Manuel d'utilisation / d'entretien du produit VM-1 du fabricant Victory Refrigeration
Aller à la page of 42
MERCHANDISER MODELS VM-1, VM-2 & VM-2SL INST ALLA TION, OPERA TION & SER VICE MANUAL ★ ★ ★ ★ ★ ★ ★ ★ (For “Quick Navigation”, Click On T opics or Sections Highlighted In Bl.
W arranty (Continental USA Only) The Seller warrants to the original purchaser , equipment manufactured by Seller to be free from defect s in material and workmanship for which it is responsible. The Seller's obligation under this warranty shall be limited to replacing or repairing at Seller's option, without charge, F .
RET AIN THIS MANUAL FOR FUTURE REFERENCE Machine Serial Number_______________________________ Installation Date_____________________________________ V ictory Refrigeration Service Hotline (800) 523-5008 iv NOTICE Victory (Manufacturer) reserves the right to change specifications at any time.
T ABLE OF CONTENTS Pages Section 1 - Description....................................................................................................... . ........................ 1 A. Control and Component Location.....................................
SECTION 1 DESCRIPTION Victory Merchandiser Refrigerators are Reach-In Models with full length glass swing doors on the front. There is also an optional full length sliding glass door assembly that is available for the two section model only .
A. Control and Component Location Figure 1-2 Component Location B. Component Function 1. Doors - Swing doors are reversible for one (1) section only , and have adjustable self-closing features. a. Door Size - The doors are full length. b. Door T ype - The doors are sealed glass.
2. Refrigeration System - The refrigeration system is self-contained and slides out for easy service. 3. Shelves - (Refer to Figure 1-2 and to the Parts List Section of this manual). a. Wire Shelves - Heavy-duty epoxy coated wire shelves are adjustable and can be angled downward for gravity- feed merchandising.
VM-1 S tandard Features: ● ● NSF 7 Listed for Foodservice & Prepackaged Products ● Heavy Gauge Black Powder Coated Zinc Plated S teel Exterior ● High Impact Molded ABS Interior ● Bright .
VM - 2 & VM - 2SL S tandard Features: ● ● NSF 7 Listed for Foodservice & Prepackaged Products ● Heavy Gauge Black Powder Coated Zinc Plated S teel Exterior ● High Impact Molded ABS Int.
SECTION 2 INST ALLA TION IMPORT ANT : It is highly recommended that your merchandiser refrigerator be installed by an authorized V ictory Certified Installer . A. Receiving Shipment Upon arrival, examine the exterior of the shipment packaging for any signs of rough handling.
placed into it. T o estimate the possible product load weight it is generally conceded that a safe figure is 35 pounds for each net cubic foot storage space. For example, a 47 cubic foot cabinet could hold approximately 1645 pounds of product (47 x 35 = 1645).
from the main supply to your merchandiser . It is most important that a volt age reading be made at the compressor-motor electrical connections, or as close to the compressor- motor as possible, while the merchandiser is in operation, to assure that the correct voltage required by the compressor is being supplied.
K. VM St andard Shelf Installation Instructions 9 Step 1 Step 2 Make sure plastic end caps are on the front left and right sides of the shelf before the installation process. *Note: Putting shelving in the cabinet without end caps will cause damage to the interior! T ilt shelf at an angle and insert into cabinet.
K. VM St andard Shelf Installation Instructions (continued) 10 Step 5 Lift the inside shelf peg into the locking clip. Step 6 Shelf is installed. Attention!!!! Do not force the peg into the place.
L. Assembling and Inst alling VM-2 & VM-2SL Beverage Organizer Shelf Victory organizer shelves have adjust able product dividers that allow for merchandising a variety of products without the need to purchase multiple unique fixed dividers.
L. Assembling and Inst alling VM-2 & VM-2SL Beverage Organizer Shelf (continued) Section 2- Inst allation Section 2- Inst allation Step 5 Hold the divider evenly . Grasp the divider above the back hook and gently snap the divider over the rear support rod on the shelf.
SECTION 3 OPERA TION A. T emperature Control The temperature control should be set to maintain a temperature of 38°F (3.3°C) to 40°F (4.4°C). Note: Continued use of this equipment will allow you to become familiar with its operation and functions.
SECTION 4 MAINTENANCE A. Cleaning and Proper Detergent Use Follow requirements of local health authorities. 1. Use a detergent-sanitizer or a mild detergent (neutral) or mildly alkaline (recommended for metal surfaces) followed by a sanitizing rinse solution.
1. Daily Exterior Surface Cleaning (continued) a. Dip sponge in cleaning solution, wipe down surfaces. b. Polish with clean soft cloth. Always wipe in direction of grain. Once a week a film cutting agent may be used for metal finishes to maint ain a shining surface.
4. Once Every Three Months, Condenser Maintenance Cleaning is recommended at least once every three (3) months. However , once a month is recommended when unit is located near cooking equipment which produces grease laden vapors, i.e.: fryers, grills, steam kettles, etc.
SECTION 5 SER VICE A. Servicing the Refrigeration Condensing Unit The refrigeration condensing unit is serviceable from the front and rear of the merchandiser . 1. Discontinue power to merchandiser by turning arrow on temperature control knob to “one” (1) and unplugging power cord from electrical outlet at rear of cabinet.
B. Servicing Evaporator Fan Motors and T emperature Control (continued) b. VM-2 & VM-2SL Fan Panel/Drain Pan Disconnect (continued) ● Disconnect wiring one at a time on both sides of remaining ballast assembly .
C. Servicing Evaporator Coil and/or Heat Exchanger Assembly (continued) 5. After service to evaporator coil and/or heat exchanger assembly , reverse steps for reinstallation and proper restoration of power . *Note: If fan p anel/drain pan assembly was disconnected, make sure proper reinst allation procedures were used.
D. VM-2SL Sliding Glass Door Shim Insertion Instructions If VM-2SL cabinet has gap(s) between the sliding glass door and frame, contact factory and request door roller assembly shim(s) under part number 05314501. Following are step by step guidelines that will assist in closing any gap(s).
D. VM-2SL Sliding Glass Door Shim Insertion Instructions (continued) 1. If cabinet has gap(s) between sliding glass door and frame, place shim(s) as shown on page 19. 2. Remove door(s) from the frame by grasping firmly on both ends and lifting the door(s) up towards the top frame and pulling out towards you ( Fig.
D. VM-2SL Sliding Glass Door Shim Insertion Instructions (continued) 4. T ake the roller assembly out of the door ( Fig.4 ). 5. Install necessary amount of shims over stud screws ( Fig.5 ). Examples: (1) One shim will resolve a 1/4” gap in between the door and frame; (2) T w o shims will resolve a 1/2” gap in between the door and frame.
D. VM-2SL Sliding Glass Door Shim Insertion Instructions (continued) 7. Insert nuts with 1/4” nut driver ( Fig.7 ). 8. T urn door over after roller assembly is properly inst alled. Place top of door in top rail of frame by pushing tension spring block with door .
SECTION 6 TROUBLESHOOTING 24 Section 6 - T roubleshooting Section 6 - T roubleshooting.
PROBLEM POSSIBLE CAUSE REMEDY 1. Condensing unit fails to start - no hum. 2. Condensing unit fails to start - hums, but trips on overload protector . 3. Condensing unit start s, but fails to switch off of “start” winding. 4. Condensing unit start s and runs, but short cycles on overload protector .
7. St art capacitor open or shorted blown. 8. Run capacitor open, shorted or blown. 9. Relay defective or burned out. 10. Product zone temperature too high. 1 1. Suction line frosted or sweating. 12. Liquid line frosted or sweating. 13. Noisy condensing unit.
SECTION 7 P ARTS LIST 27 Section 7 - Part s List Section 7 - Part s List.
Victory Merchandiser One Section Cabinet & Hinged Glass Door Part s 28 Section 7 - Part s List Section 7 - Part s List.
Victory Merchandiser One Section Cabinet & Hinged Glass Door Part s List (Refer to drawing on p age 28) Item Description Part Numbers Qty 1 Light Rod Reflector 04459801 1 2 Light Rod 04459701 1 3 .
Victory Merchandiser T wo Section Cabinet & Hinged Glass Door Part s 30 Section 7 - Part s List Section 7 - Part s List.
Victory Merchandiser T wo Section Cabinet & Hinged Glass Door Part s List (Refer to drawing on p age 30) Item Description Part Numbers Qty 1 Light Rod Reflector 04460301 1 2 Light Rod 04460401 1 3.
Victory Merchandiser One Section Cabinet Refrigeration Component s 32 Section 7 - Part s List Section 7 - Part s List.
Victory Merchandiser One Section Refrigerator Component s Parts List (Refer to drawing on p age 32) *Note: Electrical wiring harness components within this p arts list pertains to cabinets manufactured on o r a f t e r June 12th, 2001! For cabinets built prior to this date, consult factory .
Victory Merchandiser T wo Section Cabinet Refrigeration Component s 34 Section 7 - Part s List Section 7 - Part s List.
Victory Merchandiser T wo Section Refrigerator Component s Part s List (Refer to drawing on p age 34) *Note: Electrical wiring harness components within this p arts list pertains to cabinets manufactured on o r a f t e r June 12th, 2001! For cabinets built prior to this date, consult factory .
SECTION 8 WIRING DIAGRAM 36 Section 8 - Wiring Diagram Section 8 - Wiring Diagram.
VM-1, VM-2 & VM-2SL (Self-Cont ained) 1 15v/60Hz/1ph Section 8 - Wiring Diagram Section 8 - Wiring Diagram “End Of Section, Click Here For T able Of Conten t s”.
VICT OR Y REFRIGERA TION 1 10 Woodcrest Road Cherry Hill, NJ 08003 Phone (856) 428-4200 Fax (856) 428-7299 W ebsite: ww w .victory-refrig.com E-Mail: p ar t s@victory-refrig.com p ar t s.order-entry@victory-refrig.com or service@victory-refrig.com Manual Part Number: 50843901 Rev: 02 Print Date: 08/13/01 Price: $15.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Victory Refrigeration VM-1 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Victory Refrigeration VM-1 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Victory Refrigeration VM-1, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Victory Refrigeration VM-1 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Victory Refrigeration VM-1, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Victory Refrigeration VM-1.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Victory Refrigeration VM-1. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Victory Refrigeration VM-1 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.