Manuel d'utilisation / d'entretien du produit 917.27475 du fabricant Craftsman
Aller à la page of 56
Owner's Manual CRRFTSMRN ° LAWN TRACTOR 18.5 HP, 42" Mower Electric Start 6 Speed Transaxle Model No. 917.274750 _] his product has a low emission engine which operates differently from previously built engines. Before you start the engine, read and understand this Owner's Manual.
Warranty ................................................. 2 Safety Rules ........................................... 3 Product Specifications ............................ 6 Assembly/Pre-Operation ........................ 8 Operation .................
IMPORTANT: This cutting machine is capable of amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious injury or death.
I1. SLOPE OPERATION Slopes are a major factor related to loss of control and tip-over accidents,which can result in severe injury or death. Opera- tion on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
• Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispensernozzle. • Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete.
PRODUCT SPECIFICATIONS Gasoline 2.0 Capacity and Unleaded Type: Regular Oil Type SAE 30 (above 32°F) 'API-SG-SL): SAE 5W-30(below 32°F Oil Capacity: W/Filter: 3.5 Pints W/O Filter: 3.0 Pints Spark Plug: Champion RC12YC (Gap: .030") Ground Speed Forward: (M PH): 1 st 1.
Steering Wheel insert Steering Boot (1) Hex Bolt _c{ 5/16-18 x 4 Steering Wheel @) Steering Extension Shaft (1) Large Flat Washer a I I u Steering Wheel Adapter (1) 5/16 Lock Washer Seat (1) Washer 17.
Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
7. Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down. 8. Get off seat without moving its ad- justed position. 9. Raise seat and tighten adjustment knob securely. Seat Seat Shoulder Bolts Flat Washer Adjustment Knob CHECK BATTERY 1.
CHECK TIRE PRESSURE The tires on your tractor were overin- flated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. ° Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual.
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. R N H I'.,I REVERSE NEUTRAL HIGH LOW CHOKE FAST 6 G ENGINE OFF REVERSE ENG.
KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
• For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relativelyhigh; the second to desired height. TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operatingposition.
TO OPERATE ON HILLS _,WARNING: Do not drive up or down hills with slopes greater than 15 ° and do not drive across any slope. Use the slope guide at the back of this manual. • Choose the slowest speed before start- ing up or down hills. • Avoid stopping or changing speed on hills.
NOTE: Before starting, read the warm and cold starting procedures below. 5. Insert key into ignition and turn key clockwise to start position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute.
.A,NTENANOE SO.EOULE F,LL, OATES REGULAR SERVICE VICE DATES Check Brake Operation _ Check Tire Pressure Check Operator Presence and T ROS Systems li_ R Check for Loose Fasteners I_ I_s li_ A Sharpen/R.
TRACTOR Always observe safety rules when per- forming any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.
balancer.) NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not. • Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position.
5. After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown. 6. Remove the drain tube and replace the cap onto the end of the drain valve. 7. Refill engine with oil through oil fill dip- stick tube.
MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could cre- ate a fire hazard and/or damage. SPARK PLUG(S) Replace spark plug(s) at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Depress clutch/brake pedal fully and set parking brake. 2. Place gearshift lever in neutral (N) position. 3. Place attachment clutch in "DISENGAGED" position.
TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD- UCT SPECIFICATIONS" section of this manual). If tires are over or underinflated, you will not properly adjust your mower.
Mandrel With Parking Brake "Engaged" Idler Pulleys Mandrel Pulley Nut "A" Jam Nut TO CHECK AND ADJUST BRAKE Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.
Engine Clutching Center ..Span Keeper Stationary Idler Transaxle TRANSAXLE GEAR SHIFT LEVER NEU- TRAL ADJUSTMENT The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows: 1.
TO REMOVE CABLES, REVERSE ORDER - 1. BLACK cable first from chassis and then from the fully charged battery. 2. RED cable last from both batteries. 02614 Weak or Dead Fully Charged Battery Battery REPLACING BATTERY d_IbWARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time.
ENGINE Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.
Immediately prepare your tractor for stor- age at the end of the season or if the trac- tor will not be used for 30 days or more. _CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Will not start Hard to start Engine will not turn over Engine clicks but will not start CAUSE 3ORRECTION 1. Out of fuel. 2. Engine not "CHOKED" properly.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center CAUSE CORRECTION 1. Cutting too much grass/too fast. 2. Throttle in "CHOKE" position. 3. Build-up of grass, leaves and trash under mower. 4. Dirty air filter.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center Mower blades will not rotate PROBLEM CAUSE CORRECTION 1. Remove obstruction. Poor grass discharge Headlight(s) not working (if so equipped) Battery will not charge Engine "backfires '_ when turning engine "OFF" 1.
32.
SCHEMATIC 02831 193372 TRACTOR -- MODEL NUMBER 917.274750 BATTERY m AMMETER FUSE (OPTIONAL) SOLENOID STARTER BLACK GRAY IGNITION s_'_(:_ ARK -, GAP PLUGS UNIT (2 PLUGS O ON TWIN CYL.
ELECTRICAL TRACTOR -- MODEL NUMBER 917.274750 25 34 / / 48 28 27 ', } / /./_'- .............................. ,,,_o_1 .... ..................
ELECTRICAL TRACTOR - - MODEL NUMBER 917.274750 KEY PART NO. NO. DESCRIPTION 1 163465 Battery 2 74760412 Bolt Hex Hd 1/4-20 unc x 3/4 8 176689 Box Battery 16 176138 Switch, Interlock 21 183759 Harness Asm Light W/4152j 22 4152J Bulb Light #1156 24 4799J Cable Battery 6 Ga.
TRACTOR -- MODEL NUMBER 917.274750 CHASSIS AND ENCLOSURES 28 212 261 259 260 258 18 39 278 208 31 _/5 @/5 209 208 / 2_ 206 209 60 209 74 37 ,209 14 -37 208 chassis-Laser -It.
TRACTOR - - MODEL NUMBER 917.274750 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 174619 Chassis 2 176554 Drawbar 5 155272 Bumper Hood/Dash 9 193510X012 Dash 10 STD533710 Bolt, Carriage 3/8-16 x 3/4 11 174996 Panel, Dash, L.H. 13 172105X010 Panel, Dash, R.
TRACTOR - " MODEL NUMBER 917.274750 GROUND DRIVE / 26 27 drive-fender.stlt_38 $8.
TRACTOR - - MODEL NUMBER 917.274750 GROUND DRIVE KEY PART KEY NO. NO. DESCRIPTION NO. 1 Transaxle Peerless 206-545C 62 (See Breakdown) 63 2 146682 Spring, Return, Brake 64 3 123666X Pulley, Transaxle .
TRACTOR -- MODEL NUMBER 917.274750 STEERING ASSEMBLY _2J_39 L i!2--37 _7" --'-'-"-36 15 15 steering pl,lt 57 46 / 10 13 65 68 67 67 67 43 / / 40.
TRACTOR - - MODEL NUMBER 917.274750 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 186780 Steering Wheel 2 184706 Axle Assembly 3 169840 Spindle Assembly, L.H. 4 169839 Spindle Assembly, R.H. 5 626614 Bearing, Race, Thrust, Hardened 6 121748X Washer 25/32 x 1-5/8 x 16 Ga.
ENGINE TRACTOR -- MODEL NUMBER 917.274750 31 29 37 33 38 81 14 23 72 62 13 4 OPTIONAL EQUIPMENT Spark Arrester ÷ngine-bs, lcyF !7 KEY PART NO. NO. 1 170545X505 2 17720408 3 4 137352 13 165291 14 1484.
TRACTOR -- MODEL NUMBER 917.274750 LIFT ASSEMBLY 13 4 3 2 6 11 5 19 13 13 20 20 32 _ 19 _ 15 13 -..........-......._ 31 . 32 Fift-rh.lpiece 3 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 159460 Washer Asm Inner Spring 13 STD624008 W/Plunger 15 173288 2 159471 Shaft Asm.
TRACTOR -- MODEL NUMBER 917.274750 SEAT ASSEMBLY 17 seat It.knob 9 12 I 11 10 8_ 8 6 "/ 21 KEY PART NO. NO. 1 188716 2 180166 3 71110616 4 19131610 5 145006 6 STD541437 7 124181X 8 17000616 9 19131614 10 180186 11 166369 DESCRIPTION Seat Bracket Pnt Pivot Seat (blk) Bolt Fin Hex 3/8-16 unc x 1 Washer 13/32 x 3/4 x 10 Ga.
DECALS TRACTOR -- MODEL NUMBER 917.274750 3 11 11 10 20 13 15 12 13 14 KEY PART NO. NO. KEY PART DESCRIPTION NO. NO. 1 193308 Decal 2 193595 Decal 3 186280 Decal 4 186281 Decal 5 138047 Decal 6 133644 Decal 7 191777 Decal 8 172331 Decal 9 186282 Decal 10 156439 Decal 11 186283 Decal 12 146046 Decal Oper.
TRACTOR -- MODEL NUMBER 917.274750 MOWER DECK 67 il 47 142 117 119 118_ 5 6 1:21 42 D man-t-path stlt 3 16 14-- 18 i i 21 28 29 18 13_ 10_ 9_ 27 46.
TRACTOR - - MODEL NUMBER 917.274750 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 165892 2 STD533107 3 138017 4 165460 5 STD624008 6 178024 8 850857 9 STD551137 10 140296 11 1.
TRACTOR - - MODEL NUMBER 917.274750 PEERLESS TRANSAXLE - - MODEL NUMBER 206-545C _A 47 / 18 4 51 ,52 2g MODEL and SERIAL NUMBERS HERE Model et S_riel i Ch ffre c J 79 42A 48.
TRACTOR - - MODEL NUMBER 917.274750 PEERLESS TRANSAXLE - - MODEL NUMBER 206-5450 REF PART REF PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 772147 2 780086A 3 770128 4 776395 5 776409 6 778364 6A 778.
TRACTOR - - MODEL NUMBER 917.274750 BRIGGS ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0299-E1 I 1330 REPAIR MANUAL I 11329 REPLACEMENT ENGINE I 307_ 358 ENGINE GASKET SET 3@ 12 20@ 617 0 8680 9430 1022 1.
TRACTOR - - MODEL NUMBER 917.274750 BRIGGS ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0299-E1 238 @ ,¢ 35 1022 6170 616_::_ 1022 404 # 914 614 _ 54_ 654 643 1095 VALVE GASKET SET 617 0 1022 868 525 [ 52.
TRACTOR - - MODEL NUMBER 917.274750 BRIGGS ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0299-E1 93_ 692 142_ 117 _1o6 105 _1 9_1°41 137 276 @ 950 108 127 G o47 51 1127 106A F®I 127A 276A@ 947A [_ NIKKI ].
TRACTOR - - MODEL NUMBER 917.274750 BRIGGS ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0299-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 697174 Cylinder Assembly 106 690577 2 399265 Kit-.
TRACTOR - - MODEL NUMBER 917.274750 BRIGGS ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0299-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 310 690323 Bolt (Starter Motor) 851 692424 311 4976.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION LTI O7 ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiii.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Craftsman 917.27475 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Craftsman 917.27475 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Craftsman 917.27475, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Craftsman 917.27475 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Craftsman 917.27475, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Craftsman 917.27475.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Craftsman 917.27475. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Craftsman 917.27475 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
