Manuel d'utilisation / d'entretien du produit BRUSHCUTTERS BK3410FL du fabricant Zenoah
Aller à la page of 24
BK3410FL / BK3410FL-S BK4310FL / BK4310FL-S BRUSHCUTTERS 115 37 95-79 (006) OWNER’S MANUAL •B efore using our brushcutter, please read this manual carefully to understand the proper use of your unit.
2 SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
3 1. W arning labels on the machine (1) Read owner’s manual before operating this machine. (2) Wear head, eye and ear protection. (3) Wear foot protection. (4) Wear gloves. (5) Beware of thrown objects. (6) Warning / Attention (7) Keep all children, bystanders and helpers 15 meters away from the machine.
4 For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake.
5 2. Never use the product, (1) When the ground is slippery or when you can’t maintain a steady posture. (2) At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the working area.
6 to sound level and hours of operations for the product. ■ BEFORE STARTING THE ENGINE 1. The area within a perimeter of 15 m of the person using the product should be considered a hazardous area into which no one should enter. If necessary, yellow warning rope, warning signs should be placed around the perimeter of the area.
7 serious burns or electrical shock. ■ IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area.
8 This contact causes the blade to stop for an instant and then suddenly move or ”bounce” away from the object that was hit. The operator can lose control of the unit and the blade can cause serious personal injury to the operator or any person nearby if the blade contacts any part of the body.
9 insert the liner into the clutch housing, being careful to make sure that the hole on the end of the liner is facing directly upwards. When the hole reaches a point directly below the stopper, you will hear a clicking sound as the stopper moves into the hole to fix the liner into place.
10 2. Attach the lever as shown in the picture and screw it securely. (SE6) (1) Throttle lever (2) Hole (3) Throttle cable (4) Screw (5) Nut ■ ADJUSTING THROTTLE CABLE • Proper play of the throttle cable is 1–2mm. Place the throttle lever to the lowest speed position (i.
11 (Note that this is a left-turning screw.) (1) Bar (2) Holder B (3) Holder A 2. Attach the cover (SE11,(11)) and fix it with screw. 3. Insert blade between cutter holder A and cutter holder B. (SE11) 4. Attach cover and spring washer. (SE11) 5. Screw the bolt to fix them into place.
12 6. Fuel • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. •W ipe up all spills before starting the engine. • Make sure to stop the engine and allow it cool before refueling the unit. • Keep open flames away from the area where fuel is handled or stored.
13 • Keep the throttle lever set always to the idling position when starting or stopping the engine, or moving the machine. If the throttle lever is set to any position other than the idling position, the blade will begin to rotate, causing danger. • The engine might start after a delay.
14 Do not pull out the starter rope up to its end, and do not let the knob jump out of the right hand otherwise it may not return to its original position. 5. After the engine has started, open the choke gradually. 6. Allow the engine to run for 2 to 3 minutes to warm up.
15 (1) Area of the blade where the machine is prone to blade thrust • When using this machine, read and obey the precautions and instructions described in “Safety precautions” (pages 5 to 8) of this manual.
16 7. Operation 4. Use a slow, deliberate action to cut heavy growth. The rate of cutting motion will depend on the material being cut. Heavy growth will require slower action than will light growth. 5. Never swing the unit so hard as you are in danger of losing your balance or control of the unit.
17 of the spool. 4. Wind up the line in the correct direction as indicated on the spool. 5. Hook each end of the line in the slot on the edge of the spool, and then put the ends through the eyelets on the housing. Make sure that the spring and the washers are in place.
18 8. Maintenance ■ FUEL FILTER When you mount or dismount the fuel filter, be careful not to damage the rubber packing. A damaged rubber packing or insufficient mounting of the fuel filter will cause fuel to leak. Check how heavily the fuel filter is clogged from the fueling port of the fuel tank every 25 hours of use.
19 8. Maintenance on the side where the main pipe is installed, and mount the plug in its original position. 4. Wipe off the pushed-out grease, and mount the blade and the blade rest plate in their original positions. (1) Plug (2) Blade rest plate ■ FLEXIBLE SHAFT Apply grease to the flexible shaft every 25 hours use.
20 blade, and keep the machine in a safe place away from heat and humidity. (1) Tank cap (2) Fuel tank The engine revolution speed increases when you turn the idling adjustment screw clockwise, and decreases when you turn it counterclockwise. Standard idling revolution speed: 2,300 to 2,700 rpm (1) Idling adjustment screw (2) Rotation increases.
21 9. T rouble shooting 10. Disposal • When the symptoms in the left column do not improve after taking the measures in the right column, please contact the shop where you bought this product. • For the measures marked with ✩ , please buy ZENOAH’ s genuine parts at the shop where you bought this product.
22 Should any failure occur on the product under normal operating conditions within the applicable warranty period, the failed part will be replaced or repaired free of charge by a ZENOAH authorized dealer. WARRANTY PERIOD: Six (6) months after purchased by end-user subject to 12 months from produced month.
.
1-9, Minamidai, Kawagoe-city , Saitama, 350-1 165 Japan To Dealer: Please complete the following form at time of sale. Product Model: ZENOAH BK3410FL BK4310FL BK3410FL-S BK4310FL-S Date of Purchase: D / M / Y Purchaser: Dealer: Name: Name: Address/Phone: Address/Phone: Equipment No.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Zenoah BRUSHCUTTERS BK3410FL c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Zenoah BRUSHCUTTERS BK3410FL - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Zenoah BRUSHCUTTERS BK3410FL, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Zenoah BRUSHCUTTERS BK3410FL va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Zenoah BRUSHCUTTERS BK3410FL, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Zenoah BRUSHCUTTERS BK3410FL.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Zenoah BRUSHCUTTERS BK3410FL. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Zenoah BRUSHCUTTERS BK3410FL ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
