Manuel d'utilisation / d'entretien du produit 3.1(6) du fabricant Cisco Systems
Aller à la page of 17
Cisco Unity 3.1(6) Installation Guide: Installing a Windows 2000 Server for Component System Document ID: 44332 Introduction Prerequisites Requirements Components Used Conventions Task 1: Start the Wi.
and hardware components must be installed by the installer of the Cisco Unity system. The Cisco Unity software package is purchased from Cisco or from a Cisco reseller.
Requirements Before you attempt this configuration, ensure that you meet these requirements: Windows 2000 Server Administration. • IP Addressing and related TCP/IP configuration options such as DNS, gateways, and so forth. • Components Used The information in this document is based on these software and hardware versions: Cisco Unity 3.
When the text "Setup will load support..." appears, press Enter . Note: If you see a message that indicates the installation cannot continue because a hard disk could not be detected, it is possible that you have not used the correct third party Windows 2000 Server driver.
Caution: If you elect to install an option that is listed as [No] below and it causes a conflict with Cisco Unity, you need to unconfigure it. It might not be supported on a server that runs Cisco Unity.
If the server that you are configuring is going to run Active Directory, you must enable File and Print Sharing For Microsoft Networks . This is required because Active Directory uses Networking in order to share the Active Directory files.
Select the Add/Remove Windows Components option. A menu screen similar to this image appears. 3. Select the Configure Message Queueing Services (Configure) option. Follow the prompts in order to complete the installation of Message Queueing Services. There are no user configurable options for this task.
Select Finish when the installation is completed. Close all of the Windows that are currently open. 5. Log off the current session and log back on again. The Windows 2000 Configure Your Server menu screen similar to this image appears. 6. Select the I will configure this server later option and select Next .
Un−select the Show this screen at startup option. Then close this window. 8. Task 4: Install Additional Windows 2000 Languages (Optional) If you want to view the Windows user interface in languages other than English, install the applicable languages.
Pack 2. Caution: When you install Internet Explorer, the file WScript.exe is installed automatically. Do not remove WScript.exe, or the Cisco Unity Setup program fails. Insert the Internet Explorer 5.5 CD that came with your Cisco Unity CD set in the CD−ROM drive.
Task 9: Change Windows Explorer Settings (Optional) This procedure ensures that all system files and folders are visible in Windows Explorer. This facilitates troubleshooting system problems in the future. From the Windows desktop, double−click My Computer .
tracert command instead. c:>tracert ip_address You should see a response something like this: Tracing route to [x.x.x.x] over a maximum of 30 hops: 1 <10ms <10ms <10ms [y.y.y.y] Where y.y.y.y is the IP address of the first gateway between your server and the IP address that you used.
Browse to the Bootdisk directory. 3. Double−click Makebt32.exe . 4. Follow the on−screen prompts. 5. Go to step 1 in Task 1. 6. Appendix B: Configure the Most Common TCP/IP Parameters Complete this procedure in order to configure the most common TCP/IP parameters.
A menu window similar to this image appears. Configure the IP options as appropriate. If you will be running Active Directory and DNS on this server, it should have itself as the first DNS Server. Select the Advanced option. A menu window similar to this image appears.
Click the DNS tab. A menu window similar to this image appears. 4..
These settings are correct for most systems. Consult your Windows 2000 Server documentation if you need more information on the configuration of TCP/IP options. Appendix C: Change the Name of the Computer Name (Optional) If you plan to change the name of your computer, do it as soon as possible.
NetPro Discussion Forums − Featured Conversations Networking Professionals Connection is a forum for networking professionals to share questions, suggestions, and information about networking solutions, products, and technologies. The featured links are some of the most recent conversations available in this technology.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Cisco Systems 3.1(6) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Cisco Systems 3.1(6) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Cisco Systems 3.1(6), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Cisco Systems 3.1(6) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Cisco Systems 3.1(6), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Cisco Systems 3.1(6).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Cisco Systems 3.1(6). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Cisco Systems 3.1(6) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
