Manuel d'utilisation / d'entretien du produit ANA9320 du fabricant Uniden
Aller à la page of 41
.
One Year Limited Warranty WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below.
.
PRECAUTIONS Before you read anything else, please observe the following: WARNING! Uniden America Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture.
Handset Controls & Functions 1. Headset Jack 2. Message Display 3. Pause ( pause ) Key 4. Talk ( TALK ) Key 5. Numeric Keypad 6. L2 Key 7. L1 Key 8. Microphone 9. Hold ( hold ) Key 10. Flash ( flash ) Key 11. Channel ( CH ) Key 12. Redial ( redial ) Key 13.
Base Unit Controls & Functions 18. line 1 LED 19. power/status LED 20. line 2 LED 18 20 19 7 Y:...ANA9320 om.vp Tue Dec 03 15:21:27 2002 Color profile: Disabled Composite Default screen.
1 TABLE OF CONTENTS Important Safety Instructions ............................................... 2 About Your ANA 9320 ..................................................... 4 Important Electrical Considerations .......................................
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: 1. Read and understand all instructions.
D. If the product does not operate normally when following the operating instructions. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage, and will often require extensive work by a qualified technician to restore the product to normal operation.
About Your ANA 9320 Congratulations on your purchase of the Uniden ANA 9320 Cordless Telephone. The ANA 9320 is designed and engineered to exacting standards for reliability, long life, and outstanding performance. It is designed to work with a PBX system.
Important Electrical Considerations Warning: Please do not attempt to unplug any appliance during an electrical storm. Unplug all electrical appliances when you know an electrical storm is approaching. Lightning can pass through your household wiring and damage any device connected to it.
Radio Interference Radio interference may occasionally cause buzzing and humming in your cordless Handset, or clicking noises in the Base Unit. This interference is caused by external sources such as a TV, refrigerator, vacuum cleaner, fluorescent lighting, computer equipment, or electrical storm.
ANA 9320 Features n Long Range 900MHz Digital n 2-line, 16-digit LCD Display n Ringer Volume Control n Handset Volume Control n Single button access to: CONFERENCE, HOLD, and TRANSFER features n Four .
Installing Your ANA 9320 Selecting the Installation Location Select a location for the ANA 9320 to avoid excessive heat or humidity. The Base Unit of your ANA 9320 can be placed on a desk or tabletop near a standard 120V AC outlet and telephone line jack.
Connecting the Telephone Cords The ANA 9320 must be connected to a PSTN or an analog PBX port telephone line. TIP: To setup PSTN or PBX, refer to page 24.
Applying Power to the Base and Charger Units Use only the supplied AC Adapter: EXP9704 IMPORTANT! Route the power cord where it will not create a trip hazard, or where it could become chafed and create a fire or other electrical hazards. Note: If you cannot plug the AC Adapter into the outlet, contact someone about replacing the outlet.
Wall Installation Standard Wall Plate Mounting These Phones are designed to be mounted on a standard wall plate. To attach the wall mount stand to the Base Unit: 1. Slide the Wall Mount stand into the notches at the top of the Base Unit, push the Wall Mount stand down and snap it into place.
6. Place the Base Unit on the posts of the wall plate and push down until it’s firmly seated. 7. Plug the AC Adapter into a standard 120V AC wall outlet. Note: Do not use an outlet controlled by a wall switch. Direct Wall Mounting If you do not have a standard wall plate, you can mount your phone directly on a wall.
1. Insert two mounting screws 3 15/16 inches apart. Allow about 3/16 of an inch between the wall and screw heads for mounting the phone. 2. Plug and secure the AC Adapter cord by following steps 2 and 3o ft h e Standard Wall Plate Mounting. 3. Plug one end of the telephone line cord into the LINE jack on the Base Unit.
Charging Unit Wall Mounting The Charging Unit is also designed to be wall mounted. Before mounting your charging unit, consider the following: n Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall.
3. Slide the wall mount stand into the notches on the bottom of the charging unit. 4. Place the Charging Unit on the posts of the wall screws and push down until it’s firmly seated. 5. Plug the AC Adapter into a standard 120V AC wall outlet. 15 23 Y:.
Attaching the Belt Clip to the Handset You can use the Belt Clip to attach the Handset to your belt or pocket for convenient portability. 1. Snap the tab out of the Belt Clip notch on the top of the Handset. 2. Slide the clip into the tab slot. ( CAUTION: The Belt Clip is designed to fit snugly onto the Handset.
Installing the Handset Battery Pack 1. Remove the battery cover by pressing the latch and sliding the cover down and off of the Handset. 2. Connect the battery pack connector observing correct polarity to the jack inside the battery compartment. Do not exert any force on this connection.
Charging the Handset Battery Pack The Rechargeable Ni-MH Battery Pack must be fully charged before using your ANA 9320 for the first time. ( Note: Charge the Battery Pack without interruption for 5 hours. ) 1. Place the Handset into the Charging Unit.
Using Your ANA 9320 Handset Before using your ANA 9320 , be sure to raise the antenna to the vertical position. Note: Operation of the ANA 9320 is performed using the Handset out of the Charging Unit.
Earpiece Volume Press RING/VOL on the side of the Handset during a call to select the earpiece volume of the handset. 20 28 Y:...ANA9320 om.vp Tue Dec 03 15:23:52 2002 Color profile: Disabled Composit.
Handset Ringer Tone and Volume Pressing RING / VOL on the side of the Handset in standby mode to select seven ringer tones and volume combinations. Vibrate Mode “ Ring off ” shown on the above display is the Vibrate Mode. If you set the ringer off and the Handset is not on the charger, the Handset will vibrate when there is an incoming call.
Using the Handset When you pick up the Handset and press TALK , you will see: After the connection has been made between the Handset and Base, the display will show the lines currently connected: Or, .
Answering a Call When you receive a call, the Handset rings and you’ll see: Handset in the Charging Unit Handset out of Charging Unit Pick up the Handset. The AutoTalk feature allows you to answer the call immediately. Press TALK. Or press any key on the numeric keypad, hold , pause , flash , conf ,o r xfer .
Programming Functions PBX or PSTN In the Programming mode, you can select either Analog PBX or PSTN (Public Service Telephone Network) operation. The default is PSTN.
Programming Xfer in PBX Note: Before programming these commands, contact your PBX Administrator to obtain programming codes. The xfer key can be programmed for special use, such as causing a "Hook Flash" followed by a special number or function.
Programming Conf in PBX Your PBX system's configuration determines how the conference feature works. Contact your PBX Administrator for exact operation details. The example below is just a representation. For example - to program the conf key for "Hook Flash" and "9": Press and hold pause for two seconds.
Feature Buttons Note: The exact operation of the Feature Buttons depends on how your PBX system is configured. Contact your PBX Administrator for more information. : Placing a call “on hold” Press hold . You will see the following display: To resume the call, press L1 , L2 or TALK .
PBX Features L1 Key Press the L1 key to initiate a call on Line 1. L2 Key Press the L2 key to initiate a call on Line 2. conf Key In PBX mode, the conf (conference) key must first be programmed. Refer to the section entitled "Programming Conf in PBX".
RING/VOL Key This key selects the ringer volume level or tone (or silent alert) during standby mode, and handset earpiece audio level during a call. This key also selects an item during programming mode. CH Key The ANA 9320 automatically selects the clearest of three channels during a call for maximum audio quality.
xfer Key Note: This feature is not available in PSTN mode. hold Key Press once and the call is placed on hold. Press L1 , L2 or TALK to resume the call. pause Key Press once to cause a four second pause while dialing a number. flash Key Press once to cause a "Hook Flash" while on a call.
Optional Headset (EXP9730/EXP9530) The optional Headset provides a “Hands-Free” Option for the ANA 9320. With the Headset installed, you can use the Belt Clip to carry the Handset, and conduct a conversation using the Headset. To install the optional Headset, open the cover over the Headset Jack and plug the Headset in.
Optional Accessories and Replacement Parts For the following Optional Accessories and Replacement Parts contact your PBX Administrator. 32 EXP9704 AC Adapter for Base Unit Telephone Cords Belt Clip EX.
Troubleshooting If your ANA 9320 Cordless Telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact your PBX Administrator. Note: Do not attempt to service this unit yourself.
Specifications Frequency Control : Phase Lock Loop Modulation : FM Operating Temperature : 0° to 50° C (+32° F to +122° F) Base Unit Receive/Transmit Frequency : 902 MHz to 928 MHz Power Requirements : 10V DC from supplied AC Adapter Size : 4 1/4 in .
MEMO 35 43 Y:...ANA9320 om.vp Tue Dec 03 15:25:59 2002 Color profile: Disabled Composite Default screen.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Uniden ANA9320 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Uniden ANA9320 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Uniden ANA9320, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Uniden ANA9320 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Uniden ANA9320, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Uniden ANA9320.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Uniden ANA9320. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Uniden ANA9320 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
