Manuel d'utilisation / d'entretien du produit XPS GEN 3 du fabricant Dell
Aller à la page of 144
www .dell.com | support.dell.com Dell™ Dimension™ XPS Gen 3 headphone connector microphone connector USB 2.0 connectors (2) IEEE 1394 connector PCI card (4), PCI Express x1 card (1), PCI Express x16 card (1) slots serial port parallel port diagnostic lights keyboard connector USB 2.
www .dell.com | support.dell.com Notes, Notices, and Cautions NOTE: A NOTE indicates important i nformation that helps you make better use of your computer . NOTICE: A NOTICE indicates either potential da mage to hardware or loss of da ta and tells you how to avoid the problem.
Contents 3 Contents Finding Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1 Setting Up and Using Y our Computer Opening the Drive Door . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Changing the Backlight Color . . . . .
4 Contents 3 Solving Problems T roubleshooting T ips . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Battery Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Drive Problems . . . . . . . . . . . . . . . . . . . . . . . .
Contents 5 4 Advanced T roubleshooting Diagnostic Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Dell Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 When to Use the Dell Diagnostics . . . . . . . . . . .
6 Contents Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 PCI Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 PCI Express Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Drives . . .
Contents 7 6 Appendix Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 Sy stem Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Entering Sy stem Setup .
8 Contents.
Finding Information 9 Finding Information What Are Y ou Looking For? Find it Here • How to access tutorials an d other how to information • How to get a copy of my invoice • How to extend my warranty • How to access Dell Support on my Microsoft ® W indows ® desktop (U.
10 Finding Information www .dell.com | support.dell.com • W arranty information • Safety instructions • Regulatory information • Ergonomics information • End User License Agreement Dell™ P.
Finding Information 11 • Service T ag and Express Service Code • Microsoft W indows License Label Service T ag and Microsoft Windows License These labels are located on your computer . •Use the Service T ag to identify your computer when you use support.
12 Finding Information www .dell.com | support.dell.com • How to reinstall my operating system Operating Sy stem CD The operating system is already installed on your computer . T o reinstall your operating system, use the Operating System CD. See "Reinstalling Microsoft ® W indows ® XP" on page 57.
Setting Up and Using Y our Computer 13 Setting Up and Using Y our Computer Opening the Drive Door Changing the Backlight Color Y ou can use this e xclusive Dell™ Dimension™ XPS Ge n 3 feature eith.
14 Setting Up and Using Y our Computer www .dell.com | support.dell.com There ar e several color choices: • R uby •E m e r a l d • Sapphire (default) •A m b e r • Amethyst •T o p a z • Diamond CAUTION: Before you begin any of the proce dures in this section, follow the safety instructions located in the Product Information Guide .
Setting Up and Using Y our Computer 15 5 Click F ront LED Color , and press <Enter>. 6 P ress the left- and right- arrow keys to scroll through the color options. The backlight color changes as you scroll through the options. 7 Select the color you want, and press <Enter>.
16 Setting Up and Using Y our Computer www .dell.com | support.dell.com Connecting One Monitor With a VGA connector and One Monitor With a DVI Connector 1 F o llow the procedur es in "Before Y ou Begin" on page 61. 2 Connect the VGA connector on the monitor to the VGA (blue) connector on the back of the computer .
Setting Up and Using Y our Computer 17 Changing the Display Settings 1 After you connect the monitor(s) or TV , turn on the computer . The Microsoft ® W indows ® desktop displays on the primary monitor . 2 Enable clone mode or extended desktop mode in the display settings.
18 Setting Up and Using Y our Computer www .dell.com | support.dell.com RAID Level 0 R AID level 0 uses a storage technique known as "d ata striping" to provide a high data access rate. Data striping is a method of writing consecutive segments, or stripes, of data sequentially across the physical drives to create a lar ge virtual drive.
Setting Up and Using Y our Computer 19 If a drive failure occurs, subsequent r ead and write operations are dir ected to the surviving drive. A replacement drive can then be r ebuilt using the data from the surviving drive.
20 Setting Up and Using Y our Computer www .dell.com | support.dell.com 5 Use the left- and right-arrow keys to highlight Save/Exit , and press <Enter> to e xit system setup and resume the boot process.
Setting Up and Using Y our Computer 21 4 Enter a R AID volume name or acce pt the default, and press <Enter>. 5 Use the up- and down-arrow keys to select R AID1(Mirror) , and press <Enter>.
22 Setting Up and Using Y our Computer www .dell.com | support.dell.com Creating a RAID 0 V olume NOTE: When you perform this operation, all data on the RAID drives will be lost.
Setting Up and Using Y our Computer 23 Deleting a RAID V olume NOTE: While this procedure deletes the RAID 1 volume, it also splits the RAID 1 volume into two non- RAID hard drives with a partition, and leaves any ex isting data files intact. De leting a RAID 0 volume, however , destroy s all data on the volume.
24 Setting Up and Using Y our Computer www .dell.com | support.dell.com 11 Click Fi n i s h to start migrating, or click Back to make changes. Y o u can use your computer normally during the migration process. Migrating to a RAID 1 V olume 1 Set your computer to R AID-enabled mode (see page 19).
Setting Up and Using Y our Computer 25 T o Remove Spare Marking F rom a Spare Hard Drive: 1 Right-click the spare har d drive icon. 2 Click Reset Hard Drive to Non-R AID Rebuilding a Degrad ed RAID 1 .
26 Setting Up and Using Y our Computer www .dell.com | support.dell.com 3 Under What do you want to do? , click T ransfer files and settings . 4 On the F iles and Settings T ransfer Wizard welcome screen, click Next . 5 On the Which computer is this? screen, click Old Computer and click Next .
Setting Up and Using Y our Computer 27 NOTE: Most commercial DVDs have copyright protect ion and cannot be copied using Sonic R ecordNow . 1 Click the Start button, point to All P rograms → Sonic → Rec ord No w! → RecordNow! 2 Click either the audio tab or the data tab, depending on the kind of CD or D VD you are planning to copy .
28 Setting Up and Using Y our Computer www .dell.com | support.dell.com • Do not burn a blank CD-R or CD-R W to its maximum capacity ; for example, do not copy a 650-MB file to a 650-MB blank CD. The CD-R W dr ive needs 1 or 2 MB of the blank CD to finalize the recor ding.
Optimizing Performance 29 Optimizing Performance Hyper -Threading Hyper - Thr eading is an Intel ® technology that can enhance overall computer performance by allowing one physical processor to function as t wo logical processors, capable of performing certain tasks simultaneously .
30 Optimizing Performance www .dell.com | support.dell.com PCI Express Cards PCI Express is the ne xt generation technology fo r graphics cards and PCI cards.
Solving Problems 31 Solving Problems T roubleshooting T ips F ollow these tips when you troubleshoot your computer: • If you added or removed a part befor e the prob lem started, review the installation procedures and ensure that the part is corr ectly installed.
32 Solving Problems www .dell.com | support.dell.com CD and DVD drive problems NOTE: High-speed CD or DVD drive vibration is normal and may cause noise, which does not indicate a defect in the drive or the CD or DVD. NOTE: Because of different regions worldwide and different disc formats, not all DV D titles work in all DVD drives.
Solving Problems 33 Hard drive problems E-Mail, Modem, and Internet Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide . NOTE: Connect the modem to an analog tel ephone jack only .
34 Solving Problems www .dell.com | support.dell.com Error Messages CAUTION: Before you begin any of the proc edures in this section, fo llow the safety instructions located in the Product Information Guide . If the message is not listed, see the documentatio n for the operating system or the program that was running when the message appeared.
Solving Problems 35 IEEE 1394 Device Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide . Keyboard Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide .
36 Solving Problems www .dell.com | support.dell.com Lockups and Software Problems CAUTION: Before you begin any of the proc edures in this section, fo llow the safety instructions located in the Product Information Guide .
Solving Problems 37 A program crashes repeatedly NOTE: Software usually includes installation instructions in its documentation or on a floppy disk or CD.
38 Solving Problems www .dell.com | support.dell.com Memory Problems CAUTION: Before you begin any of the proc edures in this section, fo llow the safety instructions located in the Product Information Guide .
Solving Problems 39 Network Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide . R ESTART THE COMPUTER — 1 Simultaneously press <Ctr l><Esc> to display the Start menu.
40 Solving Problems www .dell.com | support.dell.com Power Problems CAUTION: Before you begin any of the proc edures in this section, fo llow the safety instructions located in the Product Information Guide . I F THE POWER LIGHT IS GREEN AND THE COMPUTER IS NOT RESPONDING — See "Diagnostic Lights" on page 47.
Solving Problems 41 Printer Problems CAUTION: Before you begin any of the procedures in th is section, follow the s afety instructions located in the Product Information Guide . NOTE: If you need technical assistan ce for your printer , contact the printer’ s manufacturer .
42 Solving Problems www .dell.com | support.dell.com Sound and Speaker Problems CAUTION: Before you begin any of the proc edures in this section, fo llow the safety instructions located in the Product Information Guide . No sound from speakers NOTE: The volume control in some MP3 players overrides the Windows vo lume setting.
Solving Problems 43 No sound from headphones D ISCONNECT HEADPHONES FROM THE HEADPHONE CONNECTOR — Sound from the speakers is automatically disabled when headphones are conne cted to the computer’s front-panel headphone connector .
44 Solving Problems www .dell.com | support.dell.com V ideo and Monitor Problems CAUTION: Before you begin any of the proc edures in this section, fo llow the safety instructions located in the Product Information Guide . If the screen is blank NOTE: See the monitor docume ntation for troubles hooting procedures.
Solving Problems 45 A DJUST THE W INDOWS DISPLAY SETTINGS — 1 Click the Start button, click Control P anel , and then click Appearance and Themes . 2 Click Display and click the Settings tab. 3 T ry different settings for Screen resolution and Color quality .
46 Solving Problems www .dell.com | support.dell.com.
Advanced T roubleshooting 47 Advanced T roubleshooting Diagnostic Lights CAUTION: Before you begin any of the proce dures in this section, follow the safety instructions located in the Product Information Guide .
48 Advanced T roubleshooting www .dell.com | support.dell.com Memory modules are detected, but a memory failure has occurr ed. • If you have two or more memory modules installed, remove the modules, reinstall one module (see page 71), and then restart the computer .
Advanced T roubleshooting 49 No memory modules are detected. • If you have two or more memory modules installed, remove the modules, reinstall one module (see page 71), and then restart the computer . If the computer starts normally , reinstall an additional module.
50 Advanced T roubleshooting www .dell.com | support.dell.com Dell Diagnostics CAUTION: Before you begin any of the proc edures in this section, fo llow the safety instructions located in the Product Information Guide .
Advanced T roubleshooting 51 Starting the Dell Diagnostics From Y our Hard Drive 1 T urn on (or restart) your computer . 2 When the DELL™ logo appear s, press <F12> immediately . NOTE: If you see a message stating that no diagnostics utility partitio n has been found , run the Dell Diagnostics from your ResourceCD (see page 51).
52 Advanced T roubleshooting www .dell.com | support.dell.com Dell Diagnostics Main Menu 1 After the Dell Diagnostics loads and the Main Menu screen appears, click the button for the option you want. 2 If a problem is encountered during a test, a message appears with an error code and a description of the problem.
Advanced T roubleshooting 53 4 When the tests are completed, if you ar e runni ng the Dell Diagnostics from the ResourceCD , remove the CD. 5 Close the test screen to r eturn to the Main Menu screen. T o exit the Dell Diagnostics and restart the computer , close the Main Menu screen.
54 Advanced T roubleshooting www .dell.com | support.dell.com Windows XP 1 Click the Start button and click Control P anel . 2 Under Pick a Category , click P erformance and Maintenance . 3 Click System . 4 In the System P roperties window , click the Hardware tab.
Advanced T roubleshooting 55 3 When the InstallShield Wizard Complete window appears, remove the ResourceCD and click Fi n i s h to restart the computer . 4 When you see the W indows desktop, reinsert the ResourceCD. 5 At the W elcome Dell System Owner screen, click Next .
56 Advanced T roubleshooting www .dell.com | support.dell.com Creating a Restore Point 1 Click the Start button and click Help and Support . 2 Click System Restore .
Advanced T roubleshooting 57 3 Click Next . The System Restore screen appears and the computer r estarts. 4 After the computer restarts, click OK . Enabling Sy stem Restore If you reinstall W indows XP with less than 200 MB of free har d-disk space available, System Restore is automatically disabled.
58 Advanced T roubleshooting www .dell.com | support.dell.com T o reinstall W i ndows XP , you need the following items: • Dell™ Operating System CD • Dell ResourceCD NOTE: The ResourceCD contains drivers that were in stalled during assembly of the computer .
Advanced T roubleshooting 59 5 P ress <Enter> to select the highlighted partition (recommended), and follow the instructions on the screen. The Windows XP Setup screen appears, and the operating system begins to copy files and install the devices.
60 Advanced T roubleshooting www .dell.com | support.dell.com 19 Reinstall the appropriate drivers with the ResourceCD (see page 54). 20 Reinstall your virus protection software.
Removing and Installing Parts 61 Removing and Installing Parts Before Y ou Begin This chapter provides procedures for r emoving and installing the components in your computer .
62 Removing and Installing Parts www .dell.com | support.dell.com Before W orking Inside Y our Computer Use the following safety guidelines to help protec t your computer from potential damage and to help ensure your own personal safety .
Removing and Installing Parts 63 Front and Back V iew of the Computer Front View 2 1 3 4 1 hard-drive activity light The hard-drive light is on when the computer r eads data from or writes data to the hard drive. The light might also be on when a device such as yo ur CD player is operating.
64 Removing and Installing Parts www .dell.com | support.dell.com Front View (Doors Open) 2 1 3 4 1 headphone connector Use the headphone connector to attach headphones and most kinds of speakers.
Removing and Installing Parts 65 Back View 7 11 9 2 1 3 13 12 15 16 5 17 19 8 6 14 4 10 18 1 processor fans (2) F or optimal cooling, two proc essor fans are provided. Do not block the vents. 2 cover latch release T o open the computer , lay the computer on it s side with the cover latch release at the top and then push the latch to the le ft.
66 Removing and Installing Parts www .dell.com | support.dell.com 4 TV -OUT connector Connects your computer to a TV . F or more information, see "Connecting T wo Monitors" on page 15. 5 DVI video connector If your monitor has a DV I connector , plug it into the D VI connector on the computer .
Removing and Installing Parts 67 Opening the Computer Cover CAUTION: Before you begin any of the procedures in this section , follow the safety instructions located in the Product Information Guide .
68 Removing and Installing Parts www .dell.com | support.dell.com Inside V iew of Y our Computer hard drive shroud floppy drive CD/DVD drive sy stem board processor airflow shroud power supply process.
Removing and Installing Parts 69 Sy stem Board Components hard-drive connector (PRI_IDE) battery socket (BA TTERY) SCSI LED header (SCSI LED) front-panel connector (FRONT P ANEL) backlight connector (.
70 Removing and Installing Parts www .dell.com | support.dell.com Memory Y ou can increase your computer memory by inst alling memory modules on the system board. Y our computer supports DDR2 memory . F or addit ional information on the type of memory supported by your computer , see "Memory" on page 109.
Removing and Installing Parts 71 NOTE: Memory purchased from Dell is co vered under your computer warranty . NOTICE: If you remove your original memory modules fr om the computer during a memory upgrade, keep them separate from any new modules that you may have, even if you purchased the new modules from Dell.
72 Removing and Installing Parts www .dell.com | support.dell.com 3 P ress out the securing clip at each end of the memory module connector . 4 Align the notch on the bottom of the mo dule with the crossbar in the connector .
Removing and Installing Parts 73 6 Close the computer cover . NOTICE: T o connect a network cable , first plug the cable in to the network wall jack and then plug it into the computer . 7 Connect your computer and devices to el ectrical outlets, and turn them on.
74 Removing and Installing Parts www .dell.com | support.dell.com Y our Dell™ computer provides the follow ing slots for PCI and PCI Express car ds: • F our PCI card slots • One PCI Express x16 car d slot • One PCI Express x1 car d slot PCI Cards If you are installing or r eplacing a card, follow the procedur es in the next section.
Removing and Installing Parts 75 3 If you are installing a new car d, remove the f iller bracket to cr eate a card-slot opening. Then continue with step 5. 4 If you are r eplacing a card that is alread y installed in the computer , remove the car d. If necessary , disconnect any cables connected to the card.
76 Removing and Installing Parts www .dell.com | support.dell.com NOTICE: Do not route card cables over or behind the cards. Cables ro uted over the cards can prevent the computer cover from closing proper ly or cause damage to the equipment. 9 Connect any cables that should be attached to the card.
Removing and Installing Parts 77 5 If you are r emoving the card permanently , in stall a filler brack et in the empty card-slot opening. If you need a filler bracket, contact Dell (see page 121). NOTE: Installing filler brackets over empty card-slot op enings is necessary to maintain FCC certification of the computer .
78 Removing and Installing Parts www .dell.com | support.dell.com Installing a PCI Express Card 1 F o llow the procedur es in "Before Y ou Begin" on page 61.
Removing and Installing Parts 79 3 If you are installing a new car d, remove the f iller bracket to cr eate a card-slot opening. Then continue with step 5. 4 If you are r eplacing a card that is alread y installed in the computer , remove the car d. If necessary , disconnect any cables connected to the car d.
80 Removing and Installing Parts www .dell.com | support.dell.com 8 If you replaced a car d that was already installe d in the computer and you r emoved the top of the retention mechanism, you can r einstall the top. 9 Before you lower the r etention arm, ensure that: • The tops of all cards and filler brack ets are flush with the alignment bar .
Removing and Installing Parts 81 Removing a PCI Express Card 1 F ollow the procedures in "Before Y ou Begin" on page 61. 2 P ress the lever on the card r etention arm and raise the retention arm. 3 If necessary , disconnect any cables connected to the card.
82 Removing and Installing Parts www .dell.com | support.dell.com Drives Y our computer supports a combination of these devices: • Up to three har d drives • One floppy drive • Up to two CD or D.
Removing and Installing Parts 83 Connecting Drive Cables When you install a drive, you connect two cables— a DC power cable and a data cable—to the back of the drive and to the system boar d. Some drives may also have an audio connector; one end of the audio cable attaches to the dr ive connector and the other end attaches to the system board.
84 Removing and Installing Parts www .dell.com | support.dell.com Power Cable Connector Hard Drive CAUTION: Before you begin any of the proce dures in this section, follow the safety instructions located in the Product Information Guide . NOTICE: T o avoid damage to the drive, do not set it on a hard surface.
Removing and Installing Parts 85 3 Disconnect the power and hard-drive cables from the drive and from the system boar d. 4 P ress in on the tabs on each side of the drive and slide the drive up and out. Installing a Hard Drive 1 Unpack the replacement har d drive, and prepare it for installation.
86 Removing and Installing Parts www .dell.com | support.dell.com 4 Install the hard drive into the computer by ge ntly sliding the drive into place until the tabs securely click into position.
Removing and Installing Parts 87 NOTICE: When replacing the hard-drive shroud, ensure that all the cables are properly routed. 8 Insert the bottom tabs of the shroud in to the holes on the drive cage and rotate the shroud up. 9 P ress in on the top tabs and lock them in to place.
88 Removing and Installing Parts www .dell.com | support.dell.com 16 Exit system setup, and restart the computer . 17 P artition and logically format your driv e before you proceed to the next step. See the documentation for your operating system for instructions.
Removing and Installing Parts 89 7 Connect a power cable to the drive. 8 Connect the hard-drive cable to the driv e and to the system boar d (see page 69). 9 Close the computer cover (see page 108). NOTICE: T o connect a network cable, firs t plug the cable into the network device and then plug it into the computer .
90 Removing and Installing Parts www .dell.com | support.dell.com 3 P ress inward on the two tabs on the sides of th e drive, slide the drive upwar d, and remove it from the floppy-drive bay .
Removing and Installing Parts 91 2 Gently slide the drive into place until the tabs securely click into position. drive screws (4) bracket rails (2) data cable power cable tabs (2) floppy drive.
92 Removing and Installing Parts www .dell.com | support.dell.com 3 Attach the power and data cables to the floppy drive. 4 Connect the other end of the data cable to the connector labled FLOPPY on the system board (see page 69). 5 Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents.
Removing and Installing Parts 93 3 P ress inward on the two tabs on the sides of th e drive, and then slide the drive upwar d and remove it from the drive bay . Installing a CD/DVD Drive 1 If you are installing a new drive, unpack the drive and pr epare it for installation.
94 Removing and Installing Parts www .dell.com | support.dell.com 3 If you are installing a r eplacement drive and th e new drive does not have the bracket rails attached, remove the rails from the old drive by r emoving the tw o screws that secur e each rail to the drive.
Removing and Installing Parts 95 6 Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents. 7 Close the computer cover (see page 108). NOTICE: T o connect a network cable , first plug the cable in to the network wall jack and then plug it into the computer .
96 Removing and Installing Parts www .dell.com | support.dell.com Processor Airflow Shroud Removing the Processor Airflow Shroud CAUTION: Before you perform this pr ocedure, follow the safety instructions located in the Product Information Guide .
Removing and Installing Parts 97 Installing the Processor Airflow Shroud 1 Attach both fan power cables to the connectors on the system board. 2 Align the anchor tabs with the securing slots. 3 Gently press the shroud until the anchor tabs snap secur ely into place.
98 Removing and Installing Parts www .dell.com | support.dell.com CAUTION: The heat sink can get very hot during normal operation. Be su re that the heat sink has had sufficient time to cool b efore you touch it. 5 Remove the heat sink: a Remove the retention module clips.
Removing and Installing Parts 99 b On the retention base locate the tab opposite the power supply . P ress on the retention base tab until the heat sink pops up slightly . c P ress out on the second retention tab while lifting the heat sink up and out of the retention base.
100 Removing and Installing Parts www .dell.com | support.dell.com 8 Remove the processor from the socket. Leave the release lever extended in the r elease position so that the socket is ready for the new processor . Installing the Processor NOTICE: Ground yourself by touching an unpainted metal surface on th e back of the computer .
Removing and Installing Parts 101 NOTICE: Socket pins are delicate. T o avoid damage, en sure that the pr ocessor is aligned properly with the socket, and do not use excessive force when you install the pr ocess. Be careful not to touch or bend the pins on the sy stem board.
102 Removing and Installing Parts www .dell.com | support.dell.com 7 Install the heat sink: a Slide one end of the heat sink under the retention tab. b P ull out the other retention tab and lower the he at sink until it fits secur ely in the base. NOTICE: Ensure the heat sink is co rrectly seated and secure.
Removing and Installing Parts 103 4 Close the computer cover halfway and pull the front panel away from the computer . Replacing the Front Panel T o replace the front panel, perform the r emoval procedure in reverse.
104 Removing and Installing Parts www .dell.com | support.dell.com Drive Door CAUTION: Before you begin any of the proc edures in this section, fo llow the safety instructions located in the Product Information Guide . Removing the Drive Door 1 Open the drive door .
Removing and Installing Parts 105 2 Unsnap the top bracket hinge and pull the to p of the drive door outwar d, away from the computer . 3 Lift the bottom bracket hinge away from the computer .
106 Removing and Installing Parts www .dell.com | support.dell.com 2 Attach the door bracket/door hinge assembly to th e door , starting with the lower part of each door hinge. 3 Attach the drive door to the computer , starting with the bottom bracket hinge.
Removing and Installing Parts 107 Battery Replacing the Battery CAUTION: Before you begin any of the procedures in this section , follow the safety instructions located in the Product Information Guide .
108 Removing and Installing Parts www .dell.com | support.dell.com NOTICE: T o connect a network cable, first plug the cable into the network device and then plug it into the computer . 7 Connect your computer and devices to elec trical outlets, and turn them on.
Appendix 109 Appendix Specifications Processor P r ocessor type Intel ® Pe n t i u m ® 4 with HT T echnology NOTE: Not all Pentium 4 processors support Hyper -Threading technology .
110 Appendix www .dell.com | support.dell.com Video T ype PCI Express Expansion Bus Bus type PCI 2.3 PCI Express x1 and x16 Bus speed PCI: 33 MHz PCI Express: x1 slot bidirectional speed - 500 MB/s x1.
Appendix 111 Internally accessible: two bays for 1-inch high hard drives Connectors External connectors: Serial 9-pin connector; 16550C-compatible P arallel 25-hole connector (bidirectional) IEEE 1394.
112 Appendix www .dell.com | support.dell.com Link integrity light (on integrated network adapter) green light — A good connection exists between a 10-Mbps network and the computer . orange light — A good connection exists between a 100-Mbps network and the computer .
Appendix 113 Sy stem Setup Overview Use system setup as follows: • T o change the system configuration information after you add, change, or remove any hardwar e in your computer • T o set or chan.
114 Appendix www .dell.com | support.dell.com Entering Sy stem Setup 1 T urn on (or restart) your computer . 2 When the blue DELL™ logo appears, press <F2> immediately . If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft ® W indows ® desktop.
Appendix 115 Sy stem Setup Options NOTE: Depending on your comp uter and installed devices, the item s listed in this section may not appear , or may not appea r exactly as listed. System System Info Lists system information such as the computer name, the BIOS version number and date, system tags, and other system-specific information.
116 Appendix www .dell.com | support.dell.com LPT Port Mode Identifies and defines the parallel port settings. Y ou can set the parallel port to Off, AT , PS/2 , EPP , or ECP . LPT Port Address Identifies the address for the parallel port. LPT Port DMA Identifies and defines the parallel port DMA settings.
Appendix 117 Auto Power On Sets the computer to automa tically turn on. Choices are every day or every Monday through F riday . The default setting is Off . This feature does not work if you turn off your computer using a power strip or surge protector .
118 Appendix www .dell.com | support.dell.com Boot Sequence This feature allows you to change the boot sequence for devices. Option Settings • Diskette Drive — The computer attempts to boot from the floppy drive.
Appendix 119 4 At the bottom of the menu, enter the number of the device that is to be used for the current boot only . F or example, if you are booting to a USB memory k ey , highlight USB Flash Device and press <Enter>. NOTE: T o boot to a USB device, the device must be boot able.
120 Appendix www .dell.com | support.dell.com 2 Locate the 3-pin password jumper (PSWD) on the system board (see page 69), and attach the jumper plug to pins 2 and 3 to clear the password. NOTE: When you receive your computer , the jum per plug is attache d to pins 1 and 2.
Appendix 121 Dell T echnical Support Policy (U.S. Only) T echnician-assisted technical support requir es th e cooperation and participation of the customer in the troubleshooting process and provides .
122 Appendix www .dell.com | support.dell.com NOTE: T oll-free numbers are for use within the country for which they are listed. When you need to contact Dell, use the electr onic addresses, telephone numbers, and codes provided in the following table.
Appendix 123 Bahamas General Support toll-free: 1-866-278-6818 Barbados General Support 1-800-534-3066 Belgium (Brussels) International Access Code: 00 Country Code: 32 City Code: 2 W ebsite: support.euro .dell.com E-mail: tech_be@dell.com E-mail for F rench Speaking Customers: support.
124 Appendix www .dell.com | support.dell.com Canada (North Y ork, Ontario) International Access Code: 011 Online Order Status: www .dell.ca/ostatus AutoT ech (automated technical support) toll-free: 1-800-247-9362 T echF ax toll-free: 1-800-950-1329 Customer Care (Home Sales/Small Business) toll-free: 1-800-847-4096 Customer Care (med.
Appendix 125 China (Xiamen) Country Code: 86 City Code: 592 T ech Support website: support.dell.com.cn T ech Support E-mail: cn_support@dell.com T ech Support F ax 818 1350 T echnical Support (Dimensi.
126 Appendix www .dell.com | support.dell.com Czech Republic (P rague) International Access Code: 00 Country Code: 420 City Code: 2 W e bsite: support.
Appendix 127 F inland (Helsinki) International Access Code: 990 Country Code: 358 City Code: 9 W ebsite: support.euro .dell.com E-mail: fin_support@dell.
128 Appendix www .dell.com | support.dell.com Germany (Langen) International Access Code: 00 Country Code: 49 City Code: 6103 W e bsite: support.euro .
Appendix 129 India T echnical Support 1600 33 8045 Sales 1600 33 8044 Ireland (Cherrywood) International Access Code: 16 Country Code: 353 City Code: 1 W ebsite: support.euro .dell.com E-mail: dell_direct_support@dell.com T echnical Support 1850 543 543 U.
130 Appendix www .dell.com | support.dell.com Japan (Kawasaki) International Access Code: 001 Country Code: 81 City Code: 44 W e bsite: support.jp.dell.
Appendix 131 Latin America Customer T echnical Support (Austin, T exas, U.S.A.) 512 728-4093 Customer Service (Austin, T exas, U.S.A.) 512 728-3619 F ax (T echnical Support and Customer Service) (Austin, T exas, U.S.A.) 512 728-3883 Sales (Austin, T exas, U.
132 Appendix www .dell.com | support.dell.com Mexico International Access Code: 00 Country Code: 52 Customer T echnical Support 001-877-384-8979 or 001-877-269-3383 Sales 50-81-8800 or 01-800-888-3355.
Appendix 133 New Zealand International Access Code: 00 Country Code: 64 E-mail (New Zealand): nz_tech_support@dell.com E-mail (Australia): au_tech_support@dell.
134 Appendix www .dell.com | support.dell.com P ortugal International Access Code: 00 Country Code: 351 W e bsite: support.euro .dell.com E-mail: support.
Appendix 135 Spain (Madrid) International Access Code: 00 Country Code: 34 City Code: 91 W ebsite: support.euro .dell.com E-mail: support.euro .dell.com/es/es/emaildell/ Home and Small Business T echn.
136 Appendix www .dell.com | support.dell.com Switzerland (Geneva) International Access Code: 00 Country Code: 41 City Code: 22 W e bsite: support.euro .dell.com E-mail: T ech_support_central_Europe@dell.com E-mail for F rench-speaking HSB and Corporate Customers: support.
Appendix 137 U.K. (Bracknell) International Access Code: 00 Country Code: 44 City Code: 1344 W ebsite: support.euro .dell.com Customer Care website: support.
138 Appendix www .dell.com | support.dell.com U.S.A. (Austin, T exas) International Access Code: 011 Country Code: 1 Automated Or der-Status Service toll-free: 1-800-433-9014 AutoT ech (portable and d.
Index 139 Index A audio . See sound B badge color , 1 3 battery problems, 3 1 replacing, 1 0 7 BIOS, 113 boot sequence, 118 c h a n g i n g , 118-119 option settings, 1 1 8 booting to a USB device, 1 .
140 Index 140 Index diagnostics Dell, 5 0 lights, 4 7 display . See monitor documentation Dell Dimension Help file, 1 0 Dell Solution Center , 9 End User License Agreement, 1 0 ergonomics, 1 0 F indin.
Index 141 K key bo ard connector , 6 6 problems, 3 5 L labels Microsoft W indows, 1 1 Service T ag, 1 1 lights back of computer , 4 7 diagnostic, 4 7 hard-drive activity , 6 3 M memory 4-GB configurat.
142 Index 142 Index problems (continued) hard drive, 3 3 IEEE 1394, 3 5 Internet, 3 3 keyboar d, 3 5 memory , 3 8 modem, 3 3 monitor hard to r ead, 4 4 monitor is blank, 4 4 mouse, 3 8 network, 3 9 po.
Index 143 troubleshooting Dell Diagnostics, 5 0 diagnostic lights, 4 7 Hardwar e T roubleshooter , 5 7 Help and Support Center , 1 1 restor e to previous state, 5 5 tips, 3 1 TV connect to computer , .
144 Index 144 Index.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Dell XPS GEN 3 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Dell XPS GEN 3 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Dell XPS GEN 3, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Dell XPS GEN 3 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Dell XPS GEN 3, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Dell XPS GEN 3.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Dell XPS GEN 3. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Dell XPS GEN 3 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
