Manuel d'utilisation / d'entretien du produit Corsa (2013) du fabricant Vauxhall
Aller à la page of 227
0 - 1 Owner’s Manual Model Year 2013.5 Edition: J anuary 2013 TS 1651-B-13 VAUXHALL Corsa Owner’s Manual Model Year 2013.5 Edition: January 2013 TS 1651-B-13.
Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 19 Seats, restraints ........................... 34 Storage ........................................ 51 Instruments and controls .
2 Introduction Introduction.
Introduction 3 Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available under the sections "Service and Maintenance" and "Technical data" as well as on the identification plate.
4 Introduction Danger, Warnings and Cautions 9 Danger Text marked 9 Danger provides information on risk of fatal injury. Disregarding this information may endanger life. 9 Warning Text marked 9 Warning provides information on risk of accident or injury.
Introduction 5.
6 In brief In brief Initial drive information Vehicle unlocking Turn the key in the driver's door lock to the front or press button q to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, pull the button under the tailgate moulding.
In brief 7 Seat backrests Turn handwheel. Do not lean on seat when adjusting. Seat adjustment 3 36, Seat position 3 35, Folding front passenger seat backrest 3 37. Seat height Lever pumping motion up = higher down = lower Seats 3 36, Seat position 3 35.
8 In brief Seat belt Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °). To release belt, press red button on belt buckle.
In brief 9 Setting with four-way switch in vehicles with electronic window operation First select the relevant exterior mirror then use the control to adjust. Electric adjustment 3 27, Convex exterior mirrors 3 27, Folding exterior mirrors 3 27, Heated exterior mirrors 3 28.
10 In brief Instrument panel overview.
In brief 11 1 Side air vents ...................... 109 2 Light switch .......................... 95 Instrument illumination ....... 100 Rear fog light ......................... 99 Front fog lights ..................... 99 Headlight range adjustment .
12 In brief Exterior lighting Turn light switch AUTO = Automatic light control: Exterior lighting is switched on and off automatically m = Activation or deactivation of the automatic light control 8 = sidelights 9 = low beam Press switch > = Front fog lights r = Rear fog light Lighting 3 95.
In brief 13 Turn and lane-change signals right = lever up left = lever down Turn and lane-change signals 3 98, Parking lights 3 99. Hazard warning flashers Operated with the ¨ button.
14 In brief Washer and wiper systems Windscreen wiper & = fast % = slow $ = timed interval wipe or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down. Windscreen wiper 3 70, Wiper blade replacement 3 149.
In brief 15 Climate control Heated rear window, heated exterior mirrors Heating is operated by pressing the Ü button. Heated rear window 3 31. Demisting and defrosting the windows Air distribution to l . Set temperature control to warmest level. Set fan speed to highest level.
16 In brief Manual transmission automated N = neutral position o = drive position + = higher gear - = lower gear A = switch between automatic and manual mode R = reverse gear (with selector lever lock) Manual transmission automated 3 121.
In brief 17 Starting the engine ■ Turn key to position 1 ■ move the steering wheel slightly to release the steering wheel lock ■ operate clutch and brake.
18 In brief Parking ■ Always apply the parking brake without pressing the release button. Apply as firmly as possible on a downhill slope or uphill slope. Depress the foot brake at the same time to reduce operating force. ■ Switch off the engine. Turn the ignition key to position 0 and remove it.
Keys, doors and windows 19 Keys, doors and windows Keys, locks ................................... 19 Doors ........................................... 24 Vehicle security ............................ 25 Exterior mirrors ............................ 27 Interior mirrors .
20 Keys, doors and windows Radio remote control Used to operate: ■ Central locking system, ■ Anti-theft locking system, ■ Anti-theft alarm system, ■ Power windows. The radio remote control has a range of approx. 5 metres. This range can be affected by outside influences.
Keys, doors and windows 21 Extend the key and open the unit. Replace the battery (battery type CR 2032), paying attention to the installation position. Close the unit and synchronise. Key with fixed key section Have the battery replaced by a workshop.
22 Keys, doors and windows Central locking system with radio remote control Press button q . Two settings are possible: ■ To unlock only the driver's door: Press button q once. To unlock the entire vehicle: Press button q twice. ■ To unlock the entire vehicle: Press button q once.
Keys, doors and windows 23 Central locking button Press button m : the doors are locked or unlocked. The LED in the button m illuminates for approx. 2 minutes after locking with the radio remote control. If the doors are locked from the inside whilst driving, the LED remains illuminated.
24 Keys, doors and windows Insert the key into the opening above the lock on the inside of the door and operate the lock by lifting until it clicks. Then close the door. The procedure must be carried out for each door. The driver's door can also be locked from the outside with the key.
Keys, doors and windows 25 Note The installation of certain heavy accessories onto the tailgate may affect its ability to remain open. Closing Use the interior handle. Do not press the button under the moulding while closing as this will unlock the tailgate again.
26 Keys, doors and windows Light-emitting diode (LED) During the first 10 seconds of anti- theft alarm system activation: LED illuminates = Test, ignition delay, LED flashes quickly = Door, load compartment or bonnet open, or system fault. After the first 10 seconds of anti-theft alarm system activation: LED flashes slowly = System active.
Keys, doors and windows 27 Exterior mirrors Convex shape The convex exterior mirror contains an aspherical area and reduces blind spots. The shape of the mirror makes objects appear smaller, which will affect the ability to estimate distances.
28 Keys, doors and windows Corsa VXR: For pedestrians safety, the exterior mirrors of the Corsa VXR are released from the holder if they are struck with sufficient force. Fit mirror housing to holder with latching lugs and engage by striking gently. Manual The exterior mirrors can be folded in by pressing gently on the outer edge of the housing.
Keys, doors and windows 29 Interior mirrors Manual anti-dazzle To reduce dazzle, adjust the lever on the underside of the mirror housing. Automatic anti-dazzle Dazzle from following vehicles at night is automatically reduced. Windows Windscreen Heat-reflecting windscreen The heat-reflecting windscreen has a coating which reflects solar radiation.
30 Keys, doors and windows Windscreen stickers Do not attach stickers such as toll road stickers or similar on the windscreen in the area of the interior mirror. Otherwise the detection zone of the sensor and the view area of the camera in the mirror housing could be restricted.
Keys, doors and windows 31 Operating windows from outside Depending on the equipment level, the windows can be operated remotely from outside the vehicle. Press q or p until all windows have opened or closed. Overload If the windows are repeatedly operated at short intervals, the window operation is disabled for some time.
32 Keys, doors and windows If the sun visors have integral mirrors, the mirror covers should be closed when driving. Roof Sunroof 9 Warning Take care when operating the sunroof. Risk of injury, particularly to children. Keep a close watch on the movable parts when operating them.
Keys, doors and windows 33 Caution When using a roof rack, check the free movement of the sunroof in order to avoid damage. It is only permitted to raise the sunroof. Note If the top of the roof is wet, tilt sunroof, allow water to run off and then open sunroof.
34 Seats, restraints Seats, restraints Head restraints ............................ 34 Front seats ................................... 35 Seat belts ..................................... 38 Airbag system .............................. 41 Child restraints .
Seats, restraints 35 Head restraints on rear seats The height of the head restraints can be set in two positions. To set to the first position, pull the head restraint upwards. To set to the second position press the spring marked in the illustration and push the head restraint right up to the top.
36 Seats, restraints ■ Sit with shoulders as far back against the backrest as possible. Set the backrest to an angle so that it is possible to reach the steering wheel with arms slightly bent. Maintain contact between shoulders and the backrest when turning the steering wheel.
Seats, restraints 37 Seat height Lever pumping motion up = higher down = lower Seat folding Lift release lever and tilt backrest forwards. Lower release lever and backrest engages in lowered position.
38 Seats, restraints Heating Activate heating by pressing ß button for the seat with the ignition on. LED in button ß on: relevant front seat heating on.
Seats, restraints 39 Belt tensioners In the event of a head-on or rear-end collision of a certain severity, the front seat belts are tightened. 9 Warning Incorrect handling (e.g. removal or fitting of belts) can trigger the belt tensioners with risk of injury.
40 Seats, restraints 9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing. Height adjustment 1. Pull belt out slightly. 2. Press button. 3. Adjust height and engage audibly. Adjust the height so that the belt lies across the shoulder.
Seats, restraints 41 Airbag system The airbag system consists of a number of individual systems. When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. 9 Warning If handled improperly the airbag systems can be triggered in an explosive manner.
42 Seats, restraints The forward movement of the front seat occupants is decelerated, thereby considerably reducing the risk of injury to the upper body and head. 9 Warning Optimum protection is only provided when the seat is in the proper position. Seat position 3 35.
Seats, restraints 43 Curtain airbag system The curtain airbag system consists of an airbag in the roof frame on each side. This can be identified by the word AIRBAG on the roof pillars. The curtain airbag system is triggered in the event of an accident of a certain severity.
44 Seats, restraints Control indicator W and LEDs in the button not on: Airbag systems for the front passenger are active. No child restraint systems can be installed. Control indicator W and LEDs in button on: Front passenger airbags are deactivated and will not inflate in the event of a collision.
Seats, restraints 45 Control indicator for airbag deactivation 3 78. Note Starting the engine terminates changing of the setting. The setting can then only be changed once the ignition has been switched off and back on again.
46 Seats, restraints Allow children to enter and exit the vehicle only on the side facing away from the traffic. When the child restraint system is not in use, secure the seat with a seat belt or remove it from the vehicle. Note Do not stick anything on the child restraint systems and do not cover them with any other materials.
Seats, restraints 47 Child restraint installation locations Permissible options for fitting a child restraint system Weight and age class On front passenger seat On rear outboard seats On rear centre seat activated airbag deactivated airbag Group 0: up to 10 kg or approx.
48 Seats, restraints Permissible options for fitting an ISOFIX child restraint system Weight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat Group 0: up to .
Seats, restraints 49 ISOFIX size class and seat device A – ISO/F3 = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. B – ISO/F2 = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
50 Seats, restraints Isofix child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the mounting brackets. When using ISOFIX mounting brackets for seat mounting, universally approved child restraint systems for ISOFIX may be used.
Storage 51 Storage Storage compartments ................ 51 Load compartment ....................... 61 Roof rack system ......................... 65 Loading information ..................... 66 Storage compartments 9 Warning Do not store heavy or sharp objects in the storage compartments.
52 Storage Underseat storage Lift at recessed edge and pull out. Maximum load: 1.5 kg. To close, push in and engage. Rear carrier system The rear carrier system (Flex-Fix system) allows bicycles to be attached to a pull-out carrier integrated into the vehicle floor.
Storage 53 Pull release lever up. The system disengages and travels quickly out of the bumper. Completely pull out the rear carrier system until you hear it engage. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again.
54 Storage Push the clamping lever down and push the lamp support into the retainer until it engages. Perform this procedure for both tail lamps. Check the cable and lamp position to make sure these are correctly installed and are securely located.
Storage 55 Remove the pedal crank mounts from the pedal crank recesses. Adapting the rear carrier system to a bicycle Press the release lever and withdraw the wheel recesses.
56 Storage Prepare the bicycle for attachment Note The maximum width for the pedal crank is 38.3 mm and the maximum depth is 14.4 mm. Rotate the left pedal (without a chain cog) vertically downwards. The pedal on the left pedal crank must be horizontal.
Storage 57 Put on the bicycle. The pedal crank here must be placed in the pedal crank recess opening as shown in the illustration. Caution Make sure that the pedal does not touch the surface of the rear end carrier. Otherwise the crankset might be damaged during the transport.
58 Storage the wheel recesses and the rotary lever on the pedal crank recess until the bicycles no longer touch one another. Make sure there is sufficient clearance from the vehicle. Tighten the attachment screw for the pedal bearing mount to its maximum point by hand.
Storage 59 Retracting the rear carrier system Push the pedal crank mounts into the pedal crank recess as shown in the illustration. Insert the strap retainer and pull tightly downwards as far as possible. Press release lever and slide in wheel recesses all the way as far as they will go.
60 Storage Swivel first the right clamping lever ( 1 ) forwards, followed by the left clamping lever ( 2 ), until they can be engaged in their respective recesses. Push the clamping lever down and pull both lamp supports out of the recesses. Fold in the lamp supports on the backs of the tail lamps.
Storage 61 Load compartment Load compartment extension The rear backrest, in a single unit or split, can be locked in an upright position for transporting bulky items. Pull the release handle, pull the backrest forwards to the vertical position and engage.
62 Storage Move rear seat backrests upright and allow locking mechanisms to engage audibly at both sides. Once the backrests are locked the red mark must no longer protrude. The rear seat backrests can be locked in two positions. Do not trap the seat belt when moving the backrest to the upright position.
Storage 63 3-door passenger vehicle Lift the cover backwards until it unlatches, set at an angle, then remove. Fit in reverse order. Stowing When the load compartment is fully loaded, stow the load compartment cover behind the rear seat backrests: Lift the cover backwards until it unlatches, then slide down in guides behind the seat backrests.
64 Storage Rear floor storage cover The double load-bay floor can be inserted in the load compartment in two positions: ■ directly beneath the cover for the spare wheel recess or the floor cover, ■ or in the upper openings in the load compartment.
Storage 65 Warning triangle Store warning triangle in rear load compartment wall: first fit warning triangle into recess on left and then insert in guide on right. To remove the warning triangle, lift to the right and pull out to the right. First aid kit Stow the first-aid kit (cushion) in the compartment in the left wall of the load compartment.
66 Storage Fitting on model with sun roof Disengage covers concealing roof rack mounts by pushing sliders in direction of arrow (e.g. with coin) and remove upwards. To close roof rack mounts, first insert covers at front and engage sliders at rear. Attach roof rack at appropriate points, see enclosed roof rack system instructions.
Storage 67 around inside the vehicle and cause personal injury or damage to the load or car. ■ The payload is the difference between the permitted gross vehicle weight (see identification plate 3 190) and the EC kerb weight. To calculate the payload weight, enter the data for your vehicle in the Weights table at the front of this manual.
68 Instruments and controls Instruments and controls Controls ....................................... 68 Warning lights, gauges and indicators ..................................... 74 Information displays ..................... 83 Vehicle messages ....
Instruments and controls 69 Heated steering wheel Activate heating in combination with the seat heating by pressing ß * button once or several times with the ignition on. LED ß on: driver seat heating on. LED ß and * on: driver seat heating and steering wheel heating on.
70 Instruments and controls Windscreen wiper/washer Windscreen wiper The lever always springs back to its original position. & = fast % = slow $ = interval wiping § = off For a single wipe when the windscreen wiper is off, press the lever down.
Instruments and controls 71 Keep the sensor free from dust, dirt and ice. Windscreen washer Pull lever. Washer fluid is sprayed onto the windscreen and the wiper wipes a few times. Rear window wiper/washer Push lever forwards. The rear window wiper wipes in interval mode.
72 Instruments and controls icy road conditions. : remains illuminated until the temperature reaches at least 5 °C. In vehicles with Graphic-Info-Display or Colour-Info-Display, a warning message appears in the display as a warning for icy road conditions.
Instruments and controls 73 Power outlets The power outlet is located in the centre console. Caution Do not damage the outlet by using unsuitable plugs. Connecting electrical accessories while the engine is off will discharge the battery. Do not exceed the maximum power consumption of 120 Watts.
74 Instruments and controls The portable ashtray can be placed in the cupholders. Open cover to use. Warning lights, gauges and indicators Instrument cluster In some versions, the needles of the instruments briefly rotate to the end position when the ignition is switched on.
Instruments and controls 75 Trip odometer The top line displays the recorded distance since the last reset. To reset, hold the reset knob depressed for a few seconds with the ignition on. Tachometer Displays the engine speed. Drive in a low engine speed range for each gear as much as possible.
76 Instruments and controls 1 off = petrol operation 1 illuminates = liquid gas operation 1 flashes = no switching is possible, one type of fuel is empty As soon as the liquid gas tanks are empty, petrol operation is automatically engaged until the ignition is switched off.
Instruments and controls 77 Control indicators in the instrument.
78 Instruments and controls Turn signal O illuminates or flashes green. Illuminates The control indicator illuminates briefly when the parking lights are switched on. Flashes The control indicator flashes if a turn signal or the hazard warning flashers are activated.
Instruments and controls 79 Illuminates when the engine is running Stop, switch off engine. Battery is not charging. Engine cooling may be interrupted. In diesel engines, power to the brake servo unit may be cut. Seek the assistance of a workshop. Flashes during or after engine start Battery voltage too low.
80 Instruments and controls On vehicles with manual transmission automated, R flashes for a few seconds when the ignition is switched off if the parking brake is not applied. On vehicles with manual transmission automated, R flashes when the driver's door is opened if no gear is engaged and the parking brake is not applied.
Instruments and controls 81 Illuminates for a few seconds when the ignition is switched on. Flashing during driving The system is actively engaged. Engine output may be reduced and the vehicle may be braked automatically to a small degree 3 127. Illuminates while driving The system is switched off or a fault is present.
82 Instruments and controls Illuminates when the engine is running Caution Engine lubrication may be interrupted. This may result in damage to the engine and/or locking of the drive wheels. 1. Depress clutch. 2. Select neutral gear, set selector lever to N .
Instruments and controls 83 Adaptive forward lighting B illuminates yellow. Illuminates when the engine is running Fault in system. Seek the assistance of a workshop. Illuminates after ignition is switched on Control indicator B illuminates for approx.
84 Instruments and controls Graphic-Info-Display, Colour-Info-Display Displays time, outside temperature, date or Infotainment system (when it is on) and electronic climate control system.
Instruments and controls 85 Function areas For each function area there is a main page (Main), which is selected at the top edge of the display (only with trip computer and Mobile Phone Portal): ■ Audio, ■ Telephone, ■ Trip computer. System settings Press the Settings button on the Infotainment system.
86 Instruments and controls Some transmitters do not send a correct time signal. In such cases, we recommend to switch off automatic time synchronisation. The function is activated by highlighting the field in front of Synchron. clock automatical. in the Time, Date menu.
Instruments and controls 87 Adjusting contrast ( Graphic-Info-Display) Select menu item Contrast from the Settings menu. Confirm the required setting. Setting display mode Display brightness is dependent on vehicle lighting. Additional settings can be made as follows: Select menu item Day / Night from the Settings menu.
88 Instruments and controls engine is running, a gear is engaged and the foot brake is not depressed. ■ Warning signal sounds three times if the rear carrier system is extended and reverse gear is selected. When the vehicle is parked and the driver's door is opened ■ When the key is in the ignition switch.
Instruments and controls 89 Trip computer The trip computer provides information on driving data, which is continually recorded and evaluated electronically.
90 Instruments and controls Average consumption Display of average consumption. The measurement can be reset at any time. Stop watch Measurement of the time from activation to deactivation.
Instruments and controls 91 When the fuel level in the tank is low, the message Range appears in the display. When the fuel tank is nearly empty, the message Please refuel! appears in the display. Instantaneous consumption Displays the instantaneous consumption.
92 Instruments and controls The information of the two trip computers can be reset separately, making it possible to evaluate data from different time periods. Select the required trip computer information and confirm. To reset all information of a trip computer, select menu item All values .
Instruments and controls 93 Driving Time incl. Stops The time the vehicle is in motion is recorded. The time the vehicle is stationary with the ignition switched on is included. Travel Time Measurement of the time from manual activation via Start to manual deactivation via Reset .
94 Instruments and controls ■ Push the turn signal stalk (left) up or down and select the desired function P1 - P7 . ■ Push the wiper stalk (right) up or down and select status On or OFF , or input a value for speed ( P6 ) or value for volume ( P7 ).
Lighting 95 Lighting Exterior lighting ............................ 95 Interior lighting ........................... 100 Lighting features ........................ 102 Exterior lighting Light switch Turn light switch: AUTO = Automatic light control: Exterior lighting is switched on and off automatically depending on external lighting conditions.
96 Lighting Automatic light control function When the automatic light control function is switched on and the engine is running, the system switches between daytime running light and low beam depending on external lighting conditions. Daytime running light Daytime running light increases visibility of the vehicle during daylight.
Lighting 97 Headlights when driving abroad The asymmetrical headlight beam extends visibility at the edge of the road at the passenger side. However, when driving in countries where traffic drives on the opposite side of the road, adjust the headlights to prevent dazzling of oncoming traffic.
98 Lighting Hazard warning flashers Operated with the ¨ button. The hazard warning flashers activate automatically if the airbags deploy. Turn and lane-change signals Lever up = right turn signal Lever down = left turn signal The lever always springs back to its original position.
Lighting 99 Front fog lights Operated with the > button. Light switch in position AUTO : switching on front fog lights will switch the low beam on automatically. Rear fog lights Operated with the r button. Light switch in position AUTO : switching on front fog lights will switch the low beam on automatically.
100 Lighting Reversing lights The reversing lights come on when the ignition is on and reverse gear is selected. Misted light covers The inside of the light covers may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing.
Lighting 101 Front courtesy light with reading lights Operated with the c button when the doors are closed. Rear courtesy lights Operated with switch. I = On 0 = Off centre = automatic Load compartment lighting The lighting switches on when the load compartment is opened.
102 Lighting Lighting features Centre console lighting Spotlight in interior mirror housing. Daylight-dependent, automatically regulated centre console lighting. Entry lighting After unlocking the vehicle, the instrument panel lighting, the front and rear foot well lighting and the information display come on for a few seconds.
Climate control 103 Climate control Climate control systems ............. 103 Air vents ..................................... 109 Maintenance .............................. 110 Climate control systems Heating and ventilation system Controls for: ■ Temperature ■ Fan speed ■ Air distribution Heated rear window Ü 3 31.
104 Climate control ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J . Note If the settings for demisting and defrosting are selected, an Autostop will be inhibited.
Climate control 105 9 Warning The exchange of fresh air is reduced in air recirculation mode. In operation without cooling the air humidity increases, so the windows may mist up from inside. The quality of the passenger compartment air deteriorates, which may cause the vehicle occupants to feel drowsy.
106 Climate control Controls for: ■ Temperature ■ Air distribution and menu selection ■ Fan speed AUTO = Automatic mode 4 = Air recirculating V = Demisting and defrosting Heated rear window Ü 3 31. The preselected temperature is automatically regulated.
Climate control 107 To return to automatic mode: Press AUTO button. Demisting and defrosting the windows Press the V button. V appears in the display. Temperature and air distribution are set automatically and the fan runs at a high speed. To return to automatic mode: Press button V or AUTO .
108 Climate control If no cooling or drying is required, deactivate AC to save fuel. When the cooling system is switched off, no engine restart will be requested by the climate control system during an Autostop. Depending on the vehicle equipment, the display will indicate AC when cooling is activated or Eco when the cooling is deactivated.
Climate control 109 Auxiliary heater Air heater Quickheat is an electric auxiliary air heater which automatically warms up the passenger compartment more quickly.
110 Climate control Maintenance Air intake The air intake in front of the windscreen in the engine compartment must be kept clear to allow air intake. Remove any leaves, dirt or snow. Pollen filter The pollen filter cleans dust, soot, pollen and spores from the air entering the vehicle through the air intake.
Driving and operating 111 Driving and operating Driving hints ............................... 111 Starting and operating ............... 111 Engine exhaust .......................... 115 Automatic transmission .............. 117 Manual transmission ..
112 Driving and operating Ignition switch positions 0 = Ignition off 1 = Steering wheel lock released, ignition off 2 = Ignition on, for diesel engine: preheating 3 = Starting Starting the engine Operate clutch and brake, if the clutch pedal is not operated the engine might not start and the control indicator - could illuminate.
Driving and operating 113 Overrun cut-off The fuel supply is automatically cut off during overrun, i.e. when the vehicle is driven with a gear engaged but accelerator is released. Overrun cut- off is deactivated if catalytic converter temperature is high.
114 Driving and operating ■ the battery is sufficiently charged and in good condition ■ the engine is warmed up ■ the engine coolant temperature is not too high ■ the engine exhaust temperature is not too high, e.
Driving and operating 115 ■ the climate control system requests an engine start ■ the air conditioning is manually switched on If the bonnet is not fully closed, a warning message is displayed in the Driver Information Centre. If an electrical accessory, e.
116 Driving and operating consumption may be higher during this period. The emission of smells and smoke during this process is normal. Under certain driving conditions, e.
Driving and operating 117 Caution Fuel grades other than those listed on pages 3 130, 3 195 could damage the catalytic converter or electronic components. Unburnt petrol will overheat and damage the catalytic converter. Therefore avoid excessive use of the starter, running the fuel tank dry and starting the engine by pushing or towing.
118 Driving and operating The engine can only be started with lever in position P or N . When position N is selected, press brake pedal or apply parking brake before starting. Do not accelerate while engaging a gear. Never depress the accelerator pedal and brake pedal at the same time.
Driving and operating 119 Activation Press the T button with P , R , N , D or 3 engaged. The vehicle starts off in 3rd gear. Deactivation The Winter programme is switched off by: ■ pressing the T button again, ■ manually selecting 2 or 1 , ■ turning off the ignition, ■ or if the transmission oil temperature is too high.
120 Driving and operating 3. Push the yellow catch forward with a screwdriver and move the selector lever out of P . If P is engaged again, the selector lever will be locked in position again. Have the cause of the power supply interruption remedied by a workshop.
Driving and operating 121 Manual transmission automated The Easytronic transmission permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control.
122 Driving and operating If neither the accelerator nor the brake pedal are depressed, no gear is engaged and A or R flashes for a brief time in the display. Stopping the vehicle In A , first gear is engaged and the clutch is released when the vehicle is stopped.
Driving and operating 123 Sport mode Shift times are reduced when the Sport mode is enabled, and the gears are shifted at higher engine speeds, although not when cruise control is activated.
124 Driving and operating Kickdown If the accelerator pedal is pressed past the pressure point, the transmission shifts to a lower gear depending on engine speed. Fault To prevent damage to the manual transmission automated, the clutch is engaged automatically at high clutch temperatures.
Driving and operating 125 5. Using a flat-head screwdriver, turn the adjusting screw under the cap clockwise until clear resistance can be felt. The clutch has now been disengaged. 6. Refit cleaned cap. The cap must be in full contact with the housing.
126 Driving and operating Fault 9 Warning If there is a fault in the ABS, the wheels may be liable to lock due to braking that is heavier than normal. The advantages of ABS are no longer available. During hard braking, the vehicle can no longer be steered and may swerve.
Driving and operating 127 Ride control systems Electronic stability program Electronic stability program (ESP® Plus ) improves driving stability when necessary, regardless of the type of road surface or tyre grip. It also prevents the drive wheels from spinning.
128 Driving and operating Driver assistance systems Cruise control The cruise control can store and maintain speeds of approx. 20 to 120 mph. Deviations from the stored speeds may occur when driving uphill or downhill. For safety reasons the cruise control cannot be activated until the foot brake has been operated once.
Driving and operating 129 To reset the saved speed, turn switch g downwards. Parking assist The parking assist makes parking easier by measuring the distance between the vehicle and obstacles, and giving acoustic signals. It is the driver, however, who bears full responsibility for the parking manoeuvre.
130 Driving and operating Caution Performance of the sensors can be reduced when sensors are covered, e.g. by ice or snow. Performance of the parking assist systems can be reduced due to heavy loading. Special conditions apply if there are taller vehicles involved (e.
Driving and operating 131 Caution Use of fuel that does not comply to EN 228 or E DIN 51626-1 or equivalent can lead to deposits or engine damage and may affect your warranty. Caution Use of fuel with too low an octane rating could lead to uncontrolled combustion and engine damage.
132 Driving and operating Pressing the LPG button switches between petrol and liquid gas operation as soon as the required parameters (coolant temperature, gas temperature and minimum engine speed) have been reached. The requirements are usually fulfilled after approx.
Driving and operating 133 Turn the thumb wheel clockwise. If no further gas odour is perceptible when the manual shut-off valve is closed, the vehicle can be used in petrol mode. If the gas odour persists, do not start the engine. Have the cause of the fault remedied by a workshop.
134 Driving and operating Unlock the fuel filler cap with the ignition key. To open, turn the cap slowly to the left. The fuel filler cap can be retained in the bracket on the fuel filler flap. For refuelling, fully insert the pump nozzle and switch it on.
Driving and operating 135 DISH (Italy) filler neck: Place the filler nozzle into the adapter. Press locking lever on filler nozzle down. Bayonet filler neck: Place filler nozzle on the adapter and turn to the left or right through one quarter turn. Pull locking lever of filler nozzle fully.
136 Driving and operating EURO adapter: Spain DISH (Italy) adapter: Bosnia- Herzegovina, Bulgaria, Denmark, Estonia, France, Greece, Italy, Croatia, Latvia, Lithuania, Macedonia, Austria, Poland, Port.
Driving and operating 137 Towing General information Only use towing equipment that has been approved for your vehicle. Entrust retrofitting of towing equipment to a workshop. It may be necessary to make changes that affect the cooling system, heat shields or other equipment.
138 Driving and operating The maximum permissible vertical coupling load (vehicles with 1.2 engine: 45 kg, other engines: 55 kg) is specified on the towing equipment identification plate and in the vehicle documents. Always aim for the maximum load, especially in the case of heavy trailers.
Driving and operating 139 Push both bolts inwards and remove the cover on the bumper. Disengage and fold down the socket. Remove the sealing plug from the opening for the coupling ball bar and stow it. Checking the tensioning of the coupling ball bar ■ The rotary knob rests on the coupling ball bar.
140 Driving and operating Inserting the coupling ball bar Insert the tensioned coupling ball bar in the opening and push firmly upwards until it audibly engages. The rotary knob snaps back into its original position resting against the coupling ball bar without a gap.
Driving and operating 141 Dismounting the coupling ball bar Insert the key in the lock and unlock the coupling ball bar. Push the rotary knob onto the coupling ball bar and rotate right while pressed down until it engages. Pull out the ball bar downwards.
142 Vehicle care Vehicle care General Information ................... 142 Vehicle checks ........................... 143 Bulb replacement ....................... 150 Electrical system ........................ 163 Vehicle tools ........................
Vehicle care 143 ■ Open bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery. Beware that all systems are not functional, e.
144 Vehicle care 9 Danger The ignition system and Xenon headlights use extremely high voltage. Do not touch. The caps for topping up the engine oil, the coolant, the washer fluid and the oil dipstick handle are yellow, for ease of identification. Bonnet Opening Pull the release lever and return it to its original position.
Vehicle care 145 Engine oil Check the engine oil level manually on a regular basis to prevent damage to the engine. Ensure that the correct specification of oil is used. Recommended fluids and lubricants 3 187. Check with the vehicle on a level surface.
146 Vehicle care Fit the cap on straight and tighten it. Engine coolant The coolant provides freeze protection down to approx. -28 °C. Caution Only use approved antifreeze. Coolant level Caution Too low a coolant level can cause engine damage. If the cooling system is cold, the coolant level should be above the KALT/COLD mark.
Vehicle care 147 Caution Only washer fluid with a sufficient antifreeze concentration provides protection at low temperatures or a sudden drop in temperature. Brakes A squealing noise indicates that the brake lining is at its minimum thickness. Continued driving is possible but have the brake lining replaced as soon as possible.
148 Vehicle care Laying up the vehicle for more than 4 weeks can lead to battery discharge. Disconnect the clamp from the negative terminal of the vehicle battery. Ensure the ignition is switched off before connecting or disconnecting the vehicle battery.
Vehicle care 149 Note Using an AGM battery different from the original Vauxhall battery might result in a lower performance of the stop-start system. We recommend that you have the battery replaced by a workshop.
150 Vehicle care Wiper blades on the windscreen Lift the wiper arm, tilt wiper blade at a 90° to the wiper arm and remove to the side. Wiper blade on the rear window Lift wiper arm. Disengage wiper blade as shown in illustration and remove. Attach the wiper blade slightly angled to the wiper arm and push until it engages.
Vehicle care 151 To replace the bulb on the left-hand side, remove fuse box cover 3 165, and also remove windscreen washer system reservoir filler neck from above.
152 Vehicle care High beam 1. Rotate protective cover 2 anticlockwise and remove. 2. Detach wiring plug from bulb. 3. Disengage spring clip from retainer by moving and swivelling to the side. 4. Remove bulb from reflector housing. 5. When installing the new bulb, insert lugs in the reflector recesses.
Vehicle care 153 2. Remove bulb from socket, insert new bulb. 3. Insert bulb holder in reflector so that the locating tab of the bulb holder aligns with the reflector recess. 4. Rotate clockwise to engage. Front turn signal light Front turn signal lights are equipped with longlife bulbs.
154 Vehicle care 2. Rotate bulb holder anticlockwise to disengage. Withdraw bulb holder from reflector. 3. Insert new bulb in reflector so that the locating tab of the bulb holder aligns with the reflector recess. 4. Engage bulb holder by turning clockwise.
Vehicle care 155 Cornering light 1. Rotate protective cover 2 anticlockwise and remove. 2. Detach wiring plug from bulb. 3. Disengage spring clip from retainer by moving and swivelling to the side. 4. Remove bulb from reflector housing. 5. When installing the new bulb, insert lugs in the reflector recesses.
156 Vehicle care 2. Rotate bulb holder anticlockwise to disengage. Withdraw bulb holder from reflector. 3. Push bulb into socket slightly, rotate anti-clockwise and remove. 4. Insert new bulb by slightly pressing and rotating. 5. Insert bulb holder in reflector and engage by turning clockwise.
Vehicle care 157 Tail lights 5-door passenger vehicle 1. Open side cover. When replacing bulbs on the right hand side, first remove the tools and the jack or the tyre repair kit, then remove the tool box. 2. Remove plug connector by pressing on bulb holder tab.
158 Vehicle care 5. Gently press the three locking lugs on the outside of the bulb holder outwards and remove bulb holder. 6. Push bulb into socket slightly, rotate anti-clockwise, remove and renew bulb.
Vehicle care 159 3-door passenger vehicle, van 1. Open side cover. When replacing bulbs on the right hand side, first remove the tools and the jack or the tyre repair kit, then remove the tool box. 2. Remove plug connector by pressing on bulb holder tab.
160 Vehicle care 5. Gently press the three locking lugs on the outside of the bulb holder outwards and remove bulb holder. 6. Push bulb into socket slightly, rotate anti-clockwise, remove and renew bulb.
Vehicle care 161 2. Turn bulb holder anticlockwise and remove from housing. 3. Pull bulb from bulb holder and replace it. 4. Insert bulb holder and turn clockwise. 5. On left side: insert front end into front wing, slide forward and insert rear end. On right side: insert rear end into front wing, slide rearward and insert front end.
162 Vehicle care 4. Rotate bulb holder anti-clockwise to disengage. 5. Remove bulb from holder and renew bulb. 6. Insert bulb holder in bulb housing and rotate clockwise. 7. Connect wiring plug to bulb holder. 8. Insert and engage bulb housing. Interior lights Front courtesy light 1.
Vehicle care 163 Glovebox light, foot well light 1. Prise the lamp out with a screwdriver. 2. Press bulb slightly towards spring clip and remove. 3. Insert new bulb. 4. Install lamp. Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse.
164 Vehicle care Engine compartment fuse box The fuse box is in the front left of the engine compartment. Disengage the cover, lift it upwards and remove.
Vehicle care 165 No. Circuit 1 Starter 2 Air conditioning system 3 Diesel fuel filter heater 4 Horn 5 Manual transmission auto‐ mated, automatic transmission 6 Engine control unit 7 Fog lights 8 Eng.
166 Vehicle care In right-hand drive vehicles, the fuse box is located behind a cover in the glovebox. Open the glovebox and remove the cover. To close, first put on the cover, then lock it into position.
Vehicle care 167 The fuse box is on the left side of the load compartment behind a cover. Remove the cover. No. Circuit 1 Adaptive forward lighting 2 – 3 Seat heater (left) 4 Seat heater (right) 5 – 6 – No.
168 Vehicle care Vehicles with spare wheel Variant 1: The jack and the vehicle tools are in the load compartment underneath the spare wheel. A label on the jack indicates the vehicles for which the jack can be used. Variant 2: The jack and the vehicle tools are in the right-hand compartment in the load compartment.
Vehicle care 169 Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage.
170 Vehicle care Tyre pressure 3 212 and on the label on the inside of the fuel filler flap or on the front right door frame. The tyre pressure data refers to cold tyres. It applies to summer and winter tyres. Always inflate the spare tyre to the pressure specified for full load.
Vehicle care 171 For safety reasons it is recommended that the tread depth of the wheels on one axle should not vary by more than 2 mm. The legally permissible minimum tread depth (1.6 mm) has been reached when the tread has worn down as far as one of the tread wear indicators (TWI).
172 Vehicle care Tyre chains Tyre chains are only permitted on the front wheels. Always use fine mesh chains that add no more than 10 mm to the tyre tread and the inboard sides (including chain lock).
Vehicle care 173 To open the compartment, disengage the cover and open it. 1. Take the sealant bottle and bracket with air hose from the insert. 2. Detach air hose from bracket and screw onto sealant bottle connection. 3. Position the sealant bottle on the bracket.
174 Vehicle care 8. Press on/off switch on the compressor. The tyre is filled with sealant. 9. The compressor pressure gauge briefly indicates up to 6 bar whilst the sealant bottle is emptying (approx. 30 seconds). Then the pressure starts to drop. 10.
Vehicle care 175 Note The driving characteristics of the repaired tyre are severely affected, therefore have this tyre replaced. If unusual noise is heard or the compressor becomes hot, turn compressor off for at least 30 minutes. The built-in safety valve opens at a pressure of 7 bar (102 psi).
176 Vehicle care Alloy wheels: Disengage wheel bolt caps with a suitable screwdriver and remove. To protect the wheel, place a soft cloth between the screwdriver and the alloy wheel. 2. Install the wheel wrench ensuring that it locates securely and slacken each bolt by half a turn.
Vehicle care 177 Variant 2: Attach jack handle and with the jack correctly aligned rotate handle until wheel is clear of the ground. 5. Unscrew the wheel bolts. 6. Change the wheel. 7. Screw in the wheel bolts. 8. Lower vehicle. 9. Install the wheel wrench ensuring that it locates securely and tighten each bolt in a crosswise sequence.
178 Vehicle care In the Corsa van the spare wheel is screwed down together with the floor cover. To lift the cover, undo the plastic nut. There is a spacer between the spare wheel and the floor cover. The spare wheel well is not designed for all permitted tyre sizes.
Vehicle care 179 Note Any deviation from the instructions given in this paragraph may lead to a temporary deactivation of the stop- start system. ■ Never expose the battery to naked flames or sparks. ■ A discharged battery can already freeze at temperatures of 0 °C.
180 Vehicle care Position the leads so that they cannot catch on rotating parts in the engine compartment. To start the engine: 1. Start the engine of the vehicle providing the jump. 2. After 5 minutes, start the other engine. Start attempts should be made for no longer than 15 seconds at an interval of 1 minute.
Vehicle care 181 The towing eye is stowed with the vehicle tools 3 167. The towing eye is located in a recess. Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or better still a tow rod – to the towing eye.
182 Vehicle care The towing eye is stowed with the vehicle tools 3 167. Screw in the towing eye as far as it will go until it stops in a horizontal position. The lashing eye at the rear underneath the vehicle must never be used as a towing eye. Attach a tow rope – or better still a tow rod – to the towing eye.
Vehicle care 183 If using a car wash, comply with the car wash manufacturer's instructions. The windscreen wipers and rear window wiper must be switched off. Remove antenna and external accessories such as roof racks etc. If you wash your vehicle by hand, make sure that the insides of the wheel housings are also thoroughly rinsed out.
184 Vehicle care Clean rims with a pH-neutral wheel cleaner. Rims are painted and can be treated with the same agents as the body. Paintwork damage Rectify minor paintwork damage with a touch-up pen before rust forms. Have more extensive damage or rust areas repaired by a workshop.
Vehicle care 185 Caution Close Velcro fasteners as open Velcro fasteners on clothing could damage seat upholstery. The same applies to clothing with sharp-edged objects, like zips or belts or studded jeans. Plastic and rubber parts Plastic and rubber parts can be cleaned with the same cleaner as used to clean the body.
186 Service and maintenance Service and maintenance General information ................... 186 Recommended fluids, lubricants and parts ..............
Service and maintenance 187 Fixed service interval When service is due, InSP appears in the odometer display for approx. 10 seconds when the ignition is switched on. Have the next service performed by a workshop within one week or 300 miles (whichever occurs first).
188 Service and maintenance aging control, whereas viscosity grade gives information on the oil's thickness over a temperature range. Dexos is the newest engine oil quality that provides optimum protection for gasoline and diesel engines. If it is unavailable, engine oils of other listed qualities have to be used.
Service and maintenance 189 Brake fluid should be stored in a sealed container to avoid water absorption. Ensure brake fluid does not become contaminated.
190 Technical data Technical data Vehicle identification .................. 190 Vehicle data ............................... 192 Vehicle identification Vehicle Identification Number The Vehicle Identification Number is stamped on the identification plate and on the floor pan, under the floor covering, visible under a cover.
Technical data 191 Information on identification plate: 1 = Manufacturer 2 = Type approval number 3 = Vehicle Identification Number 4 = Permissible gross vehicle weight rating in kg 5 = Permissible gr.
192 Technical data Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries ( except Belarus, Moldova, Russia, Serbia, Turkey) Only I.
Technical data 193 International service schedule Required engine oil quality All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Engine oil quality Petrol engines.
194 Technical data All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Engine oil quality Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (i.
Technical data 195 Engine data Sales designation 1.0 1.2 1.2 1.4 Engine identifier code A10XEP A12XEL A12XER A14XEL Piston displacement [cm 3 ] 998 1229 1229 1398 Engine power [kW] 48 51 63 2) 64 at r.
196 Technical data Sales designation 1.4 1.4 1.6 VXR 1.6 VXR Nürburgring Edition Engine identifier code A14XER A14NEL A16LER A16LES Piston displacement [cm 3 ] 1398 1364 1598 1598 Engine power [kW] 7.
Technical data 197 Sales designation 1.3 CDTI 1.3 CDTI 1.3 CDTI 1.3 CDTI 1.7 CDTI Engine identifier code Z13DTJ A13DTE Eco A13DTC A13DTR A17DTS Piston displacement [cm 3 ] 1248 1248 1248 1248 1686 Eng.
198 Technical data Performance 5-door vehicle Engine A10XEP A12XEL A12XER A14XEL A14XER A14NEL Maximum speed 4) [mph] Manual transmission 96 99 107 5)6) 108 112 121 Manual transmission automated – .
Technical data 199 3-door vehicle Engine A10XEP A12XEL A12XER A14XEL A14XER Maximum speed 4) [mph] Manual transmission 96 99 107 5)6) 108 112 Manual transmission automated – – 107 – – Automati.
200 Technical data Engine A13DTC A13DTR A17DTS Maximum speed 4) [mph] Manual transmission 101 108 124 Manual transmission automated – – – Automatic transmission – – – Van Engine A10XEP A12.
Technical data 201 Engine Z13DTJ A13DTC A13DTE Eco A13DTR Maximum speed 4) [mph] Manual transmission 101 101 110 108 Manual transmission automated – – – – Automatic transmission – – – – 4) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload.
202 Technical data Vehicle weight Kerb weight, 5-door vehicle, basic model without any optional equipment Corsa Engine Manual transmission Manual transmission automated Automatic transmission without/.
Technical data 203 Corsa Engine Manual transmission Manual transmission automated Automatic transmission A13DTR 1265/1285 1265/1285 – A17DTS 1320/1340 – – Kerb weight, 5-door vehicle, basic mode.
204 Technical data Corsa Engine Manual transmission Manual transmission automated Automatic transmission without/with air conditioning or electronic climate control [kg] A13DTE ECO –/1318 –/1318 .
Technical data 205 Kerb weight, 3-door vehicle, basic model without any optional equipment Corsa Engine Manual transmission Manual transmission automated Automatic transmission without/with air condit.
206 Technical data Corsa Engine Manual transmission Manual transmission automated Automatic transmission without/with air conditioning or electronic climate control [kg] A13DTE ECO 1163/1173 1163/1173.
Technical data 207 Kerb weight, 3-door vehicle, basic model with all optional equipment Corsa Engine Manual transmission Manual transmission automated Automatic transmission without/with air condition.
208 Technical data Kerb weight, van, basic model without any optional equipment Corsa Engine Manual transmission Manual transmission automated Automatic transmission without/with air conditioning or e.
Technical data 209 Kerb weight, van, basic model with all optional equipment Corsa Engine Manual transmission Manual transmission automated Automatic transmission without/with air conditioning or elec.
210 Technical data 5-door vehicle 3-door vehicle VXR Van Length of load compartment with folded rear seats [mm] 1348 1348 1348 – Load compartment width [mm] 944 944 944 944 Load compartment height [mm] 538 538 538 538 Wheelbase [mm] 2511 2511 2511 2511 Turning circle diameter [m] 10.
Technical data 211 Capacities Engine oil Engine A10XEP A12XEL, A12XER A14XEL, A14XER, A14NEL A16LER, A16LES A13DTE, A13DTC A13DTR, Z13DTJ A17DTS including Filter [l] 3.
212 Technical data Tyre pressures Comfort with up to 3 people ECO with up to 3 people 18) With full load Engine Tyres front rear front rear front rear [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) A10XEP 185/70 R14, 200/2.
Technical data 213 Comfort with up to 3 people ECO with up to 3 people 18) With full load Engine Tyres front rear front rear front rear [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) A12XEL, A12XER, A14XEL, A14XER 185/70 R14, 200/2.
214 Technical data Comfort with up to 3 people ECO with up to 3 people 18) With full load Engine Tyres front rear front rear front rear [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) A14NEL 195/65 R15, 230/2.
Technical data 215 Comfort with up to 3 people ECO with up to 3 people 18) With full load Engine Tyres front rear front rear front rear [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) A13DTC 185/65 R15 23) , 200/2.
216 Technical data Comfort with up to 3 people ECO with up to 3 people 18) With full load Engine Tyres front rear front rear front rear [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) A13DTR 185/60 R15 240/2.
Technical data 217 Comfort with up to 3 people ECO with up to 3 people 18) With full load Engine Tyres front rear front rear front rear [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) Z13DTJ 185/70 R14 27) , 200/2.
218 Technical data Comfort with up to 3 people ECO with up to 3 people 18) With full load Engine Tyres front rear front rear front rear [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) A17DTS 185/65 R15 28) , 240/2.
Customer information 219 Customer information Vehicle data recording and privacy ....................................... 219 Vehicle data recording and privacy Event data recorders Data storage module.
220 Customer information When using the vehicle, situations may occur in which these technical data related to other information (accident report, damages on the vehicle, witness statements etc.) may be associated with a specific person - possibly, with the assistance of an expert.
Customer information 221.
222 Index A Accessories and vehicle modifications .......................... 142 Active head restraints ................... 35 Adaptive forward lighting .......... .................................... 83, 97, 153 Adjustable air vents .................
223 Climate control ............................. 15 Climate control systems ............. 103 Clock ............................................ 72 Control indicators.......................... 76 Control of the vehicle ................. 111 Controls .
224 Heated rear window ..................... 31 Heated steering wheel ................. 69 Heating ........................................ 38 Heating and ventilation system . 103 High beam ............................. 82, 96 Hill start assist ......
225 R Radio Frequency Identification (RFID) ..................................... 220 Radio remote control ................... 20 Reading lights ............................ 101 Rear carrier system ...................... 52 Rear floor storage cover ..
226 V Vehicle checks............................ 143 Vehicle data ................................ 192 Vehicle data recording and privacy ..................................... 219 Vehicle dimensions .................... 209 Vehicle Identification Number .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Vauxhall Corsa (2013) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Vauxhall Corsa (2013) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Vauxhall Corsa (2013), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Vauxhall Corsa (2013) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Vauxhall Corsa (2013), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Vauxhall Corsa (2013).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Vauxhall Corsa (2013). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Vauxhall Corsa (2013) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
