Manuel d'utilisation / d'entretien du produit 5 du fabricant Cannon
Aller à la page of 28
OWNER’S MANU AL NOTE: Do not return your CANNON® Do wnrigger to your retailer. Your retailer is not authorized to repair or replace t his unit. You may obtain service b y: • calling CANNON® at 1.
2 Parts Description 1. Reel This is used to spool the cable, available in length s ranging from 1 50 to 400 feet. 2. Boom This is used to extend the weight out from the body of the downrigger and has a pulley fixed to its end. Boom lengths range from 24 to 53 inches.
3 Downrigger Mounting on Boats A downrigger should be mounted where ever it is easy to operate and observe. You want to be able to see your fishing rod and to react quickly. So, choosing a good spot to mount your downrigger on your boat is 99% of the job.
4 Side Rail Mounting Side/Rail mounts can be mounted to a welded T-section. It can also be used at the two rail section butt joint. In both installations it is recommended to use a non-slip material, such as rubber or a thin wood sheet, between metal surfaces.
5 MOUNTING & SETUP Outboard Fa cing Stern Facing Rear or Stern Note Locking Slots in Base Side or Gunwale Decks up to 7/16" Thick Base Wellnuts Decks Thicker Than 7/16" Washer, Lock Wash.
6 Decks thinner than 1/4" Use a Cannon Deck Plate to prevent deflection and add stability to decks thinner than 1/4". Use the deck plate as a template to mark the hole locations. If access to the underside of the deck is not available, the deck plate can be mounted using screws and wellnuts.
7 Clamps Standard 24" Boom #8 x 5/8" Screw (1) #4 x 1/2" Screws (2) The 3/4"-Long Phillips Screw Must Engage Hole in Boom Setting Up Y our Downrigger Attaching the Boom Telescopic .
8 Attaching the crank handle Thrust Bearing Spring Races Crank Handle Att aching the Crank Handle Assembly Make sure the thrust bearing is sandwiched between its two races. The thrust bearing spring should be oriented where the narrow end is toward the bearing.
9 T erminating the Downrigger Cable Cannon Uni-Release The Cannon Uni-Release attaches directly to the downrigger weight. Attach fishing line to the clip at the end of the release, and then click through a series of increasing tension settings.
10 CAUTION: This rod holder is intended for use of up to 30 lb. test line only, and is not recommended for use with any tackle IGFA rated higher than 30 lb. A safety strap (not included) is recommended for all applications. The rod holder assembly is not warranted when used with tackle above 30 lbs.
11 Operating Y our Downrigger After mounting the Cannon downrigger to your boat, release some line from your rod and reel so that the lure is anywhere from 5 to 100 feet behind the boat. This is called drop back. Attach the fishing line firmly into the line release.
12 Blowback Blowback Simply stated, blowback is what happens to the downrigger weight when you pull it through the water behind your boat. As your speed increases, so does the horizontal distance between the weight and your downrigger. The faster you go, the farther the weight is behind you.
13 Adjusting the Depth Meter The Cannon Depth Meter provides non-slip accuracy, plus easy resetting. To reset, just slide the meter away from the reel until the gears are disengaged. Spin meter gear to change setting. NOTE: Actual fishing depth may vary from depth shown on meter due to trolling speed and weight of cannon ball.
14 TROLLING TIPS T en Good T r olling Tip s 1) Test your lures over the boat side before sending them down and back. Do this to make sure the lure wiggles and wobbles properly without going belly up or wandering off. Some lures can be adjusted, fine tuned actually, to impart maximum action.
15 CANNON® LIMITED W ARRANTY Johnson Outdoors Inc. warrants to the original purchaser that if the accompanying product (see ex clusions below) proves to be defective in material or workmans hip within the following warranty periods, Johnson Outdoors Inc.
16 For a current list of aut horized Cannon Service Center s, including those ou tside of the US and Canada, please see our web page at www.cannondow nriggers.com . All CANNON Downriggers are covered by US Pat.D-269, 9 92. Copyri ght 2006 Johnson Outdoors, In c.
TM UNI-TROLL 10 1901100 Form No. 3394905 Rev 12/06.
1 3330002 FRAME - UNI-TROLL 29 3321001 COVER - CLUTCH, ROUND (LEXAN) 57 2371712 WASHER - 9/32" FLAT [4.EA] 2 3327004 DECAL - NOSE, UNI-TROLL 30 9250003 PIN - DOWEL 3/16" x 7/8" - RATCHE.
TM UNI-TROLL 10 METRIC 1901101 Form No. 3394913 Rev 12/06.
1 3330002 FRAME - UNI-TROLL 29 0902000 CRANK HANDLE - UNI-TROLL 57 2263102 NUT - HEX 1/4"-20 [4.EA] 2 3327004 DECAL - NOSE, UNI-TROLL 30 3321001 COVER - CLUTCH, ROUND (LEXAN) 58 2371712 WASHER - 9/32" FLAT [4.
TM UNI-TROLL 10 TS 1901110 Form No. 3394914 Rev 12/06.
1 3392506 FRAME - UNI-TROLL, WHITE 29 3390202 COVER - CLUTCH, ROUND, WHITE (LEXAN) 57 2371712 WASHER - 9/32" FLAT [4.EA] 2 3327004 DECAL - NOSE, UNI-TROLL 30 9250003 PIN - DOWEL 3/16" x 7/8&.
TM UNI-TROLL 10 TS/E 1901111 Form No. 3394919 Rev 12/06.
1 3392506 FRAME - UNI-TROLL, WHITE 29 0902000 CRANK HANDLE - UNI-TROLL 57 2263102 NUT - HEX 1/4"-20 [4.EA] 2 3327004 DECAL - NOSE, UNI-TROLL 30 3390202 COVER - CLUTCH, ROUND, WHITE (LEXAN) 58 2371712 WASHER - 9/32" FLAT [4.
TM UNI-TROLL 5 1901105 Form No. 3394915 Rev 12/06.
1 3330002 FRAME - UNI-TROLL 23 0467694 BRAKE PLATE - RATCHET 45 2277002 >UNIVERSAL LINE RELEASE 2 3327004 DECAL - NOSE, UNI-TROLL 24 1000904 SHAFT - RATCHET - UNI-TROLL 46 3992300 SWIVEL HEAD ASSEMBLY 3 9040040 HOOK - 1/4" - 20 ROLLED 25 9010310 WASHER - THRUST [2.
TM UNI-TROLL 5 METRIC 1901106 Form No. 3394916 Rev 12/16.
1 3330002 FRAME - UNI-TROLL 23 1264670 CLUTCH PAD 45 9430160 >WASHER - STAR 5/16" 2 3327004 DECAL - NOSE, UNI-TROLL 24 0467694 BRAKE PLATE - RATCHET 46 2277002 >UNIVERSAL LINE RELEASE 3 904.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Cannon 5 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Cannon 5 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Cannon 5, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Cannon 5 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Cannon 5, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Cannon 5.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Cannon 5. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Cannon 5 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
