Manuel d'utilisation / d'entretien du produit MDS932AE-FXS du fabricant Black Box
Aller à la page of 25
User Manual MDS932AE-10BT STANDALONE MDS932AE-FXO STANDALONE MDS932AE-FXS STANDALONE MDS933AE-10BT STANDALONE MDS932C-10BT RACK-CARD MDS933C-10BT RACK-CARD G.
.
User Manual VERSION CONTROL .......................................................................................................... 5 1 GENERAL INFORMATION........................................................................................ 6 ORDER INFORMATION .
User Manual 8.4 Line1 and Line2 Connector ............................................................................. 24 9 DESCRIPTION OF INTERFACE CABLES .............................................................. 25 9.1 Ethernet cable .........
User Manual VERSION CONTROL Version Date Major changes to previous version 1.0 31.12.2001 Initial version of the manual corresponding to version 1.2 of the device micro program 1.1 23.10.2003 New function description corresponding to software release V1.
User Manual 1 GENERAL INFORMA TION • High-speed symmetrical data transmission over one physical copper twisted pair with the 135 Ohm impedance according to ETSI TS 101 135.
User Manual ORDER INFORMA TION MDS932AE-10BT Modem AccessDSL Discovery, G.shdsl, 10/100Ba se-T Bridge, VLAN, Adapter 220 Vac MDS933AE-10BT Modem AccessDSL Discovery, G.shd sl, 1 or 2 pairs, up to 4.6Mbps, 10/100Base-T Bridge, VLAN, Adapter 220 Vac MDS932AE-FXS Modem AccessDSL Discovery, G.
User Manual 2 DESCRIPTION OF THE DEVICE 2.1 Exterior design Desktop models The front panel of the device has 3 LEDs: LOCAL informs the user about the status of the local device. The following four statuses are possible «blinking red» informs the user about malfunctioning of the modem’s hardware and software.
User Manual The back panel of the MDS932AE-10BT and MDS933AE-10BT modem has: • The grounding bolt of the modem (option); • The “AC12V” power connector.
User Manual 2.2 Exterior design rack card models.
User Manual Status(L) informs the user about the status of the local device. The following four statuses are possible «blinking red» informs the user about malfunctioning of the modem’s hardware and software. In this case, the modem is out of order and should be submitted to the service center for being repaired.
User Manual 3 RULES OF SWITCHING 3.1 The standalone delivery set The delivery set includes: • the subscriber access dev ice (a modem) • the power supply source (an AC adapter) • the cables for the line connections 3.
User Manual To update the information on the screen use the “Enter” key. The following menu will appear on the screen. Input Password: Please enter your programmed password. The unit will be delivered with the default password “admin” After entering the password the following menu will appear.
User Manual 4 THE COMMAND SYSTEM 4.1 Basic rules After the command is typed, press <enter>. The <Backspace> key is used to edit commands. It is necessary to input item number, for choising.
User Manual 4.3 Performance management submenu Upon activation of the performance management submenu the following message will be displayed. Performance Management 1.Loop Status... 4.EtherNet Status... Select item number or ESC to Upper level menu>> 4.
User Manual 4.3.2 Ethernet Status submenu Upon activation of the performance management submenu the following message will be displayed. Performance Management->EtherNet Status Link:Link down Link .
User Manual 4.4.1 DSL Setup In this menu you can setup the DSL link. When you have selected that menu, the following will appear: Configuration Management->DSL Setup 1.[Loop 1 Operation Mode]:Slave 2.[Loop 1 Auto/Fixed]:Fixed 5.[Loop 1 Fixed Connection Speed]:2312K(36N) 6.
User Manual 4.4.1.4 Fixed Connection Speed (only if Fixed is selected) • In the Fixed Connection Speed menu, you can specify your desired speed in the range of 72 kbps to 2312 kbps for 2wire units and 144 kbp s to 4624 kbps for 4wire models 4.4.1.5 Annex • With the Appendix menu you can choose between A, B, A / B.
User Manual 4.4.2 Ethernet Setup submenu Configuration Management->EtherNet Setup 1.[Speed]:Auto 2.[Duplex Mode]:Auto 3.[Disable Mac Filter]:No 4.IP Address>>192.168.5.105 5.Subnet Mask>>255.255.255.0 6.Gateway Address>>192.168.5.
User Manual 5 TECHNICAL SPECIFICA TIONS The main technical specifications of modems of the Black Box family are presented below in the table. Line interface.
User Manual 6 ST ORAGE CONDITIONS The equipment of the Black Box family while being packed should withstand all means of transport at a temperature in the range form -50 о С to +50 о С and the relative humidity of air up to 100% at 25 о С . The equipment can also withstand air-transport at a low air pressure of 12 kPa (90 Torr) at -50 о С .
User Manual 7 TERMS TO TRANSPORT The equipment of the Black Box family should be packed and transported by: • motor transport with an enclosed truck body; • enclosed railroad cars; • unpressurized airplanes and helicopters (up to 10000 m at an air pressure of 170 Torr); • river transport (in holds).
User Manual 8 CONNECT OR’S DESCRIPTION 8.1 DSL Connector Type: RJ-45, 8 pin Number Signal Assignment 1,2 NC - 3 LB,a Ttp (4W model only) 4 LA,a tip 5 LA,b ring 6 LB,b ring (4W model only) 7,8 NC - RJ-45 1 8 8.
User Manual 8.3 PC and Hub Connectors Type: RJ-45 Number PC assignment HUB assignment 1 Tx+ Rx+ 2 Tx- Rx- 3 Rx+ Tx+ 4 NC NC 5 NC NC 6 Rx- Tx- 7 NC NC 8 NC NC 18 RJ-45 8.4 Line1 and Line2 Connector Type: RJ-11, 4 pin Number Signal Assignment 1 NC - 2 LA,a tip 3 LA,b ring 4 NC - RJ-11 1 4 Version: 1.
User Manual Version: 1.2 Page. 25 of 25 9 DESCRIPTION OF INTERF ACE CABLES 9.1 Ethernet cable Side А Color of wire Side B 1 white/green 1 2 green/white 2 3 white/orange 3 4 blue/white 4 5 white/blue 5 6 orange/white 6 7 white/brown. 7 8 brown/white 8 9.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Black Box MDS932AE-FXS c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Black Box MDS932AE-FXS - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Black Box MDS932AE-FXS, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Black Box MDS932AE-FXS va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Black Box MDS932AE-FXS, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Black Box MDS932AE-FXS.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Black Box MDS932AE-FXS. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Black Box MDS932AE-FXS ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.