Manuel d'utilisation / d'entretien du produit PA-4C-E 1 du fabricant Cisco Systems
Aller à la page of 40
Americas Headquarters: © 20 07 Cisco Systems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA PA-4C-E 1-Port High-Performance ESCON Channel Port Adap.
2 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preface Preface This preface describes the objecti ves and or ganization of this document and explains ho w to f ind additional information on related products and services.
3 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preface Related Documentation Y our router , switch, or gatew ay and the Cisco IOS software runni.
4 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preface http://www .cisco.com/en/US/docs/general/whatsnew/whatsne w .
5 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Overview Overview This section describes the HP ESCON P A, including channel attachment, the LED .
6 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Overview Y ou can install the HP ESCON P A in any of the av ailable port adapter slots in a Cisco 7200 series router . Figure 2 shows an HP ESCON P A installed in port adapter slot 1 of a Cisco 7206.
7 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Overview • For general information on HP ESCON P A microcode, refer to the “HP ESCON P A Microcode Overvie w” section on page 12 .
8 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Overview Figure 3 shows the LED indicators. Figur e 3 HP ESCON P A LED Indicators T able 2 shows the HP ESCON P A LED indicator sequences during a cold boot.
9 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Overview ESCON Cable The ESCON channel interface uses 62.5/125 micrometer , multimode, f iber-optic cable with male duplex connectors at each end ( Figure 5 ).
10 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Overview Figur e 6 P ort Adapt er Slots in the Cisco 7206 Router Identifying Interface Addresses This section describes how to identify the interf ace addresses for the port adapter slots and ESCON channel port numbers.
11 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Overview T able 3 describes the interface addresses for the Cisco 7200 series routers, includingCisco 7200 VXR routers.
12 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation Preparing for Installation This section describes the general equipment, safety , and site preparation requirements for installing the HP ESCON P A.
13 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation The following e xample is a partial display of the show microcode com.
14 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation T able 4 lists the specif ic Cisco IOS software images that are compatible with the HP ESCON P A. T able 5 specif ies the recommended minimum lev el of HP ESCON P A microcode for the corresponding Cisco IOS release.
15 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation Safety Guidelines This section provides safety guidelines that you should follo w when working with any equipment that connects to electrical power or telephone wiring.
16 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr . Sie bef inden sich in einer Situation, die zu Verletzungen führen kann.
17 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation V arning! VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du bef inner dig i en situation som kan leda till personskada.
18 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation Electrical Equipment Guidelines Follo w these basic guidelines when w.
19 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation Class 1 laser products are not considered hazardous. The HP ESCON P A has embedded Class 3a laser LED assemblies operating at a nominal wa velength of 850 nanometer and a maximum potential output po wer of 1.
20 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation Staring into Laser Beam Warning Do not stare into the laser beam. Statement 1010 Waarschuwing Niet in de straal staren. V aroitus Älä katso säteeseen.
21 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Removing and Installing Port Adapters Removing and Installing Port Adapters This section describes how to remo ve port adapters from supported platforms and also how to install ne w or replacement port adapters.
22 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Removing and Installing Port Adapters Online Insertion and Removal The Cisco 7200 series routers, including Cisco 7200 VXR routers, support online insertion and remov al (OIR) of all port adapters.
23 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Removing and Installing Port Adapters Port Adapter Removal and Installation In this section, the illustrations that follow gi ve step-by-step instructions on ho w to remove and install port adapters.
24 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Removing and Installing Port Adapters Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Removing and Installing a Port Adapter Step 1 To remove the port adapter, place the port adapter lever in the unlocked position.
25 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Removing and Installing Port Adapters Attaching the HP ESCON PA to the Channel Caution W e recommend that an authorized service representativ e or other qualif ied service person perform the follo wing procedure.
26 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Configuring the HP ESCON PA T o continue your port adapter installation, you must conf igure the HP ESCON P A interface.
27 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Configuring the HP ESCON PA Interface After you verify that the ne w HP ESCON P A is installed correctly , use the conf igure command to conf igure the new interf aces.
28 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Step 2 At the prompt, enter the interface conf iguration mode by using the interface conf iguration command.
29 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Step 3 Specify one of the new interf aces with the show interfaces port adapter type slot/interface command and verify that the f irst line of the display specif ies the interface with the correct slot number .
30 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA X.25 software, Version 3.0.0. 4 Ethernet/IEEE 802.3 interface(s) 3 FastEthernet/IEEE 802.3 interface(s) 2 IBM channel interface(s) 125K bytes of non-volatile configuration memory.
31 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Using the show diag Command Display the type of port adapter installed in your system using the show diag command.
32 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Data transfer rate 12 Mbytes, number of subchannels 0 Last input 00:.
33 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Upgrading Your HP ESCON PA Microcode The following sections discuss .
34 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Step 4 Reconf igure the router , as necessary , to use the HP ESCON P A microcode image stored in the Flash memory card in slot 0 or slot 1, or in the SanDisk memory device in disk 0 or disk 1.
35 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA 18 .. unknown BC7BEC5D 51EB90 17 246184 Sep 18 2000 06:46:56 xcpa218-6_seg_802 19 .. unknown C09633A6 5A8284 18 562804 Sep 18 2000 06:47:09 xcpa218-6_seg_cmpc 20 .
36 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Step 5 T o verify that the correct microcode is loaded according to the ne w instructions, enter the show contr ollers EXEC command.
37 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA 4109312 bytes copied in 206.
38 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA In the squeeze command display output, the displayed characters hav e the follo wing meaning: • The character “e” means the Flash memory special location has been erased, which occurs before a write operation.
39 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Expanding disk0:xcpa27-1_seg_push (15488 bytes):!!!!!!!!!!! Expandin.
40 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA This document is to be used in conjunction with the documents listed in the Preparing for Installation section. Copyright © 2003-2007 Cisco Systems, Inc.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Cisco Systems PA-4C-E 1 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Cisco Systems PA-4C-E 1 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Cisco Systems PA-4C-E 1, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Cisco Systems PA-4C-E 1 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Cisco Systems PA-4C-E 1, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Cisco Systems PA-4C-E 1.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Cisco Systems PA-4C-E 1. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Cisco Systems PA-4C-E 1 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
