Manuel d'utilisation / d'entretien du produit D871ST du fabricant Vivitek
Aller à la page of 72
7.
Copyright This publication, including all photographs, illustratio ns and software, is protected under international copy- right laws, with all rights reserved. Neither this man ual, nor any of the material contained herein, may be reproduced without written consent of the autho r.
DLP Projector—User’s Manual — ii — Important Safety Information Important: It is strongly recommended that you read this sect ion carefully be fore using the projector. These safety and usage instructions will ensure that you enj oy many years of safe use of the pr ojector.
Preface Projector Installation Notice Place the projector in a horizontal p osition The tilt angle of the projector should not excee d 15 degrees, nor should the proje ctor be installed in any way other than the desktop and ceiling mou nt, ot herwise lamp life could decrease dramatically.
DLP Projector—User’s Manual Power Safety Only use the supplied power cord. Do not place anything on the powe r cord. Place the power cord where it will not be in the way of foot traffic. Remove the batteries from the remote control whe n storing or not in use for a prolonged period.
Preface – v – Main Features Lightweight unit, easy to p ack away and transport. Compatible with all m ajor video stan dards including NTSC, P AL, and SECAM. A high brightness rating allows for present ations in daylight or in lit rooms.
DLP Projector—User’s Manual — vi — Table of Contents GETTING STARTED .......................................................................................................................................................... 1 P ACKING C HECKLIST .
Preface – vii – A UDIO P ROBLEMS ............................................................................................................................................................. 49 H AVING THE P ROJECTOR S ERVICED ....................
DLP Projector – User’s Manual – 1 – G ETTING S TARTED Packing Checklist Carefully unpack the projector and che ck that the following items are included: DLP P ROJECTOR WITH L ENS C AP R EMOTE .
DLP Projector—User’s Manual Views of Projector Parts Front-right View For D86 Series I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. IR receiver Receive IR signal from rem ote control 2. Lens Projection Lens 3. Focus ring Focuses the projected image 4. Zoom ring Enlarges the projected im age 19 5.
DLP Projector – User’s Manual For D87 Series I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. IR receiver Receive IR signal from rem ote control 2. Lens Projection Lens 3. Focus ring Focuses the projected image 19 4. (POWER) See Top view —Power butto ns and LEDs.
DLP Projector—User’s Manual Top view—Power buttons and LEDs I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. (POWER) Turns the projector O n or Off 14 On Lamp Error.
DLP Projector – User’s Manual Rear view Warning: As a safety precaution, disconnect all power to the projector and connecti ng devices before making connections. For D860/D861 Series I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. AC IN Connect the POWER CABLE 14 2.
DLP Projector—User’s Manual For D862/D871/D873 Series I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. AC IN Connect the POWER CABLE 14 2. S-VIDEO Connect the S-VI DEO CABL E from a vide o device 3. VIDEO IN Connect the COM POSITE CABLE from a vide o device 4.
DLP Projector – User’s Manual Bottom view I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Ceiling support ho les Contact your dealer for in formation on mounting th e projector on a ceiling 2. Tilt adjustor Rotate adju ster lever to adjust angle po sition.
DLP Projector—User’s Manual Remote Control Par ts For D860/D861 Series I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Up cursor Navigates and changes settings in the OSD 2. Enter Changes settings in the OSD 20 3. Power Turns the p rojector On or Off 14 4.
DLP Projector – User’s Manual Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow (A) . Pull out the cover (B) . 2. Insert the battery with the positive side facing up. 3.
DLP Projector—User’s Manual For D862/D871/D873 Series I TEM L ABEL D ESCRIPTION S EE PAGE : 1. IR transmitter Transmit s signals t o projector 2. Status LED Lights when th e remote control i s used 3. Laser Press to operate the on-screen pointer 4.
DLP Projector – User’s Manual – 11 – I TEM L ABEL D ESCRIPTION S EE PAGE : 12. Mute Mutes the built-in speake r 13. Zoom+ Zoom in 14. Zoom- Zoom out 15. Freeze Freeze/unfreezes the on-scree n picture 16. Blank Makes the scre en blank 17. Source Detects the input device 18.
DLP Projector—User’s Manual Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow. 2. Insert the battery with the positive side facing up. 3. Replace the cover. Caution: 1.
DLP Projector – User’s Manual – 13 – Important: 1. Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the re mote control and the proj ector.
DLP Projector—User’s Manual S ETUP AND O PERATION Starting and Shutting down t he Projec tor 1. Connect the power cord to the projector. Connect the other end to a wall outlet. The POWER LED on the projector light. 2. Turn on the connected devices.
DLP Projector – User’s Manual 4. If more than one input device is con- nected, press the SOURCE button and use ▲▼ to scroll among devices. (Component is supported through the RGB to COMPONENT ADAPTER.
DLP Projector—User’s Manual Setting an Access Password (Security L ock) You can use the four (arrow) buttons to set a password and pr event un authorized use of the projector. When enabled, the password must be entered after you p ower on the projector.
DLP Projector – User’s Manual 5. You can use the cursor buttons ▲▼◄► either on keypad or IR remote control for password entry. You can use any combination including the same arrow five times, but not less than five. Press the cursor buttons in any order to set the password.
DLP Projector—User’s Manual Adjusting the Projector Level Take note of the following when setting up the projector: The projector t able or stand should be level and sturdy . Position the projector so that it is perpendicular t o the screen.
DLP Projector – User’s Manual Adjusting the Zoom, Focus and Keystone 1. Use the Image-zoom control (on the projector only) to resize the pro- jected image and screen size (*) . 2. Use the Image-focus control (on the projector only) to sharpen the pro- jected image or .
DLP Projector—User’s Manual O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you ma ke image adjustments and c hange various settings. Navigating the OSD You can use the remote contro l cursor buttons to navigate and make changes to the OSD.
DLP Projector – User’s Manual Setting the OSD Language Set the OSD language to your pr eference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to Installation I. 2. Press the cursor ▲▼ button until Language is highlighted.
DLP Projector—User’s Manual OSD Menu Overview Use the following illustration to quickly find a se tting or determine the range for a setting. – 22 –.
DLP Projector – User’s Manual – 23 – OSD Sub-Menu Overvie w Note: (*1) Not available in D871/D873 Series. (*2) Not available in D860/D861/D862 Series.
DLP Projector—User’s Manual Image Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image Menu . Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄► to change values for settings.
DLP Projector – User’s Manual Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Advanced menu and then press Enter or ► . Press ▼▲ to move up and down in the Advanced menu.
DLP Projector—User’s Manual Color Manager Press (Enter) / ► to enter the Color Manager sub menu. I TEM D ESCRIPTIO N Red Select to enter the Red Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain. Green Select to enter the Green Col or Manager.
DLP Projector – User’s Manual Computer Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Com- puter menu. Press the cursor ▲▼ button to move up and down in the computer menu. Press ◄► to change values for settings.
DLP Projector—User’s Manual Video/Audio Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Video/Audio menu. Press the cursor ▲▼ button to move up and down in the Video/Audio menu. Press ◄► to change values for settings.
DLP Projector – User’s Manual Audio Press (Enter) / ► to enter the Audio sub menu. I TEM D ESCRIPTIO N Volume Press the ◄► butto ns to ad just the audi o volum e.
DLP Projector—User’s Manual Installation I Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installa- tion I menu. Press the cursor ▲▼ button to move up and down in the Installation I menu. Press ◄► to change values for settings.
DLP Projector – User’s Manual Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Installation I menu. Press ▲▼ to move to the Advanced menu and then press Enter or ► . Press ▲▼ to move up and down in the Advanced menu.
DLP Projector—User’s Manual Installation II Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installa- tion II menu.
DLP Projector – User’s Manual – 33 – Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Installation II menu. Press ▲▼ to move to the Advanced menu and then press Enter or ► . Press ▲▼ to move up and down in the Advanced menu.
DLP Projector—User’s Manual OSD Menu Setting I TEM D ESCRIPTIO N Menu Position Press ◄► button to select different OS D location. Translucent Menu Press ◄► butt on to select O SD backgrou nd translucent l evel. Menu Disp lay Press ◄► button to select OSD timeout delay.
DLP Projector – User’s Manual Lamp Hour Reset Please refer to Resetting the Lamp on page 44 to reset the lamp hour counter. 3D I TEM D ESCRIPTIO N 3D Press ◄► to select Off, DLP-Link or IR. 3D Sync In vert Press ◄► to turn 3D Sy nc Invert O n or Off.
DLP Projector—User’s Manual Network I TEM D ESCRIPTIO N Network State Displays the network connection status. DHCP Press ◄► to turn DHCP On or Off. Note: If you select DHCP Off, complete the IP Address, Subne t Mask, Gateway, and DNS fields. IP Address Enter a valid IP a ddress if DHCP is turned off.
DLP Projector – User’s Manual For simplicity and ease of operation, the proj ector provides diverse networking and rem ote management features. The LAN/RJ45 function of the pr ojector through a network, such as remotely manage: Power On/Off, Brightness and Contra st settings.
DLP Projector—User’s Manual 3. Right-click on Local Area Connection , and select Properties . 4. In the Properties window, select the General tab, an d select Internet Protocol (TCP/IP) . 5. Click Properties . 6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK .
DLP Projector – User’s Manual 7. Press the Menu button on the projector. 8. Select Installation II → Advanced → Network . 9. After getting into Net work , input the following: DHCP: Off IP Address: 10.10.10.10 Subnet Mask: 255.255.
DLP Projector—User’s Manual C ATEGORY I TEM I NPUT -L ENGTH IP Address 14 IP ID 3 Crestron Control Port 5 Projector Name 10 Location 10 Projector Assigned To 10 DHCP (Ena bled) (N/ A) IP Address 1.
DLP Projector – User’s Manual – 41 – Factory Reset Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the Factory Reset sub menu and press (Enter) / ► to reset all the menu items to the factory default values (expect Language and Security Lock).
DLP Projector—User’s Manual – 42 – M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified replacement part, which you can order from your local dealer.
DLP Projector – User’s Manual 2. Remove the lamp compart- ment cover. 3. Remove the three screws from the lamp module. 4. Lift the module handle up. 5. Pull firmly on the module handle to remove the lamp module. 6. Reverse steps 1 to 5 to install the new lamp module.
DLP Projector—User’s Manual Resetting the Lamp After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 1. Press the MENU button to open the OSD menu. 2. Press the cursor ◄► button to move to the Installation II menu.
DLP Projector – User’s Manual – 45 – Cleaning the Projector Cleaning the projector to remove dust and gr ime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning.
DLP Projector—User’s Manual Using the Kensingt on ® Lock & Using the Security Bar Using the Kensington ® Lock If you are concerned about security, attach the proj ector to a permanent obje ct with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensi ngton security cable.
DLP Projector – User’s Manual – 47 – T ROUBLESHOOTING Common problems and solut ions These guidelines provide tips to deal with problem s you may encounter while using the projector. If the problem remains unsolved, cont act your dealer for assistance.
DLP Projector—User’s Manual – 48 – LED Error Messages E RROR C ODE M ESSAGE S P OWER LED B LUE L AMP LED B LUE Standby mode ON OFF System Initial Flash OFF Over temperature 3 OFF Thermal break.
DLP Projector – User’s Manual – 49 – Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is secure ly connected. 2. Ensure the power source is goo d by te sting with another electrical device. 3. Restart the projector in the co rrect order and check that the Powe r LED is blue.
DLP Projector—User’s Manual – 50 – HDMI TM Q & A Q. What is the difference between a “Standard” HDMITM cable and a “High-Speed” HDMITM cable? Recently, HDMI TM Licensing, LLC announced that cables would be test ed as Standard or High-Speed cables.
DLP Projector – User’s Manual – 51 – S PECIFICATIONS Specifications Model D860 D861 D862 Display ty pe TI DMD 0.55” Resolution SVGA 800x600 XGA 1024x768 Projection distance 1 ~ 10 m Projection screen size 23” ~ 300” 25.6” ~ 308” Projection lens Manual Focus/Manual Zoom Zoom ratio 1.
DLP Projector—User’s Manual – 52 – Model D871ST D873ST Display ty pe TI DMD 0.55” Resolution XGA 1024x768 Projection distance 0.5 ~ 4 m Projection screen size 41” ~ 328” Projection lens .
DLP Projector – User’s Manual Projection Distance vs. Projection Si ze Projection Distance and Size Table D860 / D86ZA ～ ZE I MA GE D IAGONA L （ INCH ） I MA GE W IDTH ( INCH ) I MA GE H IGHT ( INCH ) P ROJECTION D ISTANCE （ MM ） F ROM P ROJECTION D ISTANCE （ MM ） TO O FFSET -A ( MM ) 60 48 36 2353.
DLP Projector—User’s Manual – 54 – D861 / D86AA ～ AE I MA GE D IAGONA L （ INCH ） I MA GE W IDTH ( INCH ) I MA GE H IGHT ( INCH ) P ROJECTION D ISTANCE （ MM ） F ROM P ROJECTION D ISTANCE （ MM ） TO O FFSET -A ( MM ) 60 48 36 1950.7 2340.
DLP Projector – User’s Manual – 55 – D871ST / D873ST / D87ASTA ～ ASTE I MA GE D IAGONA L （ INCH ） I MA GE W IDTH ( INCH ) I MA GE H IGHT ( INCH ) P ROJECTION D ISTANCE （ MM ） O FFSET -A ( MM ) 40 32 24 487.7 85.3 60 48 36 731.5 128.0 70 56 42 853.
DLP Projector—User’s Manual – 56 – Timing Mode Table S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB DVI / HDMI TM NTSC － 15.734 60.0 O － － － PAL/SECAM － 15.625 50.0 O － － － 720 x 400 37.
DLP Projector – User’s Manual – 57 – S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB DVI / HDMI TM 1600 x 1200 75.0 60.0 － － O O 640 x 480 35.0 66.68 － － O O 832 x 624 49.725 74.55 － － O O 1024 x 768 60.
DLP Projector—User’s Manual Projector Dimensions – 58 –.
DLP Projector – User’s Manual – 59 – R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply wi th the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules.
DLP Projector—User’s Manual – 60 – A PPENDIX I RS-232C Protocol RS232 Setting Baud rate: 9600 Parity check: None Data bit: 8 Stop bit: 1 Flow Con- trol None Minimum delay for next command: 1ms Control Command Stru cture P1 P2 Pin no. Name Pin no.
DLP Projector – User’s Manual – 61 – Header code Command code Data code End code HEX Command Data 0Dh ASCII ｀ V’ Command Data CR Operation Command Note: XX=00-98, projector's ID, XX=9.
DLP Projector—User’s Manual – 62 – VXXG0107 Get Gamma 0:PC 1:MAC 2:Video 3:Chart 4: B&W Pn/F VXXS0107n Set Gamma 0:PC 1:MAC 2:Video 3:Chart 4: B&W P/F Command Group 02 ASCII Function D.
DLP Projector – User’s Manual – 63 – VXXG0304 Freeze On Pn/F VXXS0304n Freeze On P/F VXXG0305 Volume n=0~8 Pn/F VXXS0305n Volume n=0~8 P/F VXXG0306 Treble n=0~16 Pn/F VXXS0306n Treble n=0~16 P.
201 1 201 107.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Vivitek D871ST c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Vivitek D871ST - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Vivitek D871ST, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Vivitek D871ST va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Vivitek D871ST, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Vivitek D871ST.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Vivitek D871ST. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Vivitek D871ST ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
