Manuel d'utilisation / d'entretien du produit CMS-16 du fabricant Western Telematic
Aller à la page of 68
CMS-16 Console Ma nagement Switch Firmware Version 2.00 and Higher User's Guide 5 Sterling Irvine California 92618 (949) 586-9950 Toll Free: 1-800-854-7226 Fax: (949) 583-9514 http://www.
Warnings and Cautions: No Serviceable Parts Inside; Authorized Service Personnel Only Do not attempt to repair or service this device yourself. Internal components must be serviced by authorized personnel only .
Rack Mount Installation When installing this device in an instrument rack, the following factors must be accounted for: 1. Enclosed Racks: Enclosed racks must provide adequate ventilation. Make certain that the rack is not overly crowded and note that each unit in the rack generates its own heat.
Table of Contents 1. Introduction ............................................. 1-1 2. Unit Description .......................................... 2-1 2.1. Front Panel .......................................... 2-1 2.2. Back Panel ....................
7. Operation .............................................. 7-1 7.1. Any-to-Any Mode ...................................... 7-1 7.1.1. Port Connection and Disconnection ....................... 7-1 7.1.1.1. Connecting Ports ............................
1. Introduction The CMS-16 Console Port Management Switch provides secure, in-band and/or out-of-band access to RS232 console ports and maintenance ports on UNIX servers, routers and other network equipment.
Typographic Conventions ^ (e.g. ^X ) Indicates a control character . For example, the text " ^X " (Control X) indicates the [Ctrl] key and the [X] key must be pressed simultaneously . COURIER FONT Indicates characters typed on the keyboard. For example, /E or /P 02 .
2. Unit Description 2.1. Front Panel À CLEAR: Restarts the CMS operating program without changing user-selected parameter settings or breaking port connections. Á ON: Lights when AC Power is applied. Â SET: Used to Initialize the CMS to defaults specified by the SetUp Switches.
2.2. Back Panel À Network Port: An RJ45 Ethernet port for connection to your TCP/IP network. T o communicate via network, you must first specify the IP Address, Subnet Mask, and Gateway Address as described in Section 5.5.4. Á Power Cable Receptacle  Power Switch à RS232 PORTS: For connection to console ports on target devices.
3. Getting Started This section provides a brief overview of basic CMS capabilities, and describes simple tests that can be used to determine if the unit is operating properly . 3.1. Communication Parameters The Option Switches, located on the instrument back panel, select default operating settings.
3.3. System SetUp Ports In order to ensure access to important command functions, Ports 1 and 2 are designated as System SetUp Ports; the Supervisor Mode cannot be disabled at these ports. Ports 1 and 2 will always allow password protected access to all CMS command functions, even when the unit has been reset to the default state.
3. The Port Status Screen will be displayed, followed by the "CMS>" prompt, indicating that you have successfully accessed the Command Mode. If the "CMS>" prompt is not displayed, this may indicate a communication problem. Check the following: a) Cable Connection: Check the connection between the CMS and the PC.
b) Third Party Connection: Y our resident port (e.g. Port 1) issues a /C command to create a connection between two other ports. i. T o connect Port 2 to Port 3, type / C23 [Enter] . ii. While Ports 2 and 3 are connected, Port 1 will still recognize CMS commands.
4. Hardware Installation 4.1. Connecting Power to the CMS Unit The CMS is available in both AC and DC powered versions. When connecting AC or DC power to the CMS, proceed as follows: CAUTION: This device should only be operated with the type of power source indicated on the instrument nameplate.
4.2. Configure Option Switches When the CMS is shipped from the factory , the Option Switches are configured for 9600 baud, 8 Bits-No Parity , R TS/CTS handshaking, verbose command response, and command echo ON (all switches Down). These settings are compatible with most applications.
4.2.2. Default Handshake (Sw4, Sw5) The default handshake format must match the format your control device will use when communicating with the CMS. Option Switches 4 and 5 can select R TS/CTS (hardware), XON/XOFF , Both or None. Switch Default Handshake 45 D D RTS/CTS * U D XON/XOFF D U Both U U None * = Factory Setting 4.
4.4. Connecting Devices to the CMS 1. Access the Command Mode. 2. Determine which port will be used for connection to the new device (e.g. Port 3). 3. Check Buffer: T ype /S [Enter] to display the Port Status Screen. Check the "Buffer Count" column, which lists the amount of data stored in the buffer for each port.
· Ports 5, 7, and 9 (User Ports): The Port Password “COLOCA TION1” has been assigned to these three ports. If the CMS is contacted via the Network Port or Modem Port, and this password is entered at log in, User ’ s will only be able to review status and connect to the devices attached to Ports 5, 7, and 9.
5. Configuration 5.1. Access to the CMS Command Mode When the CMS Command Mode is active, commands can be invoked to select parameters, and connect or disconnect ports. Note: Command Mode cannot be accessed from a Buffer Mode Port, Passive Mode Port, or any port that is currently connected to another CMS port.
5.2. System SetUp Ports As discussed previously in Section 3 of this User ’ s Guide, Ports 1 and 2 are designated as System SetUp Ports. Ports 1 and 2 will always permit password protected access to Supervisor Level command functions, even when the unit is reset to default parameters.
After the Supervisor Password has been defined (via the System Parameters menu), the CMS will display a password prompt whenever you attempt to access the command mode. If the correct Supervisor Password is entered, the CMS command mode then starts up in Supervisor Mode.
5.4. Defining the Site ID and Supervisor Password Before configuring individual ports, the Site ID and Supervisor Password should be defined. The Site ID is used to denote the location or name of the CMS unit, and the Supervisor Password is used to restrict access to sensitive commands.
5.5. Port Configuration 5.5.1. Configuration Conventions When responding to prompts, invoking commands, and selecting items from the port configuration menus, note the following: · T o select an item from a Port Configuration menu, key in the number and press [Enter] .
5.5.2. Port Modes The CMS offers four dif ferent port operation modes; Any-to-Any Mode, Passive Mode, Buf fer Mode, and Modem Mode. The Port Modes function as follows: · Any-to-Any Mode: Allows communication between connected ports.
The Port Configuration menu offers the following options: 1. Port Name: (Up to 16 characters, Default = undefined). 2. Password: (Up to 16 characters) Defines the Port Password for this port. Note that identical Port Passwords are generally assigned to several ports.
7. Port Mode: Defines the operation mode for this port. Note that Ports 1 and 2 cannot be configured for Passive Mode or Buffer Mode. (Default = Any-to-Any Mode). When Any-to-Any , Passive, or Buffer Mode is selected, the unit will display the DTR Output prompt (Figure 5.
8. Supervisor Mode: Permits or denies port access to Supervisor Mode. When enabled (Permit), and the valid Supervisor Password is entered, the port will be allowed to invoke Supervisor Level commands. If disabled (Deny), the port may not enter Supervisor Mode, even when the Supervisor Password is entered.
11 . Timeout Disconnect: Enables and selects the T imeout Period for this port. If enabled, and the port does not receive or transmit data for the specified T imeout Period, the port will disconnect. When the port is set for Any-to-Any Mode, Passive Mode, or Buffer Mode, the default setting for this item is “OFF”.
5.5.4. Network Port Configuration Menu In order to communicate with the CMS via network, the IP Address, Subnet Mask, and Gateway Address must first be defined using the Network Parameters Menu. If desired, this menu also allows you to implement IP Security features, which can restrict access based on the user ’ s IP Address.
The Network Parameters menu offers the following options: 1. IP Address: Defines the IP Address for the CMS unit. T ype 1 press [Enter] , and follow the instructions in the submenu. (Default = undefined). 2. Subnet Mask: Defines the Subnet Mask for the CMS unit.
13. Sequence Disconnect: Enables/Disables and configures the Resident Disconnect command. This prompt offers the option to either disable the Sequence Disconnect, select a three character format, or a one character format. (Default = Three Characters).
5.5.5. Implementing IP Security The CMS can be configured to restrict unauthorized IP addresses from T elneting to the unit. This allows the user to grant T elnet access to only a specific group of IP addresses, or block a particular IP address from gaining access.
Example 1: Deny access to all hosts except 192.1.1.5: Security Mask #1: 255.255.255.255 Mask #1 Action: Deny Security Mask #2: 192.1.1.5 Mask #2 Action: Permit Since 255 is a wild card, Mask #1 blocks all IP Addresses. Mask #2 then specifically grants access to 192.
5.6. Copying Parameters to All Ports The /CP command (Copy Port Parameters) provides a convenient means for selecting similar parameters for all CMS RS-232 ports. When the /CP command is invoked, the unit will display a menu which allows you to select port communication parameters, and then copy them to all CMS RS-232 ports.
T o select common parameters for all CMS RS-232 ports, proceed as follows: 1. Access the CMS command mode. If the password prompt is displayed, key in your Supervisor Level Password. 2. At the command prompt, type /CP and press [Enter] , the menu shown in Figure 5.
6. The Status Screens The CMS Status Screens display the connection status and communication parameters for the sixteen RS-232 ports and the Network Port. There are four different types of status screens; The Port Status Screen (/S), the Port Diagnostics Screen (/SD), the Network Status Screen (/SN), and the Port Parameters Screens (/W).
As shown in Figure 6.1, The Port Status Screen lists the following items: · Name: The user-defined name for each port. · Password: The user-defined password for each port. Note that actual passwords are not displayed; this column will read either “undefined” or “defined”.
6.2. The Port Diagnostics Screen (/SD) The Port Diagnostics Screen provides more detailed information about each port, including the port name and communication parameters. T o display the Port Diagnostics Screen, access the command mode and type /SD [Enter] , the screen will appear as shown in Figure 6.
· Baud: The baud rate selected for each port. · COM: The Data Bits, Parity , and Stop Bits selected for each port. For example, “8N1” indicates Eight data bits, No parity , and One stop bit. · HS: The handshaking (flow control) mode for each port.
6.4. The Port Parameters Screens (/W) The /W command displays more detailed information about an individual CMS port. Rather than listing connection information for all ports like the Port Status Screens, the Port Parameters screen lists all defined parameters for a specific port.
The /W command uses the following format: /W[P] xx [Enter] Where: P Is the command option to display port passwords. Note that when this option is included (e.g. /WP 5 ), the Port Parameters Screen will display the Port Password, if defined. (Supervisor Mode Only).
7. Operation 7.1. Any-to-Any Mode Any-to-Any Mode Ports can be connected to other Any-to-Any , Passive, Buffer , or Modem Mode Ports by accessing Command Mode and issuing the /C Command. All ports can be configured for the Any-to-Any Mode. Note that the Network Port is always configured for Any-to-Any Mode.
T o Connect ports, proceed as follows: 1. Access the Command Mode. If the Password Prompt is displayed, enter your Supervisor or Port Password. 2. Invoke the /C command to connect the desired ports. a) Resident Connect: T o connect your resident port to another port, type /C xx [Enter] .
7.1.1.2. Disconnecting Ports There are three different methods for disconnecting ports, the Resident Disconnect, the Third Party Disconnect, and the No Activity T imeout. Providing the T imeout feature is enabled, a No Activity T imeout will disconnect resident ports or third party ports.
3. No Activity Timeout: Providing the T imeout feature is enabled at either connected port, the No Activity T imeout can disconnect Resident Ports, or Third Party Ports. a) RS232 Ports: T o configure the Timeout Feature for the RS232 Ports, invoke the /P command to display the Port Configuration Menu for the desired port as described in Section 5.
Hunt Group port names must be unique. Otherwise, ports with similar names will also be included in the Hunt Group. Hunt Group Example 1: 1. Ports 1 and 2 are Modem Mode ports, and modems are installed at both ports. Port 1 is named "MODEM1" and Port 2 is named "MODEM2".
7.3.1. Reading Data from Buffer Mode Ports T o retrieve data from Buffer Mode Ports, you must first determine which port buffers contain data. T o check port buffers for stored data, access the Command Mode and type /S [Enter] to display the Port Status Screen.
7.4. Modem Mode In addition to allowing data transfer , the Modem Mode also provides additional functions specifically related to modem communication. A Modem Mode Port can perform all functions normally available in Any-to-Any Mode. The Modem Mode is available to all CMS ports except the Network Port.
8. Saving and Restoring Configuration Parameters After the CMS has been properly configured, parameters can be downloaded and saved as an ASCII text file. Later , if the configuration is accidentally altered, the file with the saved parameters can be uploaded to automatically reconfigure the unit without the need to manually assign each parameter .
8.2. Restoring Saved Parameters This section describes the procedure for using ProComm to send stored parameters to the CMS. 1. Start your terminal emulation program and access the CMS Command Mode; if the password prompt is displayed, enter the Supervisor Password.
9. Upgrading CMS Firmware When new , improved versions of the CMS operating firmware become available, the “Upgrade Firmware” function can be used to update the CMS unit. Updates can be uploaded via Setup Ports One and T wo, or via the Network Port.
6. Incomplete Upload: If the upload is interrupted, times-out, or if the file is corrupted during transfer , the CMS will display a screen which asks for user confirmation before proceeding. T o proceed, type 1 and press [Enter] , then return to Step 4 above.
10. Command Reference Guide 10.1. Command Conventions The commands described in this section conform to the following conventions: · Slash Character: Most CMS commands begin with the Slash Character ( / ).
10.2. Command Response When commands are sent to the CMS, the unit can respond with either verbose (English T ext) or terse messages (numeric / abbreviated). The default message type for all ports can be set to either terse or verbose using Option Switch Six.
10.3. Command Summary Command A vailability Function Command Syntax Supervisor User Exit Command Mode /X [Enter] XX Help Menu /H [Enter] XX Display Site ID /J [Enter] XX Display Port Status /S[P] [Ent.
10.4. Command Set This Section provides more detailed information on all CMS commands, sorted alphabetically by name. [Enter] Enter Command Mode In order to set parameters or connect ports, you must first access the command mode as described in Section 5.
/C Connect Establishes a bi-directional connection between two ports. For more information and command line examples, please refer to Section 7.1. There are two different types of port connections: · Resident Connect: If the /C command specifies one port name or number , your resident port will be connected to the specified port.
/D Third Party Disconnect Invoke the /D command at your resident port to disconnect two other ports. The /D command cannot be used to disconnect your resident port.
/F Set System Parameters Displays a menu which is used to define the Site ID message and Supervisor Password. When the Supervisor Password is defined, the CMS will display a password prompt before allowing access to command mode. For more information, refer to Section 5.
/N Set Network Port Parameters Displays a menu which is used to define communication parameters for the Network Port. Also allows access to the IP Security function, which can be used to restrict network access by unauthorized IP addresses. For more information on selecting network parameters, please refer to Section 5.
/SN Display Network Status Displays the Network Status Screen, which lists current conditions and parameters for the Network Port. For more information on the Network Status Screen, please refer to Section 6.3. A vailability: Supervisor Only Format: /SN[P] [Enter] When the "P" option is included (e.
/W Display Port Parameters (Who) Displays configuration of an individual port, but does not allow the user to change parameters. Ports with User Level command capability cannot display parameters for other ports. Normally , the Port Parameters screen will not include the Port Password.
A. RS232 Port Interface DCD and DTR hardware lines function as follows: 1. When connected: a) If either port is set for Modem Mode, the DTR output at either port reflects the DCD input at the other end. b) If neither port is set for Modem Mode, DTR output is held high (active).
B. Specifications RS232 Port Interface: 16 RS232 serial inputs use DB9 connectors configured as DTE ports. Network Interface: 10Base-T Ethernet, RJ45 Coding: Asynchronous, 7/8 bits ASCII. Parity: Even, Odd, None Stop Bits: 1o r2 . Data Rate: 300 to 1 15.
C. Customer Service Customer Service hours are from 8:00 AM to 5:00 PM, PST , Monday through Friday . When calling, please be prepared to give the name and make of the unit, its serial number and a description of its symptoms.
Index A Accept Break ................... 5-10, 5-13 ACTIVITY Indicator ................... 2-1 Any-to-Any Mode ........... 5-6, 5-8, 7-1 to 7-4 Application Example ................... 4-4 Asterisk Character ................... 10-1 B Back Panel Components .
H Handshake ......................... 5-7 Default ......................... 4-3 Hang-Up String ...................... 5-8 Help Screen .................... 3-3, 10-7 Hunt Groups ........................ 7-4 I Initialization ..................... 2-1, 4-3 Initialization String (Modem) .
R RDY Indicator ...................... 2-1 Reset Network Port ................... 10-9 Reset String ........................ 5-8 Resident Connect ................. 7-1 to 7-2 Resident Disconnect ............. 5-9, 7-3, 10-4 Response Message Format ...
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Western Telematic CMS-16 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Western Telematic CMS-16 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Western Telematic CMS-16, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Western Telematic CMS-16 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Western Telematic CMS-16, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Western Telematic CMS-16.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Western Telematic CMS-16. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Western Telematic CMS-16 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
