Manuel d'utilisation / d'entretien du produit D5185HD du fabricant Vivitek
Aller à la page of 76
.
Copyright This publication, including all photographs, illustratio ns and software, is protected under international copy- right laws, with all rights reserved. Neither this man ual, nor any of the material contained herein, may be reproduced without written consent of the autho r.
DLP Projector—User’s Manual — ii — Important Safety Information Important: It is strongly recommended that you read this sect ion carefully be fore using the projector. These safety and usage instructions will ensure that you enj oy many years of safe use of the pr ojector.
P P P r r r e e e f f f a a a c c c e e e – iii – Projector Installation Notice ¾ Place the projector in a horizontal p osition The tilt angle of the projector should not exceed 15 degrees , nor .
DLP Projector—User’s Manual — iv — Verify Installation Location ¾ To supply power, the 3-blade (with earth ing lead) socket should be used to ensure proper grounding and equalize d ground potential for all of the equipment in the Proje ctor System.
P P P r r r e e e f f f a a a c c c e e e – v – Choosing a Projector Edge blending application ¾ Not only brightness, bright balances, lens but st ability is important too when ch oosing a projector. ¾ A projector need 30 to 60 minutes warm up to adju st properly.
DLP Projector—User’s Manual Power Safety ¾ Only use the supplied power cord. ¾ Do not place anything on the powe r cord. Place the power cord where it will not be in the way of foot traffic. ¾ Remove the batteries from the remote control whe n storing or not in use for a prolonged period.
P P P r r r e e e f f f a a a c c c e e e – vii – Main Features • Lightweight unit, easy to p ack away and transport. • Compatible with all m ajor video stan dards including NTSC, P AL, and SECAM. • A high brightness rating allows for present ations in daylight or in lit rooms.
DLP Projector—User’s Manual — viii — Table of contents GETTING STARTED ........................................................................................................................................................... 1 P ACKING C HECKLIST .
P P P r r r e e e f f f a a a c c c e e e – ix – I MAGE P ROBLEMS .............................................................................................................................................................. 48 L AMP P ROBLEMS ...
DLP Projector – User’s Manual – 1 – G ETTING S TARTED Packing Checklist Carefully unpack the projector and che ck that the following items are included: P RO JECTO R W ITH L ENS C AP R EMOTE C.
DLP Projector—User’s Manual Views of Projector Parts Front-right View I TEM L ABEL D ESCRIP TION S EE PAGE : 1. IR receiver Receives IR si gnal from remote control 7 2. Lens Projection Lens 3. Focus ring Focuses the projected ima ge 4. Zoom ring Enlarges the projecte d image 18 5.
DLP Projector – User’s Manual Top view—On-screen Displa y (OSD) buttons and LEDs I TEM L ABEL D ESCRIPTION S EE PAGE : 1. MENU Opens and exits OSD me nus 2. z Navigates and changes settings in the OSD z Quick Menu – For Keystone 3. ENTER Enter or confirm highlighte d OSD menu item 20 4.
DLP Projector—User’s Manual Rear view 1 8 7 6 5 4 3 2 9 10 11 12 13 1 4 15 1 6 17 18 1 9 20 21 24 25 22 23 26 27 I TEM L ABEL D ESCRIP TION S EE PAGE : 1. RJ-45 Connect a LAN cable from Ethernet 2. DP Connect a DISPLAYPORT cable from a DISPLAYPORT device 3.
DLP Projector – User’s Manual – 5 – I TEM L ABEL D ESCRIP TION S EE PAGE : 14. 12V OUT Connect the 12V OUT (Screen Trigger-- For screen controller s used) 15. WIRE IR Wire remote control conn ector (connect with wire remote connector of the Remote Control set) 16.
DLP Projector—User’s Manual Bottom view I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Tilt adjustor Rotate adjuster lever to adjust angl e position. 15 2. Ceiling support holes Contact your dealer for information on m ounting the projector on a ceiling Note: When installing, ensure that you us e only UL Listed ceiling mounts.
DLP Projector – User’s Manual Remote Control Par ts Important: 1. Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the re mote control and the proj ector.
DLP Projector—User’s Manual — 8 — I TEM L ABEL D ESC RIPTION S EE PAGE : 1. Power OFF Turns the projector off 13 2. DVI Displays the DVI source selection 3. VGA Displays the VGA source selection 4. DP Displays the Display Port source selec tion 5.
DLP Projector – User’s Manual – 9 – Remote Control Operating Range The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the remote directly at the projector.
DLP Projector—User’s Manual — 10 — S ETUP AND O PERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the di- rection of the arrow. 2. Insert the battery with the positive side facing up.
DLP Projector – User’s Manual Installing or Removing the Optional Lens Caution: y Do not shake or place excessive pressure on t he projector or the lens components as the projec- tor and lens components c ontain precision parts.
DLP Projector—User’s Manual Installing the New Lens 1. Align the notches and correctly posi- tion the electrical contact pad as shown in the picture. Note: Pin of IRIS should be in the direction as shown in the picture. 2. Rotate the lens clockwise until you feel it click into place.
DLP Projector – User’s Manual Starting and Shutting down t he Projec tor 1. Remove the lens cap. 2. Securely connect the power cord and signal cable. When connected, the power led will turn red. 3. Turn on the lamp by pressing “ ” button on the rear of the projector or “ ” on the remote control.
DLP Projector—User’s Manual 4. If more than one input device is con- nected, press the SOURCE button to scroll among devices. (Component is supported through the RGB to COMPONENT ADAPTER.
DLP Projector – User’s Manual Adjusting the Projector Level Take note of the following when setting up the projector: • The projector t able or stand should be level and sturdy . • Position the projector so that it is perpendicular t o the screen.
DLP Projector—User’s Manual Adjusting Projected Image Position Using Shift The Shift feature provides a lens shift function that can be used to adjust the position of the projected image either horizontally or vertica lly within the range detailed below.
DLP Projector – User’s Manual Adjusting the horizontal image position With the lens in the center posit ion the horizontal image pos ition can be adjusted to the left or right by up to a maximum of 10% of the half image width. Note that the maximum horizontal image height ad- justment can be limited by the vertical image position.
DLP Projector—User’s Manual Adjusting the Zoom, Focus and Keystone 1. Use the Image-zoom control (on the projector only) to resize the pro- jected image and screen size. 2. Use the Image-focus control (on the projector only) to sharpen the projected image.
DLP Projector – User’s Manual Adjusting the Volume 1. Press the Volume +/- . buttons on the remote control. The volume control appears on the display. 2. Press the or but- tons on the keypad to adjust Volume +/- . 3. Press the MUTE button to turn off the volume (This feature is avail- able only on the remote).
DLP Projector—User’s Manual — 20 — O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you ma ke image adjustments and c hange various settings. Navigating the OSD You can use the remote control curs or buttons or the buttons on the top of the projector to navigate and make changes to the OSD.
DLP Projector – User’s Manual Setting the OSD Language Set the OSD language to your pr eference before continuing. 1. Press the MENU button. Press the cursor ▲▼ button to navigate to Basic Setup . 2. Press the cursor ▲▼ button until Language is highlighted.
DLP Projector—User’s Manual OSD Menu Overview Use the following illustration to quickly find a se tting or determine the range for a setting. Image Settings Image Settings>> Advanced(PC Deta.
DLP Projector – User’s Manual Image Settings Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the Image Settings menu. Press ENTER / ► button to move up and down in the Image Settings item. Press ENTER / ► button to entry item.
DLP Projector—User’s Manual Advanced Feature Press the Menu button to open the OSD menu. Press ▲▼ to move to the Image Settings menu. Press ENTER / ► button in the Advanced item. Press ENTER / ► button to entry item.Press ▲▼ to move to the Advanced item and then press ENTER or ► or ◄► to sett ing value.
DLP Projector – User’s Manual Video Adjustment I TEM D ESCRIPTION Noise Reduction Press ENTER / ► button to enter Noise Reduction submenu, Pres s the cursor ◄► button to adjust the Noise Reduction. Flesh Tone Press the cursor ▼▲ button to sele ct different Flesh Tone.
DLP Projector—User’s Manual Display Settings Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the Display Settings menu. Press ENTER / ► button to move up and down in the Display Setting s item. Press ENTER / ► button to entry item.
DLP Projector – User’s Manual Keystone Press the ENTER/ ► button to enter the Keystone sub menu. Press ◄► to change values for set- tings. V Keystone Press the cursor ◄► button to adjust.
DLP Projector—User’s Manual HSG Adjustment Press the ENTER/ ► button to enter the HSG Adjustment item. Press ▲▼ or ◄► to change values for settings. I TEM D ESCR IPTION Primary Color Press the ▲▼ buttons to set the Primary Color. Notes: There are si x colors ( R / G/ B/ C/ M/ Y) to be cus tomized.
DLP Projector – User’s Manual White Balance Press the ENTER button to enter the White Balance sub menu. I TEM D ESCRIPTIO N Red Gain Press the ◄► buttons to adjust th e Red Gain. Green Gain Press the ◄► buttons to adjust the Green Gain. Blue Gain Press the ◄► buttons to adjust the Blue Gain.
DLP Projector—User’s Manual Audio Settings Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the Audio Settings menu. Press ENTER / ► button to move up and down in the Audio Settings item. Press ENTER / ► button to entry item.
DLP Projector – User’s Manual Timer Setup Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the Timer Setup menu. Press ENTER / ► button to move up and down in the Timer Setup item. Pr ess ENTER / ► button to entry item.
DLP Projector—User’s Manual Basic Setup Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the Basic Setup menu. Press ENTER / ► button to move up and down in the Basic Setup item. Press ENTER / ► button to entry item.
DLP Projector – User’s Manual Menu Setting I TEM D ESCRIPTION Menu Position Press the cursor ▲▼ button to select a different OSD location. Menu Display Time Press the cursor ▲▼ button to select OSD timeout delay.
DLP Projector—User’s Manual Advanced Setup Press the Menu button to open the OSD menu. Press ▲▼ to move to the Advanced Setup menu Press ENTER / ► button to move up and down in the Advanced Setup item. Press ENTER / ► but- ton to entry item.
DLP Projector – User’s Manual Network Settings I TEM D ESCR IPTION Control By Press the ▲▼ buttons to select projector remote command cont rol. Selecting RJ45 enables RJ45 cont rol and disables the RS232 port. Selecting RS232 enable s RS232 control and disable s the RJ45 network p ort.
DLP Projector—User’s Manual Network Status I TEM D ESCRIPTION Network Status Displays t he network connection status. DHCP Press ▲▼ to turn DHCP On or Off. Note: If user selects ‘DHCP’ Off, it will still use user apply IP setting or default RJ45 IP setting.
DLP Projector – User’s Manual For simplicity and ease of operation, the proj ecto r provides diverse networking and rem ote management features. The LAN/RJ45 function of the pr ojector through a network, such as remotely manage: Power On/Off, Brightness and Contra st settings.
DLP Projector—User’s Manual 3. Right-click on Local Area Connection , and select Properties . 4. In the Properties window, select the General tab, an d select Internet Protocol (TCP/IP) . 5. Click Properties . 6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK .
DLP Projector – User’s Manual 7. Press the Menu button on the projector. 8. Select Advanced Setup → Net w ork Settings → Contro l By → RJ45 option. 9. After getting into Net work Status , input the following: ` DHCP: Off ` IP Address: 10.10.
DLP Projector—User’s Manual C ATEGORY I TEM I NPUT -L ENGTH IP Address 14 IP ID 3 Crestron Control Port 5 Projector Name 10 Location 10 Projector Assigned To 10 DHCP (Enabled) (N/A) IP Address 15 .
DLP Projector – User’s Manual Information Menu Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the Information Menu .. I TEM D ESCRIPTION Source Displays the activated input source. Resolution Displays the nativ e resolution of input source.
DLP Projector—User’s Manual — 42 — M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified replacement part, which you can order from your local dealer.
DLP Projector – User’s Manual 4. Unlock the lamp cover. 5. Pull up and remove the cover. 6. Use a screwdriver to re- move the screws from the lamp module.
DLP Projector—User’s Manual 8. Reverse steps 1 to 7 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage. Note: The lamp module must sit securely in place and the lamp connector must be connected properly before tightening the screws.
DLP Projector – User’s Manual – 45 – Cleaning the Projector Cleaning the projector to remove dust and gr ime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning.
DLP Projector—User’s Manual Using the Physical Lock Using the Kensington ® Lock If you are concerned about security, attach the proj ector to a permanent obje ct with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensi ngton security cable.
DLP Projector – User’s Manual – 47 – T ROUBLESHOOTING Common problems and solut ions These guidelines provide tips to deal with problem s you may encounter while using the projector. If the problem remains unsolved, cont act your dealer for assistance.
DLP Projector—User’s Manual — 48 — LED Error Messages P OWER LED T EMP LED L AMP LED E RROR C ODE M ES SAGES B LUE R ED R ED R ED Lamp Ready ON － － － Start － flashing － － Cooling .
DLP Projector – User’s Manual – 49 – Adjust the Color Temperature and Gamma settings on th e Display Settings me nu of the OSD. Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is securely connected. 2.
DLP Projector—User’s Manual — 50 — HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? Recently, HDMI Licensing, LLC announ ced that cables would be tested as Standard or High- Speed cables.
DLP Projector – User’s Manual – 51 – S PECIFICATIONS Specifications Display ty pe 1080P 0.65” Resolution 1080P 1920x1080 Native Projection distance 1.
DLP Projector—User’s Manual Projection Distance vs. Projection Si ze (1080P) V-Sync Projection Distance Image Hight Keystone Corre ction Angle A Projection Distance and Size Table Standard projection len: TR: 1.54~1.93; offset=120% T ELE W IDE Distance (m) 1.
DLP Projector – User’s Manual – 53 – Short throw projection len: TR: 0.77; offset=120% F IX Distance (m) 0.68 1.36/ 1.70 2.56 Diagonal (inch) 40 80 100 150 Keystone Correction Angle (degree) 23.
DLP Projector—User’s Manual — 54 — Timing Mode Table S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) V IDEO / S-V IDEO C OMPONENT RGB DVI HDMI / DP NTSC － 15.734 60.0 O － － － － PAL/SECAM － 15.625 50.0 O － － － － 720 x 400 37.
DLP Projector – User’s Manual – 55 – S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) V IDEO / S-V IDEO C OMPONENT RGB DVI HDMI / DP 1600 x 1200 75.0 60.0 － － O O O 1920 x 1080 67.5 60.0 － － O O O VESA 1920 x 1200 74.04 59.95 － － O O O 640 x 480 35.
DLP Projector—User’s Manual Projector Dimensions — 56 —.
DLP Projector – User’s Manual – 57 – R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply wi th the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules.
DLP Projector—User’s Manual — 58 — A PPENDIX I RS-232C Protocol RS232 Setting Baud rate: 115200 Parity check: None Data bit: 8 Stop bit: 1 Flow Control None RS-232 Setup for D 5180 / D5185 In the main HyperTerminal window, 1. Select “ Property ” from the “ File ” Menu 2.
DLP Projector – User’s Manual – 59 – Operation Command Note: XX=00-98, projector's ID, XX=99 is for all projectors D5180/D5185 -> V99Sxxxx Return Result P=Pass / F=Fail n: 0:Disable/1:.
DLP Projector—User’s Manual — 60 — Command Group 01 ASCII HEX Function Description Return Value VXXG0108n 56H 39H 39H 47H 30H 31H 30H 38H 0D H Get Picture Mode 0:Movie 1:Bright 2:Normal 3.User1 4.User2 5.User3 P/F VXXS0108n 56H 39H 39H 53H 30H 31H 30H 38H n 0DH Set Picture Mode 0:Movie 1:Bright 2:Normal 3.
DLP Projector – User’s Manual – 61 – Command Group 03 ASCII HEX Function Description Return Value VXXG0305 56H 3 9H 39H 47H 30H 33H 30H 35H 0DH Get Volume n=0~10 Pn/F VXXS0305n 56H 39H 39H 53H.
DLP Projector—User’s Manual — 62 — A PPENDIX II The D5180HD family include the following models D5I80HD D5I8ZHDA D5I8ZHDB D5I8ZHDC D5I8ZHDD D5I8ZHDE D5I8ZHDF D5I8ZHDG D5I8ZHDH D5I8ZHDI D5I8ZHD.
DLP Projector – User’s Manual – 63 – A PPENDIX III D5185HD Edge Ble nding Equipment Requirement 1. Display Units ： two D51 85HD projectors recommended to have si milar brightness levels or closed lamp hour used.
DLP Projector—User’s Manual 5. Projector Setup 2 ： Advance Setup page, entry Alignment 6. Projector Setup 3 ： Alignment Status = ON — 64 —.
DLP Projector – User’s Manual 7. Projector Setup 4 ： Enter Warp and fine tune the screen s by the Warp functions 8. Projector Setup 5 ： Enter Blending and fine tune the scre en by the Blending functions 9.
DLP Projector—User’s Manual 10. Projector Setup 7 ： cut off unnece ssary part by using the Blanking function 11. Open up a picture to verify the blending status and repeat the abov e steps if necessa ry.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Vivitek D5185HD c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Vivitek D5185HD - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Vivitek D5185HD, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Vivitek D5185HD va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Vivitek D5185HD, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Vivitek D5185HD.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Vivitek D5185HD. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Vivitek D5185HD ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
