Manuel d'utilisation / d'entretien du produit 8742 du fabricant Bloomfield
Aller à la page of 22
PRINTED IN UNITED STATES OF A MERIC A p/n 76116 Rev. E ECN-12888 M606 05 0614 cps 606 OWNERS MANUAL for ICED TEA BREWING SYSTEM MOD EL S: 8742 8748 Includes: Installation Operation Use & Care Serv.
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged b y skilled personnel before le aving the factory. Upon acceptance of this shipm ent, the transportation company assumes full responsibility for its safe delivery.
MODEL DIMENSIONS VOLTS WAT TS AMP S 1ø POWER SUPPLY CORD 8742 3 Gallon Iced Tea Brew er 32-1/4" high 10-15/16" w ide 15-11/16" deep 120 1500 12.5 NEMA 5-15P 8748 5 Gallon Iced Tea Brew er 35-1/4" high 10-15/16" w ide 15-11/16" deep 120 1500 12.
FE AT U R E S AN D O P E R AT I N G CO N T R O L S 2 606 Owners Manu al for 8742-8 748 Tea Brewer 76116.
PRECAUTIONS A ND GENERAL INFORM A TION 3 WA RNI NG: Electric Shock Hazard All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock.
INSTALL ATION 4 RE A D THIS CAREFULL Y BEFORE ST A RTING THE INST A LLA TIO N Unpack the unit. Inspec t all components f or completeness and condition. Ensure that all packing materials have been removed from the unit. Verify that the Spray Head Gasket and Spray Disk are properly installed.
INSTALLATION (continued) 5 NOTE: This equipment must be installed to comply with applicable federal, state an d local plum bing codes an d ordinanc es. WARNING ELECTRIC SHOCK HAZARD: Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide suc h a ground .
OPERATION Fig. 3 Brewer Operation Diagram A. ST ART- UP For initial start-up, or if the br ewer has not been used for an extended period of t ime: ♦ Be sure spray disk and bre w gasket are properly installed in the brew head. ♦ Be sure the water supply is prope rly conne cted and the w ater supply valve is turned ON .
OPERATION (continued) WATER HEATER Water temperature is sensed by a thermobulb inserted in to the water tank. This te mpe rature signal is fed to the mechanical thermostat. The temperature setpoint is adjustable. Heating element is energized by the thermostat.
BREWING TEA 8 A. PREP A RATION Exam ine the tea brew cham ber to v erify that the short the wire rack is in place. Place one (1) genuine Bloomfield paper f ilter into the wire rack in the tea bre w chamber. Ad d an amo unt of fresh tea leave s to the bre w chamber appropriate to the bre w volume.
CLEANING I NSTRUCTIONS PROCEDURE: Clean Tea Brewer PRECAUTIONS: Disconnect brewer fro m electric power. Allow brewer to cool. FREQUENCY: Daily TOOLS: Mild Detergent, Clean So ft Cloth or Sponge Bristle Brush, Bottle B rush 1. Disconnect brewer from electric pow er.
TROUBLESHOOTING SUGGEST IONS SUGGESTED REMEDY Check po wer supply cord Check / reset circuit breaker Set for desired temperature Allow to cool hi-limit will self- reset Examin e wiring & connec to.
SERVICING IN STRUCTIONS CA UTI ON Electric Shock Hazard Opening access pane ls o n this brew ma y expose uninsul ated electrical co m ponents. Disconnect brewer from electrical power before removing any pan el. ACCESS PANELS TOP P ANE L: Remove top panel to ac cess hot water tank, thermostat, tim er, brew solenoid an d brew c ircuit tub ing.
SERVICING INST RUCTIONS (continued) 12 TEMPERATURE ADJUSTMENT Unplug power cord or turn circuit breaker OFF. Remove top panel. Pull vent tube o ut of tank lid and inse rt a thermometer of known accuracy in hole. Reconnect brewer to electrical powe r. Place empty cont aine r under bre w chamber.
SERVICING INSTRUCT IONS (continued) IMPORTANT: Water pressure must be betwe en 20 p.s.i and 90 p.s.i. flowing pressure . If water pressure exceeds t his value, or if water pressure varies greatly, a pressure regulator must be installed in the water supply line.
SERVICING IN STRUCTIONS (continued) REPLACE HEATING ELEMENT Remove tank cover assembly (see page 13). Remo ve two hex nuts hol ding elem ent to cover. Pull elem ent from mounting holes. Reassemble in reverse o r der. REPLACE SOLENOID Symptom: Automatic brew er will not flow water; or, autom atic brewer drips c ontinuous ly from brew hea d.
SERVICING INSTRUCT IONS (continued) 15 CA UTIO N - CHEMICA L BURN HA ZAR D Deliming chemicals are c austic. Wear appropriate protective gloves and goggles during this procedur e. Never siphon deliming chemicals or solutions by mout h. This operation shou ld only be performed by qua lified and ex- perienced service personnel.
8742 - 8748 EXPLODED VIEW & PARTS LIST 16 606 Owners Manu al for 8742-8 748 Tea Brewer 76116.
8742 - 8748 EXPLODED VIEW & P ARTS LIST (continued) 17 606 Owners Man ual for 8742-8 748 Tea Brewer 761 16.
8742 - 8748 SERVICE KITS 18 SOLENOID REPAIR KITS (SKINNER SOLENOID ONLY) 8541-120CS Coil Assem bly (item 45-1) 8541-120K Solenoid Repair Ki t (includes it ems 45 -2 Spring, 45-3 Plunger & x45-4 Se.
8742 - 8748 WIRING DIAGRAM 19 606 Owners Man ual for 8742-8 748 Tea Brewer 761 16.
PRINTED IN UNITED STATES OF A MERIC A Bl oo m f ie l d I ndu s t ri e s, Inc . Di vis io n of Ca rri er C om mer ci al Refri g erat io n In US and Canada T elephone: 775-698- 5700 Fax: 888-492- 2783 Fax: 800-356- 5142 () websi te: www . wells bloomfi eld.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Bloomfield 8742 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Bloomfield 8742 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Bloomfield 8742, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Bloomfield 8742 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Bloomfield 8742, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Bloomfield 8742.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Bloomfield 8742. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Bloomfield 8742 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
