Manuel d'utilisation / d'entretien du produit 10500 du fabricant 3M
Aller à la page of 44
TM AccuGlide ™ is a Trademark of 3M, St. Paul, MN 55144-1000 Litho in U.S.A © 3M 2005 44-0009-2049-4( B ) AccuGlide 2+ S tainless S teel 2 Inch Upper and Lower T aping Heads T ype 10500 Instructions and Parts List Serial No. _____________________________________ For reference, record taping head(s) serial number(s) here.
.
Replacement Parts and Service Information T o Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch ® equipment you ordered. It has been set up and tested in the factory with Scotch ® t apes. If technical assist ance or replacement p art s are needed, call or fax the appropriate number listed below .
.
Replacement Part s and Service Information T o Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch ® equipment you ordered. It has been set up and tested in the factory with Scotch ® t apes.
.
Instruction Manual AccuGlide ™ 2+ Stainless Steel 2 Inch Upper and Lower Taping Heads Type 10500 Table of Contents Page Equipment Warranty and Limited Remedy .......................................................................................... .
Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FIT.
1 AccuGlide™ 2+ Stainless Steel 2 Inch Upper Taping Head , Type 10500 Intended Use The intended use of the AccuGlide ™ 2+ Stainless Steel 2 Inch Upper and Lower Taping Heads is to apply a "C" clip of Scotch ® pressure-sensitive film box sealing tape to the top and/or bottom center seam of regular slotted containers.
2 Import ant Safeguards This safety alert symbol identifies important safety messages in this manual. READ AND UNDERSTAND THEM BEFORE INSTALLING OR OPERATING THIS EQUIPMENT. Explanation of Signal Word Consequences Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury and/or property damage.
3 Import ant Safeguards (Continued) Important – In the event the following safety labels are damaged or destroyed, they must be replaced to ensure operator safety . See "Replacement Parts Illustrations and Parts Lists" for label part numbers.
4 S pecifications 1. Tape: For use with Scotch ® pressure-sensitive film box sealing tapes. 2. Tape Width: 36 mm or 1-1/2 inches minimum to 48 mm [2 inches] maximum. 3. Tape Roll Diameter: Up to 405 mm [16 inches] maximum on a 76.2 mm [3 inch] diameter core.
5 Figure 2-1 – Dimensional Drawing S pecifications (Continued).
6 Inst allation 1. The box conveying system must positively propel the box in a continuous motion, not exceeding 0.40 m/s [80 feet per minute], past the taping head assembly since the box motion actuates the taping mechanism.
7 Operation Figure 3-1 – Taping Head Components/Threading Diagram, Upper Head (Left Side View) Figure 3-2 – Taping Head Components/Threading Diagram – Lower Head (Left Side View).
8 It is recommended that the detailed instructions and sketches in this manual be referred to the first few times the taping head is loaded/threaded until the operator becomes thoroughly familiar with the tape loading operation. Note – Remove tape roll before removing taping head from machine to minimize weight.
9 Operation (Continued) Manually turn tape roll to create slack tape while pulling threading needle through tape applying mechanism until needle is through and tape is in alignment with applying roller. Excess tape can be cut with a scissors at applying roller.
10 The AccuGlide™ 2+ Stainless Steel Taping Head has been designed for long, trouble free service. The taping head will perform best when it receives routine maintenance and cleaning. Taping head components that fail or wear excessively should be promptly repaired or replaced to prevent damage to other portions of the head or to the product.
11 Maintenance (Continued) Applying/Buffing Roller Replacement Replacing roller requires removal of shaft and mounting screws. With no area on the shaft to grip, the shaft often turns when attempting to remove the second screw.
12 Tape Drum Friction Brake – Figure 5-3 The tape drum friction brake on each taping head is pre-set for normal operation to prevent tape roll over travel. Should tension adjustment be required, turn the self-locking nut on the shaft to vary compression of the spring.
13 Adjustment s (Continued) Applying Mechanism Spring To obtain access to the spring, remove the taping head cover (four mounting screws). Replace cover when finished. The applying mechanism spring, shown in Figures 5-4A and 5-4B, controls applying and buffing roller pressure on the box and returns the mechanism to the reset position.
14 Adjustment s (Continued)| Figure 5-6 – Leading Tape Leg Length Figure 5-7 – Changing Tape Leg Length • To reduce the risk associated with shear, pinch, and entanglement hazards: − Turn air .
15 (Continued) T roubleshooting Cause The tape is threaded incorrectly The tape tension is too low The knurled roller drags Tape tracks to one side or drags on the support tabs of applying frame The o.
16 Problem Tape is tabbing on the trailing leg on the back of the box The tape end does not stay in application position in front of the applying roller Tape not centered on box seam Cause There is ex.
17 S p are Parts/Service Information Recommended Spare Parts A set of spare parts that will periodically require replacement due to normal wear is supplied with the taping heads. The set includes the following which should be reordered when used to keep the taping heads in production: AccuGlide ™ 2+ Stainless Steel 2 Inch Upper Taping Head Qty.
18 Replacement Part s Illustrations and Parts List s AccuGlide™ 2+ Stainless Steel 2 Inch Upper Taping Head, Type 10500 AccuGlide™ 2+ Stainless Steel 2 Inch Lower Taping Head, Type 10500 1. Refer to the Taping Head Assemblies Figure to find all the parts illustrations identified by figure numbers.
19 T aping Head Assemblies – AccuGlide™ 2+ St ainless Steel 2 Inch.
20 Figure 10518 – Upper Head.
21 Figure 10518 – 2" Upper Head Ref. No. 3M Part No. Description 10518-1 78.8134.2346.0 Frame - Tape Mount Upper Assy 10518-2 78.8134.2347.8 Frame - Front Upper Assy 10518-3 78-8068-4143-9 Guide - # 1 10518-4 78-8068-4144-7 Guide - # 2 10518-5 78-8134-2348-6 Screw - Hex.
22 Figure 10519 – Upper and Lower Heads.
23 Figure 10519 – 2" Upper and Lower Heads Ref. No. 3M Part No. Description 10519-1 78-8134-2359-3 Applying Arm # 1 10519-2 78-8134-2360-1 Applying Arm # 2 10519-3 78-8134-2361-9 Plate - Tape 1.
24 Figure 10520 – Upper Head.
25 Figure 10520 – 2" Upper Head Ref. No. 3M Part No. Description 10520-1 78-8134-2366-8 Buffing Arm - R/H 10520-2 78-8134-2367-6 Buffing Arm - L/H 10520-3 78-8134-2368-4 S h af t - Roller 10520.
26 Figure 10521 – Upper and Lower Heads.
27 Ref. No. 3M Part No. Description 10521-1 78-8134-2372-6 Link - Arm Assy, R/H 10521-2 78-8134-2373-4 Link - Arm Assy, L/H 10521-3 78-8134-2374-2 Shaft - Pivot 10521-4 78-8134-2375-9 Bearing - Special 30 mm 10521-5 78-8060-8241-4 Screw - Bearing Shoulder 10521-6 78-8060-8204-2 Screw - Hex.
28 Figure 10522 – Upper and Lower Heads.
29 Figure 10522 – 2" Upper and Lower Heads Ref. No. 3M Part No. Description 10522-1 78-8134-2376-7 Frame - Cut-off Weldement 10522-2 78-8060-8419-6 Blade - 65mm/2.56 Inch 10522-3 78-8060-8342-0 Screw - Hex.Hd., M5 x 8 10522-4 78-8134-2377-5 Blade Guard Assy.
30 Figure 10523 – Upper and Lower Heads 4 14.
31 Figure 10523 – 2" Latch Upper and Lower Heads Ref. No. 3M Part No. Description 10523-1 78-8134-1936-9 Bracket - Tape Drum 10523-2 78-8134-1937-7 Shaft - Tape Drum 50mm 10523-3 78-8134-1938-5.
32 Figure 10524 – Lower Head.
33 Figure 10524 – 2" Lower Head Ref. No. 3M Part No. Description 10524-1 78-8134-2385-8 Frame - Tape Mount Lower Assy 10524-2 78-8134-2386-6 Frame - Front Lower Assy 10524-3 78-8068-4144-7 Guide - # 2 10524-4 78-8068-4143-9 Guide - # 1 10524-5 78-8134-2348-6 Screw - Hex.
34 Figure 10525 – Lower Head.
35 Figure 10525 – Lower Head Ref. No. 3M Part No. Description 10525-1 78-8134-2367-6 Buffing Arm - L/H 10525-2 78-8134-2366-8 Buffing Arm - R/H 10525-3 78-8134-2368-4 S h af t - Roller 10525-4 78-80.
THIS P AGE IS BLANK.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté 3M 10500 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du 3M 10500 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation 3M 10500, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le 3M 10500 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le 3M 10500, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du 3M 10500.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le 3M 10500. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei 3M 10500 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
