Manuel d'utilisation / d'entretien du produit 01510-1030E Rev A du fabricant Dimension One Spas
Aller à la page of 54
.
.
Export Sonic Immers ion System Table of Contents OWNER’S MANU AL ......................................................................... 1 F EATURES OF THE S ON IC I MMERSION ................................................. 1 U SING THE CD P LAYER .
Export Sonic Immers ion System iv.
Export Sonic Immers ion System Dealer Owners Man ual Owner’s Manual Features of the Sonic Immersion • Dealer installation allows you to add to any Sonic Immersion System ready Dimension One Spa in stock • Patented planar magnetic speaker tech nology (1/4” [6.
Export Sonic Immers ion System Dealer Installation Guide Dealer Installation This section intend ed for use by authorized dealer person nel only 2.
Export Sonic Immers ion System Dealer Installation Guide Getting Ready To Start The Sonic Immersion System can only be installed on spas with the following serial numbers .
Export Sonic Immers ion System Dealer Installation Guide Table 2 Required Tools Electric drill 1 ½ inch (3.8 mm) hole saw ¼ inch (6.35 mm) dri ll bit 3/8 inch (9.5 m m) drill bit Saber Saw Phillips screwdriver Tape (masking, electrica l, duct, or packaging) ½ in (12.
Export Sonic Immers ion System Dealer Installation Guide Medium Size Needle Nose Pliers Wire Stripper Utility Knife 5/16” (7.94 m m) Nut Driver or wrench Six inch (15.
Export Sonic Immers ion System Dealer Installation Guide Table 3 Parts List Description Qty Item Number This document 1 01510- 1030 Amplifier 1 01564-08 Coarse- Threaded Drywall Screws 5 01051-0 6 Tem.
Export Sonic Immers ion System Dealer Installation Guide Stereo 1 01564-03 Sub-woofer sub assembly 1 01564-0 9 Stereo cover, marine 1 01564-0 4 Dual pole antenna 1 01564-0 5 Preamp stereo, cable 2 01570-2 4 Power supply screw, sheet metal, SS, PH 2 01011-3 8 Marine cover screws, #8 x ½” (1.
Export Sonic Immers ion System Dealer Installation Guide Cable Ty Mount 10 01200-005 Removing Panels In order to install the system up to three panels must be r emoved from the spa: the equipment compa r tment panel, the panel where the sub woofer is installed, and the pa nel where the Satellite Speakers are to be installed.
Export Sonic Immers ion System Dealer Installation Guide Figure 1. Top Side Control 4. The Lower Control is located in the equipment co mpartment behind the spa pane l below the Main To p Side Control. 5. Use the screwdriver to remove the equi pment compartment panel screws, Figure 2.
Export Sonic Immers ion System Dealer Installation Guide Note The number of screws to be removed will d epend on the model of spa. Remove the Sub Woofer Compartment Panel The installatio n location of the su b woofer compartment will vary from one spa model to another.
Export Sonic Immers ion System Dealer Installation Guide Sub-Woofer Installation Locator Top Side Control Table 4 Model List Model and Number Location of Installation Aurora II and Chairman Top Side C.
Export Sonic Immers ion System Dealer Installation Guide Caliente HP, Triad II, Aurora HP, and Triad Top Side Control 1. Use the screwdriver to remove the spa panel screws, Figure 3. Figure 3. Equipment Compartment Panel Screws Note The number of screws to be removed will depend on the model of s pa.
Export Sonic Immers ion System Dealer Installation Guide Installing the Sub Woofer Compartment The installatio n of the sub woofer compartment consists of removing the panel, removing the pa per cover, exposing the plug , removing the plug, and installi ng the sub woofer compartment.
Export Sonic Immers ion System Dealer Installation Guide Note The photograph Figure 5 may not look like your spa, refer to Table 4. 1. Sub-Woofer Plug Figure 6. Sub-Woofer Plug 3. Once the plug is exposed, Figure 6, use a screwdriver to punch holes in the foam large enough to insert your ha nds and pull the plug out of the spa, Fig ure 7.
Export Sonic Immers ion System Dealer Installation Guide Figure 7. Removing Plug 4. Use a medium size pair of ne edle nose pliers to remove the large staples in the bottom ra il where the plug was removed. 5. Remove all remnants of the plastic bag inside th e compartment where the plug was removed.
Export Sonic Immers ion System Dealer Installation Guide 1. Electrical Condui t Before Trimming Figure 8. Electrical Conduit 6. Using a non-ratcheti ng PVC pipe cutter, trim the elec trical conduit flush with the foam wall, Figure 9. 1. Electrical Condui t After Trimming Figure 9.
Export Sonic Immers ion System Dealer Installation Guide 7. Locate the sub woofer sub assembly (P/N 01564-09). Locate the spot on the compartme nt that matches the locatio n of the conduit in the s pa. Using a1½ inch (3.8 cm) hole saw, drill a hole for the conduit, Figure 10.
Export Sonic Immers ion System Dealer Installation Guide 1. Bottom Edge of Frame Figure 11. Edge of Frame 9. A properly positioned s ub woofer compartment is show n in Figure 12.
Export Sonic Immers ion System Dealer Installation Guide 10. Once you are satisfied that the compartment fits properly , secure the compartment to the frame, Figure 13, with 5 1“ (2.54 cm) coarse-threaded drywall screws ( P/N 01051-06 provided in hardware package).
Export Sonic Immers ion System Dealer Installation Guide 1. Fish Tape Figure 14. Fish Tape in Equipment Compartment 2. Now locate the amplifier cables (two white and two red RCA connectors on both ends, P/N 01570-24). Locate the three- branched harness assembly (P/N 01564-20).
Export Sonic Immers ion System Dealer Installation Guide 4. Apply a small amount of fis h tape lubricant to a cloth and then run th e cables through the rag to give them a li ght coating of lubricant, Figure 16. Figure 16. Applying Lubricant to Cables 5.
Export Sonic Immers ion System Dealer Installation Guide woofer compartment, t he wires and cables can be connected to the amplifier in the sub-w oofer compartment. You may want to trim off some of the harness becaus e it could be longer than necessary.
Export Sonic Immers ion System Dealer Installation Guide 1. Speaker Output T erminals. 2. Power Input Terminals 3. Red Wire 4. Blue Wire 5. Black Wire Figure 19. Connecting Wires for Power Input 8. Locate the wire coming from the sub-woofe r. This wire is covered with clear insulator.
Export Sonic Immers ion System Dealer Installation Guide to red and white terminals on left, co nnect Channel 2 (sub - woofer speaker) to red and white terminals on right, Figures 21 and 22. 1. Line Level Input 2 . Mode Control 3. Bass Boost Contro l 4.
Export Sonic Immers ion System Dealer Installation Guide Figure 23. Setting Controls 12. Set BASS BOOST CH1 and CH 2 to th e MIN position. 13. Set HIGH PASS CH 1 and CH 2 to the 200 HZ positio ns.
Export Sonic Immers ion System Dealer Installation Guide 1. Green 2. Yellow 3. Red 4. Blue 5. Black 6. Row 3 Amplifier 7. Row 2 St ereo 8. Row 1 120 V Suppl y 9.
Export Sonic Immers ion System Dealer Installation Guide 2. Connect the wires coming from Row 2 (Ster eo +12 V Supply) as follows: (Figure 26) yellow and red wires to terminal marked “DC+” and the black wire to terminal marked “DC- “. 1. Black Wire 2.
Export Sonic Immers ion System Dealer Installation Guide Installing Power Supply in Equipment Compartment 1. Turn the p ower supply so that you can see the Voltage Selector Switch, see Fig ure 28, and place the switch in the correct position (115V for UL and CSA spas or 240V for CE spas) for your location.
Export Sonic Immers ion System Dealer Installation Guide 1. Location of Upper and Lower Screw Holes Figure 29. Location of Attachment Holes on Power Supply 3. Locate the connector on the harness assembly that matches the one that you just installe d on the power supply and connect them together, Figure 30.
Export Sonic Immers ion System Dealer Installation Guide Wiring the Power Supply 1. Locate the end of the harnes s that has a green, black, and white wire (with connectors). Remove lower control box cover. Insert these wires throug h the hole in the botto m of the lower control box, F igure 31.
Export Sonic Immers ion System Dealer Installation Guide Figure 32. Removing Nut from Ground Terminal 3. Now place the green ground wire that you just inserted into the lower control box over the screw, replace 5/16” (7.9 mm) nut, and secure with 5/16”(7.
Export Sonic Immers ion System Dealer Installation Guide Determining Location of CD Weather Cover The installatio n location of the CD Player Weather Cover (P/N 01564-04) dep ends on the model of the spa. The follo wing steps will guide you through the proces s of determining the instal lation location.
Export Sonic Immers ion System Dealer Installation Guide Note It is important that the ruler or square (see picture on previous page ) be kept level and at the top of the recess area while making these measurements.
Export Sonic Immers ion System Dealer Installation Guide 1. Bottom of Panel 2. Pane l Lay Face Up 3. Top of Panel Figure 34. Measuring Vertical Distance 2. Using measurement obtained for Horizontal Position (HP) , measure from side of panel, see Figure 35, and mark spot with a fine point marker.
Export Sonic Immers ion System Dealer Installation Guide 3. The point where these t wo lines intersect is the upper right corner of the template (P/N Doc 74 Rev A). 4. Align the upper right cor ner of the template wit h the mark on the panel. Use a center punc h to mark the spot, Fig ure 36.
Export Sonic Immers ion System Dealer Installation Guide 7. Using a 3/8” (9.5 mm) bit, drill holes in t wo corners of the rectangle, Figure 38. Make cert ain that the holes are wi thin the lines. Using a cen ter punch to m ark the drilling centers will prevent the drill bi t from wandering.
Export Sonic Immers ion System Dealer Installation Guide Installation of CD Pl ayer Door and Bezel If the bezel is not removed fr om the door assembly (P/N 01564-04), remove it by pull ing from the b ottom of the b ezel and then p roceed as follows, see Figure 40: 1.
Export Sonic Immers ion System Dealer Installation Guide Figure 41. Door Assembly Installed 4. Reattach th e bezel. 5. Locate the mounting sleeve su pplied with the CD player and refer to the CD Player Owner’ s manual for directions on how to install this sleeve.
Export Sonic Immers ion System Dealer Installation Guide Figure 42. Door Assembly Ready for CD Player Connection 3. Reattach panel to spa. 4. Connect antenna, main harness and amplifier to CD player as described in CD player owner’s manual. Connect po wer supply cable (long branch of main harness) to power supply connector on CD player.
Export Sonic Immers ion System Dealer Installation Guide Installing the Satellite Speakers Locate the panel where you will in s tall the speakers, Figure 43.
Export Sonic Immers ion System Dealer Installation Guide 1. Caps in Place Figure 44. Protective Caps in Place 41.
Export Sonic Immers ion System Dealer Installation Guide Installing the Satellite Speaker Wires 1. Remove the panel w here you just finished in stalling the speakers. 2. Locate two speaker wire sets (P/N 01 564-21). The wires have clear insulator with a silver and copper wire and female connectors on one end.
Export Sonic Immers ion System Dealer Installation Guide 1. When pushed all the way up und er the lip, the wire or cable will rest safely on the lip of the spa wall 2. Cable or Wire . 3. Spa Shell’s Lip 4. Wooden Ruler or Paint S tir Stick 5. Install Wire or Cable Under the Spa Shell’s Lip Figure 46.
Export Sonic Immers ion System Dealer Installation Guide 5. Continue installi ng the wire until you reach the panel where the sub-woofer compart ment has been installed. Now use the Cable Tyes and Cable Mounts to attach the wire to the wood until you reach the sub woofe r compartment, Figure 4 7.
Export Sonic Immers ion System Dealer Installation Guide 1. Copper Wire 2. Copper Wir e 3. Silver Wire 4. Silver W ire Figure 48. Connecting Satellite Speaker Wires to Amplifier 8. Now connect the wires coming from the sub-woofer compartment to the sate llite speakers.
Export Sonic Immers ion System Dealer Installation Guide 9. Place the panel back on the spa and secure wit h screws. The finished installatio n should appear as in the pictures show n in Figure 50.
Export Sonic Immers ion System Dealer Installation Guide Securing the Amplifier Now that the speakers have been installed and the amplifier has been adjusted it can be secured to the fra me, Figure 51, with dry wall screws supplied in the kit (P/ N 01051-06).
.
.
Part No. 01510-1030E Rev A 2002 Dimension One Spas.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Dimension One Spas 01510-1030E Rev A c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Dimension One Spas 01510-1030E Rev A - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Dimension One Spas 01510-1030E Rev A, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Dimension One Spas 01510-1030E Rev A va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Dimension One Spas 01510-1030E Rev A, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Dimension One Spas 01510-1030E Rev A.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Dimension One Spas 01510-1030E Rev A. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Dimension One Spas 01510-1030E Rev A ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
