Manuel d'utilisation / d'entretien du produit 917.275632 du fabricant Craftsman
Aller à la page of 52
Owner's Manual CRRFTSMRN ° LAWN TRACTOR 18.5 HP, 42" Mower Electric Start 6 Speed Transaxle Model No. 917.275632 [_ his product has a low emission engine which operates differently from previously built engines.
Warranty ................................................. 2 Safety Rules ........................................... 3 Product Specifications ............................ 6 Assembly/Pre-Operation ........................ 7 Operation .................
IMPORTANT: This cutting machine is capable of amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious injury or death.
II. SLOPE OPERATION Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Opera- tion on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
• Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle. • Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete.
PRODUCT SPECIFICATIONS Gasoline 4.0 Capacity and Unleaded Type: Regular Oil Type SAE 30 (above 32°F) API-SG-SL): SAE 5W-30(below 32°F Oil Capacity: W/Filter: 3.5 Pints W/O Filter: 3.0 Pints Spark Plug: Champion RC12YC (Gap: .030") Ground Speed (MPH): Tire Pressure: Charging System: Battery: Blade Bolt Torque: Forward: 1 st 1.
For Future Use Keys (2) Keys Slope Sheet Your new tractor has been assembled at the factory. When right or left hand is mentioned in this manual, it means when you are in the oper- ating position (seated behind the steering wheel). TO REMOVE TRACTOR FROM CARTON UNPACK CARTON 1.
TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls) 1. Press lift lever plunger and raise attachment lift lever to its highest po- sition. 2. Release parking brake by depressing clutch/brake pedal. 3. Place gearshift lever in neutral (N) position.
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. R N H I1 FAST REVERSE NEUTRAL HIGH LOW CHOKE SLOW IGNITION SWITCH ENGINE OFF RE.
KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
• Attachment Lift Lever High Position For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.
TO OPERATE ON HILLS _,WARNING: Do not drive up or down hills with slopes greater than 15 ° and do not drive across any slope. Use the slope guide at the back of this manual. • Choose the slowest speed before start- ing up or down hills. • Avoid stopping or changing speed on hills.
. Insert key into ignition and turn key clockwise to start position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again.
F,L',. OAT AS YOU COMPLETE REGULAR SERVICE /_r_'_TSERVlOe DATES Check Brake Operation _ Check Tire Pressure Check Operator Presence and T ROS Systems If R Check for Loose Fasteners If I_s if.
TRACTOR Always observe safety ruleswhen per- forming any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.
The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower. To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.
3. Unlock drain valve by pushing inward slightly and turning counterclockwise. 4. To open, pull out on the drain valve. 5. After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.
CLEANING • Clean engine, battery, seat, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with auto- motive type wax.
TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD- UCT SPECIFICATIONS" section of this manual). If tires are over or underinflated, you will not properly adjust your mower.
Mandrel With Parking Brake "Engaged" Mandrel Pulley Nut "A" Jam Nut TO CHECK AND ADJUST BRAKE Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.
Electric Clutch Clutching ----- Idler Stationary J Idler Center Span/_ Keeper _ Transaxle Pulley _ -- Clutch Locator .... , h ...... I1_ Harness TRANSAXLE GEAR SHIFT LEVER NEU- TRAL ADJUSTMENT The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position.
TO REMOVE CABLES, REVERSE ORDER - 1. BLACK cable first from chassis and then from the fully charged battery. 2. RED cable last from both batteries. DD 02614 Weak or Dead Fully Charged Battery Battery REPLACING BATTERY WARNING" Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time.
ENGINE Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.
Immediately prepare your tractor for stor- age at the end of the season or if the trac- tor will not be used for 30 days or more. _ICAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Will not start Hard to start Engine will not turn over Engine clicks but will not start CAUSE 1. Out of fuel. 2. Engine not "CHOKED" properly.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center CAUSE 1. Cutting too much grass/too fast. 2. Throttle in "CHOKE" position. 3. Build-up of grass, leaves and trash under mower. 4. Dirty air filter.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE Mower blades will not rotate Poor grass discharge Headlight(s) not working (if so equipped) Battery will not charge Engine "backfires" when turning engine "OFF" 1.
SCHEMATIC TRACTOR - - MODEL NUMBER 917.275632 BATTERY SOLENOID I IGNITION SWITCH POSITION CIRCUIT "MAKE" OFF M+G+A1 NONE RUN/OVERRID[ B+A1 NONE RUN B+A1 L+A2 START 3 + S + A1 NONE @ J SPARK PLUGS GAP O IGNITION UNIT (2PLUGS ON TW N CYL.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.275632 22 i i i/ I I I I I I 26 40 i I I I i I I I I i I f / 16 i I I ! /1 ! / / ! i / / / 29 55 931 I I I/' I 30.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.275632 KEY PART NO. NO. DESCRIPTION 1 163465 Battery 2 74760412 Bolt, Hex 1/4-20 x 3/4 8 7603J Tray, Battery 10 145211 Bolt, Battery, Front 1/4-20 x 7-1/2 11 15.
TRACTOR - - MODEL NUMBER 917,275632 CHASSIS AND ENCLOSURES 217 9O 31 2094 209 11 209 __ 209 206 chassis-stealth,stlt 33 10_ 209 209 6O 74 54 6O 54 278 209 J 20 59 209 209 209 32.
TRACTOR - - MODEL NUMBER 917.275632 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 174619 Chassis 2 176554 Drawbar 9 193635X428 Dash 10 72140608 Bolt RDHD SQNK 3/8-16 x 1 11 167203 Panel, Dash,.
3-/ / l 34.
TRACTOR - - MODEL NUMBER 917,275632 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 Transaxle Peerless 206-545C 57 130801 (See Breakdown) 59 169691 2 146682 Spring, Return, Brake 61 17120.
STEERING TRACTOR - - MODEL NUMBER 917,275632 / : L _ 38 _39 J J 65 32 28 3O 68 i 13 67 67 67 steering stealth prem 12 36.
STEERING TRACTOR - - MODEL NUMBER 917,275632 KEY PART NO. NO. DESCRIPTION 1 186094X428 Wheel Steering 2 184706 Axle Asm 3 169840 Spindle Asm LH 4 169839 Spindle Asm RH 5 6266H Bearing Race Thrust Harden 6 121748X Washer 25132 x 1-5/8 x 16 Ga.
ENGINE TRACTOR - - MODEL NUMBER 917,275632 78_ 32 3 /3 > 29 38 81 14 23 72 / 62 13 4 OPTIONAL EQUIPMENT Spark Arrester KEY PART NO. NO. DESCRIPTION 1 176636X505 Control Throttle 2 191611 Screw 10 x.
TRACTOR - - MODEL NUMBER 917.275632 SEAT ASSEMBLY 18 .... 15 _j _13 17 I I i I i I i 12 25 11 21 KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 PART NO. 188719 140551 STD523710 19131610 145006 STD541437 124181X 17000616 19131614 182493 166369 174648 DESCRIPTION Seat Bracket Pivot Seat Bolt Fin Hex 3/8-16 unc x 1 Washer 13t32 x 1 x 10 Ga.
DECALS 18 TRACTOR - - MODEL NUMBER 917,275632 11 16 3 13 21 4 11 21 10 24 2O 7 6 15 12 KEY PART NO. NO. 1 187407 2 138047 3 186242 4 186243 5 160396 6 146046 7 179128 9 193561 10 156439 11 189088 12 172331 13 133644 15 187408 KEY PART DESCRIPTION NO. NO.
LIFT ASSEMBLY 11 TRACTOR - - MODEL NUMBER 917,275632 13 4 3 2 5 12 19 13 19 20 ._ 161718 20 _ 20 15 lift-rh, 1 piece25 KEY PART NO. NO. 1 197980 2 198070 3 188822 4 12000002 5 19211621 6 120183X 7 175830 11 139865 12 139866 13 STD624008 15 173288 DESCRIPTION Plunger Assembly Shaft Assembly, Lift Pin, Groove E-Ring Washer 21/32 x 1 x 21 Ga.
TRACTOR - - MODEL NUMBER 917,275632 MOWER DECK °.L I_ 144 _. 45 4oi€ 148 55 34 113 111 2_ 118 _ 5 6 149 J 19 21 2 18 2 29 18 21 23 24 I 25 28 27 .117 42 D elec-t-path stlt 4 42.
TRACTOR - - MODEL NUMBER 917.275632 MOWER DECK KEY PART NO. NO. 1 165892 2 STD533107 3 138017 4 165460 5 STD624008 6 178024 8 850857 9 STD551137 10 140296 11 138971 -- 139775 -- 134149 13 137645 14 12.
TRACTOR - - MODEL NUMBER 917,275632 PEERLESS TRANSAXLE--MODEL NUMBER 206-545C 3,5A 83 18 4 / 26 56 MODEL and SERIAL NUMBERS HERE 79 51 29 35 157 41A ,_7 42.
TRACTOR - - MODEL NUMBER 917.275632 PEERLESS TRANSAXLE--MODEL NUMBER 206-545C KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 772147 2 780086A 3 770128 4 776395 5 776409 6 778364 6A 778369.
TRACTOR - - MODEL NUMBER 917.275632 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0348-E1 I I 1038_ 3_ _307 1019 LABEL KIT II 1330 REPAIR MANUAL I 305A _ 718 ' 8_1_ 358 ENGINE GAS.
TRACTOR - - MODEL NUMBER 917.275632 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0348-E1 1022 1034 6170 914 1095 VALVE GASKET SET 868 _-'_ 1022 276@ 1127_ 1091 141A 947_ 918 977 .
TRACTOR - - MODEL NUMBER 917.275632 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0348-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO.
TRACTOR - - MODEL NUMBER 917.275632 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0348-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO.
50.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. _b ARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face, Do not mow slopes greater than 15 degrees, Make turns gradually to prevent tipping or loss of control.
Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it=yourself.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Craftsman 917.275632 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Craftsman 917.275632 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Craftsman 917.275632, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Craftsman 917.275632 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Craftsman 917.275632, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Craftsman 917.275632.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Craftsman 917.275632. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Craftsman 917.275632 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
