Manuel d'utilisation / d'entretien du produit WRCPF-KIT du fabricant Dimplex
Aller à la page of 20
Owner ’ s Manual Model WRCPF-KIT 72091 10100R03 IMPORT ANT SAFETY INFORMA TION: Always read this manual rst before attempting to install or use this device. For your safety , always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage.
2 www .dimplex.com T able of Contents ! NOTE: Procedures and techniques that are considered important enough to emphasize. CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the equipment.
3 W elcome & Congratulations Thank you and congratulations for choosing to purchase a W all Switch Remote Control Kit from Dimplex, the world leader in electric replaces. Please carefully read and save these instructions. CAUTION: Read all instructions and warnings carefully before starting installation.
4 www .dimplex.com Product Overview The W all Switch Remote Control Kit is designed to work with the following Dimplex electric replaces: BF33STP • BF33DXP • BF39STP • BF39DXP • BF45DXP •.
5 Receiver Installation (BF units only) Open steel curtain (remove 1. glass doors if applicable). Remove two (2) screws on l og 2. grate and remove log grate (Figure 1). Locate and remove the two (2) 4. screws on the manual control bracket (Figure 3).
6 www .dimplex.com Locate the plastic 9-pin plug 6. in the bottom corner of the replace where the manual controls were plugged in to. Insert the plug connector from 7. the remote control bracket (Figure 4) into plastic plug inside the replace. ledge (Figure 2) and the logs are resting against the partially reective glass.
7 W all Control Installation ! NOTE: All electrical w iring must comply with all national and local electrical codes and regulations. Always use a qualied and licensed electrician should you have any questions or concerns for all wiring work. ! NOTE: The W all Switch Remote Control is made to t standard Decora style faceplates.
8 www .dimplex.com Figure 5 Outer Housing Controller 2. Release the Controller from its Outer Housing by pushing the front face into the Outer Housing until you hear a click. This will release the push- lock latches and allow the Controller to be removed from the Outer Housing (Figure 5).
9 W all Control Installation to complete the installation and to blend the installation in with your choice of decor . Hard Wired Power Supplied Installation Before starting this installation, it is helpful to initialize the W all Switch Remote Control with your rebox (see Initialization section).
10 www .dimplex.com W all Control Installation 1. Unpack the W all Switch Remote Control and all hardware from its package. 2. Release the Controller from its Outer Housing by pushing the front face into the Outer Housing until you hear a click.
11 W all Control Installation Figure 12 Controller Outer Housing Figure 13 Locking Screw Option (Figure 14) T o prevent tampering, damage, and theft, it is suggested to install the locking screws.
12 www .dimplex.com W all Control Installation Figure 15 Ensure each of the two Controller lead wires are connected to separate Low V oltage 24V~ only wires.
13 ! NOTE: Wire leads are not polarized due to the nature of this device. 9. Coil excess wiring to the back of the device box and insert the Controller and Outer Housing int o t he d evi ce box (Fi gur e 16 ). Fasten with two supplied at head screws.
14 www .dimplex.com Initialization After installation, locate the section which applies to your specic model of replace and follow the steps for remote control initialization and if required, re-initialization. Refer to your replace's owner's manual to locate manual or other controls as needed.
15 Initialization DF3033ST and DFG3033 Models 1. Ensure that power is supplied through main service panel. 2. Ensure the Main On/Off Switch located in the switch box on the replace in the upper right hand corner is in the On position (Figure 19A) .
16 www .dimplex.com Operation A. On Button Pressing this button toggles sequentially through the three levels of the replace. Pressing once activates Level 1 - ame effect only , twice activates Level 2 - ame effect and Purire™, three times activates Level 3 - ame effect, Purire™ and heat.
17 Operation W all Switch Remote Control 1 3 5 2 4 6 7 9 11 8 10 12 13 14 1. Room T emperature 2. Set T emperature 3. Flame Effect 4. Purire™ 5. Heat Off Indicator 6. Function Lock Indicator 7. RF Code Function Indicator 8. Set T emperature Down 9.
18 www .dimplex.com Operation 1. Room T emperature Displays current ambient temperature in the room. 2. Set T emperature Displays and controls the heater to the temperature at which the thermostat is currently set to. Press 8 to lower the thermostat and press 9 to raise the thermostat.
19 Operation 7. RF Code Function and Change Procedure In the event that the W all Switch Remote Control does not work properly with the receiver due to interference from additional wireless signals, this function will allow the RF code to be changed. T o enable this function, press 9 and 12 together .
20 www .dimplex.com W arranty This Dimplex W all Switch Remote Control is warranted against defects in workmanship and materials for two years from date of sale.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Dimplex WRCPF-KIT c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Dimplex WRCPF-KIT - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Dimplex WRCPF-KIT, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Dimplex WRCPF-KIT va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Dimplex WRCPF-KIT, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Dimplex WRCPF-KIT.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Dimplex WRCPF-KIT. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Dimplex WRCPF-KIT ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
