Manuel d'utilisation / d'entretien du produit 980293-001 du fabricant Zebra Technologies
Aller à la page of 28
User’s Manual No. 980293-001 Rev. A ©1999 Zebra Technologies Corporation LP2824 Thermal Printer User’s Manual.
FOREWORD This manual provides installation and operation information for the LP2824 series printers, manu - factured by Zebra Technologies Corporation, Camarillo, California. COPYRIGHT NOTICE This document contains information proprietary to Zebra Technologies Corporation.
WARRANTY INFORMATION We Need To Hear From You! To Establish Your Warranty Period And Provide Access To Technical Support, Send Us Your Product Registration Card Today! Zebra Technologies Corporation w.
SHOCK HAZARD WARNING: The printer and power supply should never be operated in a location where either one can get wet. Personal injury could result. MEDIA WARNING: Always use high quality Eltron approved labels, tags and transfer ribbons.
980293-001 Rev. A v TABLE OF CONTENTS Installation and Operation .................1 Unpacking Your Printer ....................2 Getting To Know Your Printer .................3 Installation ...........................4 AutoSense Gap Sensor Adjustment .
vi 980293-001 Rev. A.
1 Installation and Operation This section provides information on the installation and operation of the printer. The printer is a low cost, desktop direct thermal printer. The printer is specifically designed for printing labels, tags or continuous receipts (with or without bar codes) from any DOS™, Win- dows™or ASCII-based compatible host.
Unpacking Your Printer 2 980293-001 Rev. A Installation and Operation User Documentation &S o f t w a r e.
Getting To Know Your Printer 980293-001 Rev. A 3 Installation and Operation.
Installation The following steps will guide you through the installation of the printer and software. Step ➊ Attach Power Supply To The Printer See the SHOCK HAZARD WARNING on page iv.
Step ➋ Attach Interface Cable The printer has either a parallel interface or a serial interface (with optional RJ-11 connector). For additional information on serial cable wir - ing, refer to Appendix A.
Step ➌ Load Labels 6 980293-001 Rev. A Installation and Operation MO VIE Open Cover Power ON Adjust Holders 1.0 inch 2.5 cm 1.5 inch 3.8 cm MO VIE.
Load Labels - continued If the indicator remains dark, see Appendix A - Troubleshooting. 980293-001 Rev. A 7 Installation and Operation Install Roll Thread Through Guides Close Cover Tap Feed Button.
Step AutoSense Gap Sensor Adjustment Perform this procedure when loading a new roll. If your printer has the label dispenser option, turn OFF the label taken sensor.
AutoSense Gap Sensor Adjustment - continued If the indicator remains orange or red, see the troubleshooting steps. 980293-001 Rev. A 9 Installation and Operation When Indicator Flashes, Release Feed Button 4 MO3351F 16 V3.21 Serial port : 96,N,8,1 Image buffer size:245K Fmem:000,0K,019.
Label Dispenser Option 10 980293-001 Rev. A Installation and Operation Open Door Use a Stylus to Switch On the Label Taken Sensor Remove Several Labels Push Liner Through Slot Close Door MO VIE.
Using Fan-Fold Media 980293-001 Rev. A 11 Installation and Operation Open Guides to Width of Media Lock Guides in Place Thread Media Through Guides Insert Media.
Step ➎ Install Software Start your computer and follow the installation instructions on the compact disc (CD). 12 980293-001 Rev. A Installation and Operation.
Appendix A - Troubleshooting Problem Solution or Reason STATUS Indicator Does not light when power switch is turned to ON (I) position. 1. Check power connections from A.C. outlet to power supply to printer. Lights GREEN, but printer will not print. 1.
Problem Solution or Reason Prints only partial label or skips a label. 1. Perform AutoSense gap sensor adjustment on page 8. 2. Label caught on print head. 3. Print head is not properly latched. 4. Possible software problem. Check the printer memory configuration.
Other Support Resources The first troubleshooting reference source is the table on the previous page. Next, contact the dealer where you purchased your printer. Zebra Technologies also provides a variety of information and user support services: • Internet : http://www.
Serial Interface Cable Wiring The figure below displays the cable wiring required to use the printer's RS-232 serial interface. 16 980293-001 Rev.
Cash Drawer Cable Wiring The figure below displays the pin assignments for the printer's retail cash drawer interface. Re - fer to the cash draw manufacturer's documenta - tion for proper drawer wiring. *+24 volts D.C. at no greater than 1.5 amps.
Parallel Interface Cable Wiring The figure below displays the cable wiring required to use the printer's Centronics parallel interface. +5 volts at 300 mA for external device (e.g. KDU or scanner) Appendix A - Troubleshooting 18 980293-001 Rev. A PRINTER DB - 25 Pi n No .
Cleaning the Print Head When you load new media, you can also clean the print head. 980293-001 Rev. A 19 Appendix A - Troubleshooting Rub Cleaning Pen Across Dark Area of Print Head Wait One Minute Be.
Appendix B - Accessories Accessories available for the printer are listed below. Always refer to the ELTRON part num - ber when placing an order. For the name of an Eltron brand dealer in your area, call: 1(805) 579-1800 or the nearest Zebra Technologies office (located on the back of this manual).
.
World Wide Offices: Zebra Technologies Corporation Eltron Products 1001 Flynn Road Camarillo, CA 93012-8706 USA Phone: +1 (805) 579 1800 FAX: +1 (805) 579 1808 e-mail: sales@eltron.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Zebra Technologies 980293-001 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Zebra Technologies 980293-001 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Zebra Technologies 980293-001, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Zebra Technologies 980293-001 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Zebra Technologies 980293-001, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Zebra Technologies 980293-001.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Zebra Technologies 980293-001. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Zebra Technologies 980293-001 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
