Manuel d'utilisation / d'entretien du produit K7VT4-8X du fabricant Verbatim
Aller à la page of 30
1 K7VT4-4X K7VT4-8X User M a nual V ersion 3.1 Published July 2003 Copyright©2003 ASRock INC. All rights re served..
2 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
3 Contents 1 Introduction .................................................... 4 1.1 Pa ckage Contents ........................................................... 4 1.2 Specifications ................................................................. 5 1.
4 Chapter 1 Introduction Tha n k you f or purcha sing ASRock K7VT4-4X / K7VT4-8X motherboard, a reli ab le motherboard produced under ASRock’s con sistently stringent quality control. It delivers excellent perf orma nce with robust design conf orm ing to ASRock’s com- mitment to quality and endurance.
5 1.2 Specifications Platform: A TX f orm f a ctor (12.0" x 7.0", 30.5 x 17.8 cm) CPU: Supports Socket A (462 pins ) f o r AMD Athlon TM / Athlon TM X P / Duron TM p rocessor Chipsets: North.
6 CAUTION! 1. While CPU overheat is detected, the system will automatically shut- down. Plea se chec k i f the CPU fa n on the motherboard functions prop erly bef ore you re sume the system. T o i mprove he at dissi pation, r e m ember to spray thermal gre a se between the CPU a nd the heatsink when you install the PC system.
7 17.8cm (7.0 in) 1 0 DDR 1 (64/72 bit, 184-pin module) 3 2 DDR2 (64/72 bit, 184-pin module) 5 PCI 2 PCI 3 PCI 4 PCI 5 PCI 1 21 AGP1 9 USB45 1 16 SPEAKER1 1 15 HDLED RST PLED PWRBTN 1 PANEL 1 IR1 1 2MB BIOS 20 FLOPPY1 Super I/O AUDIO1 1 JR1 JL1 CLRCMOS1 CLRCMOS2 VIA VT8235 CPU_FAN1 CHA_FAN1 CMOS Battery PS2_USB_PWR1 1 IDE1 IDE2 USB2.
8 17.8cm (7.0 in) 1 0 DDR 1 (64/72 bit, 184-pin module) 3 2 DDR2 (64/72 bit, 184-pin module) 5 PCI 2 PCI 3 PCI 4 PCI 5 PCI 1 21 AGP1 9 USB45 1 16 SPEAKER1 1 15 HDLED RST PLED PWRBTN 1 PANEL 1 IR1 1 2MB BIOS 20 FLOPPY1 Super I/O AUDIO1 1 JR1 JL1 CLRCMOS1 CLRCMOS2 VIA VT8235 CPU_FAN1 CHA_FAN1 CMOS Battery PS2_USB_PWR1 1 IDE1 IDE2 USB2.
9 1.5 ASRock I/O TM (K7VT4-4X / K7VT4-8X) 1 Parallel port 2 RJ-45 port 3 Game port 4 Microphone (Pink) 5 Line In (Light Blue) 6 Line Out (Lime) 7 USB 2.
10 Chapter 2 Installation K7VT4-4X / K7VT4-8X is a n A TX f o rm fa ctor (12.0" x 7.0", 30.5 x 17.8 cm) motherboard. Bef ore you in stall the motherboard, ple ase st udy the conf iguration of your cha ssis to ensure that the m otherboard fits into it.
11 2.3 CPU Installation Step 1. U nlock the socket by lifting the lever up to a 90 o a ngle. Step 2. Position the CPU directly above the socket such that its marked corner matche s the ba se of the socket lever . Step 3. Carefully in sert the CPU into the socket until it fits in pla ce.
12 2.5 Installation of Memory Modules (DIMM) K7VT4-4X / K7VT4-8X motherboard provides two 184-pin DD R (Double Dat a Rat e) DIMM slots. Pl e ase ma ke sure to disconnect power supply bef ore a dd in g o r removing D IMMs or the syste m components. Step 1.
13 2.7 Jumpers Setup The illustration shows how jumpers are setup. When the jumper ca p is pla ced on pins, the jumper is “SHORT”. If no jumper ca p is pla ced on the pins, the jumper is “OPEN”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “SHORT” when jumper ca p is pla ced on these 2 pin s.
14 FID Jumpers (FID0, FID1, FID2, FID3, FID4) (see p.7/p.8 item 29) Not e: The set of FID jumpers are only for advanced users to adjust the multiplier of CPU. Plea se follow the ta ble below to adjust the multi plier of CPU. However, the syste m will work well without the adjustment of multi plier .
15 Clear CMOS CLRCMOS1 CLRCMOS2 (see p.7/p.8 item 19) (see p.7/p.8 item 18) Note: CL RCMOS1 and CLRCMOS2 allow you to clear the data in CMOS. The data in CMOS includes syste m set up information such a s system pa ssword, date, ti me, a nd syste m setup para meters.
16 2.8 Connectors Conne cto rs ar e NO T j umpers. DO N OT pl a ce jumper ca ps over these connectors. Connector Figure Description F DD connector (33-pin FLOPPY1) (see p.7/p.8 item 13) Note: Match the red marking on the floppy ribbon cable with Pin1.
17 Front panel audio connector This is a n interfa ce f or the front (9-pin AUDIO1) panel audio cable that allows (see p.7/p.8 item 24) con venient connection and control of audio devices. System panel connect or This conne ctor a ccommo- (9-pin P ANEL1) dates several system front (see p.
18 Chapter 3 BIOS Setup 3.1 BIOS Setup Utility This section explains how to use the BIOS Setup Utility to configure your system. The Fla sh Me mory on the m otherboard store s the BIOS Setup Utility . Y ou ma y run the BIOS Setup when you start up the computer .
19 Navigation Key(s) Function Description <F1> Displays the General Help Screen <ESC> Jumps to the Exit menu or returns to the upper menu from the current menu / Moves cursor up or down be.
20 AMIBIOS SETUP UTILITY - VERSION 3.31a Main T ype Cylinders Heads Write Precompensation Sectors Maximum Capacity LBA Mode Block Mode Fast Programmed I/O Modes 32 Bit Transfer Mode Ultra DMA Mode [ S.
21 [CD/D V D]: This is used f or IDE CD/D V D d riv es. [ARMD]: This is used f or IDE ARMD (A T API Remo v a ble Media Device), such a s MO. Cylinders This is used to configure the number of cylinders. Refer to the drive documentation to determine the correct value.
22 Chapter 4 Software Suppor t 4.1 Install Operating System This motherboard supports various Microsoft ® Windows ® operating systems: 98 SE / ME / 2000 / XP. Because motherboard settings and hardware options vary, use the setup procedures in this cha pter for general reference only .
23 Appendix: Advanced BIOS Setup This section will introduce you the following BIOS Setup menus: “Advanced,” “Security,” “Power,” “Boot,” and “Exit.” 1. Advanced BIOS Setup Menu Spread Spectrum: This field should always be [Disabled] for better system stability.
24 Chipset Configuration: AGP Mode: If K7VT4-4X motherboard is installed for your PC system, you may selec t [ 4X ], [2X ], or [1 X] a s the A GP mode. But when a n 8X-AGP- card is installed on K7VT4-8X motherboard for your PC system, this feature will be set to [Auto] automatically.
25 Resource Configuration: PCI Latency Timer (PCI Clocks): The default is 32. It is recommended to keep the default value unless the installed PCI expansion cards’ specifications require other settings. Pr imary Gra phics Ad a pte r: Selec t PC I o r A GP a s the primary gra phics ada pter .
26 OnBoard F DC: Use this to ena ble or disa ble floppy drive controller . OnBoard Serial Port: Use this to set addresses for the onboard serial ports or disable serial ports. Configuration options: [Auto], [Disabled], [3F8 / IRQ4 / COM1], [2F8 / IRQ3 / COM2], [3E8 / IRQ4 / COM3], [2E8 / IRQ3 / COM4].
27 2. Security Setup Menu Supervisor Pa ssword: This fiel d shows the status of the Supervisor Pa ssword. [Cle ar]: No pa ssword ha s been set. [Set]: Supervisor pa ssword ha s been set. User Pa ssword: Th is f ield shows the status of the User Pa ssword.
28 3. Power Setup Menu Suspend to RAM: This field allows you to select whether to auto-detect or disable the Suspend-to-RAM feature. Select [Auto] will enable this feature if the system supports it. Repost Video on STR Resume: This feature allows you to repost video on STR resume.
29 4. Boot Setup Menu Quick Boot Mode: Enable this mode will speed up the boot-up routine by skipping memory retestings. Boot Up Num-Lock: If thi s is en a bled, it will automatically a ctivate the Numeric Lock function after boot-up. Boot T o OS/2: This en ab les boot-up to OS/2 operating syste m .
30 AMIBIOS SETUP UTILITY - VERSION 3.31a Main Advanced Security Power Boot Exit Exit Saving Changes Exit Discarding Changes Load Default Settings Discard Changes [ Setup Help ] Exits and saves the c h a n g e si nC M O SR A M .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Verbatim K7VT4-8X c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Verbatim K7VT4-8X - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Verbatim K7VT4-8X, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Verbatim K7VT4-8X va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Verbatim K7VT4-8X, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Verbatim K7VT4-8X.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Verbatim K7VT4-8X. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Verbatim K7VT4-8X ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
