Manuel d'utilisation / d'entretien du produit GZ3500T du fabricant Zenoah
Aller à la page of 18
GZ3500T GB-1 G B GZ3500T CHAIN SA W OWNER’S MANUAL G B 848CE093A0 (807).
GZ3500T GB-2 Read operator's instruction book before operating this machine. W ear head, e ye and ear protection. Use the chain saw with two hands. Wa r ning! Danger of kickback. Read, understand and follow all warnings. This saw is for trained tree service operators only .
GZ3500T GB-3 G B Contents 1. For Safe Operation ................................................................... 4 2. Symbols on the Machine .......................................................... 8 3. Installing Guide Bar and Saw Chain ........
GZ3500T GB-4 1. For safe operation W ARNING This chainsaw has been especially designed for tree maintenance and should therefor e only be used by trained operators when working on trees.
GZ3500T GB-5 G B (1) (2) (3) 20. Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building and potentially explosive at- mosphere. Exhaust fumes contain dangerous carbon monoxide. 21. Do not operate the chain saw in a tree unless specially trained to do so.
GZ3500T GB-6 W ORKING WITH TREE SER VICE CHAIN-SA WS FROM A R OPE AND HARNESS This chapter sets out working practices to reduce the risk of injury from tree service chainsaws when working at height from a r ope and harness.
GZ3500T GB-7 G B Gaining a good footing at the working position can be assisted by use of a temporary foot stirrup created from an endless sling. Starting the saw in the tree When starting the saw in .
GZ3500T GB-8 2. Symbols on the Machine The port to refuel “MIX GASOLINE” P osition: Recoil case (in front of the fuel cap) The port to top up chain oil P osition: Recoil case (under the oil cap) Setting the switch to the “O” position, the engine stops immediately .
GZ3500T GB-9 G B T ensioner screw Loosen Tighten Chain tensioner nut Chain cov er Tighten Open the box and install the guide bar and the saw chain on the power unit as follows: The saw chain has very sharp edges. Use thick pro- tective gloves for safety .
GZ3500T GB-10 NOTE NOTE 4. Pour in the r est of gasoline and agitate again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, suf ficient agi- tation is necessary for the engine to last long.
GZ3500T GB-11 G B Chain oil flow adjusting shaft Rich Lean Idle adjusting screw H needle L needle Chain oil Throttle interlock Throttle lev er Switch Fuel Chain oil Choke closed Open with throttle lev er Choke open 5. Operating the Engine It is very dangerous to run a chainsaw that mounts broken parts or lacks any par ts.
GZ3500T GB-12 Activate the br ake Release Switch • When the brake operates, release the throttle lever to slow down the engine speed. Continuous opera- tion with the brake engaged will generate heat from the clutch and may cause trouble. • At machine inspection prior to each job, check the operating condition of the brake following the steps.
GZ3500T GB-13 G B A log lying on the gr ound Saw down halfway , then roll the log over and cut from the opposite side. A log hanging off the ground In area A, saw up fr om the bottom one-third and finish by sawing down from the top. In ar ea B, saw down from the top one-third and finish by sawing up fr om the bot- tom.
GZ3500T GB-14 knob air cleaner cov er filter elements NGK CMR7H Fuel filter Oiling por t Oil filter inlet por t of the cooling air Oiling por t Grease por t Sprock et 7. Maintenance When returning the filter , use a pinch not to be folded the suc- tion pipe.
GZ3500T GB-15 G B Muffler Underside guard Chain cov er Chain catcher Spark arrester Guide muffler 7. Muffler Regularly inspect the muffler for loose fastening scr ews, damage and rust. If you find that exhaust gas leaked out, r emove the muf fler and insert a screwdriver into the exhaust port to remove the carbon.
GZ3500T GB-16 side of a cutter . If a gap is observed between them, the rail is normal. Otherwise, the bar rail is wor n. Such a bar needs to be corrected or r eplaced.
GZ3500T GB-17 G B 11. Specifications Cutting head: <Sprocket bar> Sprocket: .................................................................. 6T Chain speed at max. power ......................... 19.1 (m/s) Guide bar T ype: ...................
GZ3500T GB-18 12. Limited warranty Should any failure occur on the pr oduct under normal operating conditions within the applicable warranty pe- riod, the failed part will be replaced or repair ed free of charge by a ZENOAH authorized dealer .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Zenoah GZ3500T c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Zenoah GZ3500T - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Zenoah GZ3500T, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Zenoah GZ3500T va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Zenoah GZ3500T, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Zenoah GZ3500T.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Zenoah GZ3500T. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Zenoah GZ3500T ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
