 Wheel Drive Low Range - Low speed 4 wheel drive.
return the contr ol knob back to the original position, make certain all shift requir ements have been met, wait five (5) seconds and try the shift again. 2WD to 4HI or 4HI to 2WD Rotate the 4WD Control Switch to the desir ed position. Shifts between 2WD and 4HI can be done with the vehicle stopped or in motion.
3. While still r olling, rotate the transfer case control switch to the desired position. 4. After the desir ed position indicator light is ON (not flashing), shift transmission back into gear (release clutch on manual transmissions). Alternate Procedure 1.
The NV244 transfer case provides 4 mode positions - Normal all wheel drive high range, 4 wheel drive high range, 4 wheel drive low range, and neutral. This transfer case is equipped with an inter-axle.
flashing the transfer case position is all-wheel drive (A WD). If an indicator light is on, the desired position (4HI or 4LO) has been met. If One or More Shift Requirements are not Met 1. An indicator light will flash until conditions ar e met. 2. The transfer case will not shift.
When operating your vehicle in 4LO, the engine speed is approximately thr ee times that of the A WD or 4HI positions at a given road speed. T ake care not to over- speed the engine and do not exceed 25 mph (40 km/h). Proper operation of 4 wheel drive vehicles depends on tires of equal size, type and cir cumference on each wheel.
4HI 4 Wheel Drive High Range - Locks the transfer case inter-axle dif ferential. For ces front and rear wheels to rotate at the same speed. Additional traction for loose or slippery road surfaces only . 4LO 4 Wheel Drive Low Range - Low speed 4 wheel drive.
return the contr ol knob back to the original position, make certain all shift requir ements have been met, wait five (5) seconds and try the shift again. A WD to 4HI or 4HI to A WD Rotate the 4WD Control Switch to the desir ed position. Shifts between A WD and 4HI can be done with the vehicle stopped or in motion.
2. Shift the transmission into NEUTRAL (depress clutch on manual transmissions). 3. Ensur e ignition key is in the ON position with the engine either RUNNING or OFF . While still rolling, rotate the transfer case contr ol switch to the desired position.
LIMITED-SLIP REAR AXLE DIFFERENTIAL— IF EQUIPPED The limited-slip differ ential provides additional traction on snow , ice, mud, sand and gravel. It improves traction when there is a dif ference between the characteristics of the surface under the right and left rear wheels.
P ARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. T o release the parking brake, pull the parking brake release handle. Be sure the parking brake is firmly set when parked and the gear-shift lever is in the P ARK position.
W ARNING! • Always fully apply the parking brake when leav- ing your vehicle, or the vehicle may roll and cause damage or injury . Also be certain to leave an automatic transmission in Park. Failure to do so may cause the vehicle to roll and cause damage or injury .
The system remains operational in the four -wheel drive mode. The level of performance is reduced when the front brakes ar e locked up. This will cause the rear brakes to lock-up through the drivetrain, which may r educe the effectiveness of the anti-lock system.
W ARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer . Just press firmly on your brake pedal when you need to slow down or stop.
When you are in a sever e braking condition involving use of the Anti-lock Brake System, you will experience some pedal drop as the vehicle comes to a stop. This is the result of the system r everting to the base brake system. Engagement of the Anti-lock Brake System may be accompanied by a pulsing sensation.
W ARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible.
TIRE SAFETY INFORMA TION Tire Markings NOTE: • P (Passenger)-Metric tir e sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tir e sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger car tire based on Eur opean design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressur e is listed on either the face of the driver’s door or the driver’s side “B” pillar .
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loadi.
4. The r esulting figure equals the available amount of cargo and luggage load capacity . For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb.
ST ARTING AND OPERA TING 237 5.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Underinflation also increases tir e rolling r esistance and results in higher fuel consumption.
CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard ar e always “cold tire inflation pr essure”.
loading may be requir ed for high speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pr essures. W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous.
Compact Spare Tire — If Equipped The compact spare is for temporary emer gency use with radial tires. It is engineer ed to be used on your style vehicle only . Since this tire has limited tread life, the original tire should be r epaired (or r eplaced) and rein- stalled at the first opportunity .
Limited Use Spare — If Equipped The limited use spare tir e is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tir e warning label located on the limited use spare tire and wheel assembly . This tire may look like the original equipped tire on the fr ont or rear axle of your vehicle, but it is not.
W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck.
Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and spare tire should be replaced after six years, regardless of the remaining tread.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle.
Improper alignment will not cause vehicle vibration. V ibration may be a result of tire and wheel out-of- balance. Proper balancing will r educe vibration and avoid tire cupping and spotty wear .
CAUTION! T o avoid damage to your vehicle, tires or chains, observe the following precautions: • Because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious vehicle damage.
SNOW TIRES Snow tires should be of the same size and type constr uc- tion as the front tir es. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requir ement associated with the tire. These tir es should always be operated at the vehicle maximum capacity inflation pressur es under any load condition.
Section of this manual. More fr equent rotation is permis- sible if desired. The r easons for any rapid or unusual wear should be corrected prior to r otation being per- formed.
Over 40 auto manufacturers world-wide have issued and endorsed consistent gasoline specifications (the W orld- wide Fuel Charter , WWFC) to define fuel properties necessary to deliver enhanced emissions, performance and durability for your vehicle. W e recommend the use of gasolines that meet the WWFC specifications if they are available.
MMT In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasolines blended with MMT provide no performance advantage beyond gasolines of the same octane number without MMT . Gasolines blended with MMT reduce spark plug life and reduce emission system performance.
ADDING FUEL NOTE: If fuel is poured fr om a portable container , the container should have a flexible nozzle long enough to extend into the fuel filler tube. CAUTION! T o avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling.
W ARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle or on a truck bed. Y ou could be burned. Always place gas containers on the ground while filling. Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door .
Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law .
Carbon Monoxide W arnings W ARNING! Carbon monoxide (CO) in exhaust gases is deadly . Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill.
CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly .
VEHICLE LOADING Certification Label As requir ed by National Highway T raffic Safety Admin- istration Regulations, your vehicle has a certification label affixed to the driver’s side door .
Gross Axle W eight Rating (GA WR) The GA WR is the maximum permissible load on the front and rear axles. The load must be distributed in the car go area so that the GA WR of each axle is not exceeded. Each axle GA WR is determined by the component in the system with the lowest load carrying capacity (axle, springs, tires, or wheels).
then be determined separately to be sure that the load is properly distributed over fr ont and rear axle. W eighing the vehicle may show that the GA WR of either the front or rear axles has been exceeded but the total load is within the specified GVWR.
after the vehicle has been weighed both in its ⴖ curb weight ⴖ condition, and in its ⴖ loaded and ready for operation ⴖ condition. Gross V ehicle W eight Rating (GVWR) 6500 LBS. TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
Gross T railer W eight (GTW) The gross trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙ loaded and ready for operation ⬙ condition.
Frontal Area The maximum height and maximum width of the front of a trailer . T railer Sway Control The trailer sway control is a telescoping link that can be installed between the hitch receiver and .
T railer Hitch Classification The rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment. Y our vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional T railer T ow Prep Package.
T railer T owing Weights (Maximum T railer Weight Ratings) NOTE: For additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • http:// www .dodge.com/towing . • http:// www .dodge.ca (Canada).
• The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
W ARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
2. GTW 3. GA WR 4. T ongue weight rating for the trailer hitch utilized (This requir ement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). T owing Requirements — T ires − Do not attempt to tow a trailer while using a compact spare tir e.
actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electr onic brake controller is not r equired. − T railer brakes are r ecommended for trailers over 1,000 lbs (454 kg) and requir ed for trailers in excess of 2,000 lbs (907 kg).
NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector . Refer to the following illustrations. T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away fr om heavy traffic.
If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage. T owing T ips — Automatic T ransmission The “D” range can be selected when towing. However , if frequent shifting occurs while in this range, the “T OW HAUL” or “OD/OFF” range should be selected.
T owing T ips — Cooling System T o reduce potential for engine and transmission over - heating, take the following actions: − City Driving When stopped for short periods of time, put transmission in neutral and increase engine idle speed. − Highway Driving Reduce speed.
W ARNING! Snowplows, winches, and other aftermarket equip- ment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end structure. The airbags could deploy unexpectedly or could fail to deploy during a collision resulting in serious injury or death.
Recreational T owing 4WD Models CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing. CAUTION! The transfer case must be shifted into Neutral (N) for recreational towing. The Neutral (N) selection but- ton is located on the lower left hand corner of the 4WD Control Switch.
CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in Neutral (N) before recreational towing to prevent damage to internal parts. 1. Bring vehicle to a complete stop. 2. Shut engine OFF . 3. Place ignition key in the ON position.
NOTE: Items 1 through 5 ar e requir ements that must be met prior to depressing the Neutral (N) selection button, and must continue to be met until the 4 seconds elapses and the shift has been completed.
5. Depr ess brake pedal. 6. Shift automatic transmission to Neutral (N) or depr ess clutch on manual transmission. 7. Using the point of a ballpoint pen or similar object, depress the r ecessed transfer case Neutral (N) button for 1 second. 8. After the Neutral (N) indicator light turns of f release the Neutral (N) button.
W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake.
2. Slow down if r oad has standing water or puddles. 3. Replace tir es when tread wear indicators first become visible. 4. Keep tir es properly inflated. 5. Maintain suf ficient distance between your vehicle and the car in front to avoid a collision in a sudden stop.
.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher .................. 2 8 2 䡵 Adding Fuel .......................... 2 8 2 䡵 Changing A Flat T ire .................... 2 8 4 ▫ Jack Location ........................ 2 8 4 ▫ Removing The Spare T ire .
HAZARD W ARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and r ear directional signals will flash intermittently . Press the switch a second time to turn of f the emergency flashers.
W ARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed. Y ou could be burned. Always place gas contain- ers on the ground while filling. W ARNING! Remove the gas cap slowly to prevent fuel spray from the filler neck which may cause injury .
CHANGING A FLA T TIRE Jack Location In the Dakota, the scissor jack and tire changing tools for Club Cab models are stowed in a compartment under the rear passenger seat. Quad Cab model scissor jack and tir e changing tools are accessed by lifting up the r ear passen- ger seat.
Jack Stowage Location Extended Cab Jack Stowage Location Double Cab WHA T TO DO IN EMERGENCIES 285 6.
W ARNING! The jack is designed as a tool for changing tires only . The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure. The vehicle should be jacked on a firm level surface only .
Inserting Lug W rench and Extension T urning Lug W rench and Extension WHA T TO DO IN EMERGENCIES 287 6.
It is recommended that you stow the flat or spar e to avoid tangling the loose cable. NOTE: The winch mechanism is designed for use with the jack extension tube only . Use of an air wrench or other power tools is not recommended and can damage the winch.
Preparations Park the vehicle on a firm level surface, avoiding ice or slippery areas. Set the parking brake and place the gear selector in P ARK (automatic transmission). On Four Wheel Drive vehicles, shift the transfer case to the “4L” position.
to inboard transition, as shown. Operate the jack using the jack drive tube and the wheel wrench - the tube extension, may be used but is not requir ed. When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 4. By r otating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface.
Correct nut tightness is the following: • Steel Wheels: 130-170 ft. lbs. (177-231 N·m) torque. • Aluminum Wheels: 120-160 ft. lbs. (163-217 N·m) torque. W ARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle.
T o Stow The Flat Or Spare T urn the wheel so that the valve stem is down. Slide the wheel retainer thr ough the center of the wheel and position it properly acr oss the wheel opening. For convenience in checking the spare tir e inflation, stow with the valve stem toward the r ear of the vehicle.
Check the Battery T est Indicator (if equipped). If a light or bright colored dot is visible in the indicator (if equipped), DO NOT jump-start the battery .
W ARNING! Do not connect the cable to the negative post of the discharge battery . The resulting electrical spark could cause the battery to explode. During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze.
EMERGENCY T OW HOOKS — IF EQUIPPED Y our vehicle may be equipped with emergency tow hooks. W ARNING! Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. W ARNING! Stand clear of vehicles when pulling with tow hooks.
CAUTION! T ow hooks are for emergency use only , to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. Y ou could damage your vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is r equired to pr event damage to your vehicle.
If the vehicle is to be towed more than 15 miles (25 km ) or faster than 30 mph, it must be towed on a flatbed, or with the rear wheels raised and the fr ont wheels on the ground, or with the fr ont end raised and the rear wheels on a towing dolly .
MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment 3.7L V6 .............. 3 0 2 䡵 Engine Compartment 4.7L/4.7HO V -8 ........ 3 0 3 䡵 Onboard Diagnostic System — OBD II ........ 3 0 4 ▫ Loose Fuel Filler Cap Message ............ 3 0 4 䡵 Emissions Inspection And Maintenance Programs .
▫ Air Conditioner Maintenance ............. 3 1 6 ▫ Power Steering — Fluid Check ............ 3 1 7 ▫ Front Suspension Ball Joints .............. 3 1 7 ▫ Drive Shaft Constant V elocity Joints ........ 3 1 8 ▫ Body Lubrication .............
▫ Center High-Mounted Stoplamp And Cargo Lamp .............................. 3 5 0 ▫ License Lamps ....................... 3 5 3 ▫ Fog Lamps .......................... 3 5 4 䡵 Fluids And Capacities ................... 3 5 5 䡵 Fluids, Lubricants And Genuine Parts .
ENGINE COMP ARTMENT 3.7L V6 302 MAINT AINING YOUR VEHICLE.
ENGINE COMP ARTMENT 4.7L/4.7HO V -8 MAINT AINING YOUR VEHICLE 303 7.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
cap until a ⬙ clicking ⬙ sound is heard. This is an indication that the gas cap is properly tightened. Pr ess the odometer reset button to turn the message of f. If the problem persists, the message will appear the next time the vehicle is started.
3. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 4. Appr oximately 15 seconds later , one of two things will happen: a. The MIL light will blink for approximately 5 sec- onds and then remain on until the first engine crank or the key is turned off.
DEALER SERVICE Y our dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner . Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any pr ocedure yourself.
1. Position the vehicle on a level surface. 2. T urn Off the engine and allow appr oximately 5 min- utes for the oil to settle to the bottom of the crankcase. 3. Remove the engine oil level indicator (dipstick). 4. W ipe the engine oil level indicator (dipstick) clean.
Frequency Of Oil Change Road conditions and your style of driving affect the interval at which your oil should be changed. Check the following to determine if ANY apply to you: • Day or night temperatures ar e below 32°F (0°C). • Stop and Go driving.
should also be checked periodically . Make sure that these units are always clean. This will tend to r educe to a minimum the amount of abrasive material that may enter the engine.
Lubricants which do not have both, the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used. Synthetic Engine Oils There ar e a number of engine oils being promoted as either synthetic or semi-synthetic.
Drive Belts — Check Condition and T ensioner Belt tension is controlled by means of an automatic tensioner . No belt tension adjustments are r equired. However , belt and belt tensioner condition should be inspected at the specified intervals, and replaced if r e- quired.
Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”. If, however , you drive the vehicle frequently under dusty or sever e con- ditions, the filter element should be inspected periodi- cally and replaced if necessary at the intervals shown on Schedule “B”.
CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly .
T o minimize the possibility of catalyst damage: • Do not shut off the engine or interr upt the ignition when the transmission is in gear and the vehicle is in motion.
CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case.
Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluor ocar- bon (HFC) that is endorsed by the Environmental Pr o- tection Agency and is an ozone-saving product.
Drive Shaft Constant V elocity Joints All four wheel drive models are equipped with four constant velocity joints. Periodic lubrication of these joints is not requir ed. However , the joint boot should be inspected for external leakage or damage periodically .
A void using the wiper blades to remove fr ost or ice from the windshield. Keep the blade rubber out of contact with petroleum pr oducts such as engine oil, gasoline, etc. Windshield W ashers The fluid reservoir should be checked for fluid level at regular intervals.
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, .
Check the coolant bottle tubing for condition and tight- ness of connection at coolant bottle and radiator . Inspect the entire system for leaks. W ARNING! Y ou or others can be badly burned by hot coolant or steam from your radiator . If you see or hear steam coming from under the hood don’t open the hood until the radiator has had time to cool.
children. If ingested, contact a physician or poison con- trol specialist in your ar ea. Clean up any ground spills immediately . Recommended Engine Coolant This vehicle has been factory filled with an Ethylene Glycol based engine coolant with long life corrosion inhibitors (called HOA T , for Hybrid Organic Additive T echnology).
Adding Coolant When adding coolant, or refilling the system, a minimum solution of 50% recommended HOA T ethylene glycol engine coolant (antifreeze) and distilled water should be used. Use higher concentrations (not to exceed 70%) if temperatures below ⫺ 34°F ( ⫺ 37°C) ar e anticipated.
W ARNING! The warning words “DO NOT OPEN HOT” on the coolant pressure cap are a safety precaution. Heat causes pressure to build up in the cooling system. T o prevent scalding or injury , do not remove the pres- sure cap when the system is hot or under pressure.
E. Make sur e that the radiator and coolant bottle over- flow hoses are not kinked or obstr ucted. F . Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean also. G. The thermostat should not be changed for summer or winter operation.
PCV valve and passage with increasing mileage. Have the PCV valve, hoses, and passages checked for proper operation at the intervals specified. If the valve is plugged or sticking, replace with a new valve – Do not attempt to clean the oil PCV valve! Check ventilating hose for indication of damage or plugging with deposits.
W ARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from for eign matter or moisture.
W ARNING! W orn brake hoses can burst and cause brake failure. Y ou could have an accident. If you see any sign of cracking, scuffing, or worn spots, have the brake hoses replaced immediately . Clutch Hydraulic System The clutch hydraulic system is a sealed maintenance free system.
3. Fully apply the parking brake and press the brake pedal. 4. Place the gear selector momentarily in each gear position ending with the lever in P (Park). 5. Remove the dipstick, wipe it clean and r einsert it until seated. 6. Remove the dipstick again and note the fluid level on both sides.
dipstick cap is properly r eseated. It is normal for the dipstick cap to spring back slightly from its fully seated position, as long as its seal remains engaged in the dipstick tube.
T ransfer Case Inspect the transfer case for fluid leaks. If a fluid leak is evident the transfer case fluid level may be low . Have the transfer case serviced immediately . CAUTION! Damage may result from operation of the vehicle with low transfer case fluid.
axle fluid level should be 1/4 ⬙ (6.35mm) below filler plug hole for 8 1/4 ⬙ axles and should be 5/8 ⬙ (16mm) below filler plug for 9 1/4 ⬙ axles.
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body care requir ements vary according to geo- graphic locations and usage.
• A void using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder , which will scratch metal and painted surfaces.
• If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials ar e well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar 威 touch up paint on scratches as soon as possible.
Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner . Never use an abrasive type cleaner . Use caution when cleaning inside rear windows equipped with electric defrosters or windshields equipped with a windshield wiper de-icer .
POWER DISTRIBUTION CENTER (FUSE/RELA Y) Y our vehicle is equipped with an electrical power distri- bution center located on the left side of the engine compartment. These power distribution centers house new plug-in “Cartridge” fuses which replace all the in-line fusible links previously used.
Cavity Cartridge Fuse Mini Fuse Description 9 10 Amp Red Airbag System #3 10 Spare 1 1 10 Amp Red AC Clutch 12 15 Amp Blue T T ow Lt Stop/T urn 13 15 Amp Blue T T ow Rt Stop/T urn 14 20 Amp Y ellow IO.
Cavity Cartridge Fuse Mini Fuse Description 33 30 Amp Pink ASD 34 30 Amp Pink FCM2 (Ext. Light # 2) 35 40 Amp Green HV AC Blower Motor 36 10 Amp Red Ignition UNLK/ RN/ST 37 10 Amp Red Crank 38 20 Amp .
Cavity Cartridge Fuse Mini Fuse Description 57 20 Amp Y ellow Airbag System #2 58 20 Amp Y ellow Heated Seats 59 10 Amp Red HV AC Module 60 10 Amp Red ABS Module 61 20 Amp Y ellow FCM3 (Re- verse Lamps) CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
I.O.D. cavity includes a snap-in retainer that allows the fuse to be disconnected, without removing it fr om the fuse block. • The transfer case should be placed in the 4HI mode and kept in this position to minimize the battery drain. • As an alternative to the above steps you may discon- nect the negative cable from the battery .
BULB REPLACEMENT Headlamps Removing Attaching Screw Removing Headlamp Assembly 342 MAINT AINING YOUR VEHICLE.
1. Open the hood. 2. Remove the 3 scr ews attaching the headlamp housing to the inner panel. 3. Grasp the headlamp and pull firmly to disengage the headlamp housing from the fender panel. 4. While firmly holding the headlamp housing in your hands unlock and disconnect Headlamp bulb connector .
Removing Headlamp Bulb Unlocking Connector 344 MAINT AINING YOUR VEHICLE.
Removing Headlamp from Assembly Removing Headlamp Bulb MAINT AINING YOUR VEHICLE 345 7.
6. Reverse pr ocedure to install new Headlamp bulb into the headlamp assembly . NOTE: These are Halogen bulbs. T ake care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat buildup which reduces bulb life. Front Park and T urn Signal Lamp.
• Rotate bulb socket 1/4 turn and remove socket fr om housing. • Pull bulb straight from socket. • Reverse procedur e to install new turn signal bulb.
Rear Side Marker , T aillamps/Stoplamp, and T urn Signal Bulbs — Replacement 1. Remove the two (2) scr ews that pass through the bed sheetmetal. 2. Pull the taillamp housing straight out fr om the body .
3. Rotate the bulb socket fr om the housing. 4. Pull bulb straight out of socket. Rotating Bulb Socket From Housing Pulling Bulb From Socket MAINT AINING YOUR VEHICLE 349 7.
5. Reverse Pr ocedure to install bulb and housing. Place the two raised blocks passed the body . Center High-Mounted Stoplamp And Cargo Lamp 1. Remove the two (2) scr ews holding the housing/lens to the body as shown.
2. Remove housing from Cab 3. Remove connector fr om housing tab for more clear- ance. Removing Housing from Cab Removing Connector from T ab MAINT AINING YOUR VEHICLE 351 7.
4. T urn desired bulb socket 1 ⁄ 4 turn and remove socket and bulb from housing. 5. Pull desir ed bulb straight from the socket. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High Mount Sto.
6. Reverse pr ocedure for installation of bulbs and hous- ing. License Lamps 1. Using a scr ew driver pry black rubber housing from the bumper . 2. Rotate the socket 1/4 turn counter clockwise.
3. Pull bulb fr om socket. 4. Reverse pr ocedure for installation. Fog Lamps 1. Disconnect connector fr om fog lamp by raising wire harness lock tab and pulling on wire harness connector . 2. Rotate fog lamp bulb 1/4 turn counter clockwise and pull to remove fr om fog lamp housing.
FLUIDS AND CAP ACITIES U.S. Metric Fuel 3.7L/4.7L, 87 Octane 22 Gal. 83L 4.7L HO, 91 Octane, Recommended Not Required 22 Gal 83L Engine Oil (with filter) 3.7L, SAE 5W -30, API Certified 5 Qt. 4.7L 4.7L, SAE 5W -30, API Certified 6 Qt. 5.7L 4.7L HO, SAE 5W -30, API Certified 6 Qt.
FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar 威 Antifr eeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) or equivalent. Engine Oil Use SAE 5W -30, API Certified, meeting material standar d MS-6395.
Chassis Component Fluids, Lubricants and Genuine Parts. Automatic T ransmission Mopar 威 A TF+4, Automatic T ransmission Fluid. Manual T ransmission (Getrag 238) Mopar 威 A TF+4, Automatic T ransmission Fluid. T ransfer Case Mopar 威 A TF+4, Automatic T ransmission Fluid.
.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 3 6 0 䡵 Emissions T esting ....................... 3 6 0 䡵 Maintenance Schedules ................... 3 6 1 ▫ Schedule “B” ........................ 3 6 4 ▫ Schedule “A” .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages must be done at the times or mileages specified to assure the continued pr oper func- tioning of the emission control system.
MAINTENANCE SCHEDULES There ar e two maintenance schedules that show the required service for your vehicle. First is Schedule “B” . It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule.
Use the schedule that best describes your driving condi- tions. Where time and mileage ar e listed, follow the interval that occurs first. NOTE: Under no circumstances should oil change in- tervals exceed 6000 miles (10 000 km) or 6 months whichever comes first.
Once a Month • Check tire pr essure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as requir ed. • Check the fluid levels of coolant reservoir , brake master cylinder , and transmission and add as needed.
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures ar e below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions.
Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. X X XXX Rotate tires. X X Check spare tir e for proper pr essure and correct stowage.
Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. X X XXX Rotate tires. X X X Check spare tir e for proper pr essure and correct stowage.
Miles 33,000 36,000 39, 000 42,000 45,000 (Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. X X XXX Rotate tires. X X Check spare tir e for proper pr essure and correct stowage.
Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. X X XXX Rotate tires. X X X Check spare tir e for proper pr essure and correct stowage.
Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Drain and refill automatic transmission fluid, change filter (3.7L). * X Drain and refill automatic transmission fluid and change main sump filter (4.7L).
Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (105 000) (1 10 000) (1 15 000) (120 000) (125 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. XXX X Rotate tires. X X Check spare tir e for proper pr essure and correct stowage.
Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers ) (130 000) (135 000) (140 000) (145 000) (150 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. X X XXX Rotate tires. X X X Check spare tir e for proper pr essure and correct stowage.
Miles 93,000 96,000 99,000 102,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. XXX X Rotate tires. X X Check spare tir e for proper pr essure and correct stowage.
Miles 105,000 108,000 1 11,000 114,000 1 17,000 120,000 (Kilometers) (175 000) (180 000) (185 000) (190 000) (195 000) (200 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. X X XXXX Rotate tires. X X X Check spare tir e for proper pr essure and cor- rect stowage.
Miles 105,000 108,000 1 11,000 114,000 1 17,000 120,000 (Kilometers) (175 000) (180 000) (185 000) (190 000) (195 000) (200 000) Drain and refill automatic transmission fluid, change filter (3.7L). * X Drain and refill automatic transmission fluid and change main sump filter and spin-on cooler return filter if equipped.
Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [Months] [6] [12] [18] [24] [30] Change engine oil and engine oil filter . X X X X X Rotate tir es. X X X X X Check spare tir e for proper pr essure and correct stowage.
Miles 36,000 42,000 48,000 54000 60,000 66,000 (Kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) (1 10 000) [Months] [36] [42] [48] [54] [60] [66] Change engine oil and engine oil filter . X X X X X X Rotate tir es. X X X X X X Check spare tir e for proper pr essure and cor- rect stowage.
Miles 72,000 78,000 84,000 90,000 96,000 (Kilometers) (120 000) (130 000) (140 000) (150 000) (160 000) [Months] [72] [78] [84] [90] [96] Change engine oil and engine oil filter . X X X X X Rotate tir es. X X X X X Check spare tir e for proper pr essure and correct stowage.
Miles 102,000 108,000 1 14,000 120,000 (Kilometers) (170 000) (180 000) (190 000) (200 000) [Months] [102] [108] [1 14] [120] Change engine oil and engine oil filter . X X X X Rotate tir es. X X X X Check spare tir e for proper pr essure and correct stowage.
W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 3 8 2 ▫ Prepar e For The Appointment ............ 3 8 2 ▫ Prepar e A List ........................ 3 8 2 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager .
technicians, special tools, and the latest information to assure your vehicle is fixed corr ectly and in a timely manner . This is why you should always talk to your dealer’s service manager first.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center .
W ARRANTY INFORMA TION (U.S. V ehicles Only) See the W arranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer .
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover or ders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Call T oll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orld Wide W eb at: • www .techauthority .
on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perfor - mance. W ARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
INDEX 10.
Adding Fuel ........................ 253,282 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 313 Air Conditioner Maintenance ............... 3 1 6 Air Conditioning ........................ 1 8 9 Air Conditioning, Operating T ips .......... 189,192 Air Conditioning Refrigerant .
Ball Joints ............................. 3 1 7 Battery ............................... 3 1 5 Charging ............................ 2 9 3 Emergency Starting ..................... 2 9 3 Gas Caution .......................... 2 9 3 Keyless T ransmitter Replacement (RKE) .
Center High Mounted Stop Light ............ 3 5 0 Center Seat Storage Compartment ............ 1 4 3 Certification Label ....................... 2 5 8 Changing A Flat T ire ..................... 2 8 4 Charging .............................. 2 9 3 Chart, T ire Sizing .
Customer Assistance ..................... 3 8 2 Data Recorder , Event ...................... 5 5 Daytime Running Lights ................... 1 1 6 Dealer Service .......................... 3 0 7 Defroster , Rear W indow ................... 1 9 5 Defroster , W indshield .
Block Heater ......................... 2 0 3 Break-In Recommendations ................ 7 0 Compartment ......................... 3 0 3 Coolant (Antifreeze) ................. 322,356 Cooling ............................. 3 2 0 Exhaust Gas Caution .....
Fluid Capacities ......................... 3 5 5 Fluid Level Checks Automatic T ransmission ................. 3 2 8 Brake ............................... 3 2 6 Cooling System ....................... 3 2 0 Engine Oil ........................... 3 0 7 Power Steering .
Grease ............................... 3 3 2 Gross Axle W eight Rating ............... 259,262 Gross Car go W eight ...................... 2 5 8 Gross V ehicle W eight Rating ................ 2 6 1 GVWR ............................ 258,261 Hands-Free Phone (UConnect™) .
Interior Lights .......................... 1 1 3 Intermittent W ipers (Delay W ipers) ........... 1 1 9 Introduction ............................. 4 Jack Operation ....................... 284,288 Jacking Instructions ...................... 2 8 9 Key , Replacement .
License ............................. 3 5 3 Lights On Reminder .................... 1 1 6 Low Fuel ......................... 152,153 Malfunction Indicator (Check Engine) ........ 1 5 7 Passing ............................. 1 1 8 Seat Belt Reminder ...
Lubricant Selection .................. 328,357 Map/Reading Lights ..................... 1 2 5 Mirrors ................................ 7 9 Automatic Dimming ..................... 7 9 Electric Powered ....................... 8 1 Heated ................
Owner’s Manual (Operator Manual) .......... 3 8 6 Panic Alarm ............................ 2 3 Parking Brake .......................... 2 2 4 Parking On Hill ......................... 2 2 4 Passenger Airbag On/Off Switch ............. 5 4 Passing Light .
Radio, Satellite .......................... 1 8 2 Radio (Sound Systems) ................. 160,168 Rear Axle (Dif ferential) .................... 3 3 1 Rear W indow ........................... 3 0 Rear W indow Defroster ................... 1 9 5 Rearview Mirrors .
And Pregnant W omen ................... 3 9 Child Restraint ....................... 57,59 Extender ............................. 3 9 Front Seat ............................ 3 1 Inspection ............................ 7 2 Pretensioners ................
Spark Plugs ............................ 3 1 2 Speed Control (Cr uise Control) .............. 1 2 1 Speedometer ........................... 1 5 4 Starting ............................... 2 0 1 Emergency (Jump Starting) ............... 2 9 3 Engine Block Heater .
Chains .............................. 2 4 7 Changing ............................ 2 8 4 Compact Spare ........................ 2 4 2 General Information .................... 2 3 8 High Speed .......................... 2 4 0 Inflation Pressur es ......
T railer W eight .......................... 2 6 5 T ransaxle ............................. 2 0 4 Automatic ........................... 2 0 4 Operation ........................... 2 0 4 T ransfer Case ........................... 3 3 1 Fluid ...........
W eight Load Carrying .................... 2 5 8 Wheel Alignment and Balance ............... 2 4 6 Wheel and Wheel T rim .................... 3 3 4 Wheel Changing ........................ 2 8 4 Wheel Mounting ........................ 2 8 8 Wheel Nut T orque .
NOTES.
NOTES.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Dodge 2006 Dakota c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Dodge 2006 Dakota - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Dodge 2006 Dakota, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Dodge 2006 Dakota va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Dodge 2006 Dakota, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Dodge 2006 Dakota.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Dodge 2006 Dakota. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Dodge 2006 Dakota ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
