Manuel d'utilisation / d'entretien du produit 12180 du fabricant Bolens
Aller à la page of 28
Model 12180 Owner’ s Manual BRONCO TM 5 HP Model T iller • Safety • Assembly • Controls • Operation • Maintenance B R O N C O GARDEN WAY INCORPORATED.
2 T able of Contents SECTION 1: SAFETY ........................................... 3 Safety Decals .................................................................... 5 SECTION 2: ASSEMBLY ....................................... 6 Attach Handlebar ..
3 T raining 1. Carefully read this Owner ’ s Manual, the separate Engine Owner ’ s Manual, and any other literature you may receive. Be thoroughly familiar with the controls and the proper use of the tiller and its engine. Know how to stop the unit and disengage the controls quickly.
7. Take all possible precautions when leaving the machine unattended. Stop the engine. Disconnect spark plug wire and move it away from the spark plug. Be sure both wheels are in the Wheel Drive position. 8. Before cleaning, repairing, or inspect- ing, stop the engine and make certain all moving parts have stopped.
Section 1: Safety 5 Decals For your safety and the safety of others, various safety and operational decals are located on your unit (see Figure 1 below). Keep the decals clean and legible at all times. Contact your local service dealer or the factory for replacements if any decals are damaged or missing.
6 WARNING T o prevent personal injur y or property damage, do not start the engine until all assembly steps are complete and you have read and understand the safety and operating instruc- tions in this manual. Introduction Carefully follow these assembly steps to correctly prepare your tiller for use.
7 Section 2: Assembly STEP 2: Attach Handlebar 1. Attach the two legs of the handlebar support (A, Fig. 2-2) loosely to the inner sides of the tiller frame using two 3/8"-16 x 3/4" hex hd. screws (B), 3/8" flat washers (C) and 3/8"-16 hex locknuts (D).
8 Section 2: Assembly STEP 4: Install Forward Clutch Cable 1. Place the forward clutch cable bracket (P, Fig. 2-4) on the handlebar support (A). Attach the cable bracket using a 1/4"-20 x 1-1/4" hex hd. screw (R, Fig. 2-4) and 1/4"-20 hex locknut (S).
9 Section 2: Assembly Fig. 2-8: Install reverse cable bracket and reverse clutch cable. 3. Unwrap the reverse clutch cable (the cable with a knob and a large hex nut attached to it) from around its shipping position and route the cable (CC, Fig. 2-8 and Fig.
Wheel Drive Pins Each wheel is equipped with a Wheel Drive Pin (A, Figures 3-2 and 3-3) that secures the wheel to the wheel shaft (B). The wheels can be positioned in either a WHEEL DRIVE or a FREEWHEEL mode.
11 Section 3: Features and Controls 4. FOR WHEEL DRIVE mode (Figure 3-2): Slide the wheel outward and align the holes in the wheel hub (D, Figure 3-2)) and the wheel shaft (B).
12 Section 3: Features and Controls Depth Regulator Lever This lever (G, Figure 3-5) controls the tilling depth of the tines. Pull the lever straight back and slide it up or down to engage the notched height settings. The highest notch (lever all the way down) raises the tines approximately 1-1/2" off the ground.
13 Figure 4-1 Section 4 Operation WARNING Before operating your machine, carefully read and understand all safety (Section 1), controls (Section 3) and operating instructions (Section 4) in this Manual, in the separate Engine Owner ’ s Manual, and on the decals on the machine.
14 Starting the Engine The following steps describe how to start and stop the engine. Do not attempt to engage the tines or wheels until you have read all of the operating instruc- tions in this Section. Also review the safety rules in Section 1: “ Safety ” and the tiller and engine controls information in Section 3: “ Features and Controls.
15 Section 4: Operation 5. For reverse motion of the wheels and tines: (a) Look behind and exercise caution when operating in reverse. Do not till while in reverse.
16 Section 4: Operation T illing T ips & T echniques Let the tiller do the work • While tilling, relax and let the wheels pull the tiller along while the tines do the digging. Walk on the side that is not yet finished (to avoid making foot- prints in the freshly tilled soil) and lightly, but securely grip the handlebar with just one hand.
17 Section 4: Operation T illing T ips & T echniques Clearing the tines The tines have a self-clearing action which eliminates most tangling of debris in the tines. However, occasionally dry grass, stringy stalks or tough vines may become tangled.
18 Section 4: Operation POWER COMPOSTING Power composting simply means tilling under and burying in the soil all manner of organic matter such as crop residues, leaves, grass clippings and cover crops. This material will decompose during the non-growing season and add important natural nutrients to the soil.
19 Section 5 Maintenance REQUIRED MAINTENANCE SCHEDULE Before Every Every As PROCEDURE Each 10 30 Noted Use Hours Hours Check engine oil level • And every 5 operating hours Clean engine • ▲ Chec.
20 Section 5: Maintenance TILLER LUBRICA TION Proper lubrication of the tiller is an essential part of your maintenance program. After every 10 operating hours, oil or grease the lubrication points shown in Figure 5-1 and described below.
Section 5: Maintenance B. To Drain the Transmission Gear Oil: The transmission gear oil does not need to be changed unless it has been contam- inated with dirt, sand or metal particles. 1. Drain gasoline from the fuel tank or run the engine until the fuel tank is empty.
CHECKING AND ADJUSTING FORWARD DRIVE BEL T TENSION Maintaining correct tension on the forward drive belt is important to good tilling performance and long belt life. A loose belt will slip on the engine and transmission pulleys and cause the tines and wheels to slow down – or stop com- pletely – even though the engine is running at full speed.
Section 5: Maintenance W ARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage.
24 Section 5: Maintenance W ARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage.
25 Section 5: Maintenance TROUBLESHOOTING Before performing any corrections, refer to the appropriate information in this Manual, or in the Engine Owner ’ s Manual, for the correct safety precautions and operating or maintenance procedures. Contact your local authorized Engine Service Dealer for engine service.
26 TILLER SPECIFICA TIONS/A TT ACHMENTS TILLER SPECIFICA TIONS TILLER HEIGHT (with Depth Regulator Lever in highest setting): Without Handlebars .................................................................................25-1/2" Handlebars in lowest setting.
27 CUSTOMER SERVICE INFORMA TION Owner Registration Card Please fill out and mail the enclosed owner registration card. The purpose of this card is to register each unit at the factory in order to keep the owner informed with informational bulletins and safety literature.
1905237 (1/99) Printed in U.S.A. © 1999 Garden Way Incorporated.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Bolens 12180 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Bolens 12180 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Bolens 12180, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Bolens 12180 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Bolens 12180, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Bolens 12180.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Bolens 12180. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Bolens 12180 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
