Manuel d'utilisation / d'entretien du produit VSG1432-B101 Series du fabricant ZyXEL Communications
Aller à la page of 408
www .zyxel.com www .zyxel.com VSG1432-B101 Series 802.1 1n Wireless VDSL2 4-port Gateway Copyright © 2010 ZyXEL Communications Corporation Firmware V ersion 1.
.
About This User's Guide VSG1432-B10 1 Series User ’s Guide 3 About This User's Guide Intended Audience This manual is intended for people who w ant to configure the Z yXEL Device using the web configur ator . Y ou should hav e at least a basic knowledge of T CP/IP networking concepts and topology .
About This User's Guide VSG1432-B101 Series User’s Guide 4 • Download Library Search for the latest produc t updates an d documentation from this link.
Document Conventions VSG1432-B10 1 Series User ’s Guide 5 Document Conventions W arnings and Notes These are how warnings and notes are shown in this User’ s Guide.
Document Conventions VSG1432-B101 Series User’s Guide 6 Icons Used in Figures Figures in this User’s Guide may use the followi n g generic icons. The Z yXEL Device icon is not an exact represent ation of your device.
Safety Warnings VSG1432-B10 1 Series User ’s Guide 7 Safety Warnings • Do NO T use this product near water , for ex am ple, in a wet basement or near a swim ming pool. • Do NO T expose your device to dampness, dust or corrosive liquids. • Do NO T store things on the device.
Safety Warnings VSG1432-B101 Series User’s Guide 8.
Contents Overview VSG1432-B10 1 Series User ’s Guide 9 Contents Overview User ’ s Guide ................................................... ..................................................... .......... ......... 21 Introducing the VSG1432-B101 .
Contents Overview VSG1432-B101 Series User’s Guide 10.
Table of Contents VSG1432-B10 1 Series User ’s Guide 11 Table of Contents About This User's Guide . ............................................................... ........................................ .. 3 Document Conventions..............
Table of Contents VSG1432-B101 Series User’s Guide 12 3.1 Overview ... ... .... ... ... ... ............. .... ... ... ... ... ............. .... ... ... ... .... ... ............. ... ... ... .... ... .... ............ 41 3.2 Quick S tart Setup ...
Table of Contents VSG1432-B10 1 Series User ’s Guide 13 6.3.4 IP Address Assignment .... ... ... ... ... ............. .... ... ... ... .... ... ... ... ... .... ............. ... ... ... ... .... ... 87 6.3.5 NA T ........... ... ... .... ... ... .
Table of Contents VSG1432-B101 Series User’s Guide 14 8.4 The UPnP Screen ......... ................ ................ ............. ................ ............. ................ ........ ... 1 33 8.5 Installing UPnP in Windows Example . ..........
Table of Contents VSG1432-B10 1 Series User ’s Guide 15 12.3 The Applications Screen ................... ....... ...... ............. ............. ................ ............. ........... 179 12.3.1 Add New Application .. ................ .......
Table of Contents VSG1432-B101 Series User’s Guide 16 16.1 Overview ........... ................ ............. ................ ................ ............. ................ ............ ......... 215 16.1.1 What Y ou Can Do in this Chapter ..... .
Table of Contents VSG1432-B10 1 Series User ’s Guide 17 21.1.1 What Y ou Can Do in this Chapter ..... ...... ............. ............. ................ ............. ........ 245 21.1.2 What Y ou Need to Know ............ ............. ...........
Table of Contents VSG1432-B101 Series User’s Guide 18 Chapter 26 IGMP St atus ............................................................... .................................................... ....... 279 26.1 Overview ........... ................
Table of Contents VSG1432-B10 1 Series User ’s Guide 19 Chapter 33 Diagnostic........................................................ ..................................................... ........... ...... 305 33.1 Overview ........... ............
Table of Contents VSG1432-B101 Series User’s Guide 20.
21 P ART I User ’ s Guide.
22.
VSG1432-B10 1 Series User ’s Guide 23 C HAPTER 1 Introducing the VSG1432-B101 1.1 Overview The VSG1432-B101 is a wirel e ss VDSL router and Gigabit Ethernet gateway . It has a DSL port and a Gigabit Ethernet p ort fo r sup er-fast Internet access over analog (POT S) telephone lines.
Chapter 1 Introducing th e VSG1432- B101 VSG1432-B101 Series User’s Guide 24 • W rite down the password and put it in a safe place. • Back up the configuration (and mak e sure you know how to restore it). Restoring an e arlier wo rking conf iguratio n may be usef ul if the device becomes unstable or even cr ashes.
Chapter 1 Introducing the VSG1432-B101 VSG1432-B10 1 Series User ’s Guide 25 Computers can connect to the Z y XEL Device’s LAN ports (or wirelessly). Figure 1 ZyXEL Device’ s Internet Access Application Y ou can also configure IP filtering on the Z yXEL Device for secure Internet access.
Chapter 1 Introducing th e VSG1432- B101 VSG1432-B101 Series User’s Guide 26 File Sharing Use the built -in USB 2.0 port to share f iles on a USB memory stick or a USB hard drive ( B ). Y ou can connect one USB hard drive to the ZyXEL Device at a time.
Chapter 1 Introducing the VSG1432-B101 VSG1432-B10 1 Series User ’s Guide 27 T o connect the stand, line up the arrow on the stand with the arrow on the bottom of the device as shown.
Chapter 1 Introducing th e VSG1432- B101 VSG1432-B101 Series User’s Guide 28 1.6 Hardware Connections T o connect your Z yXEL Device: Figure 4 Hardware Connections 1 Attach the antenna and point it up.
Chapter 1 Introducing the VSG1432-B101 VSG1432-B10 1 Series User ’s Guide 29 3 LAN : Use an Ethernet cable to connect a computer to a LAN port for initial configur ati on and/or Internet access. 4 USB : Connect a USB (version 2.0 or lower) memory stick or a USB hard drive for file sharing.
Chapter 1 Introducing th e VSG1432- B101 VSG1432-B101 Series User’s Guide 30 None of the LEDs are on if the Z y XEL Device is not receiving power . T able 1 LED Descriptions LED COLOR ST A TUS DESCRIPTION POWER Green On The Z yXEL Device is receiving power and ready for use.
Chapter 1 Introducing the VSG1432-B101 VSG1432-B10 1 Series User ’s Guide 31 1.8 The RESET Button If you forget your password or cannot acces s the web configurator , you will need to use the RE SET button at the back of the device to reload the factory -default configurati on file.
Chapter 1 Introducing th e VSG1432- B101 VSG1432-B101 Series User’s Guide 32 T o activate WPS: 1 Make sure the POWER LED is on and not blinking. 2 Press the WLAN/WPS button for five seconds and release it. 3 Press the WPS button on an other WPS-enabled device within range of the Z yXEL Device.
VSG1432-B10 1 Series User ’s Guide 33 C HAPTER 2 The Web Configurator 2.1 Overview The web configurator is an HTML -based management interface that allows easy device setup and management via Internet browser . Use Internet Explorer 6.0 and later version s or Mozilla F irefox 3 and la t er ver sions or Sa f a ri 2 .
Chapter 2 The Web Con figurator VSG1432-B101 Series User’s Guide 34 enter your password and click Login . For securit y reasons, you will be tempor arily denied access to the Z yXEL Devi ce for a pe.
Chapter 2 The Web Configurator VSG1432-B10 1 Series User ’s Guide 35 6 The Network Map page appears. Figure 10 Network Map Note: For security reasons, the ZyXEL Device automatically logs you out if you do not use the web configurator for ten minutes (defa ult).
Chapter 2 The Web Con figurator VSG1432-B101 Series User’s Guide 36 2.2 W eb Configurator Layout Figure 1 1 Screen Layout As illustr ated above, the main screen is divided into these parts: • A - title bar • B - main window • C - navigation panel 2.
Chapter 2 The Web Configurator VSG1432-B10 1 Series User ’s Guide 37 The icons provide the following functions. 2.2.2 Main Window The main window displays information and configurati on fields. It is discussed i n the rest of this d ocument. After you cli ck Status on the Network Map page, the Status screen is displa yed.
Chapter 2 The Web Con figurator VSG1432-B101 Series User’s Guide 38 Home Networking LAN Setup Use this screen to configure LAN TCP/IP settings, and other adva nced properties. Static DHCP Use this screen to assign specific IP addresses to individual MAC addresses.
Chapter 2 The Web Configurator VSG1432-B10 1 Series User ’s Guide 39 Par e n ta l Control Use this screen to block web sites with the specific URL. Scheduler Rule Use this screen to configure the days and times when a configured restriction (such as parental control) is enforced.
Chapter 2 The Web Con figurator VSG1432-B101 Series User’s Guide 40.
VSG1432-B10 1 Series User ’s Guide 41 C HAPTER 3 Quick Start 3.1 Overview Use the Quick Start screens to configure the Z yXEL Device’ s time zone and basic Internet access and wireless setting s. Note: See the techn ical reference chapters (st arting on p age 67 ) for background information on the features in this chapter .
Chapter 3 Quick Start VSG1432-B101 Series User’s Guide 42 2 Enter your PPPoE account’ s user name an d password exactly as provided by your Internet Service Provider (ISP). If your ISP also gav e you static IP address settings to use, select Yes and ent er them in the fields that display .
VSG1432-B10 1 Series User ’s Guide 43 C HAPTER 4 Tutorials 4.1 Overview This chapter shows you how t o use th e Z yXEL Devi ce’ s va rious features.
Chapter 4 Tutorials VSG1432-B101 Series User’s Guide 44 2 In this example, the DSL connection has the following information. 3 Select the Active check box. Enter the General and ATM PVC Configuration settings as prov ided above. Set the Type to ADSL .
Chapter 4 Tutorials VSG1432-B10 1 Series User ’s Guide 45 6 Click Apply to save your se t tin gs . 7 Y ou should see a summary of your new DSL connect ion setup in the Broadband screen as follows.
Chapter 4 Tutorials VSG1432-B101 Series User’s Guide 46 T ry to connect to a web site, such as zyxel .com to see if you ha ve correctly set up your Internet co nn ec ti on . Be sure to contact your service pro vider for any information you need to configure the WAN screens.
Chapter 4 Tutorials VSG1432-B10 1 Series User ’s Guide 47 1 Click Netw ork Settings > Wireless to open the General screen. Select More Secure as the security level and WPA-PSK as the s ec uri ty mo d e. C onf i gu re th e screen using the provided parameters (see page 46 ).
Chapter 4 Tutorials VSG1432-B101 Series User’s Guide 48 use the notebook’ s wireless client to search for the Z yXEL Device (see Section 4.3.3 on page 52 ).
Chapter 4 Tutorials VSG1432-B10 1 Series User ’s Guide 49 4 Push and hold the WPS button located on the ZyXEL Device’ s front panel for more than 5 seconds. Alternativ ely , you may lo g into Z yXEL Devi ce’ s web configur ator and go to the Network Settings > Wireless > WPS screen.
Chapter 4 Tutorials VSG1432-B101 Series User’s Guide 50 The following figure shows y ou an example of how to set up a wireless network and its security by pressing a button on both Z yXEL Device and wireless client.
Chapter 4 Tutorials VSG1432-B10 1 Series User ’s Guide 51 PIN Configuration When you use the PIN configuration meth od, y ou need to use both the Z yXEL Device’ s web configurator and the wireless client’ s utility . 1 Launch your wireless client’s configuration utility .
Chapter 4 Tutorials VSG1432-B101 Series User’s Guide 52 The following figure shows y ou how to set up a wireless network and it s security on a Z yXEL Device and a wireless client by using PIN method.
Chapter 4 Tutorials VSG1432-B10 1 Series User ’s Guide 53 Note: The ZyXEL Device supports IEEE 8 02.1 1b and IEEE 802.1 1g wireless clients. Make sure that your notebook or co mputer ’s wireless adapter support s one of these standards.
Chapter 4 Tutorials VSG1432-B101 Series User’s Guide 54 1 Click Network Settings > Wireless to open the General screen. Use this screen to set up the company’ s gener al wirele ss network group. Configure the screen using the provided par ameters and click Apply .
Chapter 4 Tutorials VSG1432-B10 1 Series User ’s Guide 55 3 Configure the screen using the pr o vided parameters and cl ick Apply . 4 In the More AP screen, click the Edit icon to configure the third wireless network group.
Chapter 4 Tutorials VSG1432-B101 Series User’s Guide 56 5 Configure the screen using the pr o vided parameters and cl ick Apply . 6 Check the status of VIP and Guest in the More AP screen. The yellow bulbs signify that the SSIDs are activ e and ready for wireless access.
Chapter 4 Tutorials VSG1432-B10 1 Series User ’s Guide 57 the Z y XEL Device. T raffic should be forw ar ded to t he port 666 of the Doom serv er computer which has an IP address of 192.168.1.34. Tutorial: NAT Port Forwarding Setup Thomas may set up the port settings by config uring the port settings for the Doom server computer (see Section 12.
Chapter 4 Tutorials VSG1432-B101 Series User’s Guide 58 3 The port forwarding settings y ou configured appear in the table. The ZyXEL Device forwards port 666 t raffic t o the computer with IP address 192.168.1.34. Players on the Internet then can ha v e access to Thomas’ Doom server .
Chapter 4 Tutorials VSG1432-B10 1 Series User ’s Guide 59 Y ou need to specify a static rout ing rule on the Z yXEL Device to specify R as the router in charge of forwarding tr affic to N2 . In this case, the Z yXEL Device routes traffic from A to R and then R routes the tr affic to B .
Chapter 4 Tutorials VSG1432-B101 Series User’s Guide 60 4a Select the Active check box. Enter the Route Name as R . 4b Ty p e 192.168.10 .0 and subnet ma s k 255.255.255.0 for the destination, N2 . 4c Ty p e 192.168.1. 253 ( R ’ s N1 address) in the Gateway IP Address field.
Chapter 4 Tutorials VSG1432-B10 1 Series User ’s Guide 61 Note: QoS is applied to traf fic flowing out of the ZyXEL Device. T raffic t hat does not match this class is assigned a priority queue based on the internal QoS mapping tabl e on the ZyXEL Device.
Chapter 4 Tutorials VSG1432-B101 Series User’s Guide 62 • Rate Limit : 5,000 (kbps) Tutor ia l: Advanced > Q oS > Queue Setup 3 Click Class Setup > Add new Classifier to create a new class. Chec k Active and follow the settings as shown in the screen below .
Chapter 4 Tutorials VSG1432-B10 1 Series User ’s Guide 63 This maps e-mail tr affic comi ng from port 25 to the highest priorit y , which you have created in the previous screen (see the IP Protocol field). This also maps your computer’ s IP addre ss and MA C address to the E-mail queue (see the Source fields).
Chapter 4 Tutorials VSG1432-B101 Series User’s Guide 64 • Configuring DDNS on Y ou r ZyXEL Device • T esting the DDNS Setting Note: If you have a private W AN IP address, then you cannot use DDNS. 4.8.1 Registering a DDNS Account on www .dyndns.
Chapter 4 Tutorials VSG1432-B10 1 Series User ’s Guide 65 • Enter the user na me ( UserName1 ) and password ( 12345 ). Click Apply . 4.8.3 T esting the DDNS Setting Now you should be able to access the Z yXEL Device from the Internet. T o test this: 1 Open a web browser on the comp uter (using the IP address a.
Chapter 4 Tutorials VSG1432-B101 Series User’s Guide 66 1 In FileZilla enter t he IP address of the Z yXEL Device (the default is 192.168.1.1), your account’ s user name and password and port 21 and click Quickconnect . A screen asking for password au thenticati on appears.
67 P ART II T echnical Reference.
68.
VSG1432-B10 1 Series User ’s Guide 69 C HAPTER 5 Network Map and Status Screens 5.1 Overview After you log i nto the W eb Confi gurator , the Ne twork Map screen app ears. This shows the network connection status of th e ZyXEL Device and clients connected to it.
Chapter 5 Network Map and Status Screens VSG1432-B101 Series User’s Guide 70 If you pref er to view the status in a list, click List View in the Viewing Mode selection box. Y ou can configure how often you want the ZyXEL Device to update this screen in Refresh Interval .
Chapter 5 Network Map and Status Screens VSG1432-B10 1 Series User ’s Guide 71 5.3 The S t atus Screen Use this screen to view the st atus of the Z yXEL Device. Click Status to open thi s screen. Figure 17 S tatus Screen Each field is desc ribed in the followi ng table.
Chapter 5 Network Map and Status Screens VSG1432-B101 Series User’s Guide 72 IP Subnet Mask This field displays the current subnet mask in the W AN. This field is av ailable only when your W AN type is IPoE or IPoA . W AN T y pe This field displays the current WAN connection type.
Chapter 5 Network Map and Status Screens VSG1432-B10 1 Series User ’s Guide 73 Status This field indicates whether or not the ZyXEL Device is using the interface. For the LAN interfaces or the Ethernet W AN interface, this field displays Up when the ZyXEL Device is using the interface and NoLink when the line is dis c o n nected.
Chapter 5 Network Map and Status Screens VSG1432-B101 Series User’s Guide 74.
VSG1432-B10 1 Series User ’s Guide 75 C HAPTER 6 Broadband 6.1 Overview This chapter describes how to configure W AN settings from the Broadband screen. Use this screen to configure yo ur Z yXEL Device for Internet access. A WAN (Wide Area Network) connection is an outside connection to another network or the Internet.
Chapter 6 Broadband VSG1432-B101 Series User’s Guide 76 W AN IP Address The WAN IP address is an IP address for the Z yXEL Device, which mak es it accessible from an outside network. It is used by the Z yXEL Device to communicate with other devices in other networks.
Chapter 6 Broadband VSG1432-B10 1 Series User ’s Guide 77 6.2 The Broadband Screen Use this screen to change y our Z yXEL De vice’ s Internet ac ce ss settings. Click Network Settings> Broadband from the menu. The summary table shows you the configured W AN services (connections) on the Z yXEL Device.
Chapter 6 Broadband VSG1432-B101 Series User’s Guide 78 6.2.1 Add/Edit Broadband Click Add new WAN interface in the Broadband screen or the Edit icon next to an existing W AN interface to configur e a W AN connection. The screen differs according to the mode and encapsulation you choose.
Chapter 6 Broadband VSG1432-B10 1 Series User ’s Guide 79 This screen displays when y ou select the Routing mode and PPPoE encapsulation. Figure 20 Broadband : Add/Edit: ADSL, PPPoE Encapsulation.
Chapter 6 Broadband VSG1432-B101 Series User’s Guide 80 The following table describes t he labels in this screen. T able 7 Broadband: Add/Edit: Routing Mode LABEL DESCRIPTION General Active Select this to activ ate the WAN configur ation settings. Name Specify a descriptive name of up to 15 alphanumeric char acters for this connection.
Chapter 6 Broadband VSG1432-B10 1 Series User ’s Guide 81 Encapsulation Mode Select the method of multiplexing used by yo ur ISP from the drop- down list box. Choices are: • LLC/SNAP-B RIDGING: In LCC encapsulation, bridged PDUs are encapsulated by identifying the type of the bridged media in the SNAP header .
Chapter 6 Broadband VSG1432-B101 Series User’s Guide 82 PPP Auto Connect Select this option if you do not want the connection to time out. IDLE Timeout This v alue specifies the time in minutes that elapses before the router automatically disconnects from the PPPoE serv er .
Chapter 6 Broadband VSG1432-B10 1 Series User ’s Guide 83 6.2.2.1 Bridge This screen displays when y ou select the Bridge mode. Figure 21 Broadband : Add/Edit: Bridge Mode DNS Select Dynamic if you want the ZyXE L Device use the DNS server addresses assigned by your ISP .
Chapter 6 Broadband VSG1432-B101 Series User’s Guide 84 The following table describes t he labels in this screen. T able 8 Broadband: Add/Edit: Bridge Mode LABEL DESCRIPTION General Active Select this to activ ate the WAN configur ation settings. Name Specify a descriptive name of up to 15 alphanumeric char acters for this connection.
Chapter 6 Broadband VSG1432-B10 1 Series User ’s Guide 85 P eak Cell Rate Divide the DSL line r ate (bps) by 424 (the size of an A TM cell) to find the Peak Cell R ate (PCR). This is the maximum rate at which the sender can send cells. T ype the PCR here.
Chapter 6 Broadband VSG1432-B101 Series User’s Guide 86 6.3 T echnical Reference This section provi des some technical background informatio n about the topics covered in th is ch apter . 6.3.1 Encap sulation Be sure to use the encapsulation method required by your ISP .
Chapter 6 Broadband VSG1432-B10 1 Series User ’s Guide 87 6.3.2 Multiplexing There are two conventions to identify what protocols the virtual circuit (VC) is carrying.
Chapter 6 Broadband VSG1432-B101 Series User’s Guide 88 6.3.5 NA T NA T (Network Address T ranslation - NA T , RFC 1631) is the transl ation of the IP address of a host in a packet, for exampl e, the source address of an outgoing packet, used wit hin one network to a di fferent IP address known within anot her network.
Chapter 6 Broadband VSG1432-B10 1 Series User ’s Guide 89 6.3.7 A TM T raffic Classes These are the basic A TM traffic classes defined by the A TM Forum T raffic Management 4.0 Specificati on. Const ant Bit Rate (CBR) Constant Bit R ate (CBR) provid es fixed bandwidth that is always a vail able even if no data is being sent.
Chapter 6 Broadband VSG1432-B101 Series User’s Guide 90 In Multi- T enant Unit (MTU) applications, VLAN is vital in p roviding isolation and security among the subscribers.
VSG1432-B10 1 Series User ’s Guide 91 C HAPTER 7 Wireless 7.1 Overview This chapter describes the Z y XEL Device’s Networ k Settings > Wireless screens. Use these screens to set up y o ur Z yXEL Device ’s wireless connec ti on . 7.1.1 What Y ou Can Do in this Chapter This section describes the Z y XEL Device’ s Wireless screens.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 92 7.1.2 What Y ou Need to Know Wireless Basics “Wireless” is essentially r adio communication. In the same w ay that walkie-tal kie radios send and receive information ov er the airwaves, wireless networking devices exchange informat ion with one anot her .
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 93 Click Netw ork Settings > Wireless to open the General screen. Figure 23 Network Settings > Wireless > General The following table describes t he genera l wireless L AN labels in this screen.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 94 P assphrase Ty p e If you set security for the wireless LAN and ha ve the Z yXEL Device generate a password, the setting in this field determines how the ZyXEL Device generates the password. Select None to set the Z yXEL Device’ s pa ssword gener ation to not be based on a passphrase.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 95 7.2.1 No Security Select No Security to allow wireless stations to communicate with the access points without any data encrypti on or authentication.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 96 The following table describes t he labels in this screen. 7.2.2 Basic (WEP Encryption) WEP encryption scrambl es the data transmi tted between the wireless stations and the access points (AP) to keep network c ommunications priv ate.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 97 The following table describes t he labels in this screen. T able 1 1 Wireless > General: Basic (WEP) LABEL DESCRIPTION Security Level Select Basic to enable WEP data encryption.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 98 7.2.3 More Secure (WP A(2)-PSK) The WP A-PSK security mode pro vides both improved d ata encryption and user authentication over WEP . Using a Pre-Sh ared K ey (PSK), both the Z yXEL Device and the connecting client share a co mmon password in order t o validate the connection.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 99 7.2.4 WP A(2) Authentication The WPA2 security mo d e is cu rrently th e most robust form of encryption for wireless networks. It requires a RADIUS se rver to authenticate user credentials and is a full implementation the securi ty protocol.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 100 Click Network Settings > Wireless to display the General screen. Select More Secure as the security level. Then select WPA or WPA2 from the Security Mode list. Figure 27 Wireless > General: More Secure: WP A(2) The following table describes t he labels in this screen.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 101 7.3 The More AP Screen This screen allows y ou to enable and conf igure multiple Basi c Service Sets (BS Ss) on the Z yXEL Device. Click Network Settings > Wireless > More AP . The following screen displays.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 102 7.3.1 Edit More AP Use this screen to ed it an SSID profile. Cl ick the Edit icon next to an SSID in the More AP screen. The following screen displays. Figure 29 More AP: Edit The following table describes t he fields in this screen.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 103 7.4 MAC Authentication This screen allows you to configure the Z y XEL Device to give exclusive ac cess to specific devi ces (Allow) or exclude specifi c devices from accessing the Z yXEL Device (Deny) .
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 104 Use this screen to view your Z y XEL Devi ce’ s MAC filter setting s and add new MAC filter rules. Click Wireless > MAC Authentication . The screen appears as shown. Figure 30 Wireless > MAC Authentication The following table describes t he labels in this screen.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 105 7.5 The WPS Screen Use this screen to configure WiFi Prot ected Setup (WPS) on your Z yXEL Device. WPS allows you to q uickly set up a wirele ss network with strong securit y , without having to conf ig ur e security se tt i ng s man ually .
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 106 7.6 The WMM Screen Use this scre en to enable Wi - Fi Mu ltiMedia (W MM ) and WMM Power Save in wireless networks for multimedia applications. Connect Click this button to add another WPS-enabled wireless device (within wireless range of the Z yXEL Device) to your wireless network.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 107 Click Network Settings > Wireless > WMM . The following screen displays. Figure 32 Network Settings > Wireless > WMM The following table describes t he labels in this screen.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 108 Click Network Settings > Wireless > WDS . The following screen displays. Figure 33 Network Settings > Wireless > WDS The following table describes t he labels in this screen.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 109 7.7.1 WDS Scan Y ou can click the Scan ic on in Wireless > WDS to have the Z yXEL Device automatically search and display the a vaila ble APs wi thin range. Select an AP and click Apply to have the Z yXEL Device establish a wireless li nk with the selected wireless device.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 11 0 7.8 The Others Screen Use this screen to configure ad vanced wireless settings. Cl ick Network Settings > Wireless > Others . The screen appears as shown. See Section 7.9.2 on page 113 for detailed defini tions of the terms listed in this screen.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 111 7.9 T echnical Reference This section discusses wireless LANs in depth. F or more information, see the appendix. 7.9.1 Wireless Network Overview Wireless networks c onsist of wireless clients, access points and bridges.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 11 2 • A wireless cl ient is a ra dio connected to a user’ s computer . • An access point is a r adio with a wired c onnection to a network, which can connect with numerous wireless clients and let them access the network.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 11 3 • If two wireless networks overlap , th ey should use a different channel. Like radio stations or television channels , each wireless net work uses a specific channel, or frequency , to send and receive information.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 11 4 7.9.3 Wireless Security Overview By their nature, rad io communications are si mple to intercept. F or wireless data networks, this means that anyone with in r ange of a wireless network without security can not only read the data passi ng over the airwav es , but also join the network.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 11 5 not broadcast the SSID . In additi on, you should change t he default SSID to something that is diffic ult to guess. This type of sec urity is fairly weak, howev er , because there are ways for unauthorized wirel ess devices to get the SSID.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 11 6 7.9.3.4 Encryption Wireless networks can us e encryption to protect the info rmation that is sent in the wireless network. Encryption is l ike a secret code. If you do not know the secr et code, you cannot unders tand the message.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 11 7 7.9.4 Signal Problems Because wireless networks are radio ne tworks, their signal s are subject to limitations of distanc e, interference and absorption. Problems with distance occur when the two r adios are too far apart.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 11 8 wireless station A and B can stil l access the wired network but cannot communicate with each other . Figure 37 Basic Service set 7.9.6 MBSSID T raditionally , you need to use different APs to configure different Basic Service Sets (BSSs).
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 11 9 7.9.7 Preamble T ype Preamble is used to signal that data is coming to the receiver . Short and long refer to the length of the synchronization field in a packet. Short preamble increases performance as less time sending preamble means more time for sending data.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 120 7.9.9 WiFi Protected Setup (WPS) Y our ZyXEL Device supports WiFi Protected Setup (WPS), which is an easy way to set up a secure wireless network. WPS is an industry standard specification, defined by the WiFi Alli ance.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 121 7.9.9.2 PIN Configuration Each WPS-enabled device has its own PIN (P ersonal Identification Number). This may either be static (it cannot be changed) or dynamic (in some devices you can generate a new PIN by clicki ng on a button in the configuration interface).
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 122 The following figure shows a WPS-enab led wi reless c lient (ins talled in a no tebook computer) connecting to the WPS- enabled AP via the PIN method. Figure 39 Example WPS Process: PIN Method 7.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 123 The following figure sh ows a WPS -en able d client (install ed in a notebook computer) connecting to a WPS-enabled access point. Figure 40 How WPS works The roles of registrar and enrollee last on ly as long as the WPS setup process is active (two minutes).
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 124 7.9.9.4 Example WPS Network Setup This section shows how security settings are distri buted in an example WPS setup. The following figure shows an example network. In step 1 , both AP1 and Client 1 are unconfigured.
Chapter 7 Wireless VSG1432-B10 1 Series User ’s Guide 125 point. However , you know that Client 2 supports the registrar function, so y ou use it to perform the WPS handshak e instead. Figure 43 WPS: Example Network S tep 3 7.9.9.5 Limit ations of WPS WPS has some limitations of which you should be a ware.
Chapter 7 Wireless VSG1432-B101 Series User’s Guide 126 • When you use the PBC method, there is a short period (from the moment you press the button on one device to the moment you press the button on the other device) when any WPS-enabled devi ce could join the network.
VSG1432-B10 1 Series User ’s Guide 127 C HAPTER 8 Home Networking 8.1 Overview A Local Area Network (LAN) is a shared communicat ion system to which many networking devices are connected. It is usually located in one immediate area such as a building or floor of a building.
Chapter 8 Hom e Netw or kin g VSG1432-B101 Series User’s Guide 128 8.1.2 What Y ou Need T o Know 8.1.2.1 About LAN IP Address IP addresses identify indi vidual devices on a network. Every networking device (including computers, serv ers, routers, printers, etc.
Chapter 8 Hom e Netw or king VSG1432-B10 1 Series User ’s Guide 129 • Dynamic port mapping • Learning public IP addresses • Assigning lease times to mappings Windows Messenger is an example of an application that supports NA T tr aversal and UPnP .
Chapter 8 Hom e Netw or kin g VSG1432-B101 Series User’s Guide 130 8.2 The LAN Setup Screen Use this screen to set the Lo cal Area Netw ork IP addr ess and su b n e t m a s k o f y o u r Z yXEL Device. Click Network Settings > Home Networking to open the LAN Setup screen.
Chapter 8 Hom e Netw or king VSG1432-B10 1 Series User ’s Guide 131 The following table describes t he fields in this screen. T able 24 Network Settings > Home Networking > LAN Setup LABEL DESCRIPTION Group Name Select the interface group name for which you want to configure LAN settings.
Chapter 8 Hom e Netw or kin g VSG1432-B101 Series User’s Guide 132 8.3 The S t atic DHCP Screen This table allows y ou to assign IP addresses on the LAN to specific individual computers based on their MAC Addresses. Every Ethernet dev ice has a unique MAC (Media Access Control) address.
Chapter 8 Hom e Netw or king VSG1432-B10 1 Series User ’s Guide 133 If you click Add new st atic lease in the Static DHCP screen or the Edit icon next to a static DHCP en tr y , th e following screen displays. Figure 46 S tatic DHCP: Add/Edit The following table describes t he labels in this screen.
Chapter 8 Hom e Netw or kin g VSG1432-B101 Series User’s Guide 134 Use the following screen to configure the UPnP settings on your Z yXEL Device. Click Network Settings > Home Networking > UPnP to displ a y the screen shown next.
Chapter 8 Hom e Netw or king VSG1432-B10 1 Series User ’s Guide 135 2 Click on the Windows Setup tab and select Communication in the Components selection box. Click Details . Add/Remove Programs: Wi ndows Setup: Communicatio n 3 In the Communications window , select the Universal Plug and Play check box in the Compone nts selection bo x.
Chapter 8 Hom e Netw or kin g VSG1432-B101 Series User’s Guide 136 4 Click OK to go back to the Add/Remove Programs Properties window and click Next . 5 Restart the computer when promp te d. Inst alling UPnP in Windows XP Fol low the steps below to install the UPnP in Windows XP .
Chapter 8 Hom e Netw or king VSG1432-B10 1 Series User ’s Guide 137 5 In the Networking Services window , select the Universal Plug and Play check box. Networki ng Services 6 Click OK to go back to the Windows Optional Networking Component Wizard window and click Next .
Chapter 8 Hom e Netw or kin g VSG1432-B101 Series User’s Guide 138 2 Right- click the icon and select Properties . Network Co nnection s 3 In the Internet Connection Properties window , click Settings to see the por t mappings there were automatically created.
Chapter 8 Hom e Netw or king VSG1432-B10 1 Series User ’s Guide 139 4 Y ou may edit or delete the port mappings or cl ick Add to manually add port mappings.
Chapter 8 Hom e Netw or kin g VSG1432-B101 Series User’s Guide 140 7 Double-click on the icon to display y o ur current In te rnet connection status. Internet Conn ection Status Web Configurator Eas y Access With UPnP , you can access the web-base d configur ator on the Z yXEL Device without finding out the IP address of the Z y XEL Device first.
Chapter 8 Hom e Netw or king VSG1432-B10 1 Series User ’s Guide 141 3 Select My Network Places under Other Places . Network Co nnection s 4 An icon with the description f or each UPnP-enabled device displays under Local Network . 5 Right- click on the icon for your Z yXEL Device and select Invoke .
Chapter 8 Hom e Netw or kin g VSG1432-B101 Series User’s Guide 142 6 Right- click on t he icon for y our Z yXEL Device and select Properties . A properties window displays with basic info rmatio n ab out the Z yXEL Device. Network Co nnection s: My Netw ork Plac es: Proper ties: Ex ample 8.
Chapter 8 Hom e Netw or king VSG1432-B10 1 Series User ’s Guide 143 8.7.1 LANs, W ANs and the ZyXEL Device The actual physical connec tion determines whether the Z yXEL Device ports are LAN or W AN ports. There are two sepa ra te IP networks, on e inside the LAN network and t he ot her outside th e WAN network as shown next.
Chapter 8 Hom e Netw or kin g VSG1432-B101 Series User’s Guide 144 • The ISP tells you the DNS serv er addresses, usually in the form of an info r mat io n sh e et, wh en yo u sig n u p. If you r ISP g ives yo u DNS s erve r addresses, enter them in the DNS Server fields in the DHCP Setup screen.
Chapter 8 Hom e Netw or king VSG1432-B10 1 Series User ’s Guide 145 The subnet mask specifies the network number portion of an IP address. Y our Z yXEL Devi ce will co mpute the subnet mas k automatically based on the IP address that you entered.
Chapter 8 Hom e Netw or kin g VSG1432-B101 Series User’s Guide 146.
VSG1432-B10 1 Series User ’s Guide 147 C HAPTER 9 Static Routing 9.1 Overview The Z yXEL Device usually uses the default gatewa y to route outbound tr affic from computers on the LAN to the Internet. T o have the Z yXEL Device send data to devices not reachable through the de fault g ateway , use static routes.
Chapter 9 Static Routing VSG1432-B101 Series User’s Guide 148 9.2 The Routing Screen Use this screen to view and configure th e static route rules on the ZyXEL Device. Click Network Settings > Routing > Static Route to open the foll owing sc reen.
Chapter 9 Static Routing VSG1432-B10 1 Series User ’s Guide 149 9.2.1 Add/Edit S t atic Route Use this sc reen to add o r edit a stat ic route. Click Add new Static Route Entry in the Routing screen or the Edit icon next to the stat ic route you want to ed it.
Chapter 9 Static Routing VSG1432-B101 Series User’s Guide 150.
VSG1432-B10 1 Series User ’s Guide 151 C HAPTER 10 Quality of Service (QoS) 10.1 Overview Quality of Service (QoS) refers to both a network’ s ability to deliver data with minimum delay , and the networking me thods used to control the use of bandwidth.
Chapter 10 Quality of Service (QoS) VSG1432-B101 Series User’s Guide 152 •T h e Monitor screen lets you view the Z yXEL Device's QoS-related pack et statistics ( Section 10.7 on page 165 ). 10.2 What Y ou Need to Know The following terms and conc epts may he lp as you read through this chapter .
Chapter 10 Quality of Service (QoS) VSG1432-B10 1 Series User ’s Guide 153 T raffic Policing T raffic pol ici ng is the limiting of the input or output transmission r ate of a class of traffic on the basis of user- defined criteria.
Chapter 10 Quality of Service (QoS) VSG1432-B101 Series User’s Guide 154 The following table describes t he labels in this screen. 10.4 The Queue Setup Screen Click Network Settings > QoS > Queue Setup to open the screen as shown next.
Chapter 10 Quality of Service (QoS) VSG1432-B10 1 Series User ’s Guide 155 Use this screen to conf igure QoS queue assignment. Figure 53 Network Settings > QoS > Queu e Setup The following table describes t he labels in this screen.
Chapter 10 Quality of Service (QoS) VSG1432-B101 Series User’s Guide 156 10.4.1 Adding a QoS Queue Click Add new Queue or the edit icon in the Queue Setup screen to configure a queue. Figure 54 Queue Setup: Add The following table describes t he labels in this screen.
Chapter 10 Quality of Service (QoS) VSG1432-B10 1 Series User ’s Guide 157 10.5 The Class Setup Screen Use this screen to add, edit or delete QoS classifiers.
Chapter 10 Quality of Service (QoS) VSG1432-B101 Series User’s Guide 158 To Q u e u e This is the name of the queue in which traffic of this classifier is put. Modify Click the Edit icon to edit the classifie r . Click the Delete icon to delete an existing classifier .
Chapter 10 Quality of Service (QoS) VSG1432-B10 1 Series User ’s Guide 159 10.5.1 Add/Edit QoS Class Click Add new Cl assifier in the Class Setup screen or the Edit icon next to a classifier to open the following screen.
Chapter 10 Quality of Service (QoS) VSG1432-B101 Series User’s Guide 160 The following table describes t he labels in this screen. T able 34 Class Setup: Add/Edit LABEL DESCRIPTION Active Select this to enable this classifier . Class Name Enter a descriptive name of up to 15 printable English keyboard characters, not including spaces.
Chapter 10 Quality of Service (QoS) VSG1432-B10 1 Series User ’s Guide 161 MAC Mask T ype the mask for the specified MAC address to determine which bits a packet’ s MAC address should match. Enter “f” for each bit of the spec ified source MAC address that the traffic’ s MAC address should match.
Chapter 10 Quality of Service (QoS) VSG1432-B101 Series User’s Guide 162 TCP A C K This field is available only when you select IP in the Ether Type field.
Chapter 10 Quality of Service (QoS) VSG1432-B10 1 Series User ’s Guide 163 10.6 The QoS Policer Setup Screen Use this screen to configure QoS policers that allow y ou to limit the transmis sion rate of incoming traffic. Click Network Settings > QoS > Policer Setup .
Chapter 10 Quality of Service (QoS) VSG1432-B101 Series User’s Guide 164 10.6.1 Add/Edit a QoS Policer Click Add new Of fice r in the Policer Setup screen or the Edit icon nex t t o a policer to show the following screen. Figure 58 Policer Setup: Add/Edit The following table describes t he labels in this screen.
Chapter 10 Quality of Service (QoS) VSG1432-B10 1 Series User ’s Guide 165 10.7 The QoS Monitor Screen T o view the ZyXEL Device’ s QoS packet statistics, click Network Settings > QoS > Monitor . The screen appears as shown. Figure 59 Network Settings > QoS > Monitor The following table describes t he labels in this screen.
Chapter 10 Quality of Service (QoS) VSG1432-B101 Series User’s Guide 166 10.8 T echnical Reference The following section contains additional technical information about the Z yXEL Device features de sc ri bed in this chapter . IEEE 802.1Q T ag The IEEE 802.
Chapter 10 Quality of Service (QoS) VSG1432-B10 1 Series User ’s Guide 167 DiffServ QoS is used to prioritize source-to- desti nat ion traffic flows. All packets in the flow are given the same priority . Y o u can use CoS (class of service) to give different priorities to different pac ket types.
Chapter 10 Quality of Service (QoS) VSG1432-B101 Series User’s Guide 168 Automatic Priority Queue Assignment If yo u e nab le Q oS on t he ZyXEL D evi ce , the Z y XEL Device can automaticall y base on the IEEE 802.1p priority lev el, IP prec edence and/or pac ket length t o assign priority to t raffic which does not match a clas s.
Chapter 10 Quality of Service (QoS) VSG1432-B10 1 Series User ’s Guide 169 T oken Bucket The token buck et algorithm uses tokens in a buc k et to control when tr affic can be transmit ted. The buck et stores tokens , each of which represents one byte.
Chapter 10 Quality of Service (QoS) VSG1432-B101 Series User’s Guide 170 All packets are ev aluated against the CBS. If a pac ket does not exc eed the CBS i t is marked green. Otherwise it is ev aluated against the EBS. If it is below the EBS then it is marked yellow .
VSG1432-B10 1 Series User ’s Guide 171 C HAPTER 11 Policy Forwarding 1 1.1 Overview T raditional ly , routing is based on the destination address only and the Z yXEL Device takes the shortest path to forwar d a packet.
Chapter 11 Policy F or wa rding VSG1432-B101 Series User’s Guide 172 1 1.2.1 Add/Edit Policy Forwarding Click Add new Policy Forward Rule in the Policy Forwarding screen or click the Edit icon next to a policy . Use this screen to configure the required information for a policy rou te .
Chapter 11 Policy Forwarding VSG1432-B10 1 Series User ’s Guide 173 WA N Select a WAN interface through which the tr affic is sent. Y ou must have the W AN interface(s) already configured in the Broadband screens. Apply Click Apply to save yo ur changes.
Chapter 11 Policy F or wa rding VSG1432-B101 Series User’s Guide 174.
VSG1432-B10 1 Series User ’s Guide 175 C HAPTER 12 Network Address Translation (NAT) 12.1 Overview This chapter discusses how to configure NA T on the ZyXEL Device.
Chapter 12 Network Address Translation (NAT) VSG1432-B101 Series User’s Guide 176 Global/Local Global/local denot es the IP address of a host in a packet as the pack et tr averses a router , for exa.
Chapter 12 Network A ddress Trans lation (NAT) VSG1432-B10 1 Series User ’s Guide 177 Note: Many residential broadband ISP accoun t s do not allow you to run any server processes (such as a We b or FTP server) from your location.
Chapter 12 Network Address Translation (NAT) VSG1432-B101 Series User’s Guide 178 The following table describes t he fields in this screen. 12.2.1 Add/Edit Port Forwarding Click Add new rule in the Port Forwarding screen or cl ick the Edit icon n ext to an existing rule to open the following screen.
Chapter 12 Network A ddress Trans lation (NAT) VSG1432-B10 1 Series User ’s Guide 179 The following table describes t he labels in this screen. 12.3 The Applications Screen This screen provides a summary of all NA T applications and their configur ation.
Chapter 12 Network Address Translation (NAT) VSG1432-B101 Series User’s Guide 180 T o access this screen, click Network Settings > NAT > Applications . The following screen appears. Figure 65 Network Settings > NA T > Applications The following table describes t he labels in this screen.
Chapter 12 Network A ddress Trans lation (NAT) VSG1432-B10 1 Series User ’s Guide 181 The following table describes t he labels in this screen. 12.4 The Port T riggering Screen Some services use a dedicated r ange of ports on the client side and a dedicated rang e of ports on the server sid e.
Chapter 12 Network Address Translation (NAT) VSG1432-B101 Series User’s Guide 182 For example: Figure 67 T rigger Port Forwarding Process: Example 1 Jane requests a file from the R eal Audio server ( port 7070). 2 P ort 7070 is a “trigger” port and causes t he Z yXEL Device to record Jane’ s computer IP address.
Chapter 12 Network A ddress Trans lation (NAT) VSG1432-B10 1 Series User ’s Guide 183 12.4.1 Add/Edit Port T riggering Rule This screen lets you create new port triggering rules. Click Add new rule in the Port Triggering screen or click a rule’ s Edit icon to open the following screen.
Chapter 12 Network Address Translation (NAT) VSG1432-B101 Series User’s Guide 184 The following table describes t he labels in this screen. T able 47 Port T riggering: Configuration Add/Edit LABEL DESCRIPTION Active Select the check box to enable this rule.
Chapter 12 Network A ddress Trans lation (NAT) VSG1432-B10 1 Series User ’s Guide 185 12.5 The DMZ Screen In addition to the servers for specified services, NA T supports a default server IP address. A default serv er rec eiv es pack ets from ports that are not specifi ed in the NAT Port Forwarding Setup screen.
Chapter 12 Network Address Translation (NAT) VSG1432-B101 Series User’s Guide 186 12.6 The ALG Screen Some NA T routers ma y include a SIP Application Lay er Gateway (AL G). A SIP ALG allows SIP calls to pass through NA T by examining and translating IP addres ses embedded in the data stream.
Chapter 12 Network A ddress Trans lation (NAT) VSG1432-B10 1 Series User ’s Guide 187 Click Network Settings > NAT > Sessions to displ a y the following screen. Figure 72 Network Settings > NA T > Sessions The following table describes t he fields in this screen.
Chapter 12 Network Address Translation (NAT) VSG1432-B101 Series User’s Guide 188 Note that inside/outside refers t o the locati on of a host, while gl obal/local refers to the IP address of a host used in a pack et.
Chapter 12 Network A ddress Trans lation (NAT) VSG1432-B10 1 Series User ’s Guide 189 12.8.3 How NA T Works Each packet has two addres ses – a source address and a destination address. For outgoing packets, t h e ILA (Inside Local Addr ess) is the source address on the LAN, and the IGA (Inside Global Address) is the source address on the W AN.
Chapter 12 Network Address Translation (NAT) VSG1432-B101 Series User’s Guide 190 12.8.4 NA T Application The following figure illustr ates a possible NA T application, where three inside LANs ( l o g i c a l L A N s u s i n g I P a l i a s ) b e h i n d t h e ZyXEL Device can communicat e with three distinct W AN networks.
Chapter 12 Network A ddress Trans lation (NAT) VSG1432-B10 1 Series User ’s Guide 191 Port Forwarding Example Let's say you want to assi gn ports 21-25 to o n e F T P , T e l ne t a n d S MT P s e rv e r ( A in the example), port 80 to another ( B in the example) and assign a default server IP address of 192.
Chapter 12 Network Address Translation (NAT) VSG1432-B101 Series User’s Guide 192.
VSG1432-B10 1 Series User ’s Guide 193 C HAPTER 13 Dynamic DNS Setup 13.1 Overview DNS DNS (Domain Name System) is for mapping a domain name to its corresponding IP address and vice v ersa. The DNS se rver is extremely important because without it, you must know the IP addre ss of a machine before you can access it.
Chapter 13 Dy namic DNS Se tup VSG1432-B101 Series User’s Guide 194 Figure 76 Example of DNS Routing T opology Dynamic DNS Dynamic DNS allows you to update your current dynamic IP a ddress with one or many dynamic DNS services so that anyo ne can contact you (in NetMeeting, CU- SeeMe, etc.
Chapter 13 Dynamic DNS Setup VSG1432-B10 1 Series User ’s Guide 195 you want to be able to use, for example, www .y ourhost.dyndns.org and still reach your hostname. If you have a pr ivate WAN I P add res s , the n you can n ot u se D y n am i c DNS.
Chapter 13 Dy namic DNS Se tup VSG1432-B101 Series User’s Guide 196 13.2.1 Add/Edit DNS Entry Y ou can manually add or edit the ZyXEL De vice’ s DNS name and IP address entry . Click Add new DNS entry in the DNS Entry screen or the Edit icon next to the entry you want to edit.
Chapter 13 Dynamic DNS Setup VSG1432-B10 1 Series User ’s Guide 197 The following table describes t he fields in this screen. T able 55 Advanced > DNS Setting > Dynamic DNS LABEL DESCRIPTION Dynamic DNS Select this check box to use dynamic DNS.
Chapter 13 Dy namic DNS Se tup VSG1432-B101 Series User’s Guide 198.
VSG1432-B10 1 Series User ’s Guide 199 C HAPTER 14 IGMP 14.1 Overview T raditionally , IP packets are transmitted in one of either two ways - Unicast (1 sender to 1 recipient) or Broadcast (1 sender to everybody on the network). Multicast deliv ers IP packets to just a group of hosts on the network.
Chapter 14 IG M P VSG1432-B101 Series User’s Guide 200 multicast hosts to learn the IP multic ast group membershi p. It checks IGMP packets pas sing through it, picks out th e group regist ration information, and configures multicasting accordingly .
Chapter 14 IGMP VSG1432-B10 1 Series User ’s Guide 201 The following figure shows a network example where A is the multicast source while computers 1, 2 and 3 are the receiv ers. In the figure A is connected to the upstream interface and 1, 2 and 3 are connected to the do wnstrea m interf ace.
Chapter 14 IG M P VSG1432-B101 Series User’s Guide 202 14.2 The IGMP General Screen Use the IGMP General screen to configure general IGMP proxy and IGMP packet processing settings. Click Network Settings > IGMP Setting > General to open the following screen.
Chapter 14 IGMP VSG1432-B10 1 Series User ’s Guide 203 Ignore IGMP report without router alert optio n Select this to discard IGMP report packets that do not include a router alert option. Ignore IGMP leave without router alert optio n Select this to discard IGMP leave pack ets that do not include a router alert option.
Chapter 14 IG M P VSG1432-B101 Series User’s Guide 204 14.3 IGMP Filter Configuration Use this screen to control IGMP access. Click Network Settings > IGMP Setting > IGMP Filter to open the following screen. Figure 82 Network Settings > IGMP Setting > IGMP Filter The following table describes t he fields in this screen.
Chapter 14 IGMP VSG1432-B10 1 Series User ’s Guide 205 Allow IGMP packets from Ethernet LAN port1 ~ 4 Select specific LAN Ethernet ports upon which to accept IGMP packets. Clear individual LAN Ethernet port options to discard IGMP packets received on those ports.
Chapter 14 IG M P VSG1432-B101 Series User’s Guide 206 14.3.1 IGMP Host Limit ation Edit Use this screen to control a LAN host’ s access to IGMP services through the Z yXEL Device. Click Network Settings > IGMP Setting > IGMP Filter and then a LAN host’s Edit icon to open the following screen.
Chapter 14 IGMP VSG1432-B10 1 Series User ’s Guide 207 14.3.2 IGMP Service Add Use this screen to add or edi t an IGMP multicast service domain. Click Network Settings > IGMP Setting > IGMP Filter > Add a new rule to open the following screen.
Chapter 14 IG M P VSG1432-B101 Series User’s Guide 208 14.3.3 IGMP Host Limit ation Add Use this screen to cont rol a LAN host’ s access to an IGMP multicas t service domain. Click Network Settings > IGMP Setting > IGMP Filter > Add a new host limitation to open the following screen.
Chapter 14 IGMP VSG1432-B10 1 Series User ’s Guide 209 14.4 IGMP ACL Configuration Use the IGMP Access Control List (ACL) to block or allow access to specific multicast media channels. Click Network Settings > IGMP Setting > IGMP ACL to open the following screen.
Chapter 14 IG M P VSG1432-B101 Series User’s Guide 210 14.4.1 IGMP ACL Add Use this screen to configure the multicast IP address of a multicast media channel to which you want to block or allow access. Click Network Set tings > IGMP Setting > IGMP ACL > Add a new rule to open the following screen.
VSG1432-B10 1 Series User ’s Guide 21 1 C HAPTER 15 Interface Group 15.1 Overview By default, all LAN and W AN interfaces on the Z yXEL Device are in the same group and can communicate with each other . Create interface groups to have the Z yXEL Device assign the IP addresses in diffe rent domains to different groups.
Chapter 15 In te r fac e Gr ou p VSG1432-B101 Series User’s Guide 212 In the following example, the cl ient that sends pack ets with the DHCP V endor ID option set to MSFT 5.0 (meaning it is a Windows 2000 DHCP client) is assigned the IP address 192.
Chapter 15 Interface Group VSG1432-B10 1 Series User ’s Guide 213 15.2.1 Interface Group Configuration Click the Add New Interface Group button in th e Interface Group screen to open the following screen. Us e this screen to create a new interface group .
Chapter 15 In te r fac e Gr ou p VSG1432-B101 Series User’s Guide 214 Automatically Add Clients With the following DHCP V endor IDs Enter the V endor Class Identifiers (DHCP Option 60) to identify LAN hosts to add to the interface group by criteria such as the type of the hardware or firmware.
VSG1432-B10 1 Series User ’s Guide 215 C HAPTER 16 Firewall 16.1 Overview This chapter shows you how t o enable an d configure the Z yXE L Device firewall. Use the firewall to protect your Z yXE L Device and network from attacks by hackers o n the Internet an d control a ccess to it.
Chapter 16 Firewall VSG1432-B101 Series User’s Guide 216 16.1.2 What Y ou Need to Know SYN Att ack A SYN attack floods a targeted system with a series of SYN packets .
Chapter 16 Firewall VSG1432-B10 1 Series User ’s Guide 217 16.2 The Firewall Screen Use this screen to set t he security le vel of the firewall on the Z yXEL Device. Firewall rules are grouped based on t h e direct ion of tr avel of packets to which they apply .
Chapter 16 Firewall VSG1432-B101 Series User’s Guide 218 Click Security Settings > Firewall > Protocol to display the following screen. Figure 93 Security Settings > Firewall > Proto col The following table describes t he labels in this screen.
Chapter 16 Firewall VSG1432-B10 1 Series User ’s Guide 219 16.3.1 Add a Protocol Use this screen to add a customized servic e rule that you can us e in the firewall’ s ACL rule configuration. C lick Add New Protocol Entry in the Protocol screen to display the following screen.
Chapter 16 Firewall VSG1432-B101 Series User’s Guide 220 16.4 The Access Control Screen Click Security Settings > Firewall > Access Control to display the following screen. This screen disp lays a list of the configured incoming or outg oing filterin g rules.
Chapter 16 Firewall VSG1432-B10 1 Series User ’s Guide 221 Src IP This displays the source IP addresses to which this rule applies. Please note that a blank source address is equiv alent to Any . Dst IP This displays the destination IP addresses to which this rule applies.
Chapter 16 Firewall VSG1432-B101 Series User’s Guide 222 16.4.1 Add/Edit an ACL Rule Click Add New ACL Rule or the Edit i con next to an existing ACL rule in the Access Control screen.
Chapter 16 Firewall VSG1432-B10 1 Series User ’s Guide 223 Select Protocol Select the transport layer protocol that defines your customized port from the drop-down list box. The specif ic protocol rule sets you add in the Security Settings > Fire wall > Protocol > Add screen display in this list.
Chapter 16 Firewall VSG1432-B101 Series User’s Guide 224.
VSG1432-B10 1 Series User ’s Guide 225 C HAPTER 17 MAC Filter 17.1 Overview This screen allows you to configure the Z y XEL Device to give exclusive ac cess to specific devices or ex clude specific devices from accessing the Z yXEL Device. Every Ethernet dev ice has a unique MAC (Media Access Control) address.
Chapter 17 MAC Filter VSG1432-B101 Series User’s Guide 226 The following table describes t he labels in this screen. T able 70 Security Settings > MAC Filter LABEL DESCRIPTION MAC Filter Setup MAC Filter Select En able to activate the MAC filter function.
VSG1432-B10 1 Series User ’s Guide 227 C HAPTER 18 Parental Control 18.1 Overview P arental control allows you to permit or block access to certain web sites from home network computers.
Chapter 18 Pare n ta l Cont ro l VSG1432-B101 Series User’s Guide 228 The following table describes t he fields in this screen. 18.2.1 Add/Edit Parent al Control Rule Click Add new rule in the P arental Control screen or click the Edit icon next to a rule to open the followi ng screen.
Chapter 18 Parental Control VSG1432-B10 1 Series User ’s Guide 229 The following table describes t he fields in this screen. T able 72 Parental Control: Add/Edit LABEL DESCRIPTION PC Name/IP/MAC Select the user that you want to apply this rule to from the drop-down list box.
Chapter 18 Pare n ta l Cont ro l VSG1432-B101 Series User’s Guide 230.
VSG1432-B10 1 Series User ’s Guide 231 C HAPTER 19 Scheduler Rules 19.1 Overview Y ou can define time periods and days du ring which the Z yXEL Device performs scheduled rules of certain features (suc h as Firewall Access Control, Parental Control) on a specific user in the Scheduler Rules screen.
Chapter 19 Sc he dule r R ules VSG1432-B101 Series User’s Guide 232 19.2.1 Add/Edit a Schedule Click the Add button in the Scheduler Rules screen or click the Edit icon next to a schedule rule to open the following screen. Use this screen to configure a restricted access schedule f or a specific user on y our network.
VSG1432-B10 1 Series User ’s Guide 233 C HAPTER 20 Certificates 20.1 Overview The Z yXEL Device can use certifica tes (als o called digital IDs) to authenticate users. Certificates are based on public-pri v ate key pairs. A certificate contains the certificate owner’ s identity and public k ey .
Chapter 20 Certificates VSG1432-B101 Series User’s Guide 234 20.3 The Local Certificates Screen Click Security Settings > Certificates to op en the Local Certificates screen. This is the Z yXEL Devi ce’ s summary list of certificates and ce rtificat io n requests .
Chapter 20 Certificates VSG1432-B10 1 Series User ’s Guide 235 20.3.1 Create Certificate Request Click Security Settings > Certificates > Local Certificates and then Create Certificate Request to open the following screen. Use this screen to hav e the Z yXEL Device gener ate a certification request.
Chapter 20 Certificates VSG1432-B101 Series User’s Guide 236 Figure 104 Certificate Req uest Created 20.3.2 Load Signed Certificate After you create a certificate request and ha ve it signed by a Ce.
Chapter 20 Certificates VSG1432-B10 1 Series User ’s Guide 237 Note: Y ou must remove any sp aces from th e certificate’ s filename before you can import it. Figure 105 Load Signed Certificate The following table describes t he labels in this screen.
Chapter 20 Certificates VSG1432-B101 Series User’s Guide 238 Note: Y ou must remove any sp aces from th e certificate’ s filename before you can import it. Figure 106 Import Loca l Certificate The following table describes t he labels in this screen.
Chapter 20 Certificates VSG1432-B10 1 Series User ’s Guide 239 If you click Import from file in the Import Local Certificate screen, the following screen is displa yed. Figure 107 Import Local Certifica te > Import from file The following table describes t he labels in this screen.
Chapter 20 Certificates VSG1432-B101 Series User’s Guide 240 Figure 108 Certificate Det ails The following table describes t he labels in this screen. T able 80 Certificate Details LABEL DESCRIPTION Name This field displays the identifying na me of this certificate.
Chapter 20 Certificates VSG1432-B10 1 Series User ’s Guide 241 20.4 The T rusted CA Screen Click Security Settings > Certificates > Trusted CA to open the following screen. This screen disp lays a summary lis t of certificates of the certification authorities that y ou have set the Z yXEL De vice to accept as tru s te d.
Chapter 20 Certificates VSG1432-B101 Series User’s Guide 242 20.4.1 V iew T rusted CA Certificate Click the View ic on in the Trusted CA screen to open the following screen. Use this screen to view in-dep th information about the certification authori ty’ s certificate.
Chapter 20 Certificates VSG1432-B10 1 Series User ’s Guide 243 20.4.2 Import T rusted CA Certificate Click the Import Certificate button in the Tru sted CA screen to open the following screen. The Z yXEL Device tr usts any v alid certificate sig ned by any of the imported trusted CA certificates.
Chapter 20 Certificates VSG1432-B101 Series User’s Guide 244 The following table describes t he fields in this screen. If you click Import from file in the Import Local Certif icate screen, the following screen is displayed.
VSG1432-B10 1 Series User ’s Guide 245 C HAPTER 21 IPSec 21.1 Overview A virtual priv ate network (VPN) pro vides secure communications between sit es without the expense of leased site-to-site lines. A s ecure VPN is a combination of tunneling, encryption, aut hentication, access control and auditing.
Chapter 21 IP Sec VSG1432-B101 Series User’s Guide 246 21.1.2 What Y ou Need to Know A VPN tunnel is usually established in two phases. Each phase establ ishes a security association (SA) , a contr act in dicating what securit y par ameters the Z yXEL Device an d the remote IPSec rout er will use.
Chapter 21 IPSec VSG1432-B10 1 Series User ’s Guide 247 Finding Out More See Section 21.4 on page 256 for adv anced technical information on IPSec VPN . 21.2 The IPSec S t atus Screen Click Security Settings > IPSec > Status to open the scr een as shown.
Chapter 21 IP Sec VSG1432-B101 Series User’s Guide 248 21.3 The IPSec Settings Screen The following figure helps explain the main fields in the web configur ator . Figure 1 16 IPSec Summary Fields Local and remote IP addresses must be st atic. Click Security Settings > IPSec to open the Settings screen.
Chapter 21 IPSec VSG1432-B10 1 Series User ’s Guide 249 21.3.1 Add/Edit IPSec Setting Click Add New Connection or a policy’ s Edit icon in the IPSec > Settings screen to edit VPN policies. Note: The ZyXEL Device uses the system default gateway interface’ s W AN IP address as its W AN IP address to set up a VPN tunnel.
Chapter 21 IP Sec VSG1432-B101 Series User’s Guide 250 Method field on the IPSec > Setting: Add/Edit screen. The following is the IPSec Setting - Auto(IKE) screen. Figure 1 18 Settings > Add/Ed it: Auto(IKE) The following table describes t he fields in this screen.
Chapter 21 IPSec VSG1432-B10 1 Series User ’s Guide 251 T unnel access from local IP addresses Specify the IP addresses of the devi ces behind the ZyXEL Device that can use the VPN tunnel. The local IP addresses m ust correspond to the remote IPSec router's config ured remote IP addresses.
Chapter 21 IP Sec VSG1432-B101 Series User’s Guide 252 Authentication Method Select Pre-Shared Key to use a pre-shared k ey for authentication. A pre-shared key identifies a communicating party during a phase 1 IKE negotiation.
Chapter 21 IPSec VSG1432-B10 1 Series User ’s Guide 253 21.3.1.2 Manual Key Setup Manual ke y management is useful if you have prob lems with Auto(IKE) key management. 21.3.1.3 Security Pa rameter Index (SPI) An SPI is used to distinguish different SA s terminating at the same destination and using the same IPSec protocol.
Chapter 21 IP Sec VSG1432-B101 Series User’s Guide 254 Current Z yXEL implementation assumes id entical outgoing and in coming SP Is . 21.3.2 Configuring Manual Key Y ou only configure VPN man u al key w h en yo u se lec t Manual in the Key Exchange Method field on the IPSec > Setting: Add/Edit screen.
Chapter 21 IPSec VSG1432-B10 1 Series User ’s Guide 255 T unnel access from local IP addresses Specify the IP addresses of the devi ces behind the ZyXEL Device that can use the VPN tunnel. The local IP addresses m ust correspond to the remote IPSec router's config ured remote IP addresses.
Chapter 21 IP Sec VSG1432-B101 Series User’s Guide 256 21.4 T echnical Reference This section provi des some technical background informatio n about the topics covered in th is ch apter . Encryption Algorithm Select DES , 3DES , AES(aes-cbc) or ESP_NULL from the drop-down list box.
Chapter 21 IPSec VSG1432-B10 1 Series User ’s Guide 257 21.4.1 IPSec Architecture The over all IPSec architecture i s shown as follows. Figure 120 IPSec Architecture IPSec Algorithms The ESP (Encaps.
Chapter 21 IP Sec VSG1432-B101 Series User’s Guide 258 21.4.2 Encap sulation The two modes of operation for IPSec VPNs are Transport mode and Tunnel mode.
Chapter 21 IPSec VSG1432-B10 1 Series User ’s Guide 259 21.4.3 IKE Phases There are two phases to every IKE (Internet K ey Exchange) negotiation – phase 1 (Authentication) and phase 2 (K ey Exc hange). A phase 1 exchange establishes an IKE SA and the second one uses that SA to negotiate SAs for IPSec.
Chapter 21 IP Sec VSG1432-B101 Series User’s Guide 260 21.4.4 Negotiation Mode The phase 1 Negot iation Mod e you select de termines how t he Security Association (S A) will b e established for each conn ection through IKE negotiations .
Chapter 21 IPSec VSG1432-B10 1 Series User ’s Guide 261 Transport mode ESP with authentication is not compatible with NA T . 21.4.6 VPN, NA T , and NA T T raversal NA T is incompat ible with the AH protocol in both transport and tunnel mode.
Chapter 21 IP Sec VSG1432-B101 Series User’s Guide 262 Finally , NA T is compatible with ESP in tunnel mode because integrity checks are performed over the combinat ion of the "original header plus original payload," which is unchanged by a NA T device.
Chapter 21 IPSec VSG1432-B10 1 Series User ’s Guide 263 21.4.7.1 ID T ype and Content Examples T wo IPSec routers must have matchi ng ID type and content configuration in order to set up a VPN tunnel. The two Z yXEL Devices in this example can complete negotiation and establish a VPN tunnel.
Chapter 21 IP Sec VSG1432-B101 Series User’s Guide 264 21.4.9 Diffie-Hellman (DH) Key Group s Diffie-Hellman (DH) is a publi c-key crypt o graphy protocol that allows two parties to establish a shared secret o ver an un secured communications channel.
VSG1432-B10 1 Series User ’s Guide 265 C HAPTER 22 Service Control 22.1 Overview This chapter provides information on the Service Control screens. Service Control allows you to manage your Z yXEL Device from a remote location through the following interfaces: •L A N •W A N Note: The ZyXEL Device is managed using the W eb Configurator .
Chapter 22 Serv ice Control VSG1432-B101 Series User’s Guide 266 Click Security Settings > Service Control to open the following screen. Figure 124 Security Settings > Service Control The following table describes t he fields in this screen.
VSG1432-B10 1 Series User ’s Guide 267 C HAPTER 23 ARP Table 23.1 Overview Address Resolution Protocol (ARP) is a pr otocol for mapping an Internet Protocol address (IP address) to a physi c al machine address, also known as a Media Access Control or MAC address, on the local area network.
Chapter 23 ARP Tab le VSG1432-B101 Series User’s Guide 268 23.2 ARP T able Screen Use the ARP table to view IP-to-MAC addr ess mapping(s). T o open this screen, click System Monitor > ARP Table . Figure 125 System Monitor > ARP T able The following table describes t he labels in this screen.
VSG1432-B10 1 Series User ’s Guide 269 C HAPTER 24 Logs 24.1 Overview The web configurator allows y ou to choos e which categories of events and/o r alerts to hav e the Z yXEL Device log and then displa y the logs or have the Z yXEL Device send them to an administr ator (as e-mail) or to a syslog server .
Chapter 24 L ogs VSG1432-B101 Series User’s Guide 270 Refer to the document ation of your syslog progr am for detail s. The following table describes the syslog sev erity levels. 24.2 The System Log Screen Use the System Log screen to see the system logs for the categories that y ou select in Maintenance > Log Setting .
Chapter 24 Logs VSG1432-B10 1 Series User ’s Guide 271 The following table describes t he fields in this screen. 24.3 The Security Log Screen Use the Security Log screen to see the security-related logs for the categories that you select . Clic k System Monitor > Log > Security Log to open the following screen.
Chapter 24 L ogs VSG1432-B101 Series User’s Guide 272 The following table describes t he fields in this screen. T able 98 System Monitor > Log > Security Log LABEL DESCRIPTION Level Select a severity level from the dr op-down list box. This filters search results according to the severity lev el you have selected.
VSG1432-B10 1 Series User ’s Guide 273 C HAPTER 25 Traffic Status 25.1 Overview Use the Traffic Status screens to look at network tr affic status and statistics of the WAN and LAN interfa ces. 25.1.1 What Y ou Can Do in this Chapter •U s e t h e WAN screen to view the W AN traffic statistics ( Sect ion 25.
Chapter 25 Tra ff ic St at us VSG1432-B101 Series User’s Guide 274 25.2 The W AN S t atus Screen Click System Monitor > Traf fic Status to open the WAN screen. The figure in this screen shows the number of bytes re ceiv ed and sent on the Z yXEL Device.
Chapter 25 Traffic Status VSG1432-B10 1 Series User ’s Guide 275 P ackets Sent Data This indicates the number of tr ansmitted packets on this interface. Error This indicates the number of fr ames with errors tr ansmitted on this interface. Drop This indicates the number of outgoing pack ets dropped on this interface.
Chapter 25 Tra ff ic St at us VSG1432-B101 Series User’s Guide 276 25.3 The LAN S t atus Screen Click System Monitor > Traffic Status > LAN to open the following screen. The figure in this screen shows the i nterface that is currentl y co nnected on the Z yXEL Device.
Chapter 25 Traffic Status VSG1432-B10 1 Series User ’s Guide 277 P ackets Sent Data This indicates the number of tr ansmitted packets on this interface. Error This indicates the number of fr ames with errors tr ansmitted on this interface. Drop This indicates the number of outgoing pack ets dropped on this interface.
Chapter 25 Tra ff ic St at us VSG1432-B101 Series User’s Guide 278.
VSG1432-B10 1 Series User ’s Guide 279 C HAPTER 26 IGMP Status 26.1 Overview Use the IGMP Status screens to look at IGMP group status and tr affic statistics .
Chapter 26 IG M P Stat us VSG1432-B101 Series User’s Guide 280 26.3 IGMP S t atistics Screen Use this screen to look at the current number of IG MP-rel ated packets received for each IGMP multicast group and from each LAN host. T o open this screen, click System Monitor > IGMP Group Status > IGMP Statistics .
Chapter 26 IGMP Status VSG1432-B10 1 Series User ’s Guide 281 Host Address This field displays the IP address of a LAN computer that has sent the Z yXEL Device IGMP-related p ackets. Last Report Time This field displays when the Z yXEL Device received the latest packet from this LAN IP address for this IGMP multicast group.
Chapter 26 IG M P Stat us VSG1432-B101 Series User’s Guide 282.
VSG1432-B10 1 Series User ’s Guide 283 C HAPTER 27 Users Configuration 27.1 Overview In the Users Configuration screen, y ou can view , add, and configure user accounts of the Z yXEL Device. 27.2 The Users Configuration Screen Click Maintenance > Users C onfiguration to open the following screen.
Chapter 27 Us er s Con fig ur a tion VSG1432-B101 Series User’s Guide 284 The following table describes t he labels in this screen. T able 103 Maintenance > Users Configuration LABEL DESCRIPTION Advanced Account Security T urn on advanced account securit y to enforce tighter security for the Z y XEL Device’ s user accounts.
Chapter 27 Users Config uration VSG1432-B10 1 Series User ’s Guide 285 27.2.1 Add/Edit a Users Account Use this screen to add or edi t a users account. Click Add new user in the Users Configuration screen or the Edit icon next to the user account you w ant to edit .
Chapter 27 Us er s Con fig ur a tion VSG1432-B101 Series User’s Guide 286 Expire Period Enter a number of days to specify how many days this user’ s password is available. Ret r y T i m e s The ZyXEL Dev ice can lock a user out if you use a wrong user name or password to log in the Z yXEL Device.
VSG1432-B10 1 Series User ’s Guide 287 C HAPTER 28 Remote Management 28.1 Overview This chapter explains how to confi gure the Z yXEL Device’ s TR -069 and TR -064 auto-configur a ti on settings.
Chapter 28 Remote Management VSG1432-B101 Series User’s Guide 288 Click Maintenance > Remo te Management > T R-069 Client to open the following screen.
Chapter 28 Remote Management VSG1432-B10 1 Series User ’s Guide 289 28.3 The TR-064 Screen TR -064 is a LAN-Side DSL CPE Configurat io n protocol defined by the DSL Forum.
Chapter 28 Remote Management VSG1432-B101 Series User’s Guide 290.
VSG1432-B10 1 Series User ’s Guide 291 C HAPTER 29 Time Settings 29.1 Overview This chapter shows you how to configure system related settings, suc h as system time, password, name, the domain name an d the inactivity timeout interv al.
Chapter 29 Ti m e Set tin gs VSG1432-B101 Series User’s Guide 292 The following table describes t he fields in this screen. T able 107 Maintenance > T ime Setting LABEL DESCRIPTION Current Date/Time Syst e m T im e This field displays the time and fate of your Z yXEL Device.
Chapter 29 Time Settings VSG1432-B10 1 Series User ’s Guide 293 End rule Configure the day and time when Da ylight Saving Time ends if you enabled Daylight Saving. Y ou can select a specific date in a particular month or a specific day of a specific week in a particular month.
Chapter 29 Ti m e Set tin gs VSG1432-B101 Series User’s Guide 294.
VSG1432-B10 1 Series User ’s Guide 295 C HAPTER 30 Logs Setting 30.1 Overview Y ou can configure where the ZyXEL Device sends logs and which logs and/or immediate alerts the Z yXEL Device records in the Logs Setting screen. 30.2 The Log Settings Screen T o change your Z yXEL Device’ s log settings, click Mainte nance > Logs Setting .
Chapter 30 Log s Set tin g VSG1432-B101 Series User’s Guide 296 The following table describes t he fields in this screen. T able 108 Maintenance > Logs Setting LABEL DESCRIPTION Sysl o g Logging The ZyXEL Device sends a log to an external syslog server .
Chapter 30 Log s Set ting VSG1432-B10 1 Series User ’s Guide 297 30.2.1 Example E-mail Log An "End of Log" message dis plays for each mail in whic h a complete log has been sent. The following is an example of a log sent by e-mail. • Y ou may edit the subject title.
Chapter 30 Log s Set tin g VSG1432-B101 Series User’s Guide 298.
VSG1432-B10 1 Series User ’s Guide 299 C HAPTER 31 Firmware Upgrade 31.1 Overview This chapter explains how t o upload new firmw are to your Z yXEL Devi ce. Y ou can download new firmware releases from your nearest Z yXEL FTP site (or www .zyxel.com) to use to upgrade y our device’ s performance.
Chapter 31 Firmware Upgrade VSG1432-B101 Series User’s Guide 300 After you see the firmwa re updating screen , wait two minutes before logging into the Z yXEL Device again. Figure 140 Firmware Upload ing The Z yXEL Device automatically restarts in this time causing a temporary network disconnect.
VSG1432-B10 1 Series User ’s Guide 301 C HAPTER 32 Configuration 32.1 Overview The Configuration screen allows you to backup and restore device configur ati ons. Y ou can also reset your devi ce settings back to the factory default . 32.2 The Configuration Screen Click Maintenance > Configuration .
Chapter 32 Con fig ur at ion VSG1432-B101 Series User’s Guide 302 Click Backup to sa ve the Z yXEL Device’ s current configuration to your computer . Restore Configuration Re store Configur ation allows yo u to upload a new or previously saved configur ation file from your computer to y our Z yXEL Device.
Chapter 32 Configuration VSG1432-B10 1 Series User ’s Guide 303 If the upload w as not successful, th e follo wing sc reen will appear . Clic k OK to go back to the Configuration screen.
Chapter 32 Con fig ur at ion VSG1432-B101 Series User’s Guide 304 32.3 The Reboot Screen System restart allows you to reboot th e Z yXEL Devi ce r emote ly without turning the power off . Y ou may need to do this i f the Z yXEL Device hangs, for example.
VSG1432-B10 1 Series User ’s Guide 305 C HAPTER 33 Diagnostic 33.1 Overview Y ou can use different diagnostic methods to test a connection and see detailed results. These read-only screens displa y in formation to help you identify problems with the Z yXEL Device.
Chapter 33 Diagnostic VSG1432-B101 Series User’s Guide 306 The following table describes t he fields in this screen. T able 1 1 1 Maintenance > Diagnostic > Ping & T raceRoute & NsLoo .
VSG1432-B10 1 Series User ’s Guide 307 C HAPTER 34 Troubleshooting This chapter offers some suggesti ons to solv e problems y ou might encounter . The potential problems are divided into the following categories . • P ower , Hardware Connections, and LEDs • Z yXEL Device Access and Login • Internet Access 34.
Chapter 34 Tro u blesh oo tin g VSG1432-B101 Series User’s Guide 308 2 Check the hardware connections. 3 Inspect your cables for damage. Cont act the vendor to replace any damaged cables. 4 T urn the Zy XEL Device off and on. 5 If the problem continues, contac t the vendor .
Chapter 34 Troubleshooting VSG1432-B10 1 Series User ’s Guide 309 • If you changed t he IP address ( Section 8.2 on page 130 ), use the new IP address. • If you c hanged the IP address and have f orgotten it, see the troubles hooting suggestions for I forgot the IP address for the Z yXEL Device.
Chapter 34 Tro u blesh oo tin g VSG1432-B101 Series User’s Guide 310 I cannot T elnet to the ZyXEL Device. 1 See the troubleshooting suggestions for I cannot see or access the Login screen in the web configu rator . Ignore the suggestions about your browser .
Chapter 34 Troubleshooting VSG1432-B10 1 Series User ’s Guide 31 1 I cannot access the Inter net through a DSL connection. 1 Make sur e yo u h ave th e DSL WAN port connecte d to a telephone jack (or the DSL or modem jack on a splitter if y ou have one).
Chapter 34 Tro u blesh oo tin g VSG1432-B101 Series User’s Guide 312 I cannot access the Internet anymore. I had access to the Internet (with the ZyXEL Device), but my Internet con nection is not av ailable anymore. 1 Y our session with the ZyXEL Device ma y ha v e expired.
Chapter 34 Troubleshooting VSG1432-B10 1 Series User ’s Guide 313 What is a Server Set ID (SSID)? An SSID is a name that uniquely id entifi es a wireless network. The AP and all the clients within a wireless network must use the same SSID . What wireless security modes does my ZyXEL Device support? Wireless security is vital to your net w ork.
Chapter 34 Tro u blesh oo tin g VSG1432-B101 Series User’s Guide 314.
VSG1432-B10 1 Series User ’s Guide 315 C HAPTER 35 Product Specifications The following tables summarize the Z yXEL Device’ s hardware and firm ware features. 35.1 Hardware S pecifications T able 1 12 Hardware Specificatio ns Dimensions 210 (L) x 153 (W) x 40 (H) mm We i g h t 471 g P ower Adaptor Output 12 V 1.
Chapter 35 Product Specifications VSG1432-B101 Series User’s Guide 316 35.2 Firmware S pecifications Operation Humidit y 20% ~ 85% RH (non-condensing) Storage Humidity 20% ~ 90% RH (non-condensing) T able 1 12 Hardware Specificatio ns (continued) T able 1 13 Firmware Specification s Default IP Address 192.
Chapter 35 Product Specifications VSG1432-B10 1 Series User ’s Guide 317 Logs Use logs for troubleshooting. Y ou can send logs from the Z yXEL Device to an external syslog server . Universal Plug and Play (UPnP) A UPnP-enabled device can dynamically join a network, obtain an IP address and convey its capabilities to other devices on the networ k.
Chapter 35 Product Specifications VSG1432-B101 Series User’s Guide 318 VDSL Standards ITU- T G.9 93.1 VDSL Annex A (North American) Standard ITU G.993.
Chapter 35 Product Specifications VSG1432-B10 1 Series User ’s Guide 319 ADSL Standards ADSL ITU- T G.992.1 (G.dmt), Annex A and ETSI TS 101 388 V1.3.1 (05/2002) 1TR112 (U-R2 Deutsche T elekom AG) V ersion 7.0 including support of Dying Gasp and report of Self - T est-Result (A TU- T Reg is t e r # 3 ) EOC as specified in ITU- T G.
Chapter 35 Product Specifications VSG1432-B101 Series User’s Guide 320 The following list, which is not exhaust ive , illust rates the standards supported in the ZyXEL Device.
VSG1432-B10 1 Series User ’s Guide 321 A PPENDIX A Setting up Y our Computer ’ s IP Address All computers must ha ve a 10M or 100M Ethernet adapter card and TCP/IP installed.
Appendix A Setting up Your Computer’s IP Address VSG1432-B101 Series User’s Guide 322 Windows 95/98/Me Click Start , Settings , Control Panel and double-click the Network icon to open the Network window .
Appendix A Setting up Your Computer’s IP Address VSG1432-B10 1 Series User ’s Guide 323 3 Select Microsoft from the list of manufacturers . 4 Select TCP/IP from the list of network protocols and then click OK . If you need Client for Microsoft Networks: 1 Click Add .
Appendix A Setting up Your Computer’s IP Address VSG1432-B101 Series User’s Guide 324 3 Click the DNS Configuration t ab. • If you d o not know your DNS information, select Disable D NS . • If you k now your DNS information, select Enable DNS and type the information in the fields below (y ou may not need to fill them all in).
Appendix A Setting up Your Computer’s IP Address VSG1432-B10 1 Series User ’s Guide 325 Windows 2000/NT/XP The following example figures use the defa ult Windo ws XP GU I theme. 1 Click start ( Start in Windows 2000/NT), Settings , Control Panel .
Appendix A Setting up Your Computer’s IP Address VSG1432-B101 Series User’s Guide 326 3 Right- click Local Area Connection and then click Properties . Figure 155 Windows XP: Control Panel: Ne twork Connections: Properties 4 Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and then click Properties .
Appendix A Setting up Your Computer’s IP Address VSG1432-B10 1 Series User ’s Guide 327 • If you ha ve a dynamic IP address cli ck Obtain an IP address automatically . • If you hav e a static IP address click Use the following IP Address and fill in the IP address , Subnet mask , and Default gateway fields.
Appendix A Setting up Your Computer’s IP Address VSG1432-B101 Series User’s Guide 328 •C l i c k OK when finished. Figure 158 Windows XP: Adva nced TCP/IP Properties 7 In the Internet Protocol T.
Appendix A Setting up Your Computer’s IP Address VSG1432-B10 1 Series User ’s Guide 329 If you hav e previously configur ed DNS servers, click Ad vanced and then the DNS tab to order them. Figure 159 Windows XP: Internet Protocol (T CP/IP) Properties 8 Click OK to close the Internet Protocol (TCP/IP) Properties window.
Appendix A Setting up Your Computer’s IP Address VSG1432-B101 Series User’s Guide 330 1 Click the Start icon, Control Panel . Figure 160 Windows V ista: S tart Menu 2 In the Control Panel , double-cli ck Network and Internet . Figure 161 Windows V ista: Control Panel 3 Click Network and Sharing Center .
Appendix A Setting up Your Computer’s IP Address VSG1432-B10 1 Series User ’s Guide 331 4 Click Manage network conne ctions . Figure 163 Windows V ista: Network and Sharing Center 5 Right- click Local Area Connection and then click Properties .
Appendix A Setting up Your Computer’s IP Address VSG1432-B101 Series User’s Guide 332 6 Select Internet Protocol Version 4 (TCP/IPv4) and click Properties . Figure 165 Windows V ista: Local Area Connection Properties 7 The Internet Protocol Versio n 4 (TCP/IPv4) Properties window opens (the General tab ).
Appendix A Setting up Your Computer’s IP Address VSG1432-B10 1 Series User ’s Guide 333 •C l i c k Advanced . Figure 166 Windows V ista: Intern et Protocol V ersion 4 (TCP/IPv4) Properties 8 If you do not know your gatewa y's IP address, remov e any previously i nstalled gateways in the IP Settings tab and click OK .
Appendix A Setting up Your Computer’s IP Address VSG1432-B101 Series User’s Guide 334 •C l i c k OK when finished. Figure 167 Windows V ista: Adva nced TCP/IP Properties 9 In the Internet Protoc.
Appendix A Setting up Your Computer’s IP Address VSG1432-B10 1 Series User ’s Guide 335 If you hav e previously configur ed DNS servers, click Ad vanced and then the DNS tab to order them.
Appendix A Setting up Your Computer’s IP Address VSG1432-B101 Series User’s Guide 336 Macintosh OS 8/9 1 Click the Apple menu, Control Panel and do uble-cl ick TCP/IP to open the TCP/ IP Control Panel .
Appendix A Setting up Your Computer’s IP Address VSG1432-B10 1 Series User ’s Guide 337 2 Select Ethernet built-in from the Connect via list. Figure 170 Macintosh OS 8/9: TCP/IP 3 For d ynamically assigned settings, select Using DHCP Server fro m the Configure: list.
Appendix A Setting up Your Computer’s IP Address VSG1432-B101 Series User’s Guide 338 Macintosh OS X 1 Click the Apple menu, and click System Preferences to open the System Preferences window . Figure 171 Macintosh OS X: Apple Menu 2 Click Netw ork in the icon bar .
Appendix A Setting up Your Computer’s IP Address VSG1432-B10 1 Series User ’s Guide 339 •F r o m t h e Configure box, select Manually . • T ype your IP address in the IP Address box. • T ype your subnet mask in the Subnet mask box. • T ype the IP address of yo ur Z yXEL Device in the Router address box.
Appendix A Setting up Your Computer’s IP Address VSG1432-B101 Series User’s Guide 340 2 Double-click on the profile of the network card you wish to configure.
Appendix A Setting up Your Computer’s IP Address VSG1432-B10 1 Series User ’s Guide 341 6 Click the Activate button to apply the changes. The following sc reen displays.
Appendix A Setting up Your Computer’s IP Address VSG1432-B101 Series User’s Guide 342 • If you ha ve a static IP address, ent er static in the BOOTPROTO= field. T ype IPADDR = followed by the IP address (in dotted decimal notation) and type NETMASK = followed by the subnet mask.
Appendix A Setting up Your Computer’s IP Address VSG1432-B10 1 Series User ’s Guide 343 V erifying Settings Enter ifconfig in a terminal screen to ch eck your TCP/IP properties. Figure 181 Red Hat 9.0: Checking TCP/IP Properties [root@localhost]# ifconfig eth0 Link encap:Ethernet HWadd r 00:50:BA:72:5B:44 inet addr:172.
Appendix A Setting up Your Computer’s IP Address VSG1432-B101 Series User’s Guide 344.
VSG1432-B10 1 Series User ’s Guide 345 A PPENDIX B IP Addresses and Subnetting This appendix introduces IP addresses and subnet masks. IP addresses identify indi vidual devices on a network. Every networking device (including computers, serv ers, routers, printers, etc.
Appendix B IP Addresses and Subnetting VSG1432-B101 Series User’s Guide 346 The following figure shows an example IP address in which the first three octets (192.
Appendix B IP Addresses and Subnetting VSG1432-B10 1 Series User ’s Guide 347 By conv ention, subnet masks alw ays cons ist of a continuous sequence of ones beginning from the leftmost bit of the mask, followed by a continuous sequence of zeros, for a total number of 32 bits.
Appendix B IP Addresses and Subnetting VSG1432-B101 Series User’s Guide 348 Not ation Since the mask is alw ays a continuo us number of ones beginning f rom the left, followed by a continuous number of zeros for the remainder of the 32 bit mask, you can simply specif y the number of ones instead of writing the v alue of each octet.
Appendix B IP Addresses and Subnetting VSG1432-B10 1 Series User ’s Guide 349 The following figure shows the company network before subnetting. Figure 183 Subnetting Example: Before Subnetting Y ou can “borrow” one of the host ID bits to divide the network 192.
Appendix B IP Addresses and Subnetting VSG1432-B101 Series User’s Guide 350 In a 25-bit subnet the host ID has 7 bits , so each sub-net work has a maximum of 2 7 – 2 or 126 possibl e hosts (a host ID of all zeroes is the subnet’ s address itself , all ones is the subnet’ s broadcast address).
Appendix B IP Addresses and Subnetting VSG1432-B10 1 Series User ’s Guide 351 Example: Eight Subnet s Similarly , use a 27-bit mask to create eight subnets (000, 001, 010, 011, 100, 101, 110 and 111). The following table shows IP address last octet values for each sub net.
Appendix B IP Addresses and Subnetting VSG1432-B101 Series User’s Guide 352 Subnet Planning The following table is a summary for subnet planning on a network with a 24-bit network number . The following table is a summary for subnet planning on a network with a 16-bit network number .
Appendix B IP Addresses and Subnetting VSG1432-B10 1 Series User ’s Guide 353 addresses, follow their instructions i n selecting th e IP addresse s and the sub n et mask.
Appendix B IP Addresses and Subnetting VSG1432-B101 Series User’s Guide 354.
VSG1432-B10 1 Series User ’s Guide 355 A PPENDIX C Pop-up Windows, JavaScript s and Java Permissions In order to use the web configurator yo u need to allow: • W eb browser pop-up wind ows from your device. • Jav aScripts (enabled by default). • Jav a permissions (enabled by default).
Appendix C Pop-up Windows, JavaScripts and Java Perm issions VSG1432-B101 Series User’s Guide 356 1 In Internet Explorer , select Tools , Internet Options , Privacy . 2 Clear the Block pop-ups check box in the Pop-up Blocker sect ion of the screen. This disables an y web pop-up block ers you may have enabled.
Appendix C Pop-up Windows, JavaScripts and Java Per missio ns VSG1432-B10 1 Series User ’s Guide 357 2 Select Settings… to open the Pop-up Blocker Settings screen. Figure 187 Internet Options: Privacy 3 T ype the IP address of your device (the web page that you do not want to have blocked) wi th the prefix “http://” .
Appendix C Pop-up Windows, JavaScripts and Java Perm issions VSG1432-B101 Series User’s Guide 358 4 Click Add to mo ve the IP address to the list of Allowed sites . Figure 188 Pop-up Blo cker Settings 5 Click Close to return to the Privacy screen. 6 Click Apply to save this setting.
Appendix C Pop-up Windows, JavaScripts and Java Per missio ns VSG1432-B10 1 Series User ’s Guide 359 1 In Internet Explorer , click Tools , Internet Options and then the Security tab. Figure 189 Internet Options: Secu rity 2 Click the Custom Level..
Appendix C Pop-up Windows, JavaScripts and Java Perm issions VSG1432-B101 Series User’s Guide 360 6 Click OK to close the window . Figure 190 Security Settings - Java Scripting Java Permissions 1 From Internet Explorer , click Tools , Internet Options and then the Security tab.
Appendix C Pop-up Windows, JavaScripts and Java Per missio ns VSG1432-B10 1 Series User ’s Guide 361 5 Click OK to close the window . Figure 191 Security Settings - Java JA V A (Sun) 1 From Internet Explorer , click Tools , Internet Options and then the Advanced tab.
Appendix C Pop-up Windows, JavaScripts and Java Perm issions VSG1432-B101 Series User’s Guide 362 3 Click OK to close the window . Figure 192 Java (Sun) Mozilla Firefox Mozilla Firefo x 2.0 screens are used here . Screens for other versions ma y vary .
Appendix C Pop-up Windows, JavaScripts and Java Per missio ns VSG1432-B10 1 Series User ’s Guide 363 Click Content .to show the screen below. Select the chec k boxes as shown in the following screen.
Appendix C Pop-up Windows, JavaScripts and Java Perm issions VSG1432-B101 Series User’s Guide 364.
VSG1432-B10 1 Series User ’s Guide 365 A PPENDIX D W ireless LANs Wireless LAN T opologies This section discuss es ad-hoc and infr astructure wi reless LAN topologies. Ad-hoc Wireless LAN Configuration The simplest WLAN configur ation is an in depend ent (Ad-hoc) WLAN that connect s a set of computers with wireless adapters (A, B, C).
Appendix D Wireless LANs VSG1432-B101 Series User’s Guide 366 with each other . When Intra-BS S is disabled, wireless cli ent A and B can still access the wired network but cannot communicate with eac h other .
Appendix D Wireless LANs VSG1432-B10 1 Series User ’s Guide 367 An ESSID (ES S IDentification) uniquely id entifies each ESS . All access points and their associated wirel ess clients within the same ESS must have the same ESSID in order to comm u nicate.
Appendix D Wireless LANs VSG1432-B101 Series User’s Guide 368 hidden node. Both stations (ST A) are with in range of the access point (AP) or wireless gatewa y , but out-of -range of ea ch other , so they canno t "h ear" each other , that is they do not know if the channel is currently being used.
Appendix D Wireless LANs VSG1432-B10 1 Series User ’s Guide 369 Fragment ation Threshold A Fragmentation Threshold is the maximum data fr agment size (between 256 and 2432 bytes) that can be sent in th e wireless network before the AP will fragment the packet into smaller dat a frames.
Appendix D Wireless LANs VSG1432-B101 Series User’s Guide 370 The following figure shows the relative ef fectiveness of these wireless security methods av ailable on your Z yXEL Device. Note: Y ou must enable the same wireless security settings on the Z yXEL Device and on all wireless clients that you want to associate with it.
Appendix D Wireless LANs VSG1432-B10 1 Series User ’s Guide 371 • Authorization Determin es the network services availabl e to authenticated users once they are connected to the network. •A c c o u n t i n g K eeps track of the client’ s network activity .
Appendix D Wireless LANs VSG1432-B101 Series User’s Guide 372 EAP (Extensible Authenticati on Protocol) is an authentication prot ocol that runs on top of the IEEE 802.1x transport mechanism in order to support multiple types of user authentic a ti on .
Appendix D Wireless LANs VSG1432-B10 1 Series User ’s Guide 373 T TLS supports EAP methods and legacy au thentication methods such as P AP , CHAP , MS-CHAP and MS-CHAP v2.
Appendix D Wireless LANs VSG1432-B101 Series User’s Guide 374 WP A and WP A2 Wi-Fi Protected Ac cess (WPA ) is a subset of the IEEE 802.11i standard. WP A2 (IEEE 802.11i) is a wireless se curity standard that defi nes stronger encryption, authentication and key management than WPA.
Appendix D Wireless LANs VSG1432-B10 1 Series User ’s Guide 375 The Message Integrity Check (MIC) is de signed to prevent an attacker from capturing data pack ets, altering them and resending them. The MIC pro vides a strong mathematical function in which the receiver and the transmitter each compute and then compare the MIC.
Appendix D Wireless LANs VSG1432-B101 Series User’s Guide 376 The Windows XP patch is a free download that adds WP A capabili ty to Windows XP's built-in "Z ero Configur ation" wirel e ss client. Howev er , you must run Windows XP to use it.
Appendix D Wireless LANs VSG1432-B10 1 Series User ’s Guide 377 2 The AP checks each wireless client's pa ssword an d allows it to join th e net w or k only if the password matches. 3 The AP and wireless clients gener ate a common PMK (P airwise Master K ey).
Appendix D Wireless LANs VSG1432-B101 Series User’s Guide 378 Antenna Overview An antenna couples RF signals onto air . A t ransmitter within a wireless device sends an RF signal to the antenna, whic h propagates the signal through the air . The antenna also operates in reverse by capturing RF signals from the air .
Appendix D Wireless LANs VSG1432-B10 1 Series User ’s Guide 379 T ypes of Antennas for WLAN There are two types of antennas used for wireless LAN applications. • Omni-directional antennas send the RF sign al out in all directions on a horizontal plane.
Appendix D Wireless LANs VSG1432-B101 Series User’s Guide 380.
VSG1432-B10 1 Series User ’s Guide 381 A PPENDIX E Services The following table lists some commonl y-used services and their associated protocol s and port n umbers. • Name : This is a short, descrip tive name for the service. Y ou can use this one or create a different one, if you like.
Appendix E Serv ices VSG1432-B101 Series User’s Guide 382 T able 130 Examples of Services NAME PROTOCOL PORT(S) DESCRIPTION AH (IPSEC_TUNNEL) User-Defined 51 The IPSEC AH (Aut hentica tion Header) tunneling protocol uses this service. AIM TCP 51 90 AOL ’s Internet Messenger service.
Appendix E S ervices VSG1432-B10 1 Series User ’s Guide 383 MSN Messenger TCP 1863 Microsoft Networks’ messenger service uses this protocol. NetBIOS TCP / U DP TCP / U DP TCP / U DP TCP / U DP 137 138 139 445 The Network Basic Input/Output System is used for communication between computers in a LAN.
Appendix E Serv ices VSG1432-B101 Series User’s Guide 384 SFTP TC P 115 The Simple F ile T ransfer Protocol is an old way of tr ansferring files between computers. SMTP TC P 25 Simple Mail T ransfer Protocol is the message-exchange standard for the Internet.
VSG1432-B10 1 Series User ’s Guide 385 A PPENDIX F Open Sof tware Announcement s End-User License Agreement for “VSG1432-B101” WARNING: Z y XEL Communications Co rp. IS WILLING TO LICENSE THE SOFTWARE T O YOU ONL Y UPON THE CONDITION THA T YOU ACCEPT ALL OF THE TERMS CONT AINED IN THIS LICENSE AG REEMENT .
Appendix F Op en Software Announceme nts VSG1432-B101 Series User’s Guide 386 backup copy of the Softw are and Documentation solely for archiv al, back -up or disaster recovery purposes. Y ou shall no t exceed the scope of the license granted hereunder .
Appendix F O pen Software Announcem ents VSG1432-B10 1 Series User ’s Guide 387 contact the appropriate soft ware vendor or manufacturer directly for technical support and customer service rel ated to its software and p roducts.
Appendix F Op en Software Announceme nts VSG1432-B101 Series User’s Guide 388 LIABILITY FOR CONSEQUENTIAL OR INCIDENT AL DAMAGES, TH E ABOVE LIMIT A TION MA Y NO T APPL Y TO YOU .
Appendix F O pen Software Announcem ents VSG1432-B10 1 Series User ’s Guide 389 effective if i t is in writing and signed b y both parties hereto. If any part of this License Agreement is found inv .
Appendix F Op en Software Announceme nts VSG1432-B101 Series User’s Guide 390 Everyone is permi tted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most sof tware are design ed to take away your freedom to share and change it.
Appendix F O pen Software Announcem ents VSG1432-B10 1 Series User ’s Guide 391 TERMS AND CONDITIO NS FO R COPYING, DISTRIBUTION AND MODIFICA TION 0. This License applies to an y program or other work which contains a notice placed by the copyright holder saying it ma y be distributed under the terms of this General Pu bli c License.
Appendix F Op en Software Announceme nts VSG1432-B101 Series User’s Guide 392 These requirements apply to th e modified work as a wh ole. I f identi fiable sec tions of that work are not derived fro.
Appendix F O pen Software Announcem ents VSG1432-B10 1 Series User ’s Guide 393 4. Y ou may not copy , modify , sublicense, or distribute the Program ex cept as expressly provided under this License.
Appendix F Op en Software Announceme nts VSG1432-B101 Series User’s Guide 394 places the Progr am under this License may add an expli cit geographi cal distribution li mitation excl uding those countries, so that distributi on is permitted only in or among countrie s not thus excl uded.
Appendix F O pen Software Announcem ents VSG1432-B10 1 Series User ’s Guide 395 END OF TERMS AND CONDITIONS All other trademarks or tr ade names mentio ned herein, if any , are the property of their respective owners. This Product includes ppp software under below l icense This directory contains source code and precompiled binaries f or ppp-2.
Appendix F Op en Software Announceme nts VSG1432-B101 Series User’s Guide 396 FITNESS FOR A P AR TICULAR PURPOSE AND NONINFRINGEMENT . IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FO.
VSG1432-B10 1 Series User ’s Guide 397 A PPENDIX G Legal Information Copyright Copyright © 2010 by Z yXEL Communications Corpor ation. The contents of this publication ma y not be reproduced in any.
Appendix G Legal Information VSG1432-B101 Series User’s Guide 398 • This dev ice must acc e pt any interf erence received, including interference that may cause undesired operations. This device has been tested and found to comply with the limits for a Clas s B digital device pursuant to P art 15 of th e FCC Rules.
Appendix G Legal Information VSG1432-B10 1 Series User ’s Guide 399 本機限在不干擾合法電臺與不受 被干擾保障條件下於室內使用。 減少電磁波影響，請妥適使用。 N.
Appendix G Legal Information VSG1432-B101 Series User’s Guide 400 Note Re pair or replacement, as provided under this wa rranty , is the exclusi ve remedy of the purchaser . This warranty is in lieu of all other warr anties, express or impli ed, including any implied w arr anty of merchantability or fitness for a particul ar use or purpose.
Index VSG1432-B10 1 Series User ’s Guide 401 Index A ACL rule 222 ACS 287 activation firewalls 217 SIP ALG 186 SSID 101 Address R esolution Protocol 267 administrator password 34 ADSL compliance 319.
Index VSG1432-B101 Series User’s Guide 402 firewalls 217 reset 303 restoring 302 static route 149 , 196 , 285 copyright 397 CoS 167 CoS technologies 152 creating certificates 235 CTS (Clear to Send).
Index VSG1432-B10 1 Series User ’s Guide 403 H hidden node 367 HT TP 190 humidity 316 I IANA 353 Internet Assigned Numbers Authority see IANA IBSS 365 ID type and content 262 IEEE 802.
Index VSG1432-B101 Series User’s Guide 404 MTU (Multi- T enant Unit) 90 multicast 76 IGMP 76 Multiple BSS, see MBS SID multiplexing 87 LLC -based 87 VC-based 87 N NA T 175 , 176 , 177 , 187 , 188 , .
Index VSG1432-B10 1 Series User ’s Guide 405 Quality of Service, see QoS R RADIUS 370 message types 371 messages 371 shared secret key 371 RADIUS server 11 5 registration product 400 related documen.
Index VSG1432-B101 Series User’s Guide 406 T T ag Control Information See TCI T ag Protocol Identifier See TPID TCI temperature 315 thresholds data fragment 11 0 , 11 3 RTS / C T S 11 0 , 11 3 time .
Index VSG1432-B10 1 Series User ’s Guide 407 note 400 WDS 107 , 11 9 compatibility 107 example 11 9 web config urator 33 login 33 passwords 33 , 34 WEP 11 6 WEP Encryption 97 , 98 WEP encryption 96 .
Index VSG1432-B101 Series User’s Guide 408.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté ZyXEL Communications VSG1432-B101 Series c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du ZyXEL Communications VSG1432-B101 Series - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation ZyXEL Communications VSG1432-B101 Series, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le ZyXEL Communications VSG1432-B101 Series va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le ZyXEL Communications VSG1432-B101 Series, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du ZyXEL Communications VSG1432-B101 Series.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le ZyXEL Communications VSG1432-B101 Series. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei ZyXEL Communications VSG1432-B101 Series ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
