Manuel d'utilisation / d'entretien du produit Engine 611 du fabricant Cisco Systems
Aller à la page of 14
Corporate Headquarters: © 20 05 Cisco Syst ems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Installing Hard Disk Drives in the Cisco Wide Area Ap.
2 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Safety Overview Protecting Against Electrostatic Discharge Static electricit y can harm delicate componen ts insi de the de vice.
3 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Introduction Introduction The W AE-611 supports two 1-inch (2 .54-cm) slim 3.5-inch (8.89-cm) lo w voltage dif ferential (L VD) hard disk dri ves. The W AE-611 requires SCSI hard disk dri ves.
4 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Removing the Bezel and Cover Removing the Bezel and Cover War ni ng Before working on a sy stem that has an on/off switch, turn OFF the po wer and unplug the power cord.
5 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Removing the Beze l and Cover Figur e 2 Removing the Co v er Step 5 Slide the cov er back. Lift it up and of f the device. Caution For proper cool ing and airflo w , replace the cover before tu rning on the de vice.
6 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Assigning SCSI IDs Figur e 3 Location of Dr ive Ba ys Behind the Bez el Assigning SCSI IDs When you install or replace one or more of the SCSI disk dri v es in a W AE-611, you must assign a SCSI ID to each disk dri ve.
7 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Removing and Repl acing a SCS I Hard Disk Dri ve Figure 4 Hard Disk Dr ive Connec tors and SCSI ID Jumper Pins Step 2 T o check whether the configuration is correct, refer to the b oot time messages on th e de vice consol e.
8 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Removing and Replac ing a SCSI Hard Disk Drive Step 3 Po wer do wn the de vice and peripheral de vices, and disconnect the po w er cord and all external cables. Step 4 Press the release tabs on the bezel, and pull the bezel a way from the chassis.
9 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Replacing the Cover and B ezel and Completin g the Installation Step 11 Connect the power and SCSI cables to the dri ve. If you disconnected the IDE cable to the CD-R OM, reconnect it.
10 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Obtaining Documentation T o complete your instal lation, follo w these steps: Step 1 Install the cov er . Place it into position, slide it forw ard, and then tighten the ca ptiv e screw (l abeled 1 in Figure 2 ).
11 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Obtaining Technical Assista nce If you prefer to see advisories an d notices as they are updated in real time, you can acces s a Product Security Incident Response T eam Really Simple Syndication (PSIR T RSS) feed from this URL: http://www .
12 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Obtaining Technica l Assistance Access to all tools on the Ci sco T echnical Support & Documentat ion website requires a Ci sco.
13 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Obtaining Technical Assista nce Definitions of Service Request Severity T o ensure that all s ervice reque sts are rep orted in a standard format, Cisco has established se verity definitions.
14 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Obtaining Technica l Assistance This document is to be used in co njunction with th e documents listed i n the “Related Documentation” section. © 2006 Cisc o Systems, Inc.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Cisco Systems Engine 611 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Cisco Systems Engine 611 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Cisco Systems Engine 611, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Cisco Systems Engine 611 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Cisco Systems Engine 611, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Cisco Systems Engine 611.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Cisco Systems Engine 611. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Cisco Systems Engine 611 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.