Manuel d'utilisation / d'entretien du produit XC 320 du fabricant Uniden
Aller à la page of 28
uni ~n@ XC 320 Cordless Telephone Operating Guide For Australia and New Zealand.
Table of Contents Important Safety Instructions 3 About your XC 320 5 Unpacking 5 XC 320 Features """"""""""""""""""""""""""" 6 Automatic Digital Code Security.
PRECAUTIONS Before you read anything else, please observe the following: WARNING! Uniden Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture.
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: 1. Read and understand all instructions.
12.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. If the power supply cord is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water.
About Your XC 320 Congratulations on your purchase of the Uniden XC 320 Cordless Telephone. The XC 320 is designed and engineered to exacting standards for reliability, long life, and outstanding performance. To get the most from your XC 320, please read this Operating Guide thoroughly.
XC 320 Featu res . UltraClear Plus noise reduction provides the quality sound of a corded telephone. . Eight 30/39 MHz Channels (Australia): Three 30/39 MHz Channels (New Zealand) . 20-Number Memory . Maximum Operating Range . One-Touch Memory Dialing .
Base Unit Controls & Functions RING - OFF LO HI Switch TEL LINE TONE PULSE Switch ~ DCIN9V +%- Handset Retainer INUSE LED I BASE UNIT Antenna I Speaker I8B1 ........... ........... ........... ........... ........... ........... ........... ......
Base Unit Ringer Switch TONE/PULSE Switch TEL LINE Jack DC Input Jack Handset Retainer Base Unit Antenna Speaker Microphone IN USE LED CHARGE LED PAGE/INT'COM Button Use to set the ring volume level ("LO" or "HI") of the Base Unit for incoming calls, or the page alert tone level when paged from the Handset.
Handset Controls & Functions 1 - 9, 0, TONE *, # Button ONE-TOUCH DIAL Buttons INT'C Button FLASH/A. TONE Button Handset Antenna CHANNEL Button AING ON BA TT SAVE Switch ~ -J;, - ~ ~ ~..' MEM Button ~- ~if ~ RDUP Button K -rl- A VOLUME/A.
Use for dialing numbers and storing numbers in memory . ONE-TOUCH DIAL Special memory locations for storing numbers. Press Buttons the appropriate button to dial a number. INT'C Button Use to page the Base Unit and establish communication between the Handset and the Base Unit.
Installing the Telephone on a Desk or Tabletop Place the Base Unit on a desk or tabletop, and plug one end of the Telephone Line Cord (supplied) into the "TEL LINE" jack on the Base.
Read This Before Installation We have designed your telephone to conform to Australia or New Zealand Radio Frequency regulations, and you can connect it to most telephone lines. However, each device that you connect draws power from the phone line. We refer to the power drawn as the devices ringer equivalence number or REN.
If you are mounting the XC 320 on an existing standard wall plate: 1. Plug one end of the Telephone Line Cord (supplied) into the "TEL LINE" jack on the top of the Base Unit. Lay the cord inside the molding on the bottom of the Base Unit. Then plug the other end of the cord into the telephone wall socket.
1. Remove the battery compartment cover on the Handset by sliding it down. 2. Connect the Nickel-Cadmium Battery Pack by plugging it into the socket at the top of the battery compartment. Note: The connector fits only one way and requires only a minimal amount of pressure to insert.
Low Battery Indicator When the Battery Pack in the Handset is very Iow and needs to be charged, the TALKlBATT LOW LED flashes every 3 seconds. If this occurs while you are on the phone, a short alert beep will also sound. When this happens, complete your call as quickly as possible, and return the Handset to the Base Unit for charging.
Setting the Base Unit Ringer Volume To enable the Base Unit to ring when an incoming call is received, or when a page is sent from the Handset, set the BASE UNIT RINGER switch to either "LO" or "HI". Placing a Call To place a call with your XC 320: 1.
Using the Redial Button RDLlP dials the last number that you called. This feature is extremely useful when the number you called is busy. To use this feature, simply press FLASH, then RDLlP. The last number called will then be dialed again. NOTE: If any other key is pressed before RDLlP, the phone will not redial the last number.
NOTE: You have 20 seconds after pressing MEM to enter the number you wish to store. Otherwise, an error tone will sound. 5. Write the stored number and its memory location number on one of the enclosed stickers so you won't forget them.
NOTE: You can also store a mixed tone-pulse number in a ONE-TOUCH DIALlNG button. To do this, follow steps 2 through 5 in "Storing a Mixed Tone/Pulse Number". 4. Press MEM, and the ONE-TOUCH DIALlNG button (1,2, or 3) you wish to program. You will hear a long beep when the number you have entered has been successfully stored.
Using the 2-Way Page/Intercom Feature The 2-Way Page/Intercom feature allows you to communicate between the Base Unit and Handset. To use the Page/Intercom feature: . The RING ON/BATT SAVE switch on the Handset must be in the "RING ON" position.
To use the Page/Intercom from the Handset: 1. Press the INT'C button. You will hear a series of 3 beep tones until the party answers the Base Unit. If there is no answer, press the INT'C button to disconnect. 2. When the other person answers, the page alert stops, and the "TALK" LED on the Base Unit lights.
Troubleshooting If your XC 320 Cordless Telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact Uniden Customer Service for assistance. Note: Do not attempt to service this unit yourself.
Important Electrical Considerations Unplug all electrical appliances when you know an electrical storm is approaching. Lightning can pass through your household wiring and damage any device connected to it. The XC 320 is no exception. NOTE: Please do not attempt to unplug any appliance during an electrical storm.
Maintenance Care Your xc 320 Cordless Telephone is an example of superior design and craftsmanship. The following suggestions will help you care for your phone so that you can enjoy it for years. Keep the phone dry. If it does get wet, wipe it dry immediately.
Specifications General Frequency Control Modulation Operating Temperature Base Receive Frequency Transmit Frequency Power Requirements Size Weight Handset Receive Frequency Transmit Frequency Power Requirements Size Weight Battery Crystal controlled transmission FM -1 0° to 50° C 39.
WARRANTY Uniden XC 320 1 Year Warranty (Batteries and Accessories are covered for 90 days only) Note: Please keep your sales docket as it provides evidence of warranty. Warranty is only valid in the country where the product has been purchased. WARRANTOR: Uniden Australia Pty.
unid~n@ Australia Pty. Ltd. 345 Princes Hwy, Rockdale, NSW. 2216. Ph (02) 599 3355 Fax (02) 599 4018 New Zealand Limited Cnr Ti Rakau Dri ye and Harris Road. East Tamaki, AUCKLAND Ph (9) 274 4179 Fax (9) 274 0009 CELLULAR TELEPHONES, CORD LES S TELEPHONES SCANNERS, CB RADIOS, UHF RADIO, MARINE RADIO, LAND MOBILE RADIO.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Uniden XC 320 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Uniden XC 320 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Uniden XC 320, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Uniden XC 320 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Uniden XC 320, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Uniden XC 320.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Uniden XC 320. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Uniden XC 320 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
