Manuel d'utilisation / d'entretien du produit SSIM-H2-02 du fabricant Cabletron Systems
Aller à la page of 72
SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and User Guide.
i Notice Notice Cabletron Systems res erves the right to mak e changes in specif ications an d other information contained in this document with out prior notice. The reader sho uld in all cases consult Cabletron Sys tems to d etermine whether any s uch chan ges ha v e been made.
ii Notice FCC Notice This device complies with Part 15 of the F CC rules. Operation i s subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept an y interference r eceiv ed, including interference that may cau s e undesired operation.
iii Notice Dec laration of Conf ormity Addend um Application of Council Directi ve(s): 89/336 /EEC 73/23/ EEC Manufacturer’ s Name: Cabletron Syst ems, In c. Manufact urer ’ s Address: 35 Industri al Way PO Box 50 05 Rochester, NH 038 67 European Representati ve Name: Mr.
iv Notice.
v SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide T abl e of Contents 1. Introduction 1 MIB Suppo rt . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Installat ion 5 Package Con tents .
vi SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Frame Co nversion Confi guration . . . . . . . . . . . . . . . . . 32 TCP/IP Con version Statu s . . . . . . . . . . . . . . . . . . . 32 TCP/IP Con version Parame ters Change .
vii SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide List of Figu res Figure 1. SSIM-H2- 02 Switch S martStack Inte rface Modul e . . . . . 1 Figure 2. Removi ng the Expan sion Slot Co ver . . . .
viii SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide List of T ab les Table 1. Features a nd Benefits . . . . . . . . . . . . . . . . . . . . 2 Table 2. LEDs at the Left on the Front Pane l . . .
1 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Introduction 1. Intr oduct ion The Cabletron Systems SmartStack SSIM-H2 -02 2-port Trans lati.
2 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Introduction The modul e support s translat ional swi tching for all ke y n etwork protocol s (such as IP , IPX, SN A, NetBios) and gen eric conv ersion: F eature Description SR T and SRB Support for SR T and SRB br idging.
3 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Introduction SNMP SNMP is sup port ed via the h ost processor (the processor on the SmartS tack STS16-20RM). This makes it possible to configure the device in a standards-bas ed way and as an inte grated part of the LAN switch.
4 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Introduction MIB Suppor t • RFC 12 13: MIB I I • RFC 1493: Bridge MIB • RFC 1525: SR Br.
5 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Installation 2. Installation This chapter describes h ow to install, connect, and start using the SSIM- H2-02.
6 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Installation Insta llation Procedure The SSIM-H2-02 is packaged with the software for both the module itself and the SmartStack STS16-20RM Token Ring Switch.
7 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Installation Har dware Inst allation ➽ Wa r n i n g : Expans ion modu les are no t hot-sw appable. If you i nstall or r emove expa nsion modu les while the po wer to the switc h is on, d amage may o ccur to the switch and to the module.
8 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Installation 4. Carefully insert the mod u le into the rails on each side o f the expa nsion slot, sliding it b ack until the connecto r on the module is seated into the co nnector at the back of the slot.
9 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Installation The console will display the d o wnload activity while the software is transferred over the network b y counting received blo cks .
10 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Installation Cabling The modul e uses st andard or cr ossed-over UTP-5 co pper cables.
11 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Installation P ower - On S el f T es t When you st art the switch, it will run a power-on self-test to ensure that all the devices are w orking correctly.
12 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Installation Configuration The SSIM-H2-02 can b e configured in t wo ways: • From the switch console, directly with a VT100 terminal emulator on the RS- 232 po rt or via T eln et.
13 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration 3. Configuration This chapter explains h o w to view and edit the configuration of the SSIM-H2-02 using a VT100 ter minal emulator attached directly to the Smar t Stack STS16-20 RM Token Ring s wi tch.
14 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n Introduction Each SSIM-H2-02 has two 100 Mbps Fas t Ethernet ports. In the console configur ation, port n umbers are u sed to refer t o ports, wi th ordinar y Token Ring ports numbered 1 to 20.
15 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration TS Vir tual P orts and VLAN T agging Unlike ord inary Token Ri ng port s, Tran.
16 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n Bridging Modes Sour ce Routed Switching (SRS) Operation Mode SRS is th e default mod e of oper ation. This m ode is also res tored after NV RAM reset of the SmartStack STS16-20RM switch.
17 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration Source Routed Bridgi n g (SRB) Mode ➽ Note: SR T is the sug gested mode o f operation. If multiple CRFs are used on a switch, all tran slatio nal links to the same Ethernet cloud should b e grouped into o ne CRF.
18 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n Redundant Connection s to Fast Ethernet Netw or k A connection to the Eth ernet cloud can be made using several translation al links from multiple swi tches.
19 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration In a pure To ken Ri ng ne twor k, an A ll Rou tes Ex plor er (AR E) fra me gen erat ed fro m Station A traverses all r in gs only one time based on a Routing Inform ation Field (RIF) expanded by each sour ce-routed bridg e.
20 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n This loop can be resolved b y maki ng sure that only one translational lin k is in the forwarding s tate or by using the same LAN s egment number f or all translational links.
21 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration For each CRF of translation al links connected to t he same Ether net cloud, a connection attribute can b e assigned: — Primary connection – fo r a main conne ction to the Ethernet cloud (def ault v alue for each CRF).
22 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n Figure 10 illustrates a network with two physically disjoint Ethernet cloud s.
23 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration T echnical Bac kg r ound For each CRF with a transl ational link, spannin g tree should be en abled. For SRT CRF, the default STP algor ithm is IEEE 802.
24 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n Figure 11. S TP Cost Modification In Figure 1 1, TR Switch 2 and Ethernet Switch 2 know that the cost of the Secondary link is 20,000 higher than the cost of t he primary link seen by T R Switch 1 and Ethern et Switch 1.
25 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration Gene ra l G uid elines This section describ es g uidelines for work within the conso le menu s. • T o select a menu item, use the arrow ke ys to highlight it, then p ress ENTER .
26 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n Navigating Within the Menus Use the arrow keys (cursor keys) to highligh t a selection.
27 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration Configu ration O ver view Execute the following general step s to configure a SSIM-H2-02: • Determine w hich V LANs the TS po rts should conn ect.
28 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n VLAN Configuration For general informatio n about the configuration of VLANs, refer to the SmartStack STS16-2 0RM/STS16-20FRM Token Ring Swi tch Ins tallatio n and U ser Guide .
29 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration Status Display onl y. Shows the current st atus of the port.
30 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n Status Disp lay onl y. Show s the cu rrent s tatus of the vi r tual po rt.
31 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration VL AN T agging M od e Sets the VLAN tagging mode of the virtual port; possible valu es ar e Tagged and Untagged . As explained p reviously, only o ne virtual port on each TS port can be untagged.
32 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n Explorer RIF Aging Time On output, the Translational Switch UEM quickly deletes ad dresses known only from forwarded explorer frames .
33 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration IP: Ethernet For mat Sets the format of IP f rames on Ethernet. Default: Ethernet II Sour c e Routing Enables or disables Source Routing in I P frames transmitt ed to To ken Ring.
34 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n Explorer Frames T ype Sets the type of explorer that should be used for ARP/RARP traf fic. From the set of IP pro tocols e xplorer frame t ype can be chos en only for ARP/ RARP frames .
35 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration Novell Con version P aramet ers Chang e To change Novel l conversion parameters select NOVELL conversion parameters change on the Fra me Conv e r si o n Confi gu ration me nu of the TS port.
36 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n Sour ce Routing Enables or disables Sou rce Routing in Novell frames transm itted to Token Ring. Default: noSR Explorer Frames T ype Sets the type of exp lorer for IPX traffic.
37 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration Dis abled . If the state is set to Disabled , NetBios traffic will be dropped. Default: Enabled NetBios: T oken Ring Format Sets the format of NetBios frames o n Token Ring.
38 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n Explorer Frames T ype Sets the type of exp lorer that shou ld be used fo r NetBios traffic. Default: STE TR Functional Address The TR Functional Address is entered in the MAC address format.
39 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration SNA: Ethernet Format Sets the format of SNA frames on Ethernet. Default: 802.3 Sour c e Routing Enables or disables Sour ce Routi ng in SNA f rames tran smitted to Token Ring.
40 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n Explorer Frames T ype Sets the type of exp lorer that shou ld be used fo r SNA traffic. Default: ARE Other Frames w/SNAP Con ver sion Status Display only.
41 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration Other Frames w/SNAP: Ethe rnet Format Sets the format of Other Frames w/SNAP frames on Ethernet.
42 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n Conversion. Po ssible values are Enabled and Dis abled .
43 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Configuration Sour c e Routing Enables or disables So urce Routing in Other Frames w/o SNAP frames transmitted to To ken Ring .
44 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Co nf iguratio n.
45 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Statistics 4. Statistics A wide range of statistics is available for the SmartStack Token-Ring Switch.
46 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Statistics Statist ics Men u When Statistics is selected from the m a in men u, the follo wi.
47 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Statistics Po r t S t a t u s Besides the or dinary Token-Ri ng ports, th e table contains an en t ry for each TS virtual port , along with its current status.
48 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Statistics Po r t S t a t i s t i c s When Po rt Statistics is selected and the port num ber of a TS port is entered, the following opti ons are listed: — G eneral Statistics — 80 2.
49 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Statistics SRF Frames Number of Specifically Routed Fram es . STE Fra mes Number of Spanning Tree Explorers. ARE Fr ames Number of All-Routes Expl orers.
50 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Statistics T able Filter ed by Address Filter The frame by discard ed because of a MAC address filter. T able Filtered by DSAP Filter The frame by discard ed because of a protocol ( DS AP or pro tocol type) filter.
51 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Statistics • T ranslational Switch receiv ed frame with RIF but, for this pro tocol, the noSR flag is used d uring con versions.
52 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Statistics Err or Count er s Single Collisions Number of frames transmitted by this port after si ngle collision. Mult iple C o llisi o ns Number of frames transmitted by this port after mul tip le collision.
53 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Statistics Virtu al P or t Statistics When Virtual Port Statistics is selected from the Port Statistics menu for a TS port, coun ters for the virtual port are di splayed.
54 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Statistics NetBios Number of fram es dropped because NetBios translation is disabled or inbound frames are received from Ethern et in a format different than that specified in the TS configuration d ialog.
55 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Statistics Outbound (No T ranslation) TCP/IP Number of frames dropped b ecause TCP/IP translation is d isabled.
56 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Statistics Generic w/ o SNAP Number of frames dro pped because of trans lation errors for gen eric frames without SNAP. Fragmentation E rror (TCP/IP only.
57 SSIM-H2-02 Fast E thernet - T ranslational Switch SmartStack Interface Module I nstallation and User Guide Getting in T ouch with T e chnical Support 5.
58 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Getting in T ouch with T e c hnical Support.
59 SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide Abbreviations Appendix A. Abbre viations AC Access Control ARE All-R outes E xpl or er ATM A.
60 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Abbre viations RIF Route Information Field RX Receive Data SA Source Address SAP Service Acc.
index-1 Index SSIM-H2-02 Fast Ethernet - T ranslational Switch SmartStack Interface Module Installation and User Guide A abbrev iations 59 B Bridging Mod es 16 Source Ro ut ed B ridging (SRB) 17 Sourc.
index-2 SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and Us er Guide Inde x V VLAN configur ation 28 BRF c onfigu rati on 28 local VLA N po rt configur atio.
* 710001816*.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Cabletron Systems SSIM-H2-02 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Cabletron Systems SSIM-H2-02 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Cabletron Systems SSIM-H2-02, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Cabletron Systems SSIM-H2-02 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Cabletron Systems SSIM-H2-02, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Cabletron Systems SSIM-H2-02.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Cabletron Systems SSIM-H2-02. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Cabletron Systems SSIM-H2-02 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
