Manuel d'utilisation / d'entretien du produit 917.27182 du fabricant Craftsman
Aller à la page of 60
Owner's Manual ICRRFTSMRN'I 19.5 HP ELECTRIC START 42" MOWER AUTOMATIC LAWN TRACTOR Model No. 917.271820 • Safety • Assembly • Operation • Maintenance • Repair Parts This product has a low emission engine which operates differently from previously built engines.
Warranty ............................................... 2 Safety Rules ......................................... 3 Product Specifications .......................... 6 Assembly .............................................. 8 Operation ...............
IMPORTANT: This cutting machine is capable of amputating hands and feet and thro.wing, objects. Failure to observe the following safety instructions could result in senous injury or death. I. GENERAL OPERATION • Read, undemtand, and follow all instructions in the manual and on the machine before starting.
III. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Keep children out of the mowing area and under the watchful care of another responsible adutt.
• Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. • Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope. • If machine stops while going uphill, disengage blades, shift into reverse and back down slowly.
PRODUCT SPECIFICATIONS GASOLINE 3.5 GALLONS CAPACITY UNLEADED ANDTYPE: REGULAR OILTYPE SAE 30 API-SF-SJ): (ABOVE 32°F) SAE 5W-30 (BELOW 32°F) OIL CAPACITY: 3.0PINTS SPARK PLUG: CHAMPION GAP: .030") RJ19LM OR Jt9LM VALVE INTAKE: .004"-.006" ADJUSTMENT EXHAUST: .
Steerin( Wheel Swt_l:rePg l Adapter Steering Sleeve I teering Extension Shaft (1) Hex Bolt 3/8-16 x 1 (1)Large Flat Washer Wheel Inse_ © (1) Hex Bolt 5/16-18 x 1-1/4 (1) Lock washer 3/8 @ (1) Locknut.
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
INSTALL SEAT Adjust seat before tightening adjustment knob. 1. Remove adjustment knob and flat washer securing seat to cardboard packing and sat aside for assembly of seat to tractor. 2. Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.
CHECKTIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual.
t#CHECKLIST BEFORE YOU OPERATE AND ENJOY YOUR N EW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVlEWTHE FOLLOWING CHECKLIST: ,I All assembly instructions have been completed. ,,/No remaining loose parts in carton.
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR REVERSE FORWARD FAST SLOW WARNING ENG,NEON ENG,NEOFF O'LFRESSURE L,G.
KNOWYOURTRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiadze yourself with the locations of various controls and adjustments. Save this manual for future reference.
( HOWTO USEYOURTRACTOR TO SET PARKING BRAKE Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the operator to Seave the seat without first setting the parking brake will shut off the engine. 1. Depress clutch/brake pedal into full "BRAKE" position and hold.
These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed. • The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.
• Do not push or tow tractor at more than two (2) MPH. • To reengage transmission, reverse above procedure. NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.
WARM WEATHER STARTING (50 ° F and above) 8. When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.
MOWINGTIPS • Mower should be properlyleveled for best mowingperformance. See "1"O LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has been cut.
MAINTENANCE SCHEDULE FILL IN OATES AS YOU COMPLETE REGULAR SERVICE Check Brake Operation _ check _r _ence and inled_k Systems Lu_k:atlon Chart Check Batlery Level Clean Battmy ar_ Temdneis CheCk Trans.
TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be ad- justed, (_ee "TO ADJUST BRAKE" in the Service and Adjustments section of this manual).
NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to "leak" power.
Oil Drain Valve Closed and Locked/ Poslion_.:: Cap "_ Drain Tube CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.
CLEANING i Clean engine, batten/, seat, finish, etc. of all foreign matter. Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automo- tive type wax.
TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or ddveway. Make sure tires are propedy inflated (See "PROD- UCT SPECIFICATIONS" section of this manual). If tiros are over or underinflated, you will not properly adjust your mower.
Mandrel Idler Pulleys Mandrel Pulley TO ADJUST BRAKE Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle. If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.
MotionControl Neutral Lock Gate ,ever Adjustment Bolt TRANSMISSION REMOVAl/REPLACE- MENT Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See "PURGE TRANSMISSION" in the Operation section of this manual.
Positive terminal must be connected first to prevent sparking from accidental grounding. 1. Lift hood to raised position. 2. Remove terminal guard. 3. Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor. 4. Install new battery with terminals in same position as old battery.
3. Choke should be closed. If it is not, loosen casing clamp screw and move choke cable until choke is completely closed. Tighten casing clamp screw securely. 4 Reassemble air cleaner. Clamp Quartor Choke Clos_ Casing _*=_i_i TO ADJUST CARBURETOR The carburetor has been preset at the factory and adjustment should not be necessary.
Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. _l_ CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART PROBLEM Will not start Hard to start Engine will not turn over CAUSE 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded. 4. Bad spark plug. 5. Dirty air filter. 6. Dirty fuel filter. 7. Water in fuel. 8.
TROUBLESHOOTING CHART CAUSE ;ORRECTION :PROBLEM Loss_power _ontinued) Excessive vibration Enginecontlnues to run when operator leaves seat with attachment clutch engaged Poor cut - uneven Mower blades will not rotate 3. Build-up of grass, leaves and trash under mower.
TROUBLESHOOTING CHART PROBLEM CAUSE Poor grass 1. Engine speed too slow. discharge 2. Travel speed too fast. 3. Wet grass. 4. Mower deck not level. 5. Low/uneven tire air pressur_ 6. Worn, bent or loose blade. 7. Buildup of grass, leaves an_ trash under mower.
SCHEMATIC TRACTOR -- MODEL NUMBER 917.271820 BATTERY AMMETER (OPTIONAL) IGNmON SWITCH POSITION CIRCUIT "MAKE- OFF M+G+A1 NONE START B÷S÷A1 NONE RUN_.IGHT B+AI A2+L RUN B-_AI NONE NOTE YOUR TRACTOR IS EQUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT CONNECTED TO THE BATTERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.271820 34.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.271820 KEY PART NO. NO. DESCRIP_ON 1 2 8 lO 11 12 16 21 22 24 25 26 27 28 29 3o 33 40 41 42 43 45 52 55 163465 Battery 74760412 Bolt, Hex 1/4-20 x 3/4 7603J Tra.
TRACTOR - - MODEL NUMBER 917.271820 CHASSIS AND ENCLOSURES 28 P 12 204 11 74 36.
TRACTOR - - MODEL NUMBER 917.271820 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 169830 Chassis 2 169061 3 17060612 S_rew 3/8-16 x 3/4 5 155272 Bumper Hoo_Dnsh 9 168337X013 Dash 10 STD533710 .
GROUND DRIVE TRACTOR "- MODEL NUMBER 917.271820 38.
TRACTOR -- MODEL NUMBER 917,271820 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRiPTiON NO. NO. DE$CRtPTION t ...... Transaxle (See Breakdown) 64 71170764 BOll Hex 7/16-20 x 4 Gr.
TRACTOR - - MODEL NUMBER 917.271820 STEERING ASSEMBLY _l_l _ d': 40.
TRACTOR - - MODEL NUMBER 917.271820 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION I 139768 Stsedng Wheel 2 154427 Front Axle Assembly 3 169840 Spindle Assembly, L.
ENGINE TRACTOR - - MODEL NUMBER 917,271820 31 39 2 1_ IP 14 38 32 33 33 29 OPTIONAL EQUIPMENT Spark Arrester 13 _10 i 12 42.
ENGINE TRACTOR - - MODEL NUMBER 917.271820 KEY PAITT NO. NO. DESCRIPTION 1 2 3 4 5 6 7 8 10 11 12 13 14 16 17 23 25 26 27 29 31 32 33 34 37 38 39 45 81 t7(_47 Control Throt Paddle 17720410 Screw Hex Thd Cut 1/4-20x5/8 T ....... Engine (See Breakdown) Bdggs Model No.
TRACTOR "" MODEL NUMBER 917.271820 sEAT AssEMBLY KEY pART NO. NO. DEECR|PT|ON 2 140551 _-_ F_n Hex 3/8-16ur_ X I 71110616 _i 3 t9131610 Washer 13_2 X 3_4 X 10 GS STD541437 r_u_ r_°_.. ="_". C._=,_ 2 250 BIk ZI 6 91X Spdng _e-L P-' 7 1241 ^.
DECALS TRACTOR - - MODEL NUMBER 917.271820 2 7 2 4 14 20 22 14 13 KEY PART NO. NO. 1 156439 2 177253 3 171696 4 171697 5 176681 6 133644 7 171809 9 1632O4 11 156811 13 146046 14 177265 DESCRIPTION De.
TRACTOR - - MODEL NUMBER 917.271820 LIFT ASSEMBLY 2O 15 15 46.
TRACTOR . - MODEL NUMBER 917.271820 LIFT ASSEMBLY KEY PART NO. NO. DESCRIPTION I 2 3 4 5 6 7 8 11 12 13 15 16 17 18 19 2O 31 32 159460 Lilt Lever Inner Wire Asm. 159471 Shaft Asm. Lift 1G5767X Pin Groove 12O02O(_ ERIng 19Ql1621 Washar 21/32 x 1 x21 Ga.
TRACTOR - - MODEL NUMBER 917.271820 MOWER DECK 158 157 _ _,_ 67 183 1_ s 159_ 34 144 45 14S 21 22 18 48.
TRACTOR - - MODEL NUMBER 917.271820 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 165892 Mower Hous;ng 59 141043 2 STt3533107 Bolt 67 149846 3 138017 Bracket Assembly,Sway Bar.
TRACTOR -- MODEL NUMBER 917.271820 HYDRO GEAR TRANSAXLE - - MODEL NUMBER 3140510 50.
TRACTOR - - MODEL NUMBER 917,271820 HYDRO GEAR TRANSAXLE - - MODEL NUMBER 314-0510 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO, DESCRIPTION 1 "_70351 Ma_n HousiP_, Assembly 59 170408 Rotor, Brak.
TRACTOR - - MODEL NUMBER 917.271820 BRIGGS & STRATTON ENGINE-MODEL NUMBER 461707, TYPE NUMBER 0145-E3 1125 1095 VALVE OVERHAUL GASKET SET 220 _ 1132 _ 741_ 1de I_ 19 G 634 e 552A 552 4040 2911_ 1 1019LABEL KIT I 1 lO. OWNER'S MANUAL ] lit REO_JIRE$S_CIAL 1OOLS 15 _ TO INSTALL SEE REPAIR INSTRUCTION MANUAL.
TRACTOR -- MODEL NUMBER 917.271820 BRIGGS & STRA'rTON ENGINE-MODEL NUMBER 461707, TYPE NUMBER 0145-E3 51 _ 447 Ik, _ 304 725 _ 240 _ 7 573NN__ _ J I 432_ 392_)104_.
TRACTOR - - MODEL NUMBER 917.271520 BRIGGS & STRATTON ENGINE-MODEL NUMBER 461707, TYPE NUMBER 0145-E3 697 3o91 5101 513 783 1051 _' y 803 544 802 797 801 358 GASKET SET 634 1770 51A_ 163_ 905.
TRACTOR - - MODEL NUMBER 917.271820 BRIGGS & STRATTON ENGINE-MOOEL NUMBER 461707,TYPE NUMBER 0145-E3 KEY PART KEY PART NO. NO. DESCRtPTtON NO. NO, OESCRIPTION 1 498583 Cylinder Assembly 95 690716 Screw (Thrott_ Valve) 2 399265 Bushing/Seal Kit 97 693485 Sheft-Throte 3 391086 * Seal-Oil 98 807923 Kit-Idle Speed 4 493304 Sump.
TRACTOR - - MODEL NUMBER 917.271820 BRIGGS & STRATTON ENGINE-MODEL NUMBER 461707,TYPE NUMBER 0145-E3 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 307 94930 Screw (Cylinder Shield) 797.
57.
58.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ut QD ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 6 Operate your Tractor up and down the face of slopes (not greater than 15 °) never across the face. Make turns gradu- I ally to prevent Upping or loss of control.
Get it fixed, at your home or ours! For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOME sM Anytirne,day or night (1-800-469-4663) www.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Craftsman 917.27182 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Craftsman 917.27182 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Craftsman 917.27182, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Craftsman 917.27182 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Craftsman 917.27182, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Craftsman 917.27182.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Craftsman 917.27182. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Craftsman 917.27182 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
