Manuel d'utilisation / d'entretien du produit R1 Extender du fabricant Z-Com
Aller à la page of 20
R1 Extender Quick Installation Guide V1.0 January 2009.
Copyright Copyright © 2008 all right s reserved. No pa rt of this publication may be reproduced, adapted, stored in a retrieval system, translated in to any language, or transmitted in any form or by any means without the written permi ssion of the supplier .
Chapter 1 Introduction Introduction The R1 Extender is a high-performance out door-deployable wireless bridg e that provides wireless connectivity among multiple network locations. It supports Ba se S tation, CPE, PTP and PTMP connectivity . Moreover , the R1 Ext ender has a built-in 23dBi pl anar antenna that can deliver up to a 40Km connection.
Chapter 2 Prep aration before Inst allation This chapter describes safety precaut ions and product information you have to know an d check before installi ng R1 Extender .
Product Package The product pa ckage you have received should cont ain the followi ng items. If any of them are not included or damaged, plea se contact your local vendor for support.
10. Wood Screw × 4 (for W all Mount) 11. W all/Gyprock Plug × 4 (for W all Mount) W aterproof RJ-45 Connector Kit 1. Gland × 1 2. Sealing Nut × 1 3.
Chapter 3 System Inst allation Assemble the Mounting Bracket 1. Place the main bracket into the seating and use a sp anner to fasten the bracket to the R1 Extender with M5×16 screws ⑧ and M5 washers ⑨ provided in the hardware packet s; 2.
Pole Mounting 1. Install the main bra cket and the pole mount bar ③ over the top of the pole by securing the drill holes of the pole mount bar to the main bracket ones an d insert two M8×80 ④ screws, spring washers ⑥ and washers ⑤ through the drill holes and main bracket; 2.
Connect Up Before installi ng the Ethernet cable with a wate rproof RJ-45 co nne ctor , it is recommended that the Cat-5 RJ-45 coaxial cable be used f or t he bridge to power injector conn ections.
Ground the wire The R1 Extender is shipped with a grounding wire. The unit must be properly grou nded to protect against power surges. The grounding point can be found on the bottom of the unit. It is supplied with an appropriat e grounding lug for attach ment to the ODU.
Make sure PoE is correctly connected to the RJ-45 port on the R1 Extender labeled PoE+Data. DO NOT connect to the port labeled “Wa rning!! No POE” , otherwise the extender will be severely damage .
Chapter 4 Configuration Connect the R1 Extender to a Local Computer If you are configuring the R1 Extender locally (without connecting its power injector to a wired LAN), connect a PC to the power injector ’s Et hernet port using a Category 5 Ethernet cable.
Considering convenient configuration, it is recommended to configure lo cal and remote R1 Extender respectively on two computer s. TTL time may vary depending on the operating sy stem.
How to Est ablish Wireless Bridge Mode The R1 Extender support s four operating modes, which are Base S tation, CPE, Peer-to-Peer (CSMA) and Peer-to-Peer (TDMA). Normally , Wireless Bridge i s the typical mode on this unit. Here we will illustrate how to est ablish wireless bridge con nectivity with R1 Extender .
192.168.1.2 and set the IP Subnet Mask on both as 255.255.255.0 W arning: Each IP add ress is uni que within a LAN, otherwise IP collision may occur! Open “ Radio ” in “ Wireless ” and you wi ll find the default operating mode is Peer-to-Peer (CSMA).
Login the We b-based interface of remote R1 Extender , open “ About ” in “ System ” and record the wireless MAC address of it. Login the We b-based interface of local R1 Extender and open “ .
W arning: The MAC address on the hou sing of R1 Extender is the ETH MAC address; therefore it can not be used in Peer-to-Peer links. The IP address of your PC should be in the same network segme nt to the one of bridges. Use ping to check whether the link between the two R1 Extender is OK.
both R1 Extenders are inst alled long distance ap art. Login the Web-ba sed interface of the local R1 Extender and open “ Peer-to-Peer Setup ” in “ Wireless ”. Hit “ Align A ntenna ” button, an antenna alignment tool will popup. S pecify the T arget RS SI and click “ Star t ” to begin the antenna alignment.
Chapter 5 T roubleshooting This chapter provides troubleshooting procedure s for basi c problems with the R1 Extender . Q 1. What if my R1 Extender fails to connect to the remote one? • Ethernet Link : Check the availability of power to the bridge by observing the LED status on the power inje cto r .
Chapter 6 Serv ice Information Page 20 Chapter 6 Service Information If you have any further trouble using the R2 Ext ender or you would like to require additional support, you may visit our website at www.zcom.com.t w /rpc or you may contact us as below for support: Z-Com, Inc.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Z-Com R1 Extender c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Z-Com R1 Extender - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Z-Com R1 Extender, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Z-Com R1 Extender va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Z-Com R1 Extender, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Z-Com R1 Extender.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Z-Com R1 Extender. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Z-Com R1 Extender ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
