Manuel d'utilisation / d'entretien du produit Power Painter du fabricant Wagner SprayTech
Aller à la page of 19
English Owner’s Manual Read this manual for complete instructions Table of Contents Safety Information ................................................... 2 What’s in the Box .................................................... 3 Before you Begin .
This symbol indicates a hazardous situation, which, if not not avoided could result in death or serious injury. HAZARD: INJECTION INJURY A high pressure stream of paint produced by this equipment can pierce the skin and underlying tissues, leading to serious injury and possible amputation.
3 English Important Safety Information · Read all safety information before operating the equipment. SAVE THESE INSTRUCTIONS. Grounding Instructions This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.
English 4 Before You Begin Important Preparation Tips: Selecting the Proper Spray Tip: • It is important to mix the material thoroughly before you begin. Do not shake the material to mix it. Always stir the material gently but thoroughly before use.
5 English Material Container Setup 1. Remove the material container from the pump housing by turning the pump housing ring counterclockwise. 7. Twist the pump housing ring to thread the container onto the pump housing. Plug in the unit. 3. Fill the container with the material to be used.
English 6 Remote Suction Set Setup (optional) 1. Remove the material container from the pump housing by turning the pump housing ring counterclockwise. 7. Submerge the suction tube assembly into the material container and attach the container clip (l) to the side to hold it securely.
7 English Flow Control Knob / Practice Spraying 1. Turn the ow knob fully counterclockwise to maximum. 3. Turn the ow knob clockwise until you have a good spray pattern. 2. Point the sprayer at a scrap piece of wood or cardboard, and pull the trigger to prime the sprayer.
English 8 Title Usage Overspray: Priming with the Remote Suction Set: 1. If you are using the remote suction set, you will need to prime the sprayer by removing air from the system. To prime: Make sure the sprayer is plugged in, and turn the ow control knob counterclockwise to maximum.
9 English Title Spraying Technique 1. Keep your arm moving at constant speed and keep the sprayer at a constant distance from the surface. The sprayer should be triggered at the beginning of the stroke and released at the end of the stroke. 2. Keep the sprayer at right angles to the surface.
English 10 Title Using the Quick Flush Lid (latex materials only) Cleaning the material container: 1. Unplug the sprayer. Pour the remaining material back into the original container. Remove the suction tube. 4. Slide the pump housing assembly off the sprayer.
11 English Title Using the Quick Flush Lid (latex materials only) Cleaning the Remote Suction Set: You will need a garden hose to complete the steps below. If you do not have a garden hose available, or if you used oil- based materials, follow the Cleanup for Oil-Based Materials instructions on page 12-13 .
English 12 Title Cleanup - Oil-based Materials Cleaning the Material container: 1. Unplug the sprayer. Pour the remaining material back into the original container.
13 English Cleanup - Oil-based Materials Cleaning the Remote Suction Set: 1. Make sure the sprayer is unplugged. 2. Remove the suction tube from the material container and submerge into a container of the solvent appropriate to the type of material you sprayed (warm, soapy water for latex-based materials; mineral spirits for oil-based materials.
English 14 Title Cleaning the Components - Oil-based materials Reassembly - all materials 1. Turn the spray tip counterclockwise until it is removed. Pull out the atomizer valve, being careful not to lose it. 1. Slide the spring onto the front end of the piston.
15 English Maintenance Replacement Parts 1. Turn the sprayer upside-down while the material container is removed. Squeeze a small amount of standard household oil into both the intake (a) and return (b) openings on the pump housing. Atomizer valve: The atomizer valve is shaped to cause the material to spin as it comes out of the sprayer.
English 16 Troubleshooting Problem A. Motor will not run. B. Motor has a low hum and does not spray. C. Motor operates properly but does not spray. D. Material spitting or globbing. E. Excessive fogging. F. Runs and sags in paint. G. Material drips from spray tip guard.
50 Parts list • Liste de pièces • Lista de piezas (i) (a) (g) (h) (j) (p) (q) (r) (m) (b) (c) (d) (e) (f) (k) (l) (n) (o).
51 Parts list • Liste de pièces • Lista de piezas Item Article Articulo Part No. Nº de piéce Pieza No. English Description Français Description Español Descripción Quantity Quantite Cantidad.
52 Warranty • Garantie • Garantía Wagner Spray Tech Corporation 1770 Fernbrook Lane Plymouth, Minnesota 55447 Telephone 1-800-328-8251 Copyright © Wagner Spray Tech Corporation. All rights reserved, including right of reproduction in whole or in part, in any form.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Wagner SprayTech Power Painter c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Wagner SprayTech Power Painter - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Wagner SprayTech Power Painter, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Wagner SprayTech Power Painter va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Wagner SprayTech Power Painter, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Wagner SprayTech Power Painter.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Wagner SprayTech Power Painter. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Wagner SprayTech Power Painter ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
