Manuel d'utilisation / d'entretien du produit TSF-72SD du fabricant Turbo Air
Aller à la page of 46
Commercial Refrigerator & Freezer Service Manual Solid Door Model No.: TSR-23SD TSR-49SD TSR-72SD TSF-23SD TSF-49SD TSF-72SD.
1 T ABLE OF CONTENTS 1. FEA TURE CHART 1-1. FRONT VIEW 1-2. SIDE VIEW 2. WIRING DIAGRAM 2-1. REFRIGERATOR (1DOOR) : TSR-23SD 2-2. FREEZER (1DOOR) : TSF-23SD 2-3. REFRIGERATOR (2DOOR) : TSR-49SD 2-4. FREEZER (2DOOR) : TSF-49SD 2-5. REFRIGERATOR (3DOOR) : TSR-72SD 2-6.
1-1. FRONT VIEW 2 1. FEA TURE CHAR T 1 TOP GRILLE PANEL 2 TOP GRILLE 3 TOP GRILLE FIXTURE 4 DOOR SWITCH 5 DOOR LOCK 6 MAIN PCB 7 TRANSFORMER 8 DISPLAY PCB 9 CONTROL BOARD HOUSING 10 BRAND LOGO 11 DOOR.
FEA TURE CHART 1-2. SIDE VIEW 3 l ; zx cv b n m , . / ! @ # $ % 29 DOOR BUMPER 30 DOOR GASKET 31 LAMP BULB 32 LAMP SOCKET 33 EVAPORATOR FAN MOTOR BLADE 34 EVAPORATOR FAN MOTOR 35 EVAPORATOR COIL 36 SU.
2. WIRING DIAGRAM 4 WIRING DIAGRAM 2-1. TSR-23SD WIRING DIAGRAM 2-2. TSF-23SD.
5 WIRING DIAGRAM WIRING DIAGRAM 2-4. TSF-49SD WIRING DIAGRAM 2-3. TSR-49SD.
6 WIRING DIAGRAM WIRING DIAGRAM 2-6. TSF-72SD WIRING DIAGRAM 2-5. TSR-72SD.
7 3. P AR T DET AILS 3-1. TOP GRILLE Door Lock, Switch 3-2. Refrigeration Compartment Cycle Assembly Transformer, Main P.C.B Transformer Harness Door Lock Door Switch Main PCB Suction Pipe Compressor .
8 P ART DET AILS Drain Pan Assembly Condenser Fan Motor Assembly 3-3. Electrical Box Drain Wicking Bar Drain Pan Condenser Fan Motor Bracket Condenser Fan Motor Blade Power Relay (Comp.
9 P ART DET AILS 3-4. Door Gasket 3-5. Cooling Compartment Freezer Duct & Refrigerator Duct (TSR-49SD, TSF-49SD, TSR-72SD, TSF-72SD Type) Freezer Evaporator, Fan (TSF-49SD, TSF-72SD) Gasket Evapor.
10 P ART DET AILS Freezer Duct & Refrigerator Duct (TSR-23SD, TSF-23SD Type) Freezer Evaporator, Fan (TSF-23SD) Lamp & Fan Motor Connectors Evaporator Fan Motor Blade Evaporator Thermal Evapor.
11 4. MAIN COMPONENTS 4-1. COMPRESSOR Model TSR-23SD TSR-49SD TSF-23SD TSF-49SD TSR-72SD TSF-72SD Refrigerant R-134a R-404a R-134a R-404a Voltage 115V / 60Hz 208/230 Comp.
12 MAIN COMPONENTS 4-5. EV A F AN MOTOR Model TSR-23SD TSR-49SD TSF-23SD TSF-49SD TSR-72SD TSF-72SD Voltage 115V / 60Hz Motor Model IS4420DWSN-2A Part code 3963328120 4-6.
21 6. P AR T -LIST OF SOLID DOOR MODEL Caster CASTER 30265L0200 TP5040-22-HDP CASTER BRAKE 30265L0100 TP5040-22-HDP-TLB Compressor COMPRESSOR RUN CAPACITOR 400EL15130 230V/10µF COMPRESSOR START CAPAC.
22 P ART -LIST OF SOLID DOOR MODEL CAPILLARY TUBE (A) 30244Q1000 C1220T L2263 ID ø 3.56 CAPILLARY TUBE (B) 30244Q1100 C1220T L3505 ID ø 2.0 CONDENSER DRYER 30268L0300 C1220T XH-9 50g ø 3.1 CONDENSER DRYER 30268L0400 C1220T XH-9 50g ø 3.5 CONDENSER DRYER 30268Q0100 C1220T XH-9 50g ø 5.
23 P ART -LIST OF SOLID DOOR MODEL DRAIN PAN 30211J0103 HIPS DRAIN WICKING BAR 30230J0700 PVC-H DRAIN WICKING BAR 30230L0100 PVC-H DRAIN WICKING PADS 30245L1000 PULP T2.5 DRAIN WICKING PADS 30245A0700 PULP T2.5 Evaporator DRAIN CAP 30209L0200 PA-6 EVAPORATOR DRAIN PAN 30211L0501 A1100P-H14 0.
24 P ART -LIST OF SOLID DOOR MODEL DUCT (A) 30269L0304 SUS 304 DUCT (A) 30269L0404 SUS 304 DUCT (A) 30269Q0500 SUS 304 DUCT (B) 30269L0507 SUS 304 DUCT (B) 30269L0606 SUS 304 DUCT (B) 30269Q0400 SUS 3.
P ART -LIST OF SOLID DOOR MODEL BOTTOM GRILLE ASSEMBLY 30224L1400 STS304-HL BOTTOM GRILLE ASSEMBLY 30200Q4100 STS304-HL Lamp LAMP SHIELD 30214L3200 PP MILKY LAMP HARNESS 30227L0900 LAMP BULB 30236L0100 25W/120V LAMP SOCKET 30279L0100 MEDIUM BASE L-124B-PVC Shelf SHELF STANDARD 30220L1001 STS304-2B 0.
26 7. REPLACEMENT OF MAIN COMPONENTS 7-1. TOP GRILLE P ARTS - MAIN PCB or TRANSFORMER - DISPLAY PCB - DOOR LOCK or POWER SWITCH (ROCKER SWITCH) - DOOR SWITCH A.
27 REPLACEMENT OF MAIN COMPONENTS B. Unscrew the screws located on top of top grille panel..
28 REPLACEMENT OF MAIN COMPONENTS C. Unscrew the screws located on bottom of top grille panel. * Caution : When unscrewing, hold the top grille panel. Falling down top grille may cause bruise. D. Place the top grille panel on the top of the cabinet. E.
29 REPLACEMENT OF MAIN COMPONENTS F. Pull out the harness located back of top grille panel. You can separate top grille panel. You can replace power switch(rocker switch), door switches(lamp switch) and control board housing. G. To re-assemble, do reversed in order.
30 REPLACEMENT OF MAIN COMPONENTS 7-2. REPLACING DOOR A. Disassemble top grille panel as described section 7-1 A.B.C.D. B. Remove Bottom Grille by unscrewing the four screws located on each side of the Bottom Grille. C. Open the electrical box. Then uncap the door heater wire.
31 REPLACEMENT OF MAIN COMPONENTS D. The figure of the disassembled top grille panel. E. Unscrew the hinge. F. Unscrew the last screw with pushing the hinge.
32 REPLACEMENT OF MAIN COMPONENTS H. Lift the door and pull out the door heater ’ s lead wire. I. Replace the door with the new one. J. Ready the hinge as below.
33 REPLACEMENT OF MAIN COMPONENTS K. Initial position of the hinge must be as below. L. Turn the hinge 90 ˚ CW. This turning causes torsion strength of the bar spring that shuts the door(s) automatically. M. Screw the hinge with pushing it. After installation of the door(s), assemble the top grille panel.
34 REPLACEMENT OF MAIN COMPONENTS 7-3. REFRIGERA TION COMP ARTMENT ’ S P ARTS A. Disassemble lamp shield. - LAMP BULB or LAMP SHIELD - EVAPORATOR FAN MOTOR - F/D SENSOR or R/D SENSOR - EVAPORATOR DEFROST HEATER - EVAPORATOR COIL B. Disassemble Duct (A).
35 REPLACEMENT OF MAIN COMPONENTS D. Disassembe duct (B). E. Pull-out the evaporator drain pan heater ’ s leadwire. F. Figure of disassembled refrigeration compartments. In this situation, you can replace fan motor, F/D-sensor, Evaporator coil, ETC.
36 G. Replacing evaporator fan motor F-1. Pull out the fan motor ’ s connector. F-2. Unscrew the four screws which located on bottom of fan motor. H. Replacing F/D-Sensor or R/D-Sensor H-1. F-Sensor of Freezer Unscrew as illustrated below and pull-out the F-Sensor from the cover.
37 REPLACEMENT OF MAIN COMPONENTS H-3. R-Sensor of Refrigerator Unscrew as illustrated below and pull-out the R-Sensor from the cover. TSR-49SD TSR-72SD TSR-23SD H-2. D-Sensor of Freezer (Evaporator Defrost Sensor) Disassemble the D-Sensor from evaporator ’ s end plate.
38 H-5. F/D Sensor or R/D Sensor After unplug each sensor, pull-out the sensor ’ s lead wire. H-4. D-Sensor of Refrigerator Remove the absorber pad at the end of thermo-pipe and pull-out the D-Sensor.
39 REPLACEMENT OF MAIN COMPONENTS A. After disassembling the duct(A) and the duct(B), get ready as below for replacing the evaporator defrost heater. B. Pull out the pins from the bottom of the evaporator using the nipper, etc. H. Split the hooks of the evaporator.
40 REPLACEMENT OF MAIN COMPONENTS D. After removing all pins, disconnect the connectors from the thermal fuse and the main E. Take apart the evaporator defrost heater from the evaporator.
41 REPLACEMENT OF MAIN COMPONENTS F. Install the new evaporator defrost heater in original position. G. Pat the evaporator defrost heater with the soft hammer.
42 REPLACEMENT OF MAIN COMPONENTS I . Assemble the pins in original positions. J. Connect the connectors of the evaporator defrost heater to them of the thermal fuse * NOTE Why is always 115 voltage d.
43 REPLACEMENT OF MAIN COMPONENTS 7-4. CONDENSING UNIT - Condensing units : Compressor, Condenser Fan Motor, Condenser Coil, Condenser Dryer.... - Others : Compressor Power Cord (Relay harness), Main Power Cord, Electrical Box, ETC. A. Disassemble Bottom Grille as described section 7-2.
44 D. Pull-out the condensing unit. REPLACEMENT OF MAIN COMPONENTS.
45 REPLACEMENT OF MAIN COMPONENTS 7-5. REPLACING CABINET FRAME HEA TER (and/or) MULLION HEA TER A. Insert the and edge of ‘–’ type screw driver into the gap between the frame and the frame cover. B. Take apart the frame cover from the frame. C. Separate the frame cover by sliding the screw driver.
46 REPLACEMENT OF MAIN COMPONENTS E. Below picture shows the inlet of the cabinet frame heater toward the electrical box. F. Uncap connectors of the cabinet frame heater. G. Pull out the heater wire from the inlet. H. Insert the new cabinet frame heater wire to the inlet, after surrounding it along the frame.
47 REPLACEMENT OF MAIN COMPONENTS I. Assemble the frame cover with the frame. Push and slide the frame cover toward corner. J. Fit the end lines of the frame cover each other. K. Fit the other side of the frame cover, too. L. Pat the frame cover with the soft hammer, etc.
48 REPLACEMENT OF MAIN COMPONENTS M. Do like above instructions in other parts (Left side, right side and top side)..
49 REPLACEMENT OF MAIN COMPONENTS N. Unscrew the screws from the mullion. O. Take apart the mullion cover from the mullion. P. Take care for the mullion heater not to be hurt.
50 REPLACEMENT OF MAIN COMPONENTS S. Pull out the heater wire from the inlet. Q. Pull out the insulator from inside. R. Uncap connectors of the mullion heater.
51 REPLACEMENT OF MAIN COMPONENTS U. Change the old mullion heater and install the new one with the gap between wires 1.2 inch. V. Insert the mullion cover(SUS) into the original pisition. T. Pull out the mullion cover(SUS) from the mullion cover (ABS).
52 REPLACEMENT OF MAIN COMPONENTS W. Connect the heater wires with the main harness and the electrical box harness. X. Cover the caps on the connection parts and press them tightly.
VISION CREATIVE, INC. 중구 남대문로 5가 526 대우재단빌딩 16층 담 당 성기린 님 TEL MODEL TSR-23SD/49SD, TSF-23SD/49SD(영) BUYER 1차 2001.10.20 6차 2001.12.15 2차 2001.10.24 7차 2001.12.18 일 정 3차 2001.11.2 8차 2001.12.20 4차 2001.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Turbo Air TSF-72SD c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Turbo Air TSF-72SD - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Turbo Air TSF-72SD, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Turbo Air TSF-72SD va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Turbo Air TSF-72SD, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Turbo Air TSF-72SD.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Turbo Air TSF-72SD. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Turbo Air TSF-72SD ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
