Manuel d'utilisation / d'entretien du produit 137.24884 du fabricant Craftsman
Aller à la page of 30
Operator's Manual ® 10 in. TABLE SAW Model No. 137.248840 CAUTION: Before using this Table Saw, read this manual and follow all its Safety Rules and Operating Instructions ® Safety Instructions ® Installation ® Operation ® Maintenance ® Parts List Customer Help Line 1 o800o843ol 682 Sears, Roebuck and Co.
SECTION PAGE Warranty ............................................................. 2 Product Specifications ........................................ 2 Power Tool Safety .............................................. 3 Table Saw Safety ...............
la, WARNING n Before using your tabJe saw, it is critical that you read and understand these safety rules. Failure to follow these rules couJd result in serious injury or damage to the table saw. Good safety practices are a combination of common 16. REMOVE ADJUSTING KEYS AND WRENCHES.
1. ALWAYS USE SAW BLADE GUARD, splitter and anti-kickback pawls forevery operation for which they can be used, including through-sawing. Through-sawing operations are those in which the blade cuts completely through the workpiece when ripping or cross-cutting.
GROUND(NG (NSTRUCT(ONS IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least resistance for electric currents and reduces the risk of electric shock. This tool is equipped with an electrical cord that has an equipmentogrounding conductor and a grounding p(ug.
RECOMMENDED ACCESSORIES IA WARNING I Visit your Scars Hardware Department or see the Scars Power and Hand TooJ Catalog to purchase recommended accessories for this power tool IA WARNING n To avoid the risk of personal injury, do not modify this power tool or use accessories not recommended by Sears.
UNPACKING YOUR TABLE SAW A B G H C D ®® M O P Q o 0 0 U R S V W X.
Blade Guard # Extension Wing Locking Overload Reset Switch Blade Tilt Pointer & Scale ON/OFF Switch with Saftey Key Blade Elevation Handwheel Table insert Rip Fence Side Table Extension Wing Bevel.
ANTFKICKBACK PAWLS = Prevents the work piece from being kicked upward or back toward the front of the table saw by the spinning blade. ON/OFF SWITCH = Contains a built-in safety switch key. To lock the switch in the OFF position, remove the switch key from the switch.
ASSEMBLE STAND (FIG. A) 1 Unpack all parts and group by type andsize Refer to the parts !istfor correct quantities 2 Attach onelong upper support (S)to top of leg(V) using onebolt (1) andnut (2) NOTE:.
MOUNT SAW ONWORK SURFACE (FIG. C) 1. If the legsetwill not beused, the sawmust be properly secured to a sturdy workbench using the four mounting holes at the base of the saw.
RIP FENCE (Fig, G) 1. Lift upward on the ripfence handle (1) so the rear holding clamp (2) is fully extended. 2. Place the rip fence on the saw table, lowering the front of the fence onto the table first. 3. Push down on the fence handle (1) to lock. Fig.
BLADE GUARD ASSEMBLY (FIG. K, L, M) 1. Setthe blade to maximum height and the tilt to zero degrees on the bevel scale with the hand wheels. Lock the blade bevel lock knob. 2. Place the spring washer (2), flatwasher (3), external tooth lock washer (4) ontotheblade guard mounting bolt (1) (Fig.
iNSTALLiNG THE TABLE SIDE EXTENS!ONS- cont'd (FIG. O} 6. Snap one short location seat (1) over the end of the rear table extension tube (2). Make sure the locating pin (3) in the location seat fits into the matching hole in the extension tube (Fig.
RiP FENCE iNDiCATOR ADJUSTMENT (FIG. Q) 1_ The rip fence indicator (6) points to themeasurement scale. The scale shows the distance from theside of the fence to nearest side of the blade.
BLADE PARALLEL TOTHE MITER GAUGE GROOVE (FIG. U, V) I_WARNiNG This adjustment was made at the factory, but it should be rechecked and adjusted if necessary. IA waRninG n To prevent personal injury: o Always disconnect plug from the power source when making any adjustments.
8ASmC SAW OPERATmONS RAISE THE BLADE (FIG. W) To raise or lower the blade, turn the blade elevation handwheel (1) to the desired blade height, and then tighten lock handle (2) to maintain the desired blade angle. Fig. W 2 TILTING THE BLADE (FIG. W) 1.
CUTTING OPERATIONS There are two basic types of cuts: ripping and crosscutting. Ripping is cutting along the length andthe grain of the workpiece. Crosscutting is cutting either across the width or across the grain of the workpiece. Neither ripping nor crosscutting may be done safely freehand.
REVEL RiPPiNG This cutis the same as ripping except the blade bevel angle is set to an angle other than "0". la, WARNING n Cut only with the workpiece and the fence on the right aide of the blade. RiPPiNG SMALL PIECES IA wAR.I.G n Avoid injury from the blade contact.
COMPOUND MITER CROSSCUTTING (FIG. FF) 0°~45 ° BLADE BEVEL & 00~45 ° MITER ANGLE This sawing operation is combining a miter angle with o bevel angle.
Attach auxiliary fence to ripfence withtwo "C"clamps. (Fig. dd) Fig. JJ DADO CUTS (FIG. KK) IA WARNING n a. Only Stackable dado blades can be used on this SaW. b. DO NOT use Adjustable or Wobble type dadoes. c. Maximum dado cut width is 1/2 in.
GENERAL MAINTENANCE IA WARNING n For your own safety, turn the switch OFF and remove the switch kay. Remove the plug from the power source outlet before maintaining or lubricating your saw. 1. Clean out al! sawdust that has accumulated inside the saw cabinet and the motor.
IA WARNmNG n To avoidinjury from an accidental start, turn theswitch "OFF" and always remove the plug from the power source before making any adjustments_ ® Consult your !ocal Sears Service Center if for any reason the motor wil! not run. SYMPTOM Saw will not starL iDoes not make accurate 45 ° _nd 90 ° rip cuts.
t0 in. TABLE SAW MODEL NO. t37.248840 [A WAR.I.G [ When servicing use only CRAFTSMAN replacement parts. Use of any other parts many create a HAZARD or cause product damage. Any attempt to repair or replace electrical parts on this Table Saw may create a HAZARD unless repair is done by a qualified service technician.
10 in. TABLE SAW MODEL NO. 137.248840 SCHEMATIC FOR SAW [ [ [ OKAP OBCW 2 2179 09JK OB3R 0J76 0JAA _" IOGP / V 20KA 2CWN 0J76 OBPA OBAE_ 0B99 OKMR.
10 in. TABLE SAW MODEL NO. 137.248840 PARTS LIST AND SCHEMATIC FOR STAND I.D. NO DescripJJon Size 09D6 FOOT PAD 0A4T FENCE STORAGE CLiP 0EAA BRACKET #AW 0EAN UPPER SUPPORT #AW 0EAP UPPER SUPPORT #AW 0.
10 in. TABLE SAW MODEL NO. 137.248840 PARTS LIST AND SCHEMATIC FOR MOTOR i.D. NO Descdp_ion 0HV8 BALL BEARING 0HVU BALL BEARING 0HXg NEEDLE BEARING 0JAL EXT.TOOTH LOCK WASHER 0JX3 HEX. SOC. SET SCREW 0K3A CR,RE. PAN HD. SCREW & WASHER 0KSV CR,-RE.
PUSH STICK CONSTRUCTION ® This is a full°size drawing (actual size) ® Use good quality plywood or sotid wood ® Use %" or ¾" material e Push stick MUST be thinner than the width of mater.
.
Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who soJd it! For the replacement parts, accessories and Operator's Manuals that you need to do-it-yourself.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Craftsman 137.24884 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Craftsman 137.24884 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Craftsman 137.24884, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Craftsman 137.24884 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Craftsman 137.24884, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Craftsman 137.24884.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Craftsman 137.24884. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Craftsman 137.24884 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
