Manuel d'utilisation / d'entretien du produit 2895E du fabricant Buhler
Aller à la page of 46
.
PRINTED IN CANADA WARRANTY REGISTRATION AND POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications.
bühler Allied Front-End Loader - 1 - P4493 2895E OPERATOR’S AND PARTS MANUAL Table of Contents D e s c r i p t i o n P a g e Registration and Policy Loader Specifications .............................................................................
bühler Allied Front-End Loader - 2 - P4493 LOADER SPECIFICATIONS Illustration (TSL shown).
bühler Allied Front-End Loader - 3 - P4493 Specification Chart Item Description 2895E REG 2895E TSL 2895E S REG 2895E S TSL A Maximum lift height to pivot pin [in/cm] 181/460 181/460 169/429 169/429 .
bühler Allied Front-End Loader - 4 - P4493 INTRODUCTION This manual has been provided as information regarding the specifications, safe operation and maintenance of your agricultural front-end loader. Read and understand this manual and the tractor manual prior to operating to obtain the best use of operating your loader.
bühler Allied Front-End Loader - 5 - P4493 Serial Decal Location: The serial decal is located on the inside left arm of the loader joint plate. Please record the serial number in the space provided for future reference.
bühler Allied Front-End Loader - 6 - P4493 SAFETY Read and understand all the safety messages listed in this manual. For your safety and the safety of others near the machine, learn how to control and operate the loader properly. It is your responsibility to inform subsequent operators and owners of these precautions.
bühler Allied Front-End Loader - 7 - P4493 Safety Decals: Safety Decal Location illustrates the approximate location and detail of safety decals. To install safety decals ensure the installation area is clean and dry. Decide on the exact position before you remove the backing paper.
bühler Allied Front-End Loader - 8 - P4493 Safety Decal Location.
bühler Allied Front-End Loader - 9 - P4493 The following pictorials indicate important precautions to be used during the operation of the loader. WARNING WARNING WARNING FA LLING HAZARD To pr event seri ous injur y or deat h: Do not lift, carry or al low anyone to ride on or work from any portion of loader.
bühler Allied Front-End Loader - 10 - P4493 PRE – OPERATION WARNING The tractor must be equipped with an approved Roll over Protection Structure (ROPS) and safety belts to help prevent personal injury or death caused by tractor roll over. CAUTION Maximum rated loader capacity may exceed tractor rating.
bühler Allied Front-End Loader - 11 - P4493 OPERATION General Operating Notes: The following section provides general information that can be applied towards your specific application. Ensure that you’ve read and understood this manual and your Tractor Manual .
bühler Allied Front-End Loader - 12 - P4493 All Buhler - Allied hydr aulic valves are self-centering and return to neutral from all positions except float. The float or detent spool is only to be used on the boom circuit. This position allows the oil to freely flow through the valve so the lift cylinders can extend or retract.
bühler Allied Front-End Loader - 13 - P4493 Minimize turning angle and length of run between pile and trailer to increase loading efficiency. Also, place load evenly or centered in the attachment. WARNING Carry the load no higher than necessary to clear the terrain.
bühler Allied Front-End Loader - 14 - P4493 For back grading, either load the bucket and position the heel on the ground or position the bucket at 40 q or less below level as shown.
bühler Allied Front-End Loader - 15 - P4493 Handling bales and pallets: For safe handling of bales and pallets please follow procedures below: WARNING Do not operate A – Frame for bales without the stabilizers.
bühler Allied Front-End Loader - 16 - P4493 When loading bales onto a trailer, park trailer in close proximity to minimize turning angle and length of travel to increase loading efficiency. As you lift the bale using the regular loader, it is recommended to feather the valve to allow bucket cylinders to extend to keep bale at about a 20 q angle.
bühler Allied Front-End Loader - 17 - P4493 Grapple: The grapple is designed to safely prevent loads (bales, silage) from falling out of the bucket. (Refer to pictorial below for options listed) WARNING Travel at low speeds. Carry loads as low as possible.
bühler Allied Front-End Loader - 18 - P4493 INSTALLING / REMOVING LOADER Installing: CAUTION Prior to initial mounting, cycle loader cylinders to displace air. This ensures the loader will remain in the storage position and operate consistently. 1. Position the tractor centrally and parallel to the loader uprights.
bühler Allied Front-End Loader - 19 - P4493 5. With the tractor in neutral, continue to retract the lift cylinders and extend the bucket cylinders to rotate the upright back against the lock pin stops. Shut the tractor off and set park brake. 6. Install both upright attachment pins and secure with hairpin clip.
bühler Allied Front-End Loader - 20 - P4493 2. Lower attachment level to the ground while engaging float position. Ensure attachment rests firmly on ground with minimal downward pressure. If required extend bucket cylinders to rotate upright rearward.
bühler Allied Front-End Loader - 21 - P4493 INSTALLING / REMOVING LOADER ATTACHMENTS Installing: 1. Position tractor centrally within the bucket hooks. Dump Quick-tach slightly from vertical position. Slowly drive the tractor forward until the Quick-tach contacts the bucket.
bühler Allied Front-End Loader - 22 - P4493 LUBRICATION Lubricate loader bushings and pivots every eight hours of average operation with high-grade grease. For grease fitting locations see illustration below. Select grease based on the expected outside temperature range.
bühler Allied Front-End Loader - 23 - P4493 MAINTENANCE General Inspection: CAUTION Lower attachment and loader to ground, place all controls in neutral, stop engine, set parking brake and remove ignition key before inspecting, servicing, adjusting or repairing loader.
bühler Allied Front-End Loader - 24 - P4493 Mounting Kit: After the initial 2 weeks or 40 hours of loader operation, and 6-month intervals thereafter re-torque all mounting kit bolts. (See below for proper bolt torques) Bolt Torque Chart: Standard Metri c ft-lbs NM ft-lbs NM ft-l bs NM ft-lbs NM ft-lbs NM ft-lbs NM ft-lbs NM 0.
bühler Allied Front-End Loader - 25 - P4493 Hydraulics: WARNING Escaping fluid under pressure can have sufficient force to penetrate the skin, causing serious personal injury. Before repairing, adjusting, or disconnecting lines, be sure to relieve all pressure.
bühler Allied Front-End Loader - 26 - P4493 A yearly inspection of the valve is recommended. However the maintenance intervals on the valve depends on the surrounding environment or if valve spools become stiff.
bühler Allied Front-End Loader - 27 - P4493 On valves fitted with joystick cables loosen off jam nut and cable sleeves to gain access to the valve spool. Clean all debris and any existing corrosion. Spray areas with a light corrosion resistant lubricant.
bühler Allied Front-End Loader - 28 - P4493 TSL GENERAL NOTE AND INSTRUCTIONS 1. The true self leveling system (TSL) utilizes mechanical linkages to maintain bucket level while raising and lowering.
bühler Allied Front-End Loader - 29 - P4493 TROUBLE SHOOTING Possible Cause Quick couplers leaking Hydraulic oil too heavy. Oil filter plugged. Hydraulic pump worn. Oil line restricted or leaking. Control valve does not shift properly. Air in hydraulic system.
bühler Allied Front-End Loader - 30 - P4493 Trouble Shooting Continued Problem Insufficient lift capacity. Slow leak down. Excessive wear on bottom of bucket and wear pads. Hydraulic cylinders inoperative. Pump operating continually on closed center tractor hydraulics system.
bühler Allied Front-End Loader P4493 - 31 - 2895E & 2895E S PARTS APPENDIX Description Page 2895E & 2895E S Main Frame Asse mbly .............................................................................. 32 Hydraulic Plumbing ............
bühler Allied Front-End Loader P4493 - 32 - 2895E & 2895E S Main Frame Assembly 5.
bühler Allied Front-End Loader P4493 - 33 - 2895E & 2895E S Main Frame Assembly Item Part No. Description 2895E 2895E S 1 24966 2895 Main Frame Weldme nt (113579, 113633 includ ed) 1 - 1 24944 2895 S Main Frame Weldment (bushings in cluded) - 1 2 25388 2895 Euro Quick Attach Weldment 1 1 3 Ref.
bühler Allied Front-End Loader P4493 - 34 - 2895E & 2895E S Hydraulic Plumbing Assembly.
bühler Allied Front-End Loader P4493 - 35 - 2895E & 2895E S Hydraulic Plumbing Assembly Item Part No. Description 2895E 2895E S 1 Ref. Bucket Cylinder (See cylinder assembly for brea kdown) 2 2 2 Ref.
bühler Allied Front-End Loader P4493 - 36 - 2895E TSL & 2895E S TSL Main Frame Assembly 45 45.
bühler Allied Front-End Loader P4493 - 37 - 895E TSL & 2895E S TSL Main Frame Assembly Item Part No. Description 2895E TSL 2895E S TSL 1 24967 2895 TSL Main Frame Weldment (bushings incl.) 1 - 1 24945 2895 S TSL Main Frame Weldment(bushings incl.
bühler Allied Front-End Loader P4493 - 38 - 2895E TSL & 2895E S TSL Hydraulic Plumbing Assembly 4 3 15 13 7 B B A 12 VIEW A- A 3 4 9 10 11 14 6 17 13 16 5 2.
bühler Allied Front-End Loader P4493 - 39 - 2895E TSL & 2895E S TSL Hydraulic Plumbing Assembly Item Part No. Description 2895E 2895E S 1 Ref. Bucket Cylinder (See cylinder assembly for brea kdown) 2 2 2 Ref.
bühler Allied Front-End Loader P4493 - 40 - Possible Attachment Interference (2895E TSL & 2895E S TSL) Regular loader linkage setup allows for maximum rollback. TSL loader linkage setup provides reduced rollback. When fully rolled back, large attachments (such as the C2000 Grapple) may contact the 2895E TSL or the 2895E S TSL pivot plate.
bühler Allied Front-End Loader P4493 - 41 - 2895E Cylinder Assembly NOTES: 1. Bucket cylinder shown 2. All cylinder seals are contained in correspon ding seal kit. 3. Refer to page 44 for prevailing torque for locknut s. CAUTION Maximum pressure – 3000 psi Bucket Cylinders Lift Cylinders Regular & TSL Regular TSL Regular Short Diameter 3.
bühler Allied Front-End Loader P4493 - 42 - Hydraulic Fitting Torques: (ft-lbs) (NM) (ft-lbs) (NM) -04 7/16-20 14-16 20-22 10-11 13-15 -05 1/2-20 18-20 24-27 13-15 18-20 -06 9/16-18 24-26 33-35 17-19.
.
Buhler Manufacturing “ a partnership” Customer Support: 1-888-524-1003 1260 Clarence Ave. Box 7300 Winnipeg, MB. R3C 4E8 Ph.: (204) 661-8711 Fax: (204) 654-2503 www.buhler.com Printed in Canada Allied Division 1201 Regent Ave. W. Box 1003 Winnipeg, MB R2C 3B2 Ph.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Buhler 2895E c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Buhler 2895E - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Buhler 2895E, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Buhler 2895E va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Buhler 2895E, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Buhler 2895E.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Buhler 2895E. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Buhler 2895E ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
